|
Supply/ Installation/ Testing And Commissioning Of Various Equipment For Establishment Of Workshop In The Office Premises Of Flood Mechanical Division Baramulla.- Supply, installation, testing and commissioning of Heavy Duty 25mm capacity, pillar Type Drilling Machine. The specifications of the machine shall be as under: Type: Manual Feed, geared, with fine feed, complete with drive motor, pulleys & v-belts etc. • Drilling Capacity in Mild Steel 25mm • Spindle Nose Taper , MT3 or MT4 • Spindle Speed Range, rpmMin 70, Max 2800 • Spindle Travel, mm Min 140 • No. of speeds 8 • Distance Spindle to Column , mm Min 225 • Column Diameter, mmMin 88 • Column/ Pillar Length, mm Min 1200 • Distance Spindle to Table , mm Min 600 • Max. Distance Spindle to Base, mmNot less than 1000 • Table size,dia / mm x mm Min Dia 330 or Min330 x 330 • Table Travel, mmMin 415 • Motor Min 1HP, 3Phase,(1400-1440)RPM • Overall Base size mm x mm • Overall Weight, Kg Approximately 200 to 400 • Accessories included: All standard accessories including but not limited to Machine Suitable 1. Drill Chuck with Key and Arbor 2. Coolant Pump 3. Machine Lamp 4. Machine Vice 5. DOL Starter 6. R/F switch 7. Drill-bit angle gauge 8. Manual Book Installation at site, complete in all respects including providing and fitting of wires/ cables / switches etc as required. 2 SITC of Grinding machine (Bench type) of following specifications Wheel Size (inch)8 x 3/4 Grinding Wheels 2 nos. Frame High Grade Cast Iron body with wheel guards Shaft High Carbon Steel RotorDynamically Balanced Motor 0.5Hp, 230V 1Phase , min2500rpm Duty S1 MS Pedestal stand and coolant system Coolant pump >=0.15Hp, 1phasemin2500rpm Coolant Pump Tank Min 15 ltrs Installation at site, complete in all respects including providing and fitting of wires/ cables / switches etc as required. 3 Electric Angle Hand Grinder of following minimum specifications • Typecorded electric angle grinder • Power Input>=750 W • Disc diameter4inches • No-load speed >=10000 • Spindle Thread M10 • WeightApprox.2kg • Motor >=0.5Hp,230V,1phase • SwitchSlide Switch Type • Grip DesignErgonomic handle for comfortable grip • Safety FeaturesProtection Guard, Lock on switch • Accessories 1. Pin-type face wrench 2. grinding disc 3. cutting disc 4. protective guard 5. Spanner wrench 6. User manual 4 Providing Fitting and testing of Oxygen Gas Cutting System conforming to Gas Cylinder rules (IS 3196 (Pt. 1) of 2006) and latest relevant IS codes. The Job comprises: Providing and fitting of 1.01 No. 07 Cum Oxygen Cylinder with necessary clear, readable & permanent markings, including Inspector's stamp, as applicable, including but not limited to: a) Serial No, abbreviated name, monogram of the manufacturer and identification of the owner. b) Maximum working pressure in MPa (kgf/cm2). c) Test pressure in MPa (kgf/cm2) and date of hydrostatic test d) Number of Indian Standard e) Tare weight in kg f) Gross weight in kg g) Water capacity in litres and h) Letter ‘N’ or ‘SR’ next to IS Number, if the cylinder is normalized or stress relieved i) (Note: - The Tare weight shall include the weight of the valves fitted to the cylinder). 2. Gas pipe20Mtrs a)10 for Oxygen and b)10 for LPG as per colour code 3. Cutter (Torch) Assembly01 N0. 4. Oxygen Regulator /Gauge (2 in 1) 01 Set 5. LPG Cylinder, Commercial, 01 No (with necessary clear, readable & permanent markings, including Inspector's stamp, as applicable). 6. LPG Regulator /Gauge (2 in 1)01 No 7. Spanner 01 No 8. clips 06 No Note: Necessary inspection / test certificates to be provided in respect of the items, as applicable by industrial norms.
|
