Tender For Major Repair Work At Gsss Dholadanta Block Masuda Distt Ajmer - Civil Work 2 Replacing Broken Roo ... in India

Work Detail

Tender For Major Repair Work At Gsss Dholadanta Block Masuda Distt Ajmer - CIVIL WORK 2 Replacing broken roofing slab in patches including limeterrace celling plaster etc including removal of broken slab 3 Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material with in 50 Mtr. Lead 4 Demolishing cement concrete manually by mechanical means including disposal of material within 50 Mtr. Lead. As pe direction of engineer incharge. 1:3:6 or richer mix. 5 Dismantling old plaster or skirting, ranking out joints and cleaning the surface of plaster including disposal of rubbish to the dumping ground within 50 meter lead. 6 Gradingroof for water proofing tratment with water proofing compound cement concreate 1:2:4 (1cement :2coarse sand :4 graded stone sggregate 20mm nominal size) 7 Crazy marble stone flooring 20mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mixin proportion of 4 : 7 (4cement: 7 white black or white or black marble chips) size from 1mm to 4mm by volume and under layer of 25mm thick cement concrete [1:2:4, graded stone aggregate 12.5mm nominal size] rubbing and polishing and cement slurry etc. complete :In ordinary cement. 8 Providing Gola 75 mm x 75 mm in cement concrete (1:2:4) (1cement : 2 coarse sand :4 stone aggregate 10mm and down gauge)including finishing with cement mortar 1:3 (1 cement : 3 coarse sand )as per standard design. 9 PCC:Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level M 10 grade nominal mix1:3:6(1 cement:3 Coarse sand :6 graded stone aggregate 40 mm nominal size). 10 Plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finished 20 mm thick 11 Kota Stone slabs flooring 25mm thick over 20mm (averege) thick base laid over and jointed with Grey cement Slurry mixed with pigment to match theshade of the Slab including rubbing and Polishing complete with base of cement mortar 1:4 (1 cement : 4 coare sand) For area of each slab from 2001 to 5000 sqcm. 12 Providing and Fixing T-iron frames for door and windows and ventilators or mild steel tee sections joined mitered and welded with 15 x 3 mm lugs, 10cm . Long embedded in cement concrete blocks, 15 x 10 x 10 cmof 1:3:6 (1 cement, 3 coarse sand and 6 graded stone aggregate 20 mm nominal size or with wooden plugs and screws or rawl plugs and screw or with fixing clips or with bolt and nuts as require including fixing of necessary butt hinges and screw and applying a priming coat of approved steel primer 13 Providing and fixing M.S. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paintADD 20% Extra for double leaf shutters. 14 Supplying & fixing fixed wire Gauge of 14 mesh X 24 Gauge to the Metal frame of rolled section by metal beading 20X3mm with suitable screw at not exceeding 150mm distance. 15 Providing and fixing square bars or other flat welded to window ventilators etc. 16 Providing and fixing to existing door frames 30mm thick factory made PVC door shutter made of stiles and rails of a uPVC hollow section of size 60x30mm and wall thickness 2mm +/- 0.2mm with inbuilt decorative moulding edging on one side. The stiles and rails mitred and joined and the corners by means of M.S. glavanized/plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screws. the stiles of the shutter reinforced by inserting galavnized M.S. tube of size 25x20mm and 1mm +/-0.1mm wall thickness. the lock rail made up of "H" section, a uPVC hollow section of size 100x30mm and 2mm +/- 0.2mmwalll thickness fixed to the shutter stiles by means of plastic/galvanized M.S. tube "U" cleats. the shutter frame filled with a uPVC multi-chambered single panel of size not less than 610mm, having overall thickness of 20mm and 1mm +/- 0.1mm wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6mm galavanized M.S. rod and fastened with nuts and washers complete as per manufactures specification and direction of engineer-in-charge. (for W.C and bathroom door shutter) 17 Providing and fixing Ist quality standard white grey ivory fume red brown light green light blue and other light shade glazed tiles confirming toIS 15622 of size 200mm x 300mm in walls floors steps pillars etc. laid over a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tiles complete. Excluding the cost of cement plaster on walls and pillers. 18 PANTING ON DOORS & WINDOWSPainting with synthetic enamel paint of approved brand and manufacture to give an even shade :newwork (2 or more coat ). 19 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 20 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding new work (two or more coat applyied @1.67 lt. per 10 sqm over an including base coat of water proofing cement paint applyied @ 2.20 k.g. per 10 sqm. 21 Lettering with black Japan paint of approved brand and manufacture. 22 SANITORY WORK 23 P & F WVC Wash basing 1STquality IS: 2556 mark of appd make with bracket duly painted 1 no. 15mm CP pillar cock (IS: 8934mark) & 32mm CP brasswaste couplingof appd. Make , pvc waste pipe with pvc nut 32mmcomplete inc. cutting & making good the wall. Size 450x 300mm 24 Provinding and fixingindian type white glazed vitreous china 1st quality W.C. orissa Pan (IS: 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor. Size 580 x 440 mm 25 P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor 26 P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Flat Back (small) size 456x355x265mm. 27 P & F Bib Cock (IS : 8931 Mark) superior quality of approved make.Brass 400 gm, 15 mm nominal bore. 28 P&FFlushCock / FlushValve (IS :9758Mark)forWCofapproved quality make :Cp brass push type exposed 25mm nominal bore. 29 P&F GI Pipes (External Work) with GI fittings excluding union (IS: 1239 Mark) including trenching and refilling earth etc. 15 mm dia nominal bore B Class 30 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 160mm dia 31 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110mm dia 32 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Bend 87.5160mm dia 33 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:SOKET PLUG 160mm dia 34 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500litres capacity. 35 ELECTRIAL WORK 36 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure "A" attached with this BSR.25mm dia. 37 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it"sISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure "A" attached with this BSR. Short point(up to 3 mtr) 38 Medium point (up to 6 mtr.) 39 Long point(up to 10 mtr..) 40 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it"s ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure "A" attached with this BSR.On board 41 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure "A" attached with this BSR.3 x 2.5 sq.mm 42 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure "A" attached with this BSR.6 A to 32 A rating 43 50/63 Arating 44 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure "A" attached with this BSR.Metal door (single phase) IK-09 and IP-43 with Metal end box.4Way(4+2) 45 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .1170mm(+/-10%) LED batten with min. lumen output 2200 lm 46 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) 47 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure "A" attached with this BSR.5 step fan regulator 2 Module 360 dgree rotating 48 P & F 1.2 mm thickG. I. / M .S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required.For additional technical parameters of product / work refer Annexure "A" attached with this BSR.1.2 mm thickM. S. Sheet boxes .175mm x 100mm x 60mm 49 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass coverand secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver& has a unique BIS R number withInput Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driverEfficiency >85%,THD(I) <10%Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <750mA. The luminaireshall be BIS certified and Trade mark certified. Life ExpectancyEqual or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs.Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .LED Street Light fixture with Minimum lumen output 7500 lm

Contact Information