Tender For Reconstruction Work Of Durjanpur Hariyapur Road Bjlighar To Hardev Singh Ke Farm Ka Remaning Port ... in India

Work Detail

Tender For Reconstruction Work Of Durjanpur Hariyapur Road Bjlighar To Hardev Singh Ke Farm Ka Remaning Portion - Construction of Subgrade and earthen shoulders with apporved material obtained from borrow pits with attl ifts and leads transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2 with a lead upto 1000 m as per Tecnical Specification Clause 303.1 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100KN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting torequired density complete work.(WBM Grading-2) 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100KN in stages to proper grade and camber, applying and brooming, stonescreening to fill up the interstices of coarse aggregate, watering and compacting to the required density complete work.(WBM Grading-3) 4 Providing and applying primer coat with Bitumen emulsion (SS-2) on prepared surface of granular base including cleaning of road surface and spraying primer at rate of 0.70 Kg/Sqm using mechanical means as per Technical Specification Clause 5.1-502. 5 Providing and applying tack coat with Bitumen (VG-10) using emulsion distributor at the rate of 0.35 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 5.2-503(iii) 6 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type as per Technical Specification Clause 5.9-508. 7 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 5.12-510. 8 Brick edging on both sides of the road of first class bricks 8 cm (3") wide and 12 cm. 4½"deep laid with mud mortar including labour and supply of. bricks finished to required template and proper alignment and also including dressing and ramming the excavated earth as directed by Engineer-in-Charge. SOR 765. 9 Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 10 Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 11 Suply and Fixing of M.S. informatory board wide up of 75x75x5mm angle iron (vertical post length 1.95mtr), 40x5mm flat cross angle 1mm thick ms sheet (0.90x0.90 sqm) including exavation of pit (0.45x0.45x0.60 cum), CC1:5:10 cement fine sand and Brick Balast 10cm thick, and cc 1:2:4 cement course sand & 20mm grit (0.45x0.45x0.60 cum), Two coat painting latter writing up to 2.5cm size (225 no)etc complete as per Engineer-in-incharge

Contact Information