|
Tender For For Supply, Installation, Testing And Training Of Fire Hydrant System- 1 FIRE PUMPS & ACCESSORIES 2 Supply of main fire pump (MFP / EP) suitable for water discharge of 2280 LPM at 56 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 37kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-F insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP(Make - Kirloskar) 3 Supply of jockey fire pump (JP) suitable for water discharge of 180 LPM at 56 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-F insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP(Make - Kirloskar) 4 supply of150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFVMake - Lehry/ Intervalve/Zoloto 5 Supply of 100 mm dia. cast iron double flange butterfly valve ofsize complete with PN16 pressure rating, as per specification no. FF-VL/BFVMake - Lehry/ Intervalve/Zoloto 6 Supply of75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFVMake - Lehry/ Intervalve/Zoloto 7 Supply of 50 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFVMake - Lehry/ Intervalve/Zoloto 8 Supply of100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRVMake - Lehry/ Intervalve/Zoloto 9 Supply of75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRVMake - Lehry/ Intervalve/Zoloto 10 Supply of 80 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FVMake - Kirloskar/Kartar 11 Supply of 150 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FVMake - Kirloskar/Kartar 12 Supply of 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG(Make- H.Guru,Viking,Indfoss) 13 Supply ofLever operated Ball valve made of Cast Iron conforms to IS 9890 -15mm dia Make - Kartar/Atom/Zoloto 14 Supply of12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PSMake : Danfoss/Baumer/switzer/schneider) 15 Supply of 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT 16 Supply of Lever operated Ball valve made of Cast Iron conforms to IS 9890 -25mm diaMake - Kartar/Atom/Zoloto 17 Supply of 500 liters pvc priming tank 18 Supply of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey (pressurisation) pumps (1working+1standby) with necessary accessories, wiring & cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specifications the capacity of electric motor driven pump are as followsa. Main fire pump(MFP) having capacity of 37kW 1no (1 working) b. Jockey pump(JP) capacity of suitable capacity 1 nos(1 working)comprises of the following features & switchgears: 1. Main incomer FP SFU having rotary handle with HRC fuses of suitable rating.2. Electrolytic grade copper strips for busbar of suitable sizes for main incomer and branches to motor SFUs, starters & outgoing terminals with necessary accessories like stainless steel nut bolts with spring washers for connections, mounted on required no of epoxy or porcelain support insulators of suitable ratings etc. 3. Individual pump TPN SFU having rotary handle with HRC fuses of suitable rating. Each 182320 4. Digital voltmeter & ammeter & RYB indicating lamps & push buttons & SPP, O/L & phase reversal protection with emergency stop switch. 5. TPN SPD 100kA Type 1 +2 tested. 6. Required pressure transducer with pressure indication on panel with cabling required for monitoring & automatic operation of fire pumps. 7. System controller to control operation of main electric fire pump, jockey (pressurization) pumps in sequence with interlocking for operation of pumps as per specification with automatic/manual operation with selector switch & alternate run of standby Pumps consisting of relays, timers. sensors, annunciation window for fault indication, complete as per specification. 8.Suitable capacity electric motor starters for all individual pumps with necessary push buttons & indications. 9. Siren of required capacity to be activated when main pump starts & allied accessories as per requirements of local CFO or as directed by engineer in charge. 10. Danger board as per IS. 11. Spare HRC fuses minimum 2nos of each individual rating with required bakelite fuse holder for main & jockey fire pumps MFP=(1working), JP = (1working+1standby, alternate run per start in auto mode) complete panel, as per specification no. FF-MFP/ECP 19 Installation, Commissionig, Testing & Trainig Charges for the Fire Pump & Accessories 20 FIRE FIGHTING EQUIPMENT 21 Supply of 01 run PVC insulated and PVC sheathed armoured Aluminium power cable of 1.1kV grade of following sizes using clamps knoted along with the cables, spacing of clamps not exceeding 60cms, making good the damages, colour washing ..etc as required3.5C x 400 Sq.mm Al Armoured cable Make - Polycab 22 Supplyof 01 run PVC insulated and PVC sheathed armoured Aluminium power cable of 1.1kV grade of following sizes using clamps knoted along with the cables, spacing of clamps not exceeding 60cms, making good the damages, colour washing ..etc as required3.5C x 120 Sq.mm Al Armoured cable Make - Polycab 23 Supplyof 01 run PVC insulated and PVC sheathed armoured Aluminium power cable of 1.1kV grade of following sizes using clamps knoted along with the cables, spacing of clamps not exceeding 60cms, making good the damages, colour washing ..etc as required3.5C x 35 Sq.mm Al Armoured cable Make - Polycab 24 Supply end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kV grade as required.3.5x400 sq.mm (82mm)Make - Dowells/HMI/Comet 25 Supply end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kV grade as required.3.5x120 sq.mm (45mm)Make - Dowells/HMI/Comet 26 Supply end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kV grade as required.3.5x35 sq.mm (32mm)Make - Dowells/HMI/Comet 27 Supply M.S./CRCA cabinet for housing double hose pipe with nozzle (size 750 x 600x 250 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8x6) and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)Make -Safex/Kartar/AAAG 28 Supply of gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HVMake - Newage/Kartar/AAAG 29 Supply 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL Make -Newage/ Arihant/AAAG 30 Supplyof wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long braided rubber/thermoplastic hose along with necessary accessories complete as per specification no. FF-FFA/HV(IS 844 -1985) Make -Newage/Safex/AAAG 31 Supply of Gun metal chrome finished Ball valves of 50mm dia (PN 1.6) with fittings of screwed end type.Make - Kartar/Atom/Zoloto 32 Supply of gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FFFFA/NZMake -Newage/ Arihant/AAAG 33 Supply of 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARVMake - Kartar/Zoloto/ATAM 34 Supply of 4 way fire brigade inlet of 150 mm dia, for supplying water in fire tank complete as per specification no. FFFA/FMCMake - Newage/Kartar/AAAG 35 Supply of 150 mm dia 4 way fire brigade inlet suitable for supplying water to the hydrant system complete as per specification no. FF-FA/FBCMake - Newage/Kartar/AAAG 36 Supplyof G.I. pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings complete as per specification no. FF-PPMake - Jindal/Tata 37 Supply of G.I. pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings complete as per specification no. FF-PPMake - Jindal/Tata 38 Supply of G.I. pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings complete as per specification no. FF-PPMake - Jindal/Tata 39 Supply of G.I. pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings complete as per specification no. FF-PPMake - Jindal/Tata 40 Supply of G.I. pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings complete as per specification no. FF-PPMake - Jindal/Tata 41 Installation, Commissionig, Testing & Trainig Charges for the Fire Fighting Equipments
|
