|
Tender For Additional / Alternator To Married Quarters At Af Stn Jamnagar; 2 Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 Sqm each, complete all as specified and directed. 3 Taking down chowkhat or frame with shutter(without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed. 4 Taking down shutters of any description exc 1 Sqm but n.exc. 2 Sqm each complete complete all as specified and directed. 5 Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to outside MOD land complete all as specified and directed. 6 Demolition of cement concrete in ground floor and pavings not exc 15 cm thickness below or above ground level, including removal of debries to outside MOD land complete all as specified and directed. 7 Demolition of brick / stone / PCC block masonry built in cement mortar including all quoins, pillars, arches etc. including removal of debries out side MD land, complete all as specified and directed. 8 Demolition of reinforced cement concrete of any description and in any position and( reinforcement not cut in chajja/finsto facilitate demolition) including removal of debries to outside MOD land complete all as specified and directed. 9 Demolition and breaking up drain pipes 100 mm dia (SGSW, AC or RCC hume pipe Class NP2 laid in trenches and jointed in cement mortarcomplete all as specified and directed. 10 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. and brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified and directed. 11 M&L 20-25mm thick machine cut kota stone slab flooring, treads etc over and including laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 12 M & L for RCC 1:1.5:3 (Nominal mix) type A1 using 20mm graded aggregates as in Chajjas,andthe like complete all as specified anddirected. 13 M & L for mild steel TMT CRSbars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and bindersand binding with and including mild steel wire annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed 14 M & L for mild steel TMT CRS bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified anddirected 15 M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges flat fair finished surfaces of concrete complete all as specified anddirected . 16 M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n.exc 10cm wide complete all as specified anddirected . 17 M&L for 75 mm thick plain cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate as in plinth protection surfaces finished even and smooth without using extra cement complete all as specified and directed. 18 M& Lfor forming 6 mm wide and 10 mm deep joints in PCC and joints filed with bituminious mastic (1 part of bitumen and 2 part of sand )in plinth protection complete all as specified and directed. 19 M&L for Pre-cast cementconcrete block of 1:3:6 type C1 (20mm graded aggregate)blockmasonry with solid blocks, exc. 10 cm in width and built in cement mortar 1:6 complete all as specified and directed. 20 M&L for Providingprecast cement concrete 1:3:6 type C1 (20mm graded aggregate)solid building blocks or slabs 10cm thick (with plain or interlocking jointsasdirected) setting in mortar, complete, in walls in half brick thickwalls built in cm 1:4 complete all as specified and directed. 21 S&F GI Pressed steel powder coated door frame single rebate 105 x 60x 1.6mm with ball bearing,03 x Nos S/S304 Hinges,06 x Nos Holdfast 200mm x 40mm x 2mm welded to frame ,02 x Nos GI angle tie 20x20x1.60mm and hinges screwed with flat iron 30 x 6 x 120mm long mortar guards and filled with PCCcomplete all as specified and directed. 22 S&F GI Pressed steel powder coated door frame double rebate 125 x 60x 1.6mm with ball bearing,03 x Nos S/S304 Hinges,06 x Nos Holdfast 200mm x 40mm x 2mm welded to frame ,02 x Nos GI angle tie 20x20x1.60mm and hinges screwed with flat iron 30 x 6 x 120mm long mortar guards and filled with PCCcomplete all as specified and directed. 23 S&F Factory made solid UPVC wardrobe with frame profile size 71mm x 45mm with MS stiffner and rubber gasket shall be fixed to wall as per manufacturing instructions and UPVC solid shutters with 6mm thick high pressure compact laminate sheet fixing horizontal & verticle style size 71mm x 28mm thickand MS pipe frame as stiffener size 39mm x 18mm x 1mmwith rubber gasket and UPVC solidoverlap "L" profile size 16mm x 08mmincluding all necessary stainless steel hardware fittings (Handles, Self closing hinges, lock, Magnetic catcher )complete all as specified and directed as per Drg No CEAG/AR/TD/09R sheet of 01/03 to 03/03. 24 S&F Factory made solid UPVC Kitchen cabinet carecase is made of 35mm thick sandwich panel using UPVC profile 35mmx25mm thick incl shelves and 3mm thick high pressure complete laminate (Phenol formaldehyde bonded) sheet on both sides and EPS insulation in between as well as MS pipe frame as stiffener. Front to cabinetshutter is made of UPVC profile 45mmx20mm and 3mm thick high pressure compact laminate (phenol formaldehyde bonded) sheet incl all necessary stainless steel hardware fittings (handles, self closing hinges & magnetic catcher) complete all as specified and directed as per Drg No CEAG/AR/TD/11R sheet of 01/04 to 04/04. 25 S&F Factory made solid UPVC Kitchen cabinet below cocking platform is made with UPVC solid frame of size 45mm x 20mm shall be fixed to wall as per manufacturing instructions and UPVC solid shutters with 6mm thick high pressure compact laminate sheet fixing horizontal & verticle style size 45mm x 20mm thick including all necessary fittings (Handles, Self closing hinges, Magnetic catcher )complete all as specified and directed as perDrg No CEAG/AR/TD/11R sheet of 01/04 to 04/04. 26 S&F Factory made solid UPVC Kitchen shelves made of 35mm thick with profile 35mmx17mm thick and 03mm thick highpressure compact laminate sheet on both sides and EPS insulation in between as well as MS pipe frame as stiffener including all necessary fittings complete all specified and and Drg No CEAG/AR/TD/11R sheet of 01/04 to 04/04. 27 M&L for factory made flush shutters,35mm thicksolid core construction, with block board core and plywood face panels, commercial type on both sides with 12mm thick teak wood lipping/beading all around including0.90mm thick decorative laminate type 1 on both sides,of surface finish, colour as approved, fixed with approved adhesive as per manufacturer"s instructions complete all as per specified and directed by Engineer-in-Charge. 28 S&F 35 mm thick factory made second class hardwoodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkhats complete. complete all as specified and directed. 29 S&F Stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples to wooden shutters complete all as specified and directed. 30 Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm havingsingle rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fireresistant grade unsaturated polyester resin and choppedmat. Door frame laminate shall be 2mm thick and shallbe filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides.M.S. stay shall be provided at the bottom to steady theframe., complete as specified and directed. 31 Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand andmanufacture, made with fire - retardant gradeunsaturated polyester resin, moulded to 3 mm thickFRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned woodinside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate forpanels conforming to IS: 14856, including fixing toframes, complete as specified by the manufacturerand as per directions of Engineer- in-charge. 32 S&F SS 304 grade hinge 25x25x100mm long 3mm thick with ball bearingfixed to chowkhat complete all as specified and directed. 33 S&F 200 mm long aluminium anodised barrel tower bolt of extruded sectiion complete all as specified and directed. 34 S&F 150 mm long aluminium anodised barrel tower bolt of extruded sectiion complete all as specified and directed. 35 S&F 150 mm long aluminium handle, fabricatedtype, anodised complete all as specified and directed. 36 S&F 100 mm long aluminium handle, fabricatedtype, anodised complete all as specified and directed. 37 S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. 38 S&F 300 mm, size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed. 39 S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 40 S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete all as specified and directed. 41 S&F powder coated aluminium(minimum thickness of poweder coating 50 micron) for shutters of doors,windows & and ventilators including providing and fixing hinges/pivotes/handle and making provision for fixing of fitting whereever required including the cost of EPDM rubber/neoprene gasket required(fitting shall be paid separately) with extruded built up standered tubular sectios/ appropriate Z section and other sections of approved make conferming to IS 733 and IS : 1285 , fixing with dash fasteners of required dia and size including necessary filling up the gaps at juctions , ie at top , bottom and sides with required EPDMrubber neoprene gasket,concealed type lock for all three shutter, PVC roller etc . Aluminium sectios shall be smooth , rust free , straight , mitred and jointed mechanically wherever required including cleat angle, luminium slap beading for glazing/ panelling , C.P. brass stainless steel screws complete all as specified and directed.Note for item No 36 & 37 : (i)Three track aluminium windows : (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50mm (Section No 20831)(b) Frame (bottom) section shall be of size 92.00 x 31.75 x 1.50mm (Section No 20832) (c) Top & Side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock section shall be of size 18.00 x 40.00 x 1.45mm (Section No 20737) (e) Bottom Members of shuttersection shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736). (ii) Ventilators : (a) Frame top,bottom & sides shall be of size 100x50x1.50mm (Section No S4859) (b) Frame for wire mesh shall be of size 50x25x1.00mm (section No 14039).Section No given above are of Make Jindal 42 S&F 5mm figured glass , pin headed type and glazing with oil putty in square n.exc 0.50 m in each pane for windowes/ventlators complete all as specified and directed. 43 M&L for preparation of new wooden surfaces, exc 10 cm width or girthand applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 44 S&F GI powder coatedframed work such as grills gratings etc with ends of bars shouldered and / or riveted or forged into spiked framed guard bars barred iron doors ladders framed blasters walkways railingsframework of water tanks and similar workcomplete all as specified and directed. 45 S&F in repair Stainless steel curtain rods of 25mm dia complete all as specified and directed. 46 S&F SS ornamental stainless steel holding brackets /end cap for 25 mm dia curtain rods complete all as specified and directed. 47 S&F Stainless steel peg set of 5 hooks including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms). 48 Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal of debries to outside MOD land complete all as specified and directed. 49 M &L for plain cement concrete type E-2 (1:5:10), using 40 mm graded stone aggregate, for filling sunken portion of toilet and similar work complete all as specified and directed. 50 M&L for providing water proofing treatment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make as approval in Technical Instruction 5/2003 by adding: (a) 15mm thick rendering CM (1:4) with Liquid water proofing compound 200ml per 50kg bag of cement on floor and wall , finishing the surface even and smooth without using extra cement. The surface shall then be cured and allowedto dry. (Note: Water proofing compound shall be measured and paid separately). (b) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hrs.(c) Second layer of slurryof cement @ 0.242 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs including complete removal of old treatment to sunken portion etc complete all as specified and directed. 51 M&L for Non skid,(Joint Free)coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.11 sqm but not exeeding 0.18 sqm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed. 52 M&L for Non skid,(Joint Free)coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.11 sqm but not exeeding 0.18 sqm as in vertical surface skirting/Dado of walls etc laid overrendering 10 mm thickcement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed. 53 M&L for Non skid, (Joint Free) coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.18 sqm but not exeeding 0.38 sqm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed. 54 M&L forcoloured glazed ceramic(Joint Free)tiles of size 450X 300X 7 mm to 8 mm thick (square / rectangular) thick as in skirting / dado etc laid over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed. 55 M&Lfor green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like set over & incl 15mm thick cement mortar (1:4) including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. (Note :-(a) Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations as directed. 56 M&L for18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in set over & incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. (Note :-(a) Rounding to edges of stone slabs one edge, such as in window jamb and cills, steps, cooking platform, and other similar situations as directed. 57 M&L 20-25mm thick pre polished machine cut kota stone slab flooring, treads etc over and including 15 mm thick screed bed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note :-(a) Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations as directed. (b) Forming grooves for treads, straight or winding as directed 58 M&L 20-25mm thick pre polished machine cut kota stone slab in riser of steps, skirting,dado and pillar laid over and including 10 mm thick plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.Note :-(a) Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations as directed. (b) Forming grooves for treads, straight or winding as directed 59 Rounding to edges of stone slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and directed. 60 S&F in repairs 15mmbore bib taps ,fancy type of cast copper alloy chromium plated withcapstan handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 61 S&F in repair 15mm sizebib tap cast copper alloy chromium plated, with capstan head , screwed down , screwed for iron pipe complete complete all as specified and directed. 62 S&F in repair 15mm bore dia stop valve/angle valve cast copper alloy chromium plated, fancy type screwed down high pressure with capstan handle, screwed both ends for iron pipe or for union complete all as specified and directed. 63 S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position completeall as specified. 64 S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. 65 S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed 66 S&F 15mmcold and hot wall mixer brass chromium plated with bend pipe including all accessories completeas directed by Engineer-in-Charge. 67 S & F in repair 10 Ltr capacity PVC valveless , syphonic action type , flushing cistern low level white with inlet ball valve float and handle including bracket , 32 mm dia pvc flushing pipe complete all as specified and directed. 68 S& F in repairs brass chromium plated overhead shower 125 mm size with 225 mm arm and flange for 15mm inlet pipe complete complete all as specified and directed. 69 S&Fin repair white vitreous china wash hand basin of size550 x 400 mm, fixed over & including GI brackets comprising of the following items :-(a) Waste fitting 32 mm dia chromium plated with long screwed shanks and fly nut, flange end, bedded in red lead cement and other end fixed complete.(b) 15 mm size Pillar tap cast copper alloy with capstan head, chromium plated screwed down high pressure with or withoutlettered hot or cold with long screwed shank and fly nut screwed for iron pipe complete all as specified and directed.(c) 32 mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed. 70 S&F 32mm bore dia light grade GI pipe cocealed in wall or laid in floors complete all as specified. 71 S&F stainless steel kitchen plate rack of size 750mmx600 mmx250mm deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and directed. 72 S&F in repairs 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washerscomplete all as specified and directed 73 S&F sheet glass shelf assembly consisting of 5.5mm thick sheel galss shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 74 S&F stainless steel soap dish of size160x160x1mm thickfixed to plugs with chromium plated brass screws as complete all as specified and directed. 75 S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, with plastic water closet seat, white, closed pattern with flat bottom, and cover with aluminised hinging device, including all connections complete complete all as specified and directed. 76 S&F in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580mm x 440 mm white with integral foot rests icluding 100 mm dia CI "P’ trap or S trap including all connection and provision of lime concrete base complete all as specified and as directed. 77 S&F in repairs brass Chromium platedtubular Towel rail 20 mm dia D type 600mm long bettwen flangefixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. 78 S & F Stainess steel Towel Ring fixed with and including Chromium plated brass screws complete all as specified and directed 79 S&F in repairs stainless steel sink, 1.00 mm thick for kitchen, with plug, washers and wastes coupling, including bedding in cement mortar on to draft wall or including fixing cantilever brackets, connecting union to pipe etc, overall size 495 mm x 420 mm, with bowl size 410 mm x 330 mm x 160 mm, complete complete all as specified and directed. 80 S&F in repair PVC connection 15mm dia and 45 cm long with 2 Nos PTMT nuts,complete all as specified and directed by Engineer in Charge. 81 S&F 100mm cast iron sanitaryconnections—short connections pipeof length upto 300 mmcomplete all as specified and as directed. 82 Taking down CI/rain water pipes/PVC pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, complete all as specified and as directed 83 S & F 75mm dia UPVC (SWR) pipes,Type B, single socketed, in any length with rubber ring joints, fixed in walls/ factory made pipe supporting system as per manufacturer instruction and as directed. Note : Pipe shall be fixed on wall at an over multi pipe bracket system stack clamp at an alternalte interval of 1m(U bolt with noise absorbing transparent ribbed silicon ribber sleeve of 2mm thickness with set of knurling flange nuts+bracket+ support) confirment with outer dia of pipe fixed at intervals of every meter at a specified distance from the wall for vertical and horizontal lines, which are made of deep draw low carbon hot rolled gauge corrected (HRGC) steel (Material grade IS 1079DD), hot dip galvanising (IS 2629)+ ZNAL (Zinc Aluminium flake) coated with ribbed support and all as per drg No CEAG/AR/TD/08R 84 S & F 75mm dia UPVC (SWR) pipes,Type B, single socketed, in any length with rubber ring joints, laid in trenches or in floor completeall as specified and as directed. 85 S & F UPVC SWR 75mm dia bends of any radius complete all as specified and directed 86 S & F UPVC SWR 75mm dia branch piece, single (Single Y) equal or unequal complete all as specified and directed 87 S & F UPVC SWR 75mm dia branch piece, Double(double Y) equal or unequal complete all as specified and directed 88 S & F 110mm dia UPVC (SWR) pipes,Type B, single socketed, in any length with rubber ring joints, fixed in walls/ factory made pipe supporting system as per manufacturer instruction and as directed. Note : Pipe shall be fixed on wall at an over multi pipe bracket system stack clamp at an alternalte interval of 1m(U bolt with noise absorbing transparent ribbed silicon ribber sleeve of 2mm thickness with set of knurling flange nuts+bracket+ support) confirment with outer dia of pipe fixed at intervals of every meter at a specified distance from the wall for vertical and horizontal lines, which are made of deep draw low carbon hot rolled gauge corrected (HRGC) steel (Material grade IS 1079DD), hot dip galvanising (IS 2629)+ ZNAL (Zinc Aluminium flake) coated with ribbed support and all as per drg No CEAG/AR/TD/08R 89 S & F 110mm dia UPVC (SWR) pipes,Type B, single socketed, in any length with rubber ring joints, laid in trenches or in floor completeall as specified and as directed. 90 S & F UPVC SWR 110mm dia bends of any radius complete all as specified and directed 91 S & F UPVC SWR 110mm dia junction single (Single Y) equal or unequal complete all as specified and directed 92 S & F UPVC SWR 75mm dia branch piece, Single(Single Y) equal or unequal complete all as specified and directed 93 S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified and directed 94 S&F UPVC (SWR) vent cowl 110 mm dia complete all as specified and directed 95 S & F 75mm UPVC nahani trap, plain with grating including jointing with solvent cement complete all as specified and directed. 96 S & F 75mm UPVC gullytrap, plain with grating including jointing with solvent cement complete all as specified and directed. 97 S&F in repair Stainless Steel 304 Gratings in square type and ofsize 125mm x 125mm made in two parts for smell and mosquito proofing with double jalicomplete all specified and directed 98 S&F40mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kg/cm2 fixed complete to walls, ceilings or in floors complete all as specified & directed. 99 Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc,including removal of debries out side MoD land complete all as specified and directed. 100 M&L for rendering 15 mm thickin two layers Istlayer 10 mm thick and 2nd layer 5 mm thick,final coat shall be mixed with WPC on brick/stone/ PCC block masonry wall surface in cement mortar 1:4, finished even and smooth withoutusing extra cementcomplete all as specified and directed. Note : Water proofing compound shall be measured and paid for separetly 101 M&L for rendering 15 mm thick on other than fair faces of brick/stone/ PCC block masonry wall surface in cement mortar 1:4, finished even and smooth withoutusing extra cementcomplete all as specified and directed. Note : Water proofing compound shall be measured and paid for separetly 102 M&L for rendering 10mm thick on other than fair faces of brick work or concrete surfaces or stone masonry surfaces in cement mortar 1:6, finished even and smooth withoutusing extra cement complete all as specified and directed. 103 M&L for 5mm thick rendering in cement mortar 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and directed. 104 M&L for preparation ofnew plastered surfaces of walls & applying two coat of Distemper oil emulsion overa coat of primer on wall surfaces applied by mechanical means using suitable tools and plants as per manufacturer"s instructions complete all as specified and directed. 105 M&L for complete removal of existing treatment from wall including brooming down or steel wire brushing, scraping down complete including preparation of old surfaces and applying two coat of Oil bound Distemper over a coat of primer on wall surfaces applied by mechanical means using suitable tools and plants as per manufacturer"s instructions complete all as specified and directed. 106 M&L for preparation of new plastered surface of wall andapplying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces two coats of Acrylic emulsion (exterior weather coat) paint of any tint as approved over one coat of primer applied by mechanical means using suitable tools and plants as per manufacturer"s instructions complete all as specified and directed. 107 M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash applied by mechanical means using suitable tools and plants as per manufacturer"s instructions complete all as specified and directed. 108 M&Lfor preparation of old decorated surfaces of ceiling (plastered or unplastered)by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etcand applying two coat of white wash on ceiling applied by mechanical means using suitable tools and plants as per manufacturer"s instructionscomplete all as specified and directed. 109 M&L complete removal of existing treatment from external surfaces on walls by wire brushes & stopping of surfaces and levelling/edging the disturbedplaces/edges using necessary filling compound of Allek Putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior acrylic emulsion (weather proof treatment) over one coat of primer applied by mechanical means using suitable tools and plants as per manufacturer"s instructions complete all as specified and as directed ( The tint and shade be as approved by the GE) Note:- The treatment shall be carried out by the authorised applicator of the firm. 110 Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-charge. 111 M&L for repairing the edge/corner of chajja/roof projection and similar work by removing of plastered width/girth exceeding 15cm & n.exc 30cm and making good with 15mm rendering in cement mortar 1:3 to match, including chicken wiremesh netting on exisiting surfaces including necessary form work complete all as specified.(Note- Height of building upto 15mtr) 112 M&L for Providing, cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed. 113 M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate,in roof for paddingto achieve therequired slopecomplete all as specified and directed. 114 M&L for 10mm thick rendering on concrete surface in CM 1:3 to be finished even and smooth with out using extra cement mixed with water proofing compound as per manufacturer instructions complete all as specified and directed.Note:-WPC will be measured & paid separately. 115 Material and labour for water proofing treatment by applying one coat of oil base bituminous primer @ 0.3 Kg/Sqm with brush / roller, laying of 3 mm thick APP based polymer modified membrane with non-woven polyester reinforcement/mat (center core), weight not less than 3.50 Kg/Sqm and sealing all the over laps 100 mm in length side and 100 mm in width side of membranes laid with torch application complete complete all as specified and directed.Note : (a) Work shall be carried out upto 2 & 3 storey bldg, contractor to quote rates accordingly.(b) The membrane shall be taken upto height of minimum 300mm through a concrete fillet 75mmx75mm and shall be inserted inside agroove cut in the parapet and fixed. If the height of parapet is 300 mm or less, membrane shall be taken till top of the parapet and finished after covering the top surface of the parapet. For RCC inverted beam, the whole beam shall be covered with membrane irrespective of the depth. In case of roof projection the membrane shall be taken upto the roof edge and sealed by torch application. 116 Supply and provisioning high performance, general purpose, non shrink, cementious repair micro concrete as per manufacturers instructions to an average thickness of 40 to 70 mm for beam and column, fluid micro concrete shall be mixed with 6 mm down coarse stone aggregate and specified quantity of water and fixed using a power including the cost of all materials, rent of tools, scaffolding and labour charges complete all as specified and directed. 117 M&L chipping / dismantling of loose damaged concrete removed carefully by using mechanical concrete upto good parent concrete to expose the existing reinforcement (direct hammering should be avoided) average thickness of chipping average 40 -70 mm alround lintel / beams / column upto 10 mtr height including scffolding complete all as specified and directed 118 Supplying and application of rust remover/converter over the corroded reinforcement bar where ever/Polymer modified mortar micro concreting is required and cleaning the same after application incl cost of all materials, rent of tools, scaffolding, cost of brushes etc. upto 10 mtr heightcomplete all as specified and directed. 119 M & L for grouting of all RCC structure as per manufcature instructions with low viscosity epoxy resin system compising of resin and hardner by using specialized injection instrument injected through nipples including drilling necessary holes of required sizeat distance of approx. between 150mm to 300mm and fixing of PVC Nozzles by quick setting ready made epoxy based plugging putty, scaffolding and pressure of injection may vary from 4 kg/cm2 to 7 kg/cm2 to RCC beams/chajjas/slabs/columns at all heights all as per manufactureres instruction and as directedupto 10 mtr height.NOTES:(i) Payment shall be made as per the weight of epoxy formulation as calculated based on net contained weight of epoxy actually consumed in the work.(ii)The sealed container shall first to be brought to the site and handed over to MES store and thereafter to be used as and when required in the presence of MES executive.(iii)Record of day to day consumption with location and date etc shall be maintained in the serially numbered certified bounded register with shall be signed by contractor and Enggr-in-Charge.(iv) The quoted rate is deemed to include the cost for sealing of cracks required for grouting purpose. 120 Supplying and application of epoxy resinconcrete bonding agent as per manufacturers instructions over the old concrete surfaces including the cost of all materials, rent of tools, scaffolding, cost of paint, brush etc. upto 10 mtr height complete all as specified and directed. 121 M/L for rendering 20 mm thick polymer modified mortarover face of Concrete of column/Beams etc. for height upto 10 mtr in CM mortar 1: 3 along with adding modified styrene butadiene rubber emulsion as per manfactueres instruction and finishing even and smooth. (Modified styrene butadiene rubber emulsion will be measured and Paid seperately) ( Cost of scafflding upto 10 mtr height shall be deemed to be included in the quoted rates) complete all as specified and directed. 122 M&L for providing and injecting chemical emulsion for Post constructional antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed. 123 M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors. 124 S&F 5.5mm thick tinted sheet glass , ordinary quality and glazing with oil putty in square n. exc 0.50 m in each pane for windowes/ventlators complete all as specified and directed. 125 Supply only modified styrene butadiene rubber emulsion complete all as specified and directed. 126 Use & Waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed. 127 Demolition /dismantling of old APP membrane in roof treatment and rubish off premises complete all as specified and directed. . 128 Writing letters or figures (block Roman, Italic or Indian) nexc 30cm high shall be painted thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained complete all as specified and directed 129 Writing letters Stops, commas, short lines, dashes, hyphens, brackets, etc shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained complete all as specified and directed 130 S&F corner glass selfof size 200mm crafted from high quality glass including brass bracket etc. complete all as specified and directed. 131 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete 132 Material & Labour forstainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel brackets,nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. 133 Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete 134 S&F PVC cabinet mirror of size 125mmx450mmx550mmcomplete all as specified. 135 M & L for 100 mm thick cement concrete1:3:6type C2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed. 136 M&L forProviding and laying 60mm thick factorymade chamfered edge cement concrete paverblock of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method usingPU uld, laid in required colour & patternover and including 50mm thick compactedbed of fine sand,mpacting and properembedding/ laying of inter locking paverblocks into the sand bedding layer hrough vibratory compaction by using platevibrator, filling the joints with sand andcutting of paver blocks as per required sizeand pattern, finishing and sweeping extrasand; complete all as specified and directed. 137 M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including all nacessary excavation and earth work in any type of soil and making drainage opening whereverrequired complete all as specified and directed. 138 M&L for PCC (1:3:6) type C2 ,40mm graded aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 150 mm bore for SGWG pipescomplete all as directed by EIC. 139 Material and labour for reinforcement cement concrete pipes, 150mm bore, class NP2, laid and jointed complete with collars all as specified and as directed. 140 M&L PCC (1:2:4) type B1 using 20 mm graded aggregate for coping and as in benching inside the man holes including necessary formworkcomplete all as specified anddirected. 141 M&L for precast cement cocrete cover slabs (1:2:4) type B1 (20mm graded agg) set in CM 1:4complete all as specified anddirected. 142 M&L for PCC (1:3:6) Type C2 using 40 mm graded stone aggregate as in foundation, filling and mass concretecomplete all as specified and directed. 143 M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped endscomplete all as directed by EIC. 144 M&L PCC (1:2:4) type B0 using 12.5 mm graded aggregate for copingincluding necessary formworkcomplete all as specified anddirected. 145 Material and labour for reinforcement cement concrete pipes, 450mm bore, class NP2, laid and jointed complete with collars all as specified and as directed. 146 Excavation in trenches, nexc 1.5m wide and nexc 1.5m deep and getting out in hard/dense soil complete all as specified and directed 147 Returningfilling including spreading, levelling, watering and well ramming in layers not exc 25 cm thick soft & loose soil complete all as specified and directed 148 Removing excavated material (exc1.50Km and n exc 5.00Km) outside defence land and depositingat a level n exc 1.5 m above the starting pointcomplete all as specified anddirected. 149 HOT WATER SUPPLY , INTERNAL & ENTERNAL WATER SUPPLY WORKS (B/R & E/M) 150 Taking up or down 15 mm bore steel tubing and connections, complete all as specified and as directed 151 Taking up or down 20 mm bore steel tubing and connections, complete all as specified and as directed 152 Taking up or down 25 mm bore steel tubing and connections, complete all as specified and as directed 153 Taking up or down 40 mm bore steel tubing and connections, complete all as specified and as directed 154 M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete. 155 Supply and fixing 15mm bore galvanised steel water tubing, medium grade including necessary fittingssuch as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe linecomplete all as specified and directed. 156 Supply and fixing 20 mm bore galvanised steel water tubing, medium grade including necessary fittingssuch as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe linecomplete all as specified and directed. 157 Supply and fixing 25 mm bore galvanised steel water tubing, medium grade including necessary fittingssuch as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe linecomplete all as specified and directed. 158 Supply and fixing 40 mm bore galvanised steel water tubing, medium grade including necessary fittingssuch as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe linecomplete all as specified and directed. 159 S&F CPVC 20 mm pipe for water heater outgoing , ISI Marked conforming to IS 1239 Part-I 2004, 20 mm bore with and including all fittings such as bends , elbows, tees, short length , socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed. 160 Supply and fixing of 20mm dia Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 161 Supply and fixing of 25mm dia Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 162 Supply and fixing of 40mm dia Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 163 Dismantling water tanksof capacity exc 250 and not exc 500 litres removal to store complete all as specified and directed. 164 Supply and fix 500 litres capacity triple layer (white), rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc. complete all as specified and directed. 165 S&F ballvalves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule and fixed 20mm dia complete all as specified and directed. 166 Supply only solar glass tube suitable for glass tube collector of 58mm dia and 1800mm long complete all as specified and directed 167 Supply only solar glass tube suitable for glass tube collector of 48mm dia and 1800mm long complete all as specified and directed 168 Supply and Fixed in Repairs Hot water tank suitable for 100LPD tube collector complete all as specified and directed 169 Taking downand refixing of cold water tank installed for solar water heating system,dismantaling of incoming and outgoing pipe connection ,removal of outgoing pipe line any size and type from cold water tank to solar heating system ,dismantaling of gate valves in outgoing pipe and Refix itto another desired location complete all as specified anddirected. 170 Taking downand removal of hot water tank , solar water heating system ETC type,dismantaling of incoming and outgoing pipe connection ,dismantling of pipe line any sizeand type from solar heating system to hot water tank and hot water tank to gate valve,dismantling of gate valves in outgoing/incoming,certain other accessories connected to solar water heating systemcomplete all as specified and as directed. 171 Taking down and Refixing of steel structure associated with solar water heating systemcomplete all as specified and as directed. 172 M & L for reassembling of solar water heating sysyem ETC type any capacity complete with cold water tank,hot water tank,steel structure ,outgoing pipe from cold waterto solarsystem,pipe line from solar sysytem to hot water tank along gate valve,NRV and other accessories,pipe line from hot water tank till gate valve and,certain other accessories connected to solar water heating systemcomplete all as specified and as directed. NOTE:-Any material damage during dismantaling shall be replaced and paid under respective items. 173 Supply and fix solarwater heater element 2000 W with thermostat cut off electric water geyser temperature controlling sensorsuitable for 230 V ac complete all as specified and as directed 174 M & L for distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 4 way with 100 Amps rated copper busbar, neutral bar, earth bar and cable ties for cable management, reversible door for IP 43 & IP 54, single pole and neutral 250 Volts, flush to wall complete with IP 54 protection complete all as specified and directed. 175 M&L for MCB single pole & neutral240 volt C curve 10 KA (32 to63)Amps capacity IP 20complete all as specified and directed. 176 M&L Sub main wiring using PVC insulated and unsheathed multi stranded FRLS copper conductorcable using approved colour code as per IS drawing in and incl PVC casing and capping of suitable size with all accessories and making good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete asspecified and as directed of the following sizes of cables.(a) Using two single corePVC insulatedFRLS cable 4 sqmm copper conductor multi stranded and 4.0 sqmm copper conductor insulated cable using as earth wireNote :2 runs of 4sqmm copper cable & 1 run of 2.5sqmm copper cable and one run of casing & caping shall be measured as one unit 177 HOT WATER SUPPLY 178 Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point ,socket point or power point includingfixture and fitting such as switches , ceiling roses, pendants , regulators , sockets , light fitting etc. removing material to store for keeping in safe custody or for taking credit( credit for above items should be made asper conditions seperately) and making good the disturbed surfaces of wall/floor or ceiling to match with existing surfaceand finishing the surfaces with distemper/white washing/colour washing as per existingcomplete all as specified and directed. 179 Taking down carefully by unscrewing from main switch boards/cut out boxes/MCB DBs / complete sealing the cable end and making good disturbed surface by walls etc complete all as specified and directed. 180 Taking down carefully by unscrewing from fitting and fixtures such as ceiling fittings,bulk head fittings, tube light fittings ,building street light , floodLED lights etc all as specified and directed. 181 M&L for point wiring with 1.5 Sqmm, multi-stranded copper conductor single core, FRLSH, PVC insulated and unsheathed cable for phase and neutral, including 1.5 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly, drawn in surface/concealed conduit heavy duty (HMS Grade), GI terminal boxes not less than 1.0mm thick fixed flush to wall surface, covered with & including 3 mm thick plastic laminated sheet top cover or including modular plates of required size for mounting switch and sockets etc. complete all as specified and directed for following : -Note : Quoted rates deems to be included cost of modular plate for mounting switches, sockets & regulators as required at site. 182 One light / fan point controlled by one switch one way. 183 One 3 pin 5 Amp switch & socket outlet on same board with other switches. 184 One 3 pin 5 Amp switch & socket outlet on Independant board. 185 One bell point controlled by one switch 5 Amps bell push. 186 One light point controlled by two Nos 5 Amps switch two way 187 All same as per item ser No 178 here-in-above but wiring using 2.5 sqmm multi-stranded copper conductor, single core, FRLSH, PVC insulated and unsheathed cable, including 2.5 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly for 6 pin, 15/16 Amps socket outlet on independant board complete all as specified and directed. 188 All same as per item ser No 178 here-in-above but wiring using 4.0 sqmm multi-stranded copper conductor, single core, FRLSH,PVC insulated and unsheathed cable, including 4.0 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly for two pin earth metal clad plug & socket point for AC/Geysers complete all as specified and directed. 189 S&F Ceiling rose surface bakelite 65x50mm three terminal complete all as specified and directed 190 S&F switch modular single pole one way 6 Amps 230 volt 1 module complete all as specified and directed 191 S&F switch modular single pole two way 6 Amps 230 volt 1 module complete all as specified and directed 192 S&F Socket modular 6 Amp 2/3 pin combined two module complete all as specified and directed 193 S&F switch modular single pole one way 16 Amps 230 volt 1 module complete all as specified and directed 194 S&F Socket modular 6&16 Amp 2/3 pin combined two module complete all as specified and directed 195 S&F Bell Push modular single pole one way 6 Amps 230 volt 1 module complete all as specified and directed 196 S & F Single pole and neutral enclosure with a two pin and earth metal plug and socket complete with one single pole MCB of 5 to 30 amp,240 volt B Curve 20KA,IP 20 complete all asspecified and as directed 197 Supply and fix of Bell musical type AC 230 Volts, as directed including connecting complete all asspecified and as directed. 198 S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx.) with all accessories, fixing arrangement internally pre-wired,fixed in position & connecting complete all as specified and directed. 199 S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 10 watt, channel housing & diffuser of length 600 mm (approx.) with all accessories, fixing arrangement internally pre-wired,fixed in position & connecting complete all as specified and directed 200 S & F bulkhead fitting 10watt made die cast aluminium housing with complete assembly and PC opal diffuser suitable for surface/wall mounted dust and water resistant complete all as specified and as directed . 201 Taking down carefully (copper/aluminium ) submain wiring complete of any type (batten/surface conduit or concealed ) for socket point or power point complete with all fittings such as swiches sockets pendants etc complete and making good distuebed surface of wall,floor or ceiling with plaster of tiles or roof treatment etc and finishing the surface with distemper white washing/colour washing to match with the existing surface complete all as specified and directed 202 M&L Sub main wiring usingPVC insulated and unsheathed multistranded FRLS copper conductorcable using approved colour code as per IS drawing in and incl 20mm PVC conduit with all accessories and making good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete asspecified and directed of following sizes of cables. 203 Using two single corePVC insulatedFRLS cable 6 sqmm copper conductor multi stranded and 6.0 sqmm copper conductor insulated cable using as earth wire complete asspecified and directed Note : 2 runs of 6 sqmm copper cable & 1 run of 6.0sqmm copper cable in and including 32 mm PVC conduit shall be measured as one unit 204 Using two single corePVC insulatedFRLS cable 4 sqmm copper conductor multi stranded and 4.0 sqmm copper conductor insulated cable using as earth wire complete asspecified and directedNote : 2 runs of 4sqmm copper cable & 1 run of 4.0sqmm copper cable in and including 20mm PVC conduit shall be measured as one unit 205 M & L for distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 12 way with 100 Amps rated copper busbar, neutral bar, earth bar and cable ties for cable management,reversible door for for IP 43 & IP 54, single pole and neutral 250 Volts, flush to wall complete with IP 54 protection , with blanker if any mcb slot remain emptycomplete all as specified and directed. 206 M & L for distribution board (DB), double door type, as per IEC 61439-3 made out of sheet metal enclosure (CRCA sheet) dust and vermin proof MCB DB, TPN 4 way with 150 Amps rated copper busbar, 415 Volts with in built TPN MCB 100 Amps, 10 KA, 01 ,new MCB SPN 32 Amp, 10KA -06Nos, IP 54 protection,,reversible door for IP 43 & IP 54 ,flush mounted to wall complete all as specified and directed. Note : Rates are inclusive for flush(Concealed ) mounted of DB, TPN ,MCB SPN 32Amp and 63Amp / Schnieder (Multi-9). 207 M&L for RCCB for earth leakage protection double pole ,30ma for 240 volt25 amp capacity IP 20complete all as specified and directed 208 M&L for MCB single pole & neutral240 volt C curve 10 KA (upto 32)Amps capacity IP 20complete all as specified and directed 209 M&L for MCB single pole,5 to 30 Amp 240 volt B curve 10 KA, IP 20complete all as specified and directed 210 S&Fbuilding security LED Light fitting 35 watt, system efficiency not less than 100 lumen / watt, IP66 protection,consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws,fixed on existing bracket & connecting including taking down old light fitting of any description complete all as specified and directed. 211 Material and Labour for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire mm as 4.0mm dia bymeans of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electricalplate no.3 includingearth pit in PCC concrete 1:2:4 type B-1,Cast iron cover 10 MM THICK HINGED to CI frame ,excavation and earth work in any type of soil and including protectionpipe 15mm dia and water pipe GI tubing 20mmlight grade with funnel and wire mesh connected to earthing test point complete all as specified and directed Note:(i)Rates are inclusive of 7.5m long GI earth wire 4.0mm dia (ii)Rates of CI frame,RCC Pit cover,funnel and wire mesh included in the cost of item. 212 S & F Exhaust fan 300 mm sweep, copper wounded, four blade, metal body, BEE approved/ISI marked, air delivery shall not be less than 230 CFM, mounted in suitable opening arrangement with louvers shutters, suitable for operation on 240 volt, single phase, 50 cycle per second, AC supply and connecting up using flexible cord wire 3 core using PVC flexible conduit from ceiling rose or connector to fan to cover PVC cable including marking of MES number and fixed in position as recommended by manufacturer, including taking down old unsv Exahaust fans and deposited to store yard of E/M section at AF-IIcomplete all as specified and directed. 213 S & F Exhaust fan 250 mm sweep, copper wounded, four blade, plastic body , BEE approved/ISI marked, air delivery shall not be less than 230 CFM, mounted in suitable opening arrangement with louvers shutters, suitable for operation on 240 volt, single phase, 50 cycle per second, AC supply and connecting up using flexible cord wire 3 core using PVC flexible conduit from ceiling rose or connector to fan to cover PVC cable including marking of MES number and fixed in position as recommended by manufacturer complete all as specified and directed.(Note: Rate quoted for above shall be inclusive for making of hole of suitable dia for fixing of exhaust fan in stone masonary bldg/ aluminium window ) 214 M & L for taking down Ceiling fan of any size and its connection & other accessories connected to ceiling fandeposited to store yard of E/M section at AF-II complete all as specified and as directed. 215 S & F Energy efficient BLDC Ceiling Fan, 1200mm sweep BEE 5 star rated, AC single phase, 230 volts, 50 Hz,with remote control regulator and connecting up including provision of three core flexible copper wire of size 1.5 sqmm from ceiling rose to ceiling fan complete in all respectand all accessories complete all as specified and directed. 216 Supply & Fixing 5 star rated electric storage water heater (vertical type) 25 Ltr, 230 V, AC, Single phase power input 2000w, standing loss in kWh 24 (hours) 45°C 0.511 KW h with and including connecting fastners nuts not less than 100 mm with suitable nut, bolt & washers grouted in walls with complete masonary work for proper mounting of Geyser fastning bolts etc as directed as site reqmt and making necessary inlet and outlet water connection brass chromium plated connection pieces with brass hexagonal adopters and washer at both side, suitable for 15 mm dia pipe and 450 mm long.of size 600mm as well aselectric connection including testing on load, including taking down old unsv Gyser and deposited to store yard of E/M section at AF-IIcomplete all as specified and directed. 217 NOTE : Amount of credit of Rs 7,67,711.28 for retrieved material is mentioned in SCHEDULE OF CREDIT on Srl Page No 30 & 31 of tender documents in pdf form which will be deducted offline while acceptance of tender.
|
