|
Tender For Special Repair To Bldg No Ta-201(Store Room) Under Ge 865 Ews, Leh; 1 Demolition of cement concrete in ground floor and pavings n. exc 15cm thick below or above ground level complete all as specified and as directed. 2 Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. 3 Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, complete all as specified and as directed. 4 Dismantlng framed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etcunder 40 Sq.cm in secton unframed work, complete all as specified and as directed. 5 Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed. 6 Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and as directed. 7 Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n. exc 1.5 Sqm each complete all as directed by Engr-in-charge. 8 Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge. 9 Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed. 10 Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and gourd bars or grating complete all as spd and as directed by Engr-in-Charge. 11 Dismantling floor, hearth or wall tiling including wall cement mortar bedding (But not backing ) and rubbish of premises complete all as directed. 12 Material & Labour for 25mm thick PCC type B-0 using 12.5mm graded crushed stone aggregate as infloor finishes complete all as specified and as directed. 13 Material & Labour forNon skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm and n.exc 18 Sqm in flooretc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the shade of tile over and including screed bed in cement mortar (1:6) 15mm thick for laying floor tiles complete all as specified and directed. 14 Material & Labour for Glazed ceramic coloured tiles in vertical surfaces of size 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the shade of tiles over and including10mm thick in cement mortar(1:4) in dado/skirting tiles complete all as specified and directed. 15 Material & Labour for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including15 mm thick screed bed in CM 1:4, complete all as specified and as directed. 16 Demolition of reinforced cement concrete in ground floor and pavings nexc 15cm thick below or above ground level complete all as specified and as directed. 17 Material & Labour for form work to sides and sooffits of floor or roof beams haunching, girders bressuments, lintel, cantileres including support overhangs, etc also splays beetween floor and beams, rough finished surfaces of concrete complete all as specified. 18 Material & Labour for reinforced cement concrete type B-0 1:2:4, nominal mix (12.5 mm graded Aggregate) as in beam cantilevers, bressummers, lintels over 1.5 m span, complete all as specified and as directed. 19 Material & Labour for TMT bars10mm dia and over, cut length, bent to shape required , includingcranking , bending spirallyfor hoopingfor coloumns, hooking endsand binding with and includingmild steel wire (annealed) not less than0.9mm dia or securing with clips, complete all as specified and as directed. 20 Material & Labour for steel TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia, complete all as specified and as directed. 21 Material & Labour for9mm thick prelaminated particle boardmedium interior grade, prelaminated oneside with decorated choice lamination & other side balancing whitelamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed. 22 Material & Labour for9mm thick prelaminated particle boardmedium interior grade, prelaminated oneside with decorated choice lamination & other side balancing whitelamination fixed with nails to timber frame work as in ceiling panelling, shelves/boarding complete all as specified and as directed. 23 Material & Labour for 2nd class soft wood clean sawn as in battens for grids of ceiling & liningfixed with nails exc 13 sqcm and n exc 25 sqcm in section complete all as specified and as directed. 24 Material & Labour for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section.complete all as specified and as directed. 25 Material & Labour for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and as directed. 26 Material & Labour for 75 mm PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in plinth protection finished even and smooth with out using extra cement, complete all as specified and as directed. 27 Material & Labour Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade A in plinth protection, complete all as specified and as directed. 28 Material & Labour for PCC type D2(1:4:8) using 40mm graded crushed aggregate as in mass conc and filling of foundation and mass concrete, complete all as specified and as directed. 29 Material & Labour for pre cast solid block masonry set in CM 1:6& casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed. 30 All as per Serial item No 29 above but except blocks. 31 Material & Labour for 10mm thick rendering on other than fair faces of Stone wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed. 32 Material & Labour for 10 mm thick rendering onfair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed. 33 Supply & Fixing 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately) all as directed by Engr-in-Charge. 34 Supply & Fixing for 35mm thick2nd class hardwood framed factory made plain framed paneled shutters (any number ofpanels) with panels of timber flat on both sides (feather edged), or ofveneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge. 35 Supply & Fixing 2nd class hard wood 35 mm thick framed factory made Glazed and skelton shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge.. 36 Supply & Fixing 30mm thick2nd class hardwood plain framed factory made glazed and skeletionwindow/ventilator shutters , open rebated and prepared to receive glass , gauze etc (without sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in SSR part I, Section 8 , clause 8.24(a) supplied and fitted to chowkats , complete all as directed by Engr-in-charge. 37 Material & Labour for preperation of new wood or wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamal paint over a coat of pink primer complete all as specified and as directed. 38 Supply & Fixing sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed. 39 Supply & Fixing in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples. 40 Supply & Fixing 150mm long aluminium anodized, barrel tower bolt of extruded sectioncompleteall as specified and as directed. 41 Supply & Fixing 100mm long aluminium anodized, barrel tower bolt of extruded section complete. 42 Supply & Fixing 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed. 43 Supply & Fixing 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete. 44 Supply & Fixing floor door stopper (Length of cover plate ) 150mm long aluminium alloy body and tongueanodised with hard drawn steel springfixed in floorcompleteall as specified and as directed. 45 Supply & Fixing 75mm long aluminium anodized, butt hinges of extruded sectioncompleteall as specified and as directed. 46 Supply & Fixing 100mm long aluminium anodized, butt hinges of extruded sectioncompleteall as specified and as directed. 47 Supply & Fixing in repair250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed 48 Material & Labour for Cement concrete type D-2,1:4:8 (40mm graded aggreate) 75 mm thick as in sub -floors, sub- bases, floors and pavings,etc. 49 Material & Labour forChequred cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments laid over & including20mm thick cement screed base in cement mortar (1:6) and all as directed by Engr-in - charge. 50 Supply & Fixing mild steel rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar workconfirming to Fe-290, Gde-E-165 complete all as specified and as directed. 51 Supply & Fixing mild steel confirming to Fe-410W(GdeE-250)as in joist, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated 52 Supply & Fixing pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws as specified. 53 Material & Labour for preparation new steel surfaces of any description, not otherwise described, over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and as directed. 54 Material & Labour for preperation of new plastered wall surfaces of any description and applying three coat of white wash complete all as specified and as directed. 55 Material & Labour for applying two coats of cement base paint on newly plastered surfaces including preparation of surfaces, complete all as specified and as directed. 56 Supply & fixing in repair 600x450mm bevelled edge looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with cromium plated brass screws and cup washers complete all as specified. 57 Supply & Fixing in repair19mm dia mild steel, chromium plated curtain rods,withbrackets, end bulbs all as specified and as directed by Engr-in-charge. 58 Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as spfd and directed by Engr-in-Charge. 59 Material & labour for Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC FRLS insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC FRLS insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth leadall as specified and directed for the followings:- 60 (a) One light/exhaust fan point controlled by one way switch 61 (b) One switch socket outlet 6 Amps, 230 volts point on Same board 62 (c) One switch socket outlet 6 Amps, 230 volts point on independent board 63 Material & labour for Point wiring complete with 4.0Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts FRLS cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 4.0 Sqmm copper conductor FRLS cable as continuous earth lead complete all as specified and directed. 64 Supply and fixing lamp holder insulated body with back plate complete all as specified and directed. 65 Supply and fixing Switch piano flush button single pole 6 Amps 230 volts one way complete all as directed. 66 Supply and fixing switch Socketout let two in one5 pin 6 Amps flush type 230 volts complete all as directed. 67 Supply and fixing switch Socket combination out let multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as directed. 68 Supply and fixing ceiling rose, surface Bakelite three terminals complete all as directed. 69 Supply and fixing sheet metal enclosure for DBs double door when MCBs to be used single pole & neutral 240 Volts 8Ways all as specified and directed by Engr-in-Charge. 70 Supply and fixing sheet metal enclosure for DBs double door when MCBs to be used single pole & neutral 240 Volts 4Ways all as specified and directed by Engr-in-Charge. 71 Supply and fixing MCB SPN 63 Amp 240 Volts 50 Hz AC, C SeriesISI marked all as specified and directed by Engr-in-Charge. 72 Supply and fixing MCB SP 6-32 Amps 240 Volts50 Hz AC, C SeriesISI marked all as specified and directed by Engr-in-Charge. 73 Supply and Fixing in repairs LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 74 Supply and fixing in repairs LED light fitting 1X9 W/ 1X 10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. 75 Supply and fixing in repairs recess mountingLED light fitting 36Wattincl. seperate electronic driver & high brightness SMD LEDs ultra modern suitable for armstrong /grid /POP ceilling in MS housing with high brightness 4000K LEDs suitable for230 Volt50 Hz Diffused type optics 2x2 in size complete with all accessories internaly prewired andincluding connectingup with twin core twisted flexible copper conductor cable of suitable size complete . 76 Material & labour for earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanisedstrip 4.0 mm dia as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 20 mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised Iron/steel of size 600x600x6 mm, supplying and laying charcoal stone aggregate) chamber and mild steel angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded crushed stone aggregate reinforced with 8 mm dia TMT bars @75mm C/C both ways with mild steel handle 12 mm dia, PGI funnel with wire mesh, 20 mm dia GI pipe light grade incl. watertep for watering all as shown in drawing
|
