|
Engine Room Maintenance. Control Station Inspection And Maintenance, To Carry Out Maintenance Of The Access Device, Fixing The Wires In The Controller, Electrical Contact In The Connection Points Of The Power Wires To The Motor, The Controller And The Electromagnetic Brake, Maintenance Of The Brake: - Before Checking The Brake, Place The Counterweight On The Buffer - Check The Brake And Make Sure That There Is No Mechanical Damage To Its Components - Clean The Brake Of Impurities. When Greasing The Bearings, It Is Necessary To Wash And Clean The Brake Pulley - Check And Tighten The Fastening Of The Parts - Check The Clearances, Adjust If Necessary In Accordance With Paragraphs 3.6.6 And 3.6.5 Of The Ti Of The Winch - Check The Accuracy Of The Cabin Stops On The Floors, The Required Accuracy Is Obtained By Cleaning The Brake And Changing The Locations Of The Magnets On The Shaft, Respectively, In Paragraph 3.6.1 Of The Ti Of The Winch., Technical Service Of The Reducer And Winch Frame: - Clean The Reducer And Winch Frame From Dirt. - Check The Reducer And Frame - Check The Welding Seams And Threaded Connections - Check The Oil Level In The Reducer - Check The Oil Leakage In The Places Where It Is Installed On The Cover And Shafts - Change The Oil In The Reducer - Check The Disintegration Of The Screw Pair Of The Reducer By Measuring The Side Gap According To The Ti Of The Winch, Maintenance Of The Winch Pulley (Kash) And Pulley Block: - Stop The Cabin At The Upper Stop - Clean The Kash And The Block From Dirt, Check And Tighten The Fastenings - Check The Kash And Block Supports, Change If Necessary (Paragraph 4.3 Of The Winchs Ti), Speed Limiter (Sm) Maintenance:-Remove The Seal From The Sm-Clean The Dirt From The Sm-Check The Condition Of The Components And Elements Of The Sm With An External View-Tighten The Fastening Of The Non-Sealed Components And Elements-Check The Contact Of The Sm-Press The Link Of The Contact Of The Sm And Release The Cabin-Check The Tightness Of The Support Of The Sm With An External View-Seal The Sm, Maintenance Of The Final Circuit Breakers Of The Correction Race:-Check And Clean The Device That Ensures The Operation Of The Circuit Breakers When The Cabin Passes The Last Operating Position-Check The Movement Of The Elbow To The Ling Of The Extinguishers. To Check The Operation Of The Last Circuit Breakers, Raise (Lower) The Cabin 50 Mm Above (Lower) The Level Of The Upper (Lower) Stop By Turning The Control Wheel And Release The Elevator For The Sample, Maintenance Of Tension Ropes And Ropes Of Sm: - Clean The Pulleys Of Tension Ropes And Pulleys From Impurities - Check The Condition Of Pulleys Along Their Entire Length. To Carry Out The Test With Separate Parts Of 2M Length In The Switched Off State Of The Input Device., Maintenance Of Magnets And Indicators Of Directional Devices, Electrical Apparatus And Electrical Disconnectors: -Cleaning Magnets, Tightening The Supports -Checking The Interaction Of Cabin Indicators With Magnets Installed On The Portal, Adjusting If Necessary -Carrying Out Maintenance Of Call Posts And Light Indicators -Checking The Condition Of Electric Disconnectors, Maintenance Of Frosted Doors: -Cleaning Of The Equipment (Rulers, Wheels, Contour Wheels, Rasps, Electric Switches) -External Inspection Of The Doors And Checking The Condition Of Their Component Parts Fastening, Check The Adjusted Gaps, If Necessary, Adjust The Doors According To Ti:-Adjust The Gaps Between The Rollers Of The Locks And The Sides Of The Elbows Of The Cabin Doors When The Shutters Are Covered-Adjust The Depth Of The Entrance To The Elbow Groove Of The Lock Rollers-Repeatedly Check The Operation Of The Control And Rasa Block When Each Lock Works, Maintenance Of The Cabin:Maintenance Of The Undercarriage, Cabin Suspensions, Holders And Suspension Cables:-Cleaning The Undercarriage-Inspecting And Tightening The Fastenings Of The Undercarriage-Checking The Lateral And End Face Gaps Between The Lining And The Guides-Cleaning The Suspension-Checking The Condition Of The Welding Seams Of The Main Elevators And Their Fastening Of The Components Of The Suspension-Checking The Movement Of The Spk Electric Block Switch And Releasing The Elevator-Cleaning The Holders And Their Wires, Check The Condition Of Fastenings - Check The Distance Between The Guides Of The Cabin And The Housing Of The Holders - Check The Movement Of The Wheels Of The Holders And Their Contact With The Guides At The Same Time - Check The Movement Of The Electric Block Switches Of The Holders - Check The Condition Of The Cable, Electrical Equipment, Grounding Wires, Technical Service Of The Load-Carrying Device: - Check The Condition Of The Car-Loading Device And The Operation Of The Micro-Switches With A Visual Inspection, Maintenance Of The Cabin Compartment: - Check The Condition Of The Compartment And The Equipment Installed Inside It - Carry Out Maintenance Of The Button Post
|
