|
Tender ForAgriculture Implements (Item Code - M-28) Annual Rate Contract For The Supply Of Agriculture Implements. , Plough Bhangrotu Type (Soil Each Stirring) Conforming To The Designing Or Equivalent Of Agricultural Engineer H.P.Department Of Agriculture, H.P.Model 1986. Net Weightwith Flat Handle-8.000 Kg. +-2% Variation. Detailed Specification For Item Code No. M-2801001001. 1) Main Body Of The Plough: The Body Of The Plough Made Of 5Mm Thick Sheet & Its Length Should Be 28 Cms. & Height 215Mm. Duly Rivetted With One Landside Of M.S. Angle 35X35x6mm Of 200Mm. Length Supported With Two Supports For Blade And Board Made Of M.S. Angles 35X35x5mm, Rivetted With Main Body Of The Plough. 2) Standard:- Onestandard Made Of M.S. Flat Of 35X10mmin290mm. Lengthshouldberevitted With Main Body Of The Plough. The Holes Should Be Made For U Clamp. 3) U Clamp: A U Clamp Made Of M.S. Round 12Mm In 30Cms Length, Bothendsbe Threaded And Two Nuts Of12mmprovided With Both Ends Of U Clamp. 4) Stay Strip:- A Stay Strip Made Of M.S. Flat 25X5mm In 200Mm Length Be Provided With Four Holes Adjusting The Length Beam. 5) Board: Theboard Made Of 5Mm Thick Sheet Slighty Covered In The Centre. The Width Of The Board At Top Should Be 20Cms14cms.In Lower Portion. The Boardshould Be Boltedwithcounter Sunk Bolts And Nut With Supports Rivitedwith Main Body Of The Plough. Thelengthof The Board From The Centre Be 17 Cms. 6) Blade: The Blade Should Be Made Of High Carbon Sheet Or Rail Of 6Mm Thickness And In Triangular In Shape. The Upper Portionofthe Blade Should Be 14Cms. Inwidthand 26Cms. In Length. The Blade Should Be Bolted Withtwo Counter-Sunkboltsand Nuts Withsupportsrevitted With Main Body Of The Plough. 7) Handle: The Handle Made Of M.S.Flat 35X8mm In 850M In Length, Providedwithone Hole In The Lower Portionofthe Handlesoas To Fix The Handle Land-Sideandupper Portion Be Provided With One Conduit Pipe Grip Of 32Mm Diaof1.6Mm Thick And In 15Cms. Length., One Ring Should Be Provided With Handle.Total Weight Of S.S. Plough With Handleapproximately 8 Kgs. (Main Plough 6 Kgs. Andhandle2kgs.)With Variation Of +-2%. , S.Splough (Soil Stirringplough (Bhangrotu Type) Conforming To The Desgning Of Agricultural Engineer H.P. Department Of Agriculture, H.P. Model 1986. Net Weight With Conduit Pipe Handle-6.70 Kg +-2% Variation. Detailed Specifications Is As Under:- 1. Standard:- The Standard (Main Body On Which Share Bladeandboard Are Fixed) Should Be Ofmild Steel Flat Of The Size Of 450X50x10mm Curved At Lower End, To Fix The Share Blade And Board On It. 2. Board:- The Board Should Be Made Of M.S. Sheet 6Mm Thick Slightly Curved At The Centre/Middle. Width Of The Board At The Top And Lower Portion Should Be 210Mm And140mmrespectively. The Length Of Board At The Centre Should Not Be Less Than 150Mm. 3. Share Blade:- The Blade Should Be Made Of High Carbon Steel (0.90% Carbon) Or Rolled Railwayline. It Should Betriangular In Shape With Base Width Of 140Mm, Length At The Centre Should Be 260Mm And Thickness 6Mm. 4. Land Side:- The Land Side Should Be Made Of M.S. Angle 37 X 37 X 5Mm Having Length Of 255Mm. 5. Saddles:- Two Saddles Having Sizes 120X75x6mm And 120X30 X 5Mm Respectively Should Be Made Of M.S. Flat And Welded On The Standard With 4Mmelectrodes. The Share Blade And Board Should Be Fixed On The Standard By Means Of Counter Sunk Bolts And Nuts, 2 Nos. Each On The Welded Saddles. 6. Stay Strip:- A Stay Strip Made Of M.S. Flat 30X5mm In 255Mm Length, Should Have Four Holes To Link The Standard And Handle, Thereby Helpingin Adjusting The Length Of Beam. 7. U-Clamps:- A U-Clamp Made Of M.S. Rounds 12Mm Dia Having 255Mm Length, Both Ends Be Threaded And Two Nuts Of 12Mm Provided With Both Ends Of U-Clamp. 8.Handles:- I) M.S. Conduit Pipe Handle:- Handle Should Be Made Of M.S.Conduit Pipe Having Length One Meter & Dia32mm Of16guage (1.63 Thick). The Upper Portionof150mm Should Be Bent For Gripping The Handle. Lower Portion Should Be Pressed And Welded To M.S. Flat 60 X30 X 5Mm. The Handle Should Be Fixed On The Landside At Rear Endby Means Of Hexagonal Bolt 25 X 8Mm, Five Nos, Of Holes Of 12Mm Dia For Fixing And Adjusting The Heightof Beam Be Provided At A Height Of 170Mm From Bottom End. The Distance From Centre To Centre Of The Holes Should Be 25Mm. Weights Of Each Components Of Bhangrotu Type S.S.Plough Conforming To The Designing Of The Agricultural Engineer, H.P. Bhangrotu, Distt. Mandi And As Per Specification:- Sr.No. Name Of The Component. Gross Standard Weight. 1. Standard-1.755 Kg.; 2. Board - 1.232 Kg.; 3. Share Blade -0.900 Kg.; 4. Land Side - 0.885 Kg.; 5. Saddles First - 0.341 Kg.,Second0.145 Kg.; 6. Stay Strip -0.300 Kg. ; 7. U-Clamp - 0.227 Kg.; 8. Nuts & Bolts - 0.265 Kg. Gross Weight Of S.S.Plough Without Handle 6.050 Kg. Wastage Due To Holes Cuts & Grinding Of Edges And Sides Of Each Component To Give Final Finishes+-= 0.300 Kg. Net Weight With Variation Of + - 2% = 5.750 Kg; 9. Weight Of M.S.Conduit Pipe Handle = 1.000 Kg , S.Sploughlight Duty, Net Weight With Conduit Pipe Handle-4.750 Kgs+ - 2.5% Variation. Detailed Specification Are As Under:-1. Standard:- The Specification ( Main Body On Which Share Blade And Board Are Fixed Should Be Of Mind Steel Flat Of Size 450*50*6Mm, Curved At Lower End To Fix Share Blade And Board On It.. 2. Board:- The Board Should Be Made Of M.S. Sheet Of 3.Mm Thick, Slightly Curved At The Centre/Middle. With Of Board At Top & Lower Portion Should Be 190Mm And 120Mm Respectively. Lenght Of The Board At The Centre Should Not Be Less Than 130Mm.3. Share Blade:- The Blade Should Be Made Of High Carbon Steel Or Rolled Railway Line. It Should Be Triangular In Shape With Base Width Of 120Mm, Length At The Centre Should Be 2500Mm And Thickness 6Mm.4. Land Side:- Land Side Should Be Made Of M.S Angle 35*35*5Mm Having Of 255Mm. 5. Saddles:- Two Saddless Having Size Of 120*75*5Mm And 120*25*5Mm. Respectively Should Be Made Of M.S Flat And Welded On Standard. The Share Blade And Board Should Be Fixed On Standard By Counter Sunk Bolts And Nuts, Two Nos. Each O Welded Saddles. 6. Stay Strip:- A Stay Strip Made Of M.S. Flat 25*5Mm And 255Mm Length, Should Have Four Holes To Link The Standard & Handle, Therby Helping In Adjusting The Length Of Beam. 7. U Clamp:- A U-Clamp Made Of M.S Round Of 12Mm Dia Having 255Mm Length, Both Ends Be Threaded & Two Nuts Of 12Mm Provided With Both Ends Of U-Clamp. 8. M.S Conduit Pipe Handle:- Handle Should Be Made Of M. S Conduit Pipe Having Length One Meter & Dia 32Mm Of 16Swg (1.63Mm Thick). The Upper Portion Of 150Mm Should Be Bent For Gripping The Handle. The Lower Portion Should Be Pressed & Welded To M.S Flat 60*30*5Mm, The Handle Should Be Fixed On The Land Side At Rear End By Means Of Hexagonal Bolt 25*8Mm, Five Nos. Of Holes Of 12Mm Dia For Fixing & Adjusting The Height Of Beam Be Provided At A Height Of 170Mm From Bottom End. The Distance From Centre To Centre Of The Holes Should Be 25Mm. Weight Of Plough With 4.750 Kgs +_2.5% All Dimensions Subject To Variation Of +_ 2.5% , "Plough Shares For Soil Sterring Plough Model-1986, Deptt. Of Agriculture, H.P. Conforming To Is:6327-1971, With Proper Hole, Size Weight Strictly As Per Share Already Fitted With Plough" , Cycle Plough 1. Length Of The Handle 1370Mm. A Pipe Of 25 Od (Over Dia) 25Mmwith Plastic Grip 125 Mm Long And Dual Pipe Distance 300Mm. There Should Be A Sufficient Curve In The Pipe Which Is Connected To The Joint Of The Base Frame. 2. Base Frame ( Flat Size 40X5mm). 460Mm Long. Half Cutted 10Mm Capsule Hole Is Required For Adjusting The Wheel. 3. The Plough Attached With Base Frame Should Be Of Solid Pipe Having Length 270X25mm. For Reversible Action, Plough And Rake Should Be Welded With Pane. Rake Angle Length Should Be 300Mm, Width 32X32.3 Mm. The Length Of Forged And Arrow Type Spike Should Be 200 Mm And Diameter 10Mm. 4. Base Frame Should Be Riveted In The Bottom And Bolted On The Top. Two Holes Are Required For Adjustment (As Per The Height Of The Person) Of The Dual Pipes With The Help Of Two Flats(Size 255Mm). 5. A Normal Tubeless Tire Of480mm. 6. A V-Shaped Pulling Sling Should Be Welded In The Front For Pulling The Cycle Plough With Rope Etc. The Size Of Pulling Sling Should Be 700Mm Long. 7. Size Of Plough -32X8mm Base Frame, Top Plate(12Gauze Mild Steel )-Top Side 200Mm, Left And Right Side 125Mm, Bottom Side 100Mm. The Triangular Blade Of 100X200 Mm And 4Mm Thick With Two Holes Of 8Mm. , Singlerowbarharrow(Bullock Drawn):- Single Row Bar Harrow (Bullock Drawn) As Per Model-85 Deptt. Of Agriculture,H.P. Main Parts Of Single Row Bar Harrow Are As Under:- 1.Frame:- Frame Should Be Made Of Standard M.S. Angle Iron Of 50X50x6mm Size And 85Cms In Length 9Nos. Square Holes Of 16Mm Spaced At A Distance Of 10Cms From Centre To Centre Be Provided For Fixing Of Pegs On The Top From Flange Of The M.S. Angle Iron. Thefirst And Last Holeshould Be At A Distance Of 2.5Cmsfrom The Respective End. 2.Pegs:- 9 Nos. Pegs Of M.S.Square Of16x16mmsize Shouldbe At A Distance Of 10Cms From The Top Endin Sucha Way That The Angle Of Peg In The Frontshould Be 160Mm Length Of Peg May Be 30Cms Includingthe Uniformly Tapered Portion, At The Top The Peg At Least Ata Length Of 20Mm Should Be Uniformlyturnedand Threaded So As To Fit A Standard Nut Of 12Mm Size With Suitable Spring Washer And Lock Trip. The Lower End Of The Peg Shouldbeuniformly Tapered To A Length Of 8Cms. Necessary Provision May Bemade In The Upper Portion Of The Peg By Welding Piece Of M.S. Round 6Mm Dia So As To Provide Obstruction To The Peg For Not Passing Through The Square Hole At The Time Of Tightening The Nut. 3. Hitching Arrangement:-Front Hitch Portion May Be Made Of M.S. Flat 35 X 6Mm Sizehavingappropriate Curvatureandat Least 4 Nos. Holes Of 10Mmdia Be Provided With A Bolt Of10x8mm (Carriage Bolt) So As To Adjustthebeamto Thedifferentheightsof The Bullocksasper Requirements Ofthefields.Front Hitch Should Be Supported With 2 Nos. M.S.Flatpieces Of30x6mm Size Being Welded To The Main Frame Ofthe Harrrow.Arrangement For Fixing Of 1 No.100X8mmc-Boltwithbeam Be Made At The Rearand By Welding Vertically2pieces Of M.S. Angles Of35x35x6mm Of 2.5Cms. Length At A Distance Of 7.5Cms. In Themiddle Of Frame. 4. Handle:- Single Handle Made Of M.S. Flat Of 25X6mm And80cms. In Length. The Bolts And Nuts May Be Providedfor Fixing The Handles. The Grip Of Conduit Pipe 30X120mm Of 16 Guage Should Be Welded To The Top And Of The Handle Arms. , Hand Rack :- Hand Rack Of Model Deptt. Of Agriculture H.P. Scope Hand Rack Should Be Of The Following Parts:- 1) Frame:- Frame Should Be Made Ofm.S. Angleiron Of 25X25x3mm Size And 30Cms. In Length. 2) Spike:- 10 Nos. Of Spikes Are Made Of M.S. Round 8Mm Dia Forged Flattened. The Length Of Each Spike Should Be 9Cms And Centre To Centre Distance Between Two Spikes Be 3 Cms. 3) Atleast 20Mm Length Of Each Spike Should Be Welded With Frame Of M.S. Angle 25X25x3mm Of 30Cms. Length. The Lower End Of The Spike Should Be Uniformly Levelled To Alength Of 0.5Cms. And Top Of Spike Should Be Bent So As To Makean Angle Of 15 To 20 Degree With The Ground Level For Proper Penetration Of The Implements. 4) Ferrule:- Ferrule Should Be Conical Shaped Of M.S. Sheet 1.63Mm Thick (16Swg) 120Mm In Lengthdiameter Of The Ferrule At Front Portion Should Be 25Mm. And At The Rear End 20Mm, Rear End Of The Ferrule Should Be Flanged Shaped Having Two Holes. One Hole Should Also Be Provided At The Front Portion. Front Portion Of Ferrule Should Be Riveted With Two Riveted With The Frame And The Rear Portion Should Be Riveted With Condute Pipe Handle.All Dimensions Subject To Variation Of +-2.5% Weight Of Hand Rake Without Handle0.700Kg+-2.5% , Hand Rack With C.P Handlehand Rack Of Model Deptt. Of Agriculture H.P. Scope Hand Rack Should Be Of The Following Parts:- 1) Frame:- Frame Should Be Made Ofm.S. Angleiron Of 25X25x3mm Size And 30Cms. In Length. 2) Spike:- 10 Nos. Of Spikes Are Made Of M.S. Round 8Mm Dia Forged Flattened. The Length Of Each Spike Should Be 9Cms And Centre To Centre Distance Between Two Spikes Be 3 Cms. 3) Atleast 20Mm Length Of Each Spike Should Be Welded With Frame Of M.S. Angle 25X25x3mm Of 30Cms. Length. The Lower End Of The Spike Should Be Uniformly Levelled To Alength Of 0.5Cms. And Top Of Spike Should Be Bent So As To Makean Angle Of 15 To 20 Degree With The Ground Level For Proper Penetration Of The Implements. 4) Ferrule:- Ferrule Should Be Conical Shaped Of M.S. Sheet 1.63Mm Thick (16Swg) 120Mm In Lengthdiameter Of The Ferrule At Front Portion Should Be 25Mm. And At The Rear End 20Mm, Rear End Of The Ferrule Should Be Flanged Shaped Having Two Holes. One Hole Should Also Be Provided At The Front Portion. Front Portion Of Ferrule Should Be Riveted With Two Riveted With The Frame And The Rear Portion Should Be Riveted With Condute Pipe Handle.5) Handle:- The Handle Should Be Made Of Condute Pipe Of 25Mm Dia. & One Meter Length. At The Rear End Of Handle Suitable Rubber/ Plastic Grip Should Be Provided For Proper Handling Of The Rake. All Dimensions Subject To Variation Of +-2.5% Weight Of Hand Rake With Handle1.170Kg+-2.5% , Digging Hoe Without Handle:-Hand Digginghoe Should Be Able To Dig Soil For Preparation Of Seed Bed For Kitchen Garden And Has The Following Parts:- 1) Digging Blade. 2) Spikes With Socket. Digging Blade:- It Should Be Made Of Low Carbon Sheet Of Not Less Than 3.15Mm Thick, The Width Of The Blade At The Rear End Should Be 120 To 125Mm And Length 150Mm.100Mm Portion Of Blade Should Be Straight And 50Mm Portion Should Be Triangular From The Front Side. Semicircular Knotch Of 40Mm Dia Should Be Made At The Rare End At The Centre Of The Blede To Weld The Socket And Spike With The Blade. A Rib Of 75Mm Length And 50 To 20Mm Dia Should Be Made At The Centre Of Blade To Provide Strength To It. 2.Spikes & Socket:- Spike & Socket Should Be Made Of Low Carbon Steel In One Piece And Not Welded. Length Of Spike Should Be 115Mm And Its Width At Rear End And Front Side Should Be 20Mm And 25Mm Respectively. Thickness Of Spike Should Be 8Mm. Socket Should Be Oval Shape Having Dimension 35X30mm & Hieght 25Mm. All Dimensions Subject To Variation Of +-2.5%Weight Of Digging Hoe 0.550 Kg+-2.5% , Tubular Maize Sheller : Suitability For Crops: Maize. Overall Dimensions, Mm : Length : 70. Width : 60. (Diameter) Weight, Gm. : 200. Number Of Teeth : 4 At(Fins). Equal Space. Space Of The Sheller : Octagonal. Materials Used : Gi Plate Of Size 1.22 Mm ( 18 Gauge). , Serrated Sickle. Suitability For Crops : Wheat, Paddy,Grams Etc. Overall Dimensions, Mm : *Length : 375. *Width: 145. *Height :45. *Weight, Kg.:0.20. Length Of Blade,Mm: 235. Length Of Cutting Edge Mm 225. Maximum Width,Mm:28. Maximum Thickness,Mm:1.63. Radious Of Curvature,Mm : 230. Number Of Teeth Per Cm.:5. Handle Length, Mm. :140. Handle Diameter Max.Mm.: 32. Materials Used : *Handle :Plastic/Wooden. *Blade:Spring Steel, High Carbon Steel Etc. , Gardening Hoe ( Small ) : Blade : Itshould Be Made Of High Carbon Steel Sheet Of Thickness 2Mm. It Should Be Beetle Leaf Shape The Length Of Thebladeshould Be 150Mm And Width Near Middle Should Be 55 Mm. It Should Have Two Holes Of 6Mm Dia For Riveting With Pein. Pein:- It Should Be Made Of Mild Steel In One Piece And Not Welded. Total Length Of Pein Including Back Support And Eye Should Be 105Mm And Its Thickness 6Mm. Width Of Support At The Rear End Should Be 28Mm And At Front 15Mm. Front End Should Be Slightly Rounded Off. It Should Have Two Holes Of 6Mm Dia For Riveting With Blade. Blade And Pein Should Be Riveted With Each Other And Not Welded. All Dimensions Subject To Variation Of +-2.5%Weight Of Digging Hoe 0.210Kgs.+-2.5% , Gardening Hoe (Medium) : Blade : Itshould Be Made Of High Carbon Steel Sheet Of Thickness 2Mm. It Should Be Beetle Leaf Shape The Length Of Thebladeshould Be 150Mm And Width Near Middle Should Be 115Mm And Width Near Working Edge 30Mm. Working Edge Should Be Slightly Rounded Off For Penetration Into Soil. It Should Have Two Holes Of 6Mm Dia For Riveting With Pein. Pein:- It Should Be Made Of Mild Steel In One Piece And Not Welded. Total Length Of Pein Including Back Support And Eye Should Be 105Mm And Its Thickness 6Mm. Width Of Support At The Rear End Should Be 28Mm And At Front 15Mm. Front End Should Be Slightly Rounded Off. It Should Have Two Holes Of 6Mm Dia For Riveting With Blade. Blade And Pein Should Be Riveted With Each Other And Not Welded. All Dimensions Subject To Variation Of +-2.5% Weight Of Digging Hoe 0.330Kgs +- 2.5% , Straight Rake : Size : 10 Nos. Teeth. Distance Of Teeth 25 Mm Centre To Centre. Curved Length Ofteeth As Measured From Centre 70Mm. Thickness : 4Mm Nominal. Material : Low Carbon Cr Sheet/Strip Socket: Tapered Socket Of 1.6Mm Thick Sheet /Strip. Overall Length Of Socket Should Be 110Mm.Internal Dia Of Socket At Far End 28Mm And At Near End 20/24 Mm. Socket Should Be Securely Rivetted With 2 Rivets With The Main Frame Of Rake. Handle:- Made Of M.S Pipe Of 25Mm Dia And 18 Gauge Thickness. Length Of Pipe 1225Mm And Pvc Grip Provided At Top Of Handle. Finish: Black Or Coloured Enameled Finish. Tolerances : Nominaltolerances Of + 2.5% In Size.
|
