|
Tender For Construction Of Gst Office Building In District Amethi - Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2 Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundationtrenches, plinth, sides of foundation etc. complete for all lift. 3 Earth work in exacavation in ordinary soil(loam clay or sand) including lift upto 1.5 m and a lead of 30m includingfilling watering & ramming of exacavtion earth into the trenches or into the apce between the building &the side of foundation trenches or to the plinth remonal &disposal of surplus excavated earth as directed by the Engineer i/c with in .including royality 4 Sand filling in plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift upto 1.5m and including cost of sand. 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 6 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaRM holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 7 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)all work upto Plinth 8 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 9 R.C.C. work in Lintel Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). GF,FF,SF,TF 10 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 11 Brick work with bricks of class designation 15 (Class-150) in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)) 12 Brick work with bricks of class designation 15 (Class-150) in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)) 13 Half brick masonry with bricks of class designation 15 (Class-150) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand (FM 1.50 to 2.00)) 14 Providing and laying Cement concrete 1:2:4 (1cement :2 coarse sand :4graded stone aggregate 20 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation. 15 Providing & applying a coat of residual petroleum of grade of VG-10 of approved qualiy using 1.7 kg per square RM on damp proof course after cleaning the surface with brushes and finally with apiece of loth lightly soaked in kerosene oil. 16 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatmentWith average thickness of 120 mm and minimum thickness at khurra as 65 mm. 17 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 18 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 19 Columns, Pillars, Piers, Abutments, Posts and Struts 20 Lintels, beams, plinth beams, girders, buttresses and cantilevers. 21 Suspended floors, roofs, landings, balconies and access platform. 22 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :35 mm thick Single leaf 23 35 mm thick Double leaf 24 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Fabrication of holdfast for door, chaukhats and windows. 25 Providing & fabricated of door / windows grill. 26 Z-Section steel windows (openable) 27 Angle iron door chaukhats 40*40*5 28 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows & doors with using M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading 29 Fixing of Door, windows / ventilators chaukhats in position. (a) Door chaukhats 30 (b) Window chaukhats 31 (c) Ventilator chaukhats 32 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 coarse sand) 33 12 mm cement plaster of mix : 1: 6 (1 cement : 6 coarse sand) 34 20 mm cement plaster of mix : 1: 6 (1 cement : 6 coarse sand) 35 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. 36 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 37 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate 38 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,.Size of Tile 600x600 mm 39 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to |.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 40 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 41 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 42 Supply and fixing 6 mm Ceramic white glazedtiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and tool sand plants etc. required for proper completion of the work. (Size of tiles upto 300x300mm). 43 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 44 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 Itr/10 sqm over an under coat of primer applied @ 0.80 Itr/10 sqm of approved brand and manufacture 45 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture 46 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm 47 Finishing walls with Acrylic smooth exterior paint of required shade: - New work (Two or more coat applied @ 1.43 Ltr./10 Sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm. 48 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 49 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : (a) 4.0 mm thick glass panes 50 Providing & fixing ISI marked oxidiesd M.S. sliding door with nuts and screw etc.complete.(copper oxidiesd as per IS 1378)(a) 250mm x 16mm 51 Providing & fixing ISI marked oxidiesd M.S. tower bolt black finish,(Barrel type) with necessary screws etc.complete.(copper oxidiesd as per IS 1378) (a) 250 mm x 10mm 52 Providing & fixing ISI marked oxidiesd M.S.handles conforming to IS 4992 with necessary screws etc.complete.(copper oxidiesd as per IS 1378) 125 mm 53 Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete 54 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. 55 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 56 Providing & laying of light cinder filling under floor of toilets & other sunken roofs. 57 Providing & laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment & all corners, junctions of pipes with polymer mixed slurry. 58 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 59 Cnstruction of Apron drain 60 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing "C" wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the periRM of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending 61 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 62 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 63 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: hite Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 64 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required : 65 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 MM Dia 66 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 MM Dia 67 Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. 68 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 RM long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge. 69 SOIL WASTE & VENT PIPES AND FITTINGS - II Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 150 mm 70 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110 mm 71 WATER SUPPLY PIPES AND FITTINGS - III Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply and all CPVC plain & brassthreaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solventcement and testing of joints complete as per direction of Engineer inCharge.Internal work - Exposed on wall 25 mm dia 72 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply and all CPVC plain & brassthreaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solventcement and testing of joints complete as per direction of Engineer inCharge.Internal work - Exposed on wall32mm dia 73 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply and all CPVC plain & brassthreaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solventcement and testing of joints complete as per direction of Engineer inCharge.Internal work - Exposed on wall 40 mm dia 74 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVCplain & brass hreaded fittings and fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVCsolvent cement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 15 mm dia 75 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVCplain & brass hreaded fittings and fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVCsolvent cement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 20 mm dia 76 Providing and fixing uplasticised PVC connection pipe with brass unions 45cm length and 15 mm dia 77 Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 78 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend 79 Shoe plain 110 mm shoe 80 Single tee with door 110x110x110 mm 81 Single pushfit Coupler 110 mm shoe 82 Providing and fixing C.P. brass bib cock of approved quality conforming to 18:8931 :15 mm nominal bore 83 roviding and fixing C.P. brass long nose bib cock of approved quality conforming to |S standards and weighing not less than 810 gms.15 mm nominal bore 84 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to 1S:8931 15 mm nominal bore 85 Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) : 25 mm nominal bore 86 Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) : 32 mm nominal bore 87 Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) : 40 mm nominal bore 88 Providing and fixing brass stop cock of approved quality :15 mm nominal bore 89 Providing and fixing brass stop cock of approved quality :20 mm nominal bore 90 Making khurras 45x45 cm with average minimum thickness of 5cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 91 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 92 SCHEDULE OF QUANTITIES FOR INTERNAL & EXTERNAL SEWERAGE SYSTEM - IV Excavating trenches by mechinical / manual means of required width forpipes, cables, etc including excavation for sockets, and dressing of sides,ramming of bottoms, for all depth, including getting out the excavatedsoil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating Nos deposited layer by ramming,watering, etc. and disposing of surplus excavated soil as directed, within alead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. butnot exceeding 300 mm dia 93 Providing, laying and joining glazed stone ware pipes grade "A"with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 100 mm dia 94 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diaRM 95 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :150 mm diaRM 96 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W.dipesincluding bed concrete as per standard design :100 mm diaRM S.W. pipe 97 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W.dipesincluding bed concrete as per standard design :150 mm diaRM S.W. pipe 98 roviding and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.l. cover with frame of 300 x 300 mm size (inside) the weight of coverto be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 15 x100 with common burnt clay F.P.S. (non modular)bricks of class designation 7. 99 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 100 SEWERAGE AND DRAINAGE Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating Nos deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. 101 Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 RM 102 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1cement :1fine sand) including testing of joints etc. complete : 100 mm diaRM 103 150 mm.dia. RCCPipes 104 200 mm.dia. RCCPipes 105 250 mm.dia. RCCPipes 106 Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design: 100 mm.dia. RCCPipes 107 150 mm.dia. RCCPipes 108 200 mm.dia. RCCPipes 109 250 mm.dia. RCCPipes 110 With common burnt clay FPS (non modular) bricks of class designation 75 111 Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design.Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With common burnt clay FPS (non modular) bricks of class designation 7.5 112 Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diaRM, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :-With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 113 Extra for depth for manholes:Size 90x80cmWith common burnt clay FPS (non modular) bricks of class designation 7.5 114 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming toIS: 1786, having minimum cross section as 23 mmx25 mm and overall minimum length 263 mm and width as 165 mm with minimum 112mm space between protruded legs having 2 mm tread on top surfaceby ribbing or chequering besides necessary and adequate anchoringprojections on tail length on 138 mm as per standard drawing andsuitable to with stand the bend test and chemical resistance test as perspecifications and having manufacture’s permanent identification mark tobe visible even after fixing, including fixing in manholes with 30x20x15 cmcement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20 mm nominal size) complete as per design 115 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm dia nominal bore 116 20 mm dia nominal bore 117 25 mm dia nominal bore 118 32 mm dia nominal bore 119 40 mm dia nominal bore 120 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :-15 mm dia nominal bore 121 20 mm dia nominal bore 122 25 mm dia nominal bore 123 32 mm dia nominal bore 124 40 mm dia nominal bore 125 Providing and filling sand of grading zone V or coarser grade alround the G.I. pipes in external work. 15 mm dia nominal bore 126 20 mm dia nominal bore 127 25 mm dia nominal bore 128 32 mm dia nominal bore 129 40 mm dia nominal bore 130 Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) 20mm dia nominal bore 131 25mm dia nominal bore 132 Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design:- With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 133 Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diaRM, 160 mm bottom diaRM and180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.With F.P.S. bricks 134 Making connection to Municipal sewer / storm water drain including necessary excavation and breaking the wall of municipal manhole and making good the same with Cement mortar 1:3, finished with a floatingcoat ofneat cementandmaking drains etc.complete. Removingthe excavated surplus material.Thisalso includesthecontractor for liasoning worksuch asfillingnecessary applications,submissionofforms for approvaltothe municipal authorities, depositing and making channels for the necessary fees andother amounts asrequiredforgettingthe premises / installationsinspectedand approvedand all otherformalities requiredtillthesewer / storm water connection is obtained. All the expenses incurred in this regardshall be borne by the Contractor,exceptfor the payments to be made for any security depositswhichwillbereimbursed on production of original voucher. 135 Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. 136 Providing and fixing 150 mm S.C.I. tee at the inlet and outlet of septic tank. 137 Providing & fixing 75mm dia vent pipes. 138 Providing & fixing of 75mm dia cast iron terminal guard. 139 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diaRM 140 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. L.D. -2.5- Circular shape 450mm internal diaRM 141 Making soak pit 2.5 m diaRM 3.0 RM deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diaRM, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 142 Supply and stacking of graded stone aggregate of 45-90mm size 143 Supply and stacking ofstone chippings of 11.20mm size 144 Supply and stacking ofmoorum at site 145 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitablemethod prescribed in IS: 2800 (part I), including collecting samples fromdifferent strata, preparing and submitting strata chart/ bore log, includinghire & running charges of all equipments, tools, plants & machineriesrequired for the job, all complete as per direction of Engineer -in-charge,upto 90 RM depth below ground level.300 mm dia 146 Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia 147 Supply and fixing of nylon jali around the slotted pipes complete as required. 148 Transport of boring tools other required equipments and installation at site. 149 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 RM depth below ground level. All Types of Soil350 mm dia 150 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 RM & upto 150 RM depth below ground level.Rocky strata including Boulders 350 mm dia 151 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia having minimum wall thickness 5.00 mm 152 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia 153 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. Around Pipe 154 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. 155 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. 156 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 150 mm dia 157 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm dia 158 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 150 mm dia 159 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.80 mm dia nominal bore 160 Supplying and drawing following sizes of FRLS PVC insulatedcopper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 10 x 4 sq. mm 161 Supplyof Submersibule pump with control panel, support wire etc. complete 5.0 H.P. (KSB / EQ.) 162 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontalnegative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm 163 For horizontal surface one coat @1.10 kg per sqm. 164 Supplying and fixing C.I. cover without frame for manholes : 560 mm diaRM C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg 165 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 RMs. 166 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 167 Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). 168 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80mm thick cement concrete paver block of M-30 grade with approved colour, design & pattern. 169 Horticulture Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 170 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, byspreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). 171 Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). 172 Supplying and stacking at site dump manure from approved source including carriage upto 1 km (manure measured instacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm. 173 Carrigae of manure upto 5 K.M. 174 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge. 175 Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S (non modular) bricks of Classdesignation 7.5 176 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately 177 Providing and stacking of Nauclea cadamba (Kadam) of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge. 178 Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. 179 Providing and stacking of Phyllanthus emblica (Amla) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge. 180 Providing and stacking of Schleichera trijuga (Kusum) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge 181 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. 182 Making tree guard 53 cm dia and 2 m high as per design from empty coal tar drums, suppliedfree by the department, including providing and fixing four legs 40 cm long of 30 x 3 mm M.S.flat riveted to tree guard and providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixedwith rivets complete in all respects including painting inside and outside of tree guard with 183 Manually Operated Fire Alarm System :Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 10 Zone 184 Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. 185 Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. 186 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. 187 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. 188 Terrace Pump Set : Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-"F" insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head 189 Pipe 80 mm dia 190 100 mm dia 191 Single headed Stainless steel 192 Supplying & fixing single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed Stainless steel 193 80 mm dia 194 100 mm dia 195 100 mm dia 196 Supplying and fixing Orifice Plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. 197 80 mm dia 198 100 mm dia 199 Stainless Steel (Grade 304) 200 40 m 201 Stainless Steel (Grade 304) 202 2 way - 100 mm dia M.S. Pipe 203 Providing and fixing of pressure switch in M.S pipe line incl connection etc required 204 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 35 sq. mm (35mm) 205 Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure withcover platehavinglockingarrangementand watering pipe of 2.7 RM long etc, with charcoal/ coke and salt as required. 206 Supplying and laying 25 mm x 5 mm.G.I. strip at 0.50 RM belowground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 207 Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. 100 mm dia 208 Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 209 Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 210 1500x900 mm (Indoor Cabinet) Only Frame 211 Providing & fixing cast iron Air Release Valve of 25 mm dia including 25 mm dia Ball valve with fittings etc. as per the requirement. 212 Providing and Fixing of Self illuminated /Auto Glow Exit Signs printed on photo-luminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site. 213 Providing & fixing carbon steel Fire Man Axe with rubber insulated handle tested to 20000 volts. 214 Providing & fixing dial type (150 mm dia) Pressure Gauge with isolation ball valve suitable for working pressure of 250 PSI cost shall be of inclusive of providing any short pieces, nipples, elbows etc as required.having calibration of0-15 Kg/cm2. 215 100 mm dia 216 Control Panel (for Terrace Pumps) : 63 Amp, 25kA TPN MCCB, Ics=100% Icu, with Suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. - 1 Se 217 Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.35 sq. mm 3-1/2 core 218 Supply and fixing of LIFT 8 passangers capacity including all accssories incl labour and T&P Etc required. Type of Lifts : S.S. hairline finish & Mirror Finish Cabin, Center Opening Automatic Door, Passenger Lift.Capacity / Load : 8P / 544 Kgs.Speed : 1 mtr/sec (60 mtr/Min).Operation : Luminous Push button full Collective, selective & simplex.Control : Open Loop Down Collective Microprocessor based ontroller.Cabin : S.S. hairline finish & Mirror Finish Laser Cut & Sheet Metal Press Bent Panel.Cabin Car Door : 1 nos. S.S. hairline finish center opening Automatic Door powered with electrical safety interlock.Landing door : 5 nos. Center Opening Automatic Door powered with electrical & Mechanical safety interlocks.Cabin Size : 13000mm Wide X 1500mm Deep X 2000mm High (almost) S.S. hairline finish & Mirror Finish Cabin, S.S. hairline finish center opening Automatic Door, Passenger Lift 219 Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant 25kWpconforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solarcells, net RMing facility, necessary protections, earthing, mounted on Aluminium/GI structureof suitable strength with following components complete as required:-a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming toIS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Moduleconversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than90% at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, threephase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency notless than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid VoltageFrequency.c) Data Monitoring System complete with accessories.d) Fixing of Array junction box & Main junction box with IP 65 protection and terminationarrangement for incoming and outgoing cable along with glands, lugs and other accessories etc.as required.e) Lightning and surge voltage protection.f) Connections & Interconnections by supplying & fixing required size XLPE insulated copperconductor 1.1 kV grade armoured power and control cables between solar modules, main powercable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs andother accessories etc. as required 220 Supply, Installation,Testing&Commissioning of Layer Access switch 48 port 10/100/1000 with 1 No of 10 G Port 221 Supply, Installation,Testing & Commissioning of Layer switch 24port 10110011000 with 1 No of 10 G Port 222 Supply, Installation,Testing&Commissioningof Layer 2 Access switch 8 port 10/100/1000 with 1 No of 10 G Port 223 Supply, Installation, Testing & Commissioning of Layer 3 Core Switch Cisco Nos 124 Port with 4•10G Fiberports Can 224 Supply, Installation. Testing & Commissioning of Layer 2 POE+ 24port Cisco Nos. 1 265750 265750" switchrequirement for CCTV , VVi-fi 225 Supply, Installation, Testing & Commissioning of UTM for 200 user Supporting 200 MBPS with 3 year support 226 Slimly, Installation, Testing and Commissioning of 10G SFP+ Transceiver for Fiber 227 Supply, installation, Testing & Commissioning of UTP Cat 6 information Legrand Outlet for Data 228 Supply, Installation, Testing & Commissioning of Cat 6Mounting Cords Legrand 4 Feet for Data Jack Panel end 229 Supply, Installation, Testing & Commissioning of Cat 6 Mounting Legrand Nos l43 204 29172Cords 7 Feet for Data 230 Supply, Installation, Testing & Commissioning of Cat-6 48 Port Jack Legrand Panel for data 231 Supply, Installation, Testing & Commissioning of Cat-6 24 Port Jack Legrand Panel for data 232 Supply, Installation, Testing & Commissioning of I port faceplate Legrand with Gang Box etc. all complete.: 233 Supply, Installation, Testing & Commissioning of Cat 6- 305 Mtr. 234 Supply, Installation, Testing & Commissioning of 15 U Wall Mount Rack 235 Supply, Installation, Testing & Commissioning of 40 KVA UPS with Mins Backup 236 Supply, Installation, Testing & Commissioning of 27 U Wall Mount 237 Supply & installation of 25MM PVC Conduit 238 Supply, Installation, Testing 8. Commissioning of 12 Port Fiber LIU Legrand Loaded with 6 SC MM Coupler, 239 Supply, Installation, Testing & Commissioning of 24 Port Fiber LIU Legrand Loaded with 24 SC MM Coupler, 240 Supply, Installation, Testing & Commissioning of SC MM Pigtail Legrand (1.0 Mtr) as per given Specification etc. all complete. 241 Supply, Installation, Testing & Commissioning of SC-LC MM Fiber Patch Cords ( 3 Mtr) 242 Supply, Installation, Testing & Commissioning of 6 Core Multi Mode Fiber Lrii-armored) Cable 243 Supply. Installation, Testing & Commissioning of HOPE Pipe 244 SUB HEAD (I) :- INTERNAL WIRING Wiring for light point / fan point/ exhaust fan point/ call bell point 1.5 sq mm FRLS PCV Insulated copper conductor singhle core cable in surface 245 Twin Control Point wiring in PVC conduit, with piano type switch :- Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, 2 way piano type switch, phenolic laminated sheet, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 246 Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 247 Power plug wiring in PVC conduit (4 x 4 Sq.Mm.) :- Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvcconduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 248 Circuit / Sub main wiring in PVC conduit :-2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire. 249 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. 250 2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire 251 2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire 252 2 x 16sq.mm. + 1 x 6 sq.mm. Earth wire 253 4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire 254 S/F light plug point piano type accessories :- Supplying and fixing metal box of 150 mm X 75 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required. 255 S/F power plug point piano type accessories :- Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required. 256 Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 poles and earth metal enclosedplug top alongwith 20amps. "C" curve, SP MCB in sheet steel enclosure, on surface or in recess, with chainedmetal cover for the socket outlet, and complete with connections, testingandcommissioning etc. as required. 257 Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 258 Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 259 Supply and fixing offollowingsizes of medium class PVC conduit along with accessories in surface/recess including cuttingthe wall and making good the same in case of recessed conduit as required 20 mm. 260 Supply and fixing offollowingsizes of medium class PVC conduit along with accessories in surface/recess including cuttingthe wall and making good the same in case of recessed conduit as required25 mm. 261 Supply and fixing offollowingsizes of medium class PVC conduit along with accessories in surface/recess including cuttingthe wall and making good the same in case of recessed conduit as required32 mm. 262 DISTRIBUTION BOARDS & MCB"s single pole Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C" series,miniature circuit breaker (MCB)suitable for inductive load offollowingpolesin the existingMCBDBcomplete with connections, testing andcommissioning etc. as required. 263 Supplying & fixing single pole, blanking plate in the existing MCBDBcomplete etc. as required. 264 S/F Double pole 240 v isolator in the existing MCB DB Complete testing and commissioning 40 Amps 265 S/F Double pole 240 v isolator in the existing MCB DB Complete testing and commissioning 63 Amps 266 S/F Four pole 415V isolator in the existing MCB DB Complete testing and commissioning 63 amps. 267 S/F Double pole (Single phase and neutral) 240 v RCCB hahing sensitivity current upto 300 m.amp existing MCB DB Complete testing and commissioning 40 amps. 268 S/F Double pole (Single phase and neutral) 240 v RCCB hahing sensitivity current upto 300 m.amp existing MCB DB Complete testing and commissioning63 amps. 269 S/F four pole (Single phase and neutral) 240 v RCCB hahing sensitivity current upto 300 m.amp existing MCB DB Complete testing and commissioning63 amps. 270 S/F SP&N Sheet steel MCB Distribution board 240 V 6 way, Double door 271 S/F SP&N Sheet steel MCB Distribution board 4 way (4 + 12), Double door 272 Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure withcover platehavinglockingarrangementand watering pipe of 2.7 RM long etc, with charcoal/ coke and salt as required. 273 Supplying and laying 25 mm x 5 mm.G.I. strip at 0.50 RM belowground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 274 Providing and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 275 Providing and fixing 25mm x 5 mm G.I strip on surface or in recess for connections etc. as required. 276 Providing and fixing 6 SWG dia G.I. wire onsurfaceorin recessfor loop earthing as required. 277 Providing and fixing M.V. dangernotice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription singleredcolouronFRLSontsideas required. 278 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 279 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 run of cable 280 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections butexcluding modular plate etc. as required. 5/6 A switch 281 3 pin 5/6 A socket outlet 282 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) 283 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. 284 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 285 Supplying and fixing Internet Socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 286 Installation, testing and commissioning of pre-wired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 287 Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 288 Upto 450 mm sweep Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required 289 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 290 Supply of 36 Watt to 46 Wattindoor Recess mountingLED Square Fitting for Armstrong Ceilinghaving Powder coateddie cast aluminium housing body withextended heat sink and diffuser ofSpecial Polycarbonate RMial and driver set complete in all respect. 291 Supply of LED Tube Light with Metal heavy duty Box type batten Light fitting 1X22 watt suitable for upto 1X22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. 292 Supplyof LED Tube Light with Metal heavy duty Box type batten Light fitting 2X22 watt suitable for upto 2X22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. 293 Supply of recess/surface mounting round 10 W to 15 W LED Cut out Min 125 mm, Height Min. 40mm, LED Down lighiter having powder coated die cast aluminium housing with heat shink,diffuser/reflector and driver set. suitable for 24Hr Continuous Operation, Complete in all respect. 294 SUPPLY OF CEILING & EXHAUST FANS Supply of 225/230mm sweep ventilating (Light Duty) exhaust fan complete with Metallic Blade (Steel bird guard protector /Copper motor for high air suction performance /Capacitor etc.), Noise level : (45 - 50) dB, Power consumption : 45 W, Rated voltage : 230 V, Rated frequency : 50 Hz, Motor type : Normal Speed. Complete in all respect. 230 mm sweep 295 Supply, installation, testing and commissioning of electrical panel, modular type, front accessible only, free floor standing confirming to Minimum IP:43 degree of protection.The panel sheet structure shall undergo seven tank pre-treatment process before painting.The sheet steel shall be all of 2.2mm thick CRCA sheet.All the openable compartments of the panel shall be completely shrouded and provided with padlocking arrangement on all compartments including bus bar and cable alley chambers.The panel height shall not exceed 2200mm and the maximum operating height for any switchgear shall not be more than 1700mm.The panel shall be provided with minimum 75mm base channel frame fabricated from ISMC sections.All bus bar links in the panel shall be solid bus bars with coloured PVC shrinkable sleeves, no wires will be acceptable.Continuous earth bus shall run alround the panel with earthing studs provided at minimum 2 places.The control wiring shall be carried out with minimum 1.5/2.5 sqmm copper wires andBus Bar : Phase indication lamps on Nos outgoing to be provided. 40 Amps TPN MCB - 1No. Spare 296 Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.16 sq. mm 4 core 297 35 sq. mm 3-1/2 core 298 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 16 sq. mm 4 core 299 3½ X 35 sq. mm (35mm) 300 Supply of VRV airconditioning system (equipments) comprising of Outdoor Units-VRV-HEAT PUMP ,ODU - 46 H.Pmodel no -RXYQ14ARY6+RXYQ16ARY6+RXYQ16ARY6+BHFP22P1516, Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . (MR) 301 Supply of VRV airconditioning system (equipments) comprising of Outdoor Units-VRV-HEAT PUMP,ODU - 20 H.Pmodel no -RXYQ10ARY6+RXYQ10ARY6+BHFP22P1006,Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . (MR) 302 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsceiling mountedRound flow Cassette Type Unit- 4.13 TR + Corded Remote + Refnet,model no -FXFSQ125,Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . (MR) 303 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsceiling mounted Round flow Cassette Type Unit- 3.31 TR + Corded Remote + Refnet model no -FXFSQ100,Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . (MR) 304 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsceiling mountedRound flow Cassette Type Unit- 4.13 TR + Corded Remote + Refnet model no -FXFSQ125, Work executedas per design/drawing and satandard required and approved brand.proper completion of the work and as per direction of E/I make daikin OR equaelent brand . (MR) 305 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsceiling mounted Round flow Cassette Type Unit- 4.63 TR + Corded Remote + Refnet model no -FXFSQ140, Work executedas per design/drawing and satandard required and approved brand.proper completion of the work and as per direction of E/I make daikin OR equaelent brand .(MR) 306 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories items ceiling mountedRound flow Cassette Type Unit- 2.65 TR + Corded Remote + Refnet, model no -FXFSQ80. Work executedas per design/drawing and satandard required and approved brand.proper completion of the work and as per direction of E/I make daikin OR equaelent brand (MR) 307 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsHi Wall Type Unit- 1.06 TR + Corded Remote + Refnet, model no -FXAQ32,Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . 308 Supply of VRV airconditioning system (equipments) comprising of Indoor Units & Accessories itemsHi Wall Type Unit- 1.32 TR + Corded Remote + Refnet, model no -FXAQ40,Work executedas per design/drawing/satandard and specificationrequired and approved brand.proper completion of the work and as per direction of E/I make daikin OR Equivalent brand . (MR) 309 Supply, Installation, Testing, and Commissioning of Premium branded Multimedia Projector, 3200 lumens, 15000:1 contrast Ratio, XGA resolution.including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 310 Supply, Installation, Testing, and Commissioning of Premium branded Projector Ceiling Mount Kit including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 311 Supply, Installation, Testing, and Commissioning of Premium branded 8’x6’ Self Lock Projection screenincluding material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 312 Supply, Installation, Testing, and Commissioning of Premium branded Two way Wall speaker 70v,100v, 30 watt. including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge 313 Supply, Installation, Testing, and Commissioning of Premium branded Power amplifier 4 inputs, 1 aux, Multiple outputs - 70 V / 100 V and 8/4 ohm Temperature controlled forced front to back ventilation, directly stackable 120 wattincluding material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge 314 Supply, Installation, Testing, and Commissioning of Premium branded Wireless Gooseneck microphone set of four microphone with receiverincluding material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 315 Supply, Installation, Testing, and Commissioning of Premium branded Supporting Cables & connector, VGA Cable, Power Cable, speaker Cable, Stereo Cable, VGA and aux connector Plate including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 316 Supply, Installation, of Premium branded Equipment Rack of standard size as per requirement including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 317 Supply, Installation, Testing, and Commissioning of Premium branded laptop including material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 318 Supply, Installation, Testing, and Commissioning of Premium branded UPS with battery backupincluding material, labour, T&P etc. required for proper completion of work as per the direction of engineer in charge. 319 Supply, Installation, OF WATER COOLER
|
