|
1 Providing & Fixing of IK07 IP-66 protected high power LED floodlight system with Pressure diecast aluminium housing LM6/ ADC12material , toughened glass diffuser with suitable lenses on LED toachieve various beam angles, 240 volt, 50Hz, of high power LEDlamps . Integrated driver must be potted & has a unique BIS Rnumber shall be high efficiency having efficiency more than 85 %and in compliance to BIS certified and T.C. certificate. The Systemlevel Luminaire efficacy >=120 lm/ wt with High Power LEDs is to beused . LED driver Input Voltage AC 120 to 270 V AC with Highvoltage Cutoff @>=300 V AC and Auto resetting Safety . InputFrequency 50Hz±3%, Power Factor >0.95 ,driver Efficiency >85% ,THD(I) <10% , driver current <1000mA shown in LM79 report. drivershould be Phase to phase protection of 440 V for 4 Hrs. ElectricalConnector Must be provided, Surge Protection Min >=4KV internaland 10KV external, System life of 30000 Burning hours with 70% ofInitial Lumens maintained, color Rendering Index >70 and CCT5700K ±355K. Driver current <1000mA shown in LM79 report.Manufactures Word Mark/Name Engraved/Embossing/Screenprinting on die cast housing to allow traceability/authenticity. Fixtureshall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79/LM80) Certificate/ report withliable warranty of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure Aattached with this BSR ..High Power LED Flood Light 240W 2 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured/ Armoured aluminium cable of 1.1 KV grade as perPWD specification for electrical Works in existing RCC / Hume /Stoneware / PVC pipe/ open duct/cable trench with filling ofexcavated earth in trench , on existing cable trays or on surface etc.including making necessary connection, testing etc. as required ofsize and as per points (a), (b), (c), mentioned below:-(a) Material :- H4- Grade aluminium conductor of purity >99.6 % &as per IS:1554 P-I / IS :7098 P – I(b) conductor shall have electrolytic aluminium confirming to IS8130, IS 3975-1999 for armouring of cables in armoured cableitems , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testingprocedures.(c) OEM Must have ISO 9001 & 14001 certifications for qualityassuarance & its own in house NABL lab setup for all testingfacilities for cables . Appropriate type test certificate / OEM testreport shall be submitted . All above as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure A attached with this BSR.2.5 sq.mm 5 core 3 Supplying and drawing FR PVC insulated & unsheathed flexiblecopper conductor as per PWD specification for electrical Works withISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wireshould be made from 99.99% purity copper, class 5 stranding inacc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) forless chances of oxidization and higher silver content for gives betterconductivity , insulation PVC type A or C ,flame retardant as per IS10810-53, better amperage rating as per VDE 0298 part 4, , inexisting surface or recessed PVC/ MS conduit/casing cappingincluding all as per pre approved by Engineer in charge,makingconnections, etc. as required. OEM Must have its own in houseNABL lab setup for all testing facilities for wires. For additionaltechnical parameters of products/ work , refer Annexure Aattached with this BSR .2 x 1.5 sq.mm 4 Supply installation testing & Commissioning of ISO certifiedcompany made high mast lighting system (as per PLG 07 of ILP UKtechinical report no 7 of ILE UK /IS:875 Part-1 –2015//BSEN10025/and IS:2062 )consisting of totally hot dipgalvanised by single dipped method high mast, lantern carriagesuitable for up to 12 nos luminaries with welded arm (excludingluminares), mast head frame assembly with full cover, including 1No. LED 15 Watts aviation obstruction lights, double drum type selfsustaining winch, integral power tool accesible from door withpadlocking arrangement ( winch motor with control circuit) hotdipped galvanised heavy duty pipe lightening finial, S.S. ropes (AISI316, 7 / 19 costruction ), EPR insulated PCP sheathed trailing cable,including outdoor type control panel for auto on / off, reverse /forward motor operation and CC foundation of M - 25 gradecomplete as required as per IS 456/IS 2911. The mast isconstructed from mild steel plates (as per IS 5986 Gr. 510 ) cut andfolded to form a polygonal section, telescopic jointed and welding asper BS 5135. ( See table P - 03 for specs.)OEM Must have Type test certificate for wind tunnel test for Highmast fixtures. complete in all respect. All as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure A attached with this BSR .16.0 Mtr HM (in 2 section) 5 SITC of chemical Gel earthing system of Dual Pipe Technologymade of with B Class G I Pipe as per IS 1239 ( part-1):2004 ofMedium duty of following sizes as per points mentioned (a), (b), [c),(d), (e) below :-(a) filled with anti corrosive conductive compounds with thepermanent sealings at both the ends, CPRI/ ERDA tested with RMScapacity of minimum 35- 40 KA for withstanding 1 second .(b) To ensure the moisture content and electrical conductivity, 25 kgfor 2000 mm & 50 Kgs for 3000mm of resistance lowering earthenhancement material shall be used as a backfill compound. Thecompound shall be tested form NABL acredeated lab for lowresistivity ( less than 0.12 Ohm - meter) & high conductivity in naturewith carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 withlatest amendemnts(c) Heavy duty weather proof poly-propylene earth pit chamber withlockable Jam free lid suitable for safe working load 5000 Kg or moreof size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. andHeight 250 to 300 mm.(d) Testing of earth resistance for value of 5 ohms or less asrequired & must record by engineer in charge during site visit andensure to enter in measurment book.(e) Self certificate for confirming above standards from OEM ismandatory. All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer AnnexureA attached with this BSR .With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. )Minimum 100 mm dia borewellGI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip
|
