|
Mountable Steel Cabinet With 02 Doors Features: Made From Standard #26 (0.45Mm) Cold-Rolled Steel Sheet On The Sides, Bottom And Doors. With Structural Locks Made Of #20 Steel Sheet (0.90Mm). A - Assembleable Product Using System Of Locks, Lever And Nail, Developed In High Stamping Technologies, There Is No Need To Use Screws. B - Upper Lock Made Of Steel Plate #20 (0.90Mm) With 3 Perpendicular Folds, The 1St At 25Mm With 90°, The 2Nd At 25Mm With 90°, The Third At 15Mm With 90° And Ends With 10Mm, And With Lever System For Locking On The Sides. C - Lower Lock Made Of Steel Plate # 20 (0.90Mm) 2 Perpendicular Folds, The 1St At 20Mm With 90°, The 2Nd At 45Mm With 90° And Ends With 15Mm And With Lever System For Locking On The Sides. D - Doors With Overlapping Closure With Left And Right Measurements Of 432Mm(W)X1920mm(H) In Steel Sheet #26 (0.45Mm), Left Side Molded By 2 Folds With The 1St At 390Mm With 225°, The 2Nd At 20Mm With 135° And Ends With 30Mm, And Right Side With Stamped Handle System Characterized By 4 Folds, The 1St At 388Mm With 315°, The 2Nd At 20Mm With 45°, The 3Rd At 25Mm With 90°, The 4Th At 15Mm With 90° And Ends With A 360° Curved Bend, Finished In Pvc Profile In Crystal Gray Or Graphite, 3 Reinforcements In Omega Horizontally And 1 Vertically In Cold Rolled Steel Sheet #26 (0.45Mm). With 4 Folds, 1St At 5Mm With 90°, 2Nd At 15Mm With 90°, 3Rd At 25Mm With 90°, The 4Th At 15Mm With 90° And Ends With 5Mm With Ventilation Hole In The Top Corner Of Each Door With 15 Circular Holes With 6Mm Diameter In Triangular Formation With 15Mm Spacing Between Holes, Without Hinges, With Pivoting Articulation Using Sup Fastfixx Washer Pin With Fitting In Hole In The Upper Part Of The Door, Locking In The Lower Part Of The Shelf Above And Lower Fastfixx Pin For Fitting In The Part Lower Door To A Nylon Bushing Fixed To The Base Shelf, With A Stand, Steel Bookcase With 06 Shelves Features: Detachable Steel Bookcase With 06 Shelves 2000Mm High By 920Mm Wide And 450Mm Deep. Shelves: 06 (Six) Shelves Made Of Steel Sheet # 22 (0.75Mm) In Measurement Of 30Mm(H) X 915Mm(W) °, The 2Nd At 30Mm With 90°, The 3Rd At 915Mm With 90°, The 4Th At 30Mm With 90° And Ends With 12Mm) And Triples On The Front And Back Parts (6 Perpendicular Folds With The 1St Fold At 10Mm With 90° , The 2Nd At 10Mm With 90°, The 3Rd At 30Mm With 90°M, The 4Th At 450Mm With 90°, The 5Th At 30Mm With 90°, The 6Th At 10Mm With 90° And Ends With 10Mm), With 2 Omega Type Reinforcements On The Internal Part Measuring 20 X 40 And The Back Of The U-Shaped Shelf Made Of Steel Sheet #14 (1.90 Mm), Measuring 27.5 Mm (H) 2Nd To 27.5Mm With A 90° Curved Bend And Ends With 32.5Mm Fixed To The Front And Back Of The Shelf Using A Fusion Welding System. . Following The Provisions Of Item 4.4.2 Of Abnt Standard 13961:2010 With Rounded Edges And Free Of Burrs, And Must Not Have Sharp Edges As Per The Sharp Edge Test (5.8 Da Nm 300-1). Columns: 04(Four) Columns Made From Steel Plate #14 (1.90Mm) Measuring 2000Mm Height Fold Per
|
