|
Tender For Reorganization Of Piped Water Supply Scheme Of Kuri Bhagtasani Tehsil Luni District Jodhpur Under Jjm - REORGANISATION OF PIPED WATER SUPPLY SCHEME OF VILLAGE KURI BHAGTASANI TEHSIL LUNI DISTRICT JODHPUR UNDER JAL JEEVAN MISSION Sl. No. Item Description 1 RISING MAIN PIPE LINES 2 PHED Revised BSR 20231.1 Providing, lowering, laying in trenches, aligning, fixing in position and jointing Ductile Iron (DI) ISI marked K-7 grade S&S pipes as per IS:8329-2000 (amended up to date), with internal cement mortar lining suitable for potable water with rubber ring (EPDM) joints as per IS:5382-1985 including all taxes (Central and local), transportation and freight charges, inspection charges, loading/ unloading charges, including cost of labour and material, specials (Tee, bend etc.) satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer-in-charge. (excluding earth work)Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately. 3 1.1.3 150 mm 4 1.1.4 200 mm 5 1.1.5 250 mm 6 PHED Revised BSR 2023 4.1 Earth work in excavation by mechanical means (Hydraulic Excavator)/manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr. including required all safety provisions etc.: All kinds of soil 7 PHED Revised BSR 2023 1.15 Providing and fixing of flanged/plain ended MS specials from MS sheet strips of relevant IS specification of approved thickness by welding, lowering, laying and aligning, fixing in position at all level/depths in trenches complete including all taxes, material , labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge 8 1.15.1 MS pipe special upto 600mm dia (with minimum 5.0 mm thickness sheet) 9 PHED Revised BSR 2023 4.5 Dismantling of cement concrete pavement for pipe line line and chambers by mechanical means using pneumatic tools, cutting the peripheral edge by CC cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters.Measurement for dismantled trench to be made as per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, re-handling of material/earth to complete the tasks as per technical specification and scope of work. 10 PHED Revised BSR 2023 4.7 Providing and laying in position cement concrete M10 grade nominal mix 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 40 mm nominal size) in base course complete including all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. Measurement for CC work to be made as per standard trench width specified in tender document and no extra payment shall be made be made for trench width morethan specified, completeworkasper technicalspecification and scope of work. 11 PHED Revised BSR 2023 4.8 Providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. Measurement for CC work to be made as per standard trench width specified in tender document and no extra paymentshall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 12 4.8.1 M20 grade Nominal Mix 1: 1.5: 3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size). 13 4.8.2 Plain cement concrete pavementof M-30 Grade 14 PHED Revised BSR 2023 4.9 Removing& Re-fixing of Precast concrete interlocking blocks for laying of pipe line by manual method, stacking of serviceable & non serviceable material separately, disposal of dismantled material lead up to 50 mtr. The C.C. interlocking paving blocks be laid on average 25 mm thick bed of coarse sand and the joints to be filled with fine sand. Laying procedure on compacted sub base as defined. Complete job is to be executed as per the directions of Engineer in charge. The rates to be inclusive of fixing of 70 percent reusable precast concrete interlocking block and cost of required new precast concrete interlocking block against damaged, including alllead and lift as per Technical specifications. (Interlocking block manufactured by fully computerized automatic stationery hydraulic vibro pressed machine & full computerized automatic batching plant of class A-1 as per BS:6717-2001. Tensile splitting strength and breaking load as per BS: 6717-2001 Colour: Grey cement natural colour. Variation in Dimension : Less than 1.6 mm Variation in thickness: Less than 3.2 mm)Note:Ifexistingprecastblockusedmorethan70%,thanforevery1%use above 70%, deduction of 1% in cost shall be done for every 1% use above 70%. 15 4.9.1 60 mm thick. 16 4.9.2 80 mm thick. 17 4.9.3 100 mm thick 18 PHED Revised BSR 20231.3 Providing, lowering, laying, aligning, fixing in positionand jointing at all level/depths DI standard specials with rubber ring (EPDM)/nut bolt and insertion sheet and jointing as per IS:9523-2000 or as amended up to date, such as tees, bends, tapers, caps etc. within trenches in DI pipe line complete including all material, labour, taxes, testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge (excluding earth work). 19 1.3.2 All End Flanged 20 1.3.2.1 Up to 300 mm Diameter 21 PHED Revised BSR 2023 6.1 Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves straight and pocket less body passage of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/FG200 Stem- AISI-410, Body Seat ring, Wedge facing ring & Bushes- LTB2/SS, Face to face dimensions as per IS:14846/2000 (amended up to date), Epoxy (Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS:1538. Nut-Bolt confirming to IS:1363 and IS:1367/CS/galvanised steel Insertion rubber of black EPDM 6mm thick. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 22 6.1.1 Manually Operated CI Sluice valve of Class PN-1.0 23 6.1.1.2 100 mm HW 24 6.1.1.3 125 mm HW 25 6.1.1.4 150 mm HW 26 6.1.1.5 200 mm HW 27 6.1.1.6 250 mm HW 28 PHED Revised BSR 20236.5 Providing, lowering, aligning, fixing in position and Jointing in pipe line, CI single Air Valve Flanged/Screwed type of approved makes for following pressure rating & dia complete, confirming to IS:14845-2000 (amended up to date) and of following specifications: Body, Cover and Cowl - Grey Cast Iron as per IS:210- FG 200, Float Stainless Steel AISI:304/IS:3444, Float Guide- HBT1, Body seat ring - Leaded tin bronze/SS, Seal ring and face ring - EPDM/NBR, Ends flanged according to IS:6418 or Screwed type shall have external pipe threads conforming to IS:554 Fasteners - CS Epoxy paint inside outside of food grade safe for drinking water,Valves including all material, labour, testing and commissioning as per Technical Specifications and as per direction of Engineer in charge.Note: Rates are exclusive of connecting tee, pipe piece and earth work. 29 6.5.1 Class PN 1.0 30 6.5.1.2 25 mm S-1 Type 31 6.5.1.3 40 mm S-1 Type 32 PHED Revised BSR 2023 6.6 Providing, lowering, aligning, fixing in position and Jointing in pipe line, CI Double Acting Kinetic Air Valve with isolating Sluice Valve of approved makes for following pressure rating & dia complete, confirming to IS:14845-2000 (amended up to date) and of following specifications: Body, Cover and Cowl-Grey Cast Iron as per IS:210-FG 200, Float - Stainless Steel AISI 304/IS:3444, Float Guide- HBT 1.0 HP Orifice- HTB2/SS, Body seat ring - Leaded tin bronze/SS. Seal ring and face ring - EPDM/NBR, Ends flanged according to IS:6418, Fastners - CS, Epoxy paint inside outside of food grade safe for drinking water, Valves including all material, labour, testing and commissioning as per Technical Specifications and as per direction of Engineer in charge.Note: Rates are exclusive of connecting tee, pipe piece and earth work. 33 6.6.1 Class PN 1.0 34 6.6.1.2 50 mm 35 6.6.1.3 80 mm 36 PHED Revised BSR 20236.17 Providing, lowering, laying, aligning, fixing in position and jointing CI dismantling joint (Suitable for Sluice valves etc.) as per IS specifications complete of the following sizes including all jointing material, cost ofall labour, testing and commissioning Technical Specifications and as per direction of Engineer. Class PN 1.0 37 6.17.2 100 mm dia. 38 6.17.3 125 mm dia. 39 6.17.4 150 mm dia. 40 6.17.5 200 mm dia. 41 6.17.6 250 mm dia. 42 PHED Revised BSR 20236.3 Providing, lowering, aligning, fixing in position in pipe line, CI double flanged swing type Non Return Valves (NRV) of approved make of following Pressure rating & dia complete, confirming to IS: 5312 (Part-1)/2004 (amended up to date) and of following specifications: Body, Cover & disc of Grey cast iron of IS:210/FG200. Face to face dimensions as per IS:5312 (Part-1):2004, Flanges Drilled as per IS:1538. Epoxy (Non-Toxic & suitable for drinking water) applied on body, cover and disc inside and outside. Body seat ring of SS/CS Door face ring - EPDM/Neoprene (food grade quality), Shaft of SS-AISI-410, Hinge Malleable cast iron/SS AISI:316, Bonnet Gasket EPDM, Bush- Leaded tin Bronze/ PTET, Gasket EPDM/NBR, Nut-Bolt as per IS:1363 and IS:1367 (galvanised steel), Insertion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in- charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 43 Class PN 1.0 44 6.3.1.2 100 mm dia 45 6.3.1.3 125 mm dia 46 6.3.1.4 150 mm dia 47 6.3.1.5 200 mm dia 48 6.3.1.6 250 mm dia 49 PHED BSR 202311.1 SITC of D/F Full bore type Electromagnetic Flow Meter of approved make of following dia and specifications complete: Media: Water (Raw/Chlorinated), Pressure: up to 1.5MPa, Process temp:- 50 deg C, Flow/Meter Tube: SS-304, Electrode: SS -AISI 316L/ Hastelloy C276/Tantalum, Lining Matrial: Hard Rubber/ Neoprene/ Poly-urethane (PU), Flange: SS/CS, Flange Standard & Rating: ANSI:150, Coil housing: SS AISI:304/ Carbon Steel/ Die Cast Aluminium, with anticorrosive paint & provide completely sealed (leak proof) construction as per requirement of IEC:60529, Accuracy : ± 0.5% M.V.- velocity 0.3 to 10 m/s, Transmitter/ signal convertor Enclosure: Die Cast Aluminium, Power Supply: 80-240 V AC-50Hz, Output 1: 4-20 mA, Output 2: Pulse, Communication Output: RS 485/ Heart, Display Type: LCD/ LED Display, Cable Entry: M20 x 1.5, Provision of RAM/PROM to store calibration and configuration parameters and totalizer value during power failure, Protection category- IP 68 for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, if required, and all materials required for making connection etc. complete in all respect as per technical specification and direction of Engineer In-Charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 50 11.1.3 EFM 100 mm 51 11.1.5 EFM 150 mm 52 11.1.6 EFM 200 mm 53 11.1.7 EFM 250 mm 54 11.1.8 EFM300 mm 55 DISTRIBUTION PIPE LINES 56 PHED Revised BSR 20231.4 Providing, lowering, laying and jointing in trenches, standard lengths HDPE ISI marked Pipes as per IS-4984:1995 (amended up to date) with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/compression fitting joint or flanged joint and specials jointing pipe by electro fusion welding method, including all taxes, transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (Tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer in-charge of following class and diameter. (excluding earth work). Note: Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately.Supply may be in coil or straight length in 6 M/12 M. 57 1.4.1 HDPE PE-80PN-6 58 1.4.1.1 75 mm dia 59 1.4.1.2 90 mm dia 60 1.4.1.3 110 mm dia 61 PHED Revised BSR 20231.5 Providing, lowering, laying and jointing in trenches, standard lengths HDPE ISI marked Pipes as per IS-4984:1995 (amended up to date) with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe by butt fusion/ electro fusion welding method, including all taxes, transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (Tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer in-charge of following class and diameter. (excluding earth work).Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately.Supply of pipe shall be in straight length in 6/12 M. 62 1.5.1 HDPE PE-80PN-6 63 1.5.1.1 125 mm dia 64 1.5.1.2 140 mm dia 65 1.5.1.3 160 mm dia 66 1.5.1.4 180 mm dia 67 PHED Revised BSR 20231.1 Providing, lowering, laying in trenches, aligning, fixing in position and jointingDuctileIron(DI)ISI markedK-7gradeS&Spipesas per IS:8329-2000 (amended up to date), with internal cement mortar lining suitable for potable water with rubber ring (EPDM) joints as per IS: 5382-1985 including all taxes (Central and local), transportation and freight charges, inspection charges, loading/ unloading charges, including cost of labour and material, specials (Tee, bend etc.) satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer-in-charge. (excluding earth work) Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately. 68 1.1.3 150 mm 69 1.1.4 200 mm 70 1.1.5 250 mm 71 1.1.6 300 mm 72 1.1.7 350 mm 73 PHED Revised BSR 2023 4.1 Earthwork in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth .1.5 min width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5m, disposed earth to be leveled and neatly dressed : All kinds of soil 74 PHED Revised BSR 2023 1.15 Providing and fixing of flanged/plain ended MS specials from MS sheet strips of relevant IS specification of approved thickness by welding , lowering, laying and aligning, fixing in position at all level/depths in trenches complete including all taxes, material , labour, inside lining, outside coating , testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge 75 1.15.1 MS pipe special upto 600mm dia (with minimum 5.0 mm thickness sheet) 76 PHED Revised BSR 2023 4.5 Dismantling of cement concrete pavement for pipe line line and chambers by mechanical means using pneumatic tools, cutting the peripheral edge by CC cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. Measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width ethanspecified, re-handling of material/earth to complete the tasks as per technical specification and scope of work. 77 PHED Revised BSR 2023 4.6 Dismantling of flexible pavement for pipe line line and chambers by mechanical meansusing pneumatic tools, breaking to piecesnot exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. Measurement for dismantled trench to be made as per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, re-handling of material/earth to complete the tasks per technical specification and scope of work. 78 4.6.1 Bituminous courses 79 4.6.2 Granular courses 80 PHED Revised BSR 2023 4.7 Providing and laying in position cement concrete M10 grade nominal mix 1:3:6 (1 Cement : 3coarse sand:6 graded stone aggregate 40 mm nominal size) in base course complete including all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. Measurement for CC work to be made as per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, complete work asper technicalspecification and scope of work. 81 PHED Revised BSR 2023 4.8 Providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. Measurement for CC work to be made as per standard trench width specified in tender document and no extra paymentshall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 82 4.8.1 M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 83 4.8.2 Plain cement concrete pavementof M-30 Grade 84 PHED Revised BSR 2023 4.9 Removing& Re-fixing of Precast concrete interlocking blocks for laying of pipe line by manual method, stacking of serviceable & non serviceable material separately, disposal of dismantled material lead up to 50 mtr. The C.C. interlocking paving blocks be laid on average 25 mm thick bed of coarse sand and the joints to be filled with fine sand. Laying procedure on compacted sub base as defined. Complete job is to be executed as per the directions of Engineer in charge. The rates to be inclusive of fixing of 70 percent reusable precast concrete interlocking block and cost of required new precast concrete interlocking block against damaged, including alllead and lift as per Technical specifications. (Interlocking block manufactured by fully computerized automatic stationery hydraulic vibro pressed machine & full computerized automatic batching plant of class A-1 as per BS:6717-2001. Tensile splitting strength and breaking load as per BS: 6717-2001 Colour: Grey cement natural colour. Variation in Dimension : Less than 1.6 mm Variation in thickness: Less than 3.2 mm)Note:Ifexistingprecastblockusedmorethan70%,thanforevery1%use above 70%, deduction of 1% in cost shall be done for every 1% use above 70%. 85 4.9.1 60 mm thick. 86 4.9.2 80 mm thick. 87 4.9.3 100 mm thick 88 RCC RESERVOIRS 89 PHED Revised BSR 20233.3 ConstructionandcommissioningofRCCINTZEtypeOverHeadServiceReservoirof followingcapacityandstagingaspertheScopeofworkandTechnicalspecifications, consisting of the following main activities: - 90 a)Topographicsurvey,preparationofsitecontourplan,conductingSBCtest andits approvalfromdepartment beforeconstruction.Submissionandapprovalofconcretemix design and water quality test report for water to be used in construction.b) Excavation in all types of soil, PCC below foundation, all RCC Work, Plinth protection all around the structure including all material, labour, shuttering, scaffolding etc.c)OHSRshallbeprovidedwithadequateplinthprotectionallaroundthestructureina width starting from edge of structure at GLand extending at least up to1.0m beyond the edge of outer most projection of OHSR.The plinth protection shall consist of 150mm thick PCC in M-15 grade concrete laid over 150mm thick layer of compacted soil.d) Providing and applying two coats of food grade epoxy paint on the inside surface on the top dome, edge beam and 600 mm height of the vertical wall.e)Conducting successfully hydro test and water tightness test as per I.S. code.f) Providing and applying three coats of anti-carbonation paint on the top surface of the Top Dome.g) Providing and applying three coats of cement-based paint on the external surface of the container, balcony, cone wall, columns & beams etc..h) Providing and fixing SS-304 ventilator, SS 304 manhole frame and cover and SS-304 ladder from top dome/Slab to bottom dome/Slab inside container.i) Providing and fixing of MS section ladder from the last landing to balcony having railing all around it and MS ladder with safety cage from balcony to top dome/slab.j) Providing and fixing water level indicator (float type). 91 k)Providingandfixingofhandrailingallaroundthebalcony,topdomeandstaircase consisting of 25mm diameter Class-B GI pipe in two rows and 1000 mm high, 50X50X6mm angle iron vertical post at a maximum spacing of 1500mm centres.l) All MS parts to be painted with two coats of the enamel paint over the primer coat of red oxide.m)Providingandfixingof150mmwidePVCwaterbarfortheconstructionjointsinthe container (vertical wall & cone wall).n) Providing one Aluminium portable ladder of appropriate length to access first landing (3.5 to 4.5m above GL) from ground.o)Lightingarrestorconsistingofprovidingandfixingof2Nos. ofchemicalearthingand connecting it to the conical cover of SS ventilator with two separate GI strips of 50mmX3mm.p) CI/DI puddle collar shallbe fixed inthe bottomdome/ slabfor connectinginlet, outlet, overflow and washout pipe of the reservoir.q) Painting the name of the scheme and other details on the reservoir, and any other work related to structure as per the directions of Engineer-in- Charge, Technical Specification and Scope of Work.r)Inlet,outlet,overflow,washoutpipesandvalvesarenotincludedinthiswork, provision for the same shall be taken separately. 92 3.2.4 Rates for RCC OHSR, SBC 10 T/Sqm, SEISMIC ZONE-II & STAGING 18 M 93 3.2.4.6 400KL capacity 94 3.2.4.7 500KL capacity 95 PHED Revised BSR 2023 3.7 Providing and fixing double flanged ISI marked DI Class K-9 pipes as per IS:8329-2000 (amended up to date), as vertical pipes for RCC Reservoirs including specials required such as duck foot bend, bend, tee etc. providing and fixing clamps at every 3 mtr, jointing materials such as nuts, bolt, rubber packing, hydraulic testing etc. complete in all respect up to and from valve chamber as per direction of EIC, Technical Specification and Scope of work. 96 3.7.2 150 mm 97 3.7.3 200 mm 98 3.7.4 250 mm 99 3.7.5 300 mm 100 3.7.6 350 mm 101 PHED Revised BSR 2023 6.1 Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves straight and pocket less body passage of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/FG200 Stem - AISI-410, Body Seat ring, Wedge facing ring & Bushes - LTB2/SS, Face to face dimensions as per IS:14846/2000 (amended up to date), Epoxy (Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS:1538. Nut-Bolt confirming to IS:1363 and IS:1367/CS/ galvanised steel Insertion rubber of black EPDM 6mm thick. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 102 6.1.1 Manually Operated CI Sluice valve of Class PN-1.0 103 6.1.1.4 150 mm HW 104 6.1.1.5 200 mm HW 105 6.1.1.6 250 mm HW 106 6.1.1.7 300 mm HW 107 6.1.1.8 350 mm HW with gear 108 PHED Revised BSR 20236.3 Providing, lowering, aligning, fixing in position in pipe line, CI double flanged swing type Non Return Valves (NRV) of approved make of following Pressure rating & dia complete, confirming to IS: 5312 (Part-1)/2004 (amended up to date) and of following specifications: Body, Cover & disc of Grey cast iron of IS:210/FG200. Face to face dimensions as per IS:5312 (Part-1):2004, Flanges Drilled as per IS:1538. Epoxy (Non-Toxic & suitable for drinking water) applied on body, cover and disc inside and outside. Body seat ring of SS/CS Door face ring - EPDM/Neoprene (food grade quality), Shaft of SS-AISI-410, Hinge Malleable cast iron/SS AISI:316, Bonnet Gasket EPDM, Bush- Leaded tin Bronze/ PTET, Gasket EPDM/NBR, Nut-Bolt as per IS:1363 and IS:1367 (galvanised steel), Insertion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in- charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 109 Class PN 1.0 110 6.3.1.4 150 mm dia 111 6.3.1.5 200 mm dia 112 6.3.1.6 250 mm dia 113 6.3.1.7 300 mm dia 114 6.3.1.8 350 mm dia 115 PHED Revised BSR 20236.17 Providing, lowering, laying, aligning, fixing in position and jointing CI dismantling joint (Suitable for Sluice valves etc.) as per IS specifications complete of the following sizes including all jointing material, cost of all labour, testing and commissioning Technical Specifications and as per direction of Engineer. Class PN 1.0 116 6.17.3 100 mm dia. 117 6.17.4 150 mm dia. 118 6.17.5 200 mm dia. 119 6.17.6 250 mm dia. 120 6.17.7 300 mm dia. 121 6.17.8 350 mm dia. 122 PHED Revised BSR 20231.3 Providing, lowering, laying, aligning, fixing in positionand jointing at all level/ depths DI standard specials with rubber ring (EPDM)/ nut bolt and insertion sheet andjointingasperIS:9523- 2000 or as amended up to date,suchastees,bends, tapers,caps etc.withintrenches inDIpipe line completeincluding all material, labour, taxes, testingand commissioningalong with pipe line as per technical specifications anddirection of Engineer-in-charge (excluding earth work). 123 1.3.2 All End Flanged 124 1.3.2.1 Up to 300 mm Diameter 125 1.3.2.2 Above 300mm and up to 600 mm diameter 126 PHED Revised BSR 202311.4 SITC of Ultrasonic Level Transmitter suitable for measuring water level in reservoir, Normal Powered 24VDC, Type of Transmitter: Two Wire (4-20 mA), Cable Entry: 1/2 NPT (F), Sensor Material: PP, slip-on Flange: 2 ½” Flange, Material of Construction for Slip-on flange: PP, output 4~20mA, HART compatible, accuracy +/_ 0.2 % as per detailed Technical specification, scope of work and direction of Engineer in charge. 127 11.4.1 Measuring range 0.0 to 6.0 mtr 128 PHED Revised BSR 2023 1.15 Providing and fixing of flanged/plain ended MS specials from MS sheet strips of relevant IS specification of approved thickness by welding , lowering, laying and aligning, fixing in position at all level/depths in trenches complete including all taxes, material , labour, inside lining, outside coating , testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge 129 1.15.1 MS pipe special upto 600mm dia (with minimum 5.0 mm thickness sheet) 130 Civil Work 131 PHED Revised BSR 2023 8.1 ConstructionofPumphouseofrequiredsizesuitableforinstallationof maximum 4 no. monoblock pump sets as per approved GA drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. The plinth area of pump house shall be area of measurement. 132 PHED Revised BSR 2023 8.5 Construction of Pump house of RCC framed structure with pump pit in RCC walls as per scope of work and technical specification complete work in all respect including electrical works for indoorand outdoor lighting and fans, rain water drainage, sanitary, plumbing, monorail/ EOT crane etc. complete as per direction of Engineer-in-charge. The GA, structure, electrical, sanitary, P&ID, SLD to be prepared by the contractor and submitted to department for approval for earth quake zone II. 133 8.5.2 Pump House with suitable EOT arrangement with Girder 134 PHED Revised BSR 2023 8.2 Construction of boundary wall of Brick/ stone masonary as per enclosed GA drawing, scope of work and technical specifications complete work in all respect. Brief details of boundary wall parameter is as below:1. Depth of foundation- 900 mm.2. PCC in M-10, width -900 mm and thickness 100 mm,3. Stone masonary in CM: 1:6 section of foundation above PCC, 600 mm (W )x 450 mm (D) and 450 mm (W) x 450 mm (D) 4. Superstructure work: Stone masonary in CM: 1:6, W-300, height-1650 mm,/ Brick work in CM: 1:6 W-230 mm, height- 1650 mm.5. Cement mortar pointing on Stone masonary and cement mortar plaster 20 mm thick on brick masonary in CM 1:6.6. Expansion joint shall be on every 30 mtr.7. On top of wall there shall be CC Coping 75 mm thick (1:2:4) shall be provided.8. Pillar for main gate 350x350 mm in size is part of boundary wall.9. Cement paint of approved colour in 3 coat shall be done. 135 PHED Revised BSR 20239.1 Construction of RCC Sluice valve chamber for different type of valves including earthwork excavation, 100mm PCC M15 as leveling course, RCC M25 grade for base slab, side wall & cover sla, including cost of steelreinforcement, form work, Pre-cast, Plastic encapsulated CI/MS Foot Rest, MS flats for the support of pre-cast, proper curing of concrete work complete in all respect as per specifications and standard drawings and as directed by Engineer-in-Charge. 136 9.1.2 For Class-A loading 137 9.1.2.1 Sluice valve chamber of size1.13m x0.85m x1.27m for pipe size-upto100mm 138 9.1.2.2 Sluice valve chamber of size1.17m x0.95m x1.415m for pipe size-from 125-to-150mm 139 9.1.2.3 Sluice valve chamber of size1.26m x1.185m x1.82m for pipe size-from 200-to-300mm 140 9.1.2.4 Sluice valve chamber of size1.39m x1.43m x2.185m for pipe size-from 350-to-450mm & (For VTC) 141 PHED Revised BSR 2023 8.3 Providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. 142 Pump Machinery 143 PHED Revised BSR 2023 5.7 Providingandfixing atsitewithnecessarypacking, HorizontalCentrifugal Split Casting pumps with 4 poleinduction motor operating at synchronised speed of speed 1500 RPM as per IS 12615: 2011 or amended up to date , CI casingandcasingring,SS316impeller,SS410Shaftandshaftsleeve, couplingguard,commonbaseplate,foundationbolts,Cementconcrete foundation etc. complete with all respect as per the specification and scope ofworkanddirectionofEngineerinChargeoffollowingrangeofduty conditions.Note: Duty condition of required pump shall also be mentioned in BoQ. 144 5.7.2 Discharge 20 to 30 LPS and head 31 to 40 M 145 5.7.3 Discharge 20 to 30 LPS and head 41 to 50 M 146 PHED Revised BSR 2023 1.15 Providing and fixing of flanged/plain ended MS specials from MS sheet strips of relevant IS specification of approved thickness by welding , lowering, laying and aligning, fixing in position at all level/depths in trenches complete including all taxes, material , labour, inside lining, outside coating , testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge 147 1.15.1MS pipe special upto 600mm dia (with minimum 5.0 mm thickness sheet) 148 PHED Revised BSR 2023 6.1 Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves straight and pocket less body passage of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/FG200 Stem - AISI-410, Body Seat ring, Wedge facing ring & Bushes - LTB2/SS, Face to face dimensions as per IS:14846/2000 (amended up to date), Epoxy (Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS:1538. Nut-Bolt confirming to IS:1363 and IS:1367/CS/ galvanised steel Insertion rubber of black EPDM 6mm thick. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 149 6.1.1 Manually Operated CI Sluice valve of Class PN-1.0 150 6.1.1.3 125 mm HW 151 6.1.1.4 150 mm HW 152 6.1.1.5 200 mm HW 153 6.1.1.6 250 mm HW 154 6.1.1.7 300 mm HW 155 PHED Revised BSR 2023 6.3 Providing, lowering, aligning, fixing in position in pipe line, CI double flanged swing type Non Return Valves (NRV) of approved make of following Pressure rating & dia complete, confirming to IS: 5312 (Part-1)/2004 (amended up to date) and of following specifications: Body, Cover & disc of Grey cast iron of IS:210/FG200. Face to face dimensions as per IS:5312 (Part-1):2004, Flanges Drilled as per IS:1538. Epoxy (Non-Toxic & suitable for drinking water) applied on body, cover and disc inside and outside. Body seat ring of SS/CS Door face ring - EPDM/Neoprene (food grade quality), Shaft of SS-AISI-410, Hinge Malleable cast iron/SS AISI:316, Bonnet Gasket EPDM, Bush- Leaded tin Bronze/ PTET, Gasket EPDM/NBR, Nut-Bolt as per IS:1363 and IS:1367 (galvanised steel), Insertion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in- charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 156 6.3.1 Class PN 1.0 157 6.3.1.3 125 mm dia 158 6.3.1.4 150 mm dia 159 6.3.1.5 200 mm dia 160 6.3.1.6 250 mm dia 161 6.3.1.7 300 mm dia 162 PHED Revised BSR 20236.17 Providing, lowering, laying, aligning, fixing in position and jointing CI dismantling joint (Suitable for Sluice valves etc.) as per IS specifications complete of the following sizes including all jointing material, cost of all labour, testing and commissioning Technical Specifications and as per direction of Engineer. Class PN 1.0 163 6.17.3 125 mm dia. 164 6.17.4 150 mm dia. 165 6.17.5 200 mm dia. 166 6.17.6 250 mm dia. 167 6.17.7 300 mm dia. 168 PHED Revised BSR 20231.3 Providing, lowering, laying, aligning, fixing in positionand jointing at all level/ depths DI standard specials with rubber ring (EPDM)/ nut bolt and insertion sheet and jointing as per IS:9523- 2000 or as amended up to date, such as tees, bends, tapers, caps etc. within trenches in DI pipe line completeincluding all material, labour, taxes, testingand commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge (excluding earth work). 169 1.3.2 All End Flanged 170 1.3.2.1 Up to 300 mm Diameter 171 PHED Revised BSR 20237.2 SITC STAR DELTA Starter type LT Panel of following rating: all switchgears are of PHED approved makes, CRCA sheet of Panel enclosure is of TATA/Essar 1.6mm/2.0mm thick duly Electrostatic Powder Coated with angle frame including other ancillaries (Insulators, Acrylic Sheet, Backlight Sheet, Hardware, Wire, Name Plates, Lugs, PVC Channel, MCB Chanel, Lock, Hing, Bidding, Connectors, Neutral Links, Spiral, Saddle & Packing Material) etc. and 100A/125A,TPN, Aluminium Bus Bar with Colour coated heat shrinkage sleeves complete as per Technical Specifications and as per direction of Engineer-In-Charge. 172 PHED Revised BSR 20237.2.6 STAR DELTA STARTER 22.0 KW (30.0 HP) - : For 2 motors (1 W+ 1S) I/C- MCCB 125A TPN 25 KA With T/M Based Over Current & Short Circuit Protection (1), Spreaders (2), Extended Rotary Handle (1), Analog Voltmeter 96x96mm (0-500V) (1), Volt Selector Switch (1), Analog Ammeter 96x96mm ( 0-60A ) (1), Amp. Selector Switch (1), C. T. 125/5A CL 1.0 5VA (3), Indicating Lights ( Red-1, Yellow -1) (2), Indicating Lights (Blue-1) (1), Control MCB 6A SP 10 KA C-Curve (3) and O/G- MCCB 100A TPN 25 KA With T/M BasedOver Current & Short Circuit Protection (2), Power Cont 40A TP AC3 Duty(2), 2 NO+2 NC Aux. Block(2), Thermal Overload Relay (23-32A )(2), Control MCB 6A SP 10 KA C Curve (2), Single Phase Preventer (2), Indicating Lights (Red- 1, Green - 1, Amber-1)(6), Push Button 22.5 ( Red - 1, Green - 1 )(4), Selector Switch 1 Pole, 2 Way (2), Capacitor 440VAC Heavy Duty MPP Type 12.5 Kvar (2), S/D Timer(2) 173 RUIDP ISOR 202243.6 SITC of Soft Starters with panel supplied by manufacturer conforming to applicable standards with logic inputs & outputs, relay outputs and analogue outputs, plug in I/O connections, display of electrical parameters, state of load & operating time, RS 485 serial link for connections to Modbus. 174 43.6.2 30 KW 175 PHED Revised BSR 20232.19 Supply & Fixing of ISI marked three core PVC flat submersible cableas per IS:694-1990 or amended up to date and conductor as per class 5 of IS:8130-1980 including making connection etc. 176 2.19.4 3 core 16.0 Sq.mm 177 PHED Revised BSR 20232.2 Supply & Fixing XLPE insulated/P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 Cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 178 2.20.3 25.0 Sq.mm, 3.5 core 179 2.20.4 35.0 Sq.mm, 3.5 core 180 PHED Revised BSR 20232.21 Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. B class watering Pipe including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and CC finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size 300mmx300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 181 PHED Revised BSR 20232.32 Supplying & Installing 100mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. 182 SLUICE VALVES & INTER CONNECTION 183 PHED Revised BSR 20236.1 Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves straight and pocket less body passage of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/FG200 Stem - AISI-410, Body Seat ring, Wedge facing ring & Bushes - LTB2/SS, Face to face dimensions as per IS:14846/2000 (amended up to date), Epoxy (Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS:1538. Nut-Bolt confirming to IS:1363 and IS:1367/CS/ galvanised steel Insertion rubber of black EPDM 6mm thick. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 184 6.1.1 Manually Operated CI Sluice valve of Class PN-1.0 185 6.1.1.1 80 mm HW 186 6.1.1.2 100 mm HW 187 6.1.1.3 125 mm HW 188 6.1.1.4 150 mm HW 189 6.1.1.6 200 mm HW 190 6.1.1.7 250 mm HW 191 6.1.1.8 300 mm HW 192 6.1.1.9 350 mm with Gear 193 PHED Revised BSR 2023 6.3 Providing, lowering, aligning, fixing in position in pipe line, CI double flanged swing type Non Return Valves (NRV) of approved make of following Pressure rating & dia complete, confirming to IS: 5312 (Part-1)/2004 (amended up to date) and of following specifications: Body, Cover & disc of Grey cast iron of IS:210/FG200. Face to face dimensions as per IS:5312 (Part-1):2004, Flanges Drilled as per IS:1538. Epoxy (Non-Toxic & suitable for drinking water) applied on body, cover and disc inside and outside. Body seat ring of SS/CS Door face ring - EPDM/Neoprene (food grade quality), Shaft of SS-AISI-410, Hinge Malleable cast iron/SS AISI:316, Bonnet Gasket EPDM, Bush- Leaded tin Bronze/ PTET, Gasket EPDM/NBR, Nut-Bolt as per IS:1363 and IS:1367 (galvanised steel), Insertion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in- charge.Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 194 6.3.1 Class PN 1.0 195 6.3.1.3 125 mm dia 196 6.3.1.4 150 mm dia 197 6.3.1.5 200 mm dia. 198 6.3.1.6 250 mm dia. 199 6.3.1.7 300 mm dia. 200 6.3.1.8 350 mm HW 201 PHED Revised BSR 20236.5 Providing, lowering, aligning, fixing in position and Jointing in pipe line, CI single Air Valve Flanged/Screwed type of approved makes for following pressure rating & dia complete, confirming to IS:14845-2000 (amended up to date) and of following specifications: Body, Cover and Cowl - Grey Cast Iron as per IS:210- FG 200, Float Stainless Steel AISI:304/IS:3444, Float Guide- HBT1, Body seat ring - Leaded tin bronze/SS, Seal ring and face ring - EPDM/NBR, Ends flanged according to IS:6418 or Screwed type shall have external pipe threads conforming to IS:554 Fasteners - CS Epoxy paint inside outside of food grade safe for drinking water,Valves including all material, labour, testing and commissioning as per Technical Specifications and as per direction of Engineer in charge.Note: Rates are exclusive of connecting tee, pipe piece and earth work. 202 6.5.1 Class PN 1.0 203 6.5.1.2 25 mm S-1 Type 204 6.5.1.3 40 mm S-1 Type 205 PHED Revised BSR 20236.17 Providing, lowering, laying, aligning, fixing in position and jointing CI dismantling joint (Suitable for Sluice valves etc.) as per IS specifications complete of the following sizes including all jointing material, cost of all labour, testing and commissioning Technical Specifications and as per direction of Engineer. Class PN 1.0 206 6.17.2 100 mm dia. 207 6.17.3 125 mm dia. 208 6.17.4 150 mm dia. 209 6.17.5 200 mm dia. 210 6.17.6 250 mm dia. 211 6.17.7 300 mm dia. 212 6.17.8 350 mm dia. 213 Road Crossing 214 PHED Revised BSR 2023 4.11 Supply laying and pushing of MS casing pipe of specified thickness approved by concerned department authority by trenchless method adopting any suitable technology below ground at required depth under running traffic condition as per Highway/ Railway standard including carrying out survey work at the job site for determining underground cable trenches like telephone, cable, water & sanitary lines and resistivity test for finding the soil strata using necessary equipments for completion of works, mobilizing of machineries and specialized crew at the job site complete in all respect, including excavation of driven pit and exit pit (up to 3 meter depth) with proper protection at these sites with shoring sheets and ISMB. Providing MS cutting edges for front shield and constructing thrust bed at designated level. Necessary dewatering and providing concrete foundation at the base of the driven pit, PVC/Rubber saddle as per the requirement of Highway/Railway authority, crane for handing of pipe and any other machinery, tools, and tackles required, construction of temporary works as per design, drawing and method asperapprovedby authority specification and the direction of the Engineer. Apply corrosion, resistant, protection on inside and outsideof casing pipeas per technical specification. 215 4.11.1 300 mm Dia 8 mm thick casing pipe. 216 Provision for Road Crossing permission and other charges for permission 217 PHED Revised BSR 2023 4.1 Earth work in excavation by mechanical means (Hydraulic Excavator)/manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr. including required all safety provisions etc.: All kinds of soil 218 PHED Revised BSR 20231.1 Providing, lowering, laying in trenches, aligning, fixing in position and jointingDuctile Iron (DI) ISI marked K-7 grade S&S pipes as per IS:8329-2000 (amended up to date), with internal cement mortar lining suitable for potable water with rubber ring (EPDM) joints as per IS: 5382-1985 including all taxes (Central and local), transportation and freight charges, inspection charges, loading/ unloading charges, including cost of labour and material, specials (Tee, bend etc.) satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer-in-charge. (excluding earth work) Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately. 219 1.1.1.3 150 mm 220 PHED Revised BSR 2023 9.1 Construction of RCC Sluice valve chamber for different type of valves including earthwork excavation, 100mm PCC M15 as leveling course, RCC M25 grade for base slab, side wall & cover slab, including cost of steel reinforcement, form work, Pre-cast, Plastic encapsulated CI/MS Foot Rest, MS flats for the support of pre-cast, proper curing of concrete work complete in all respect as per specifications and standard drawings and as directed by Engineer-in-Charge. 221 9.1.2 For Class-A loading 222 9.1.2.2 Sluice valve chamber of size1.17m x0.95m x1.415m for pipe size-from 125-to-150mm 223 PHED Revised BSR 2023 6.1 Providing,lowering, aligning,fixingin positionin pipeline,CID/FSluicevalvesstraight and pocket less body passage of approved make of following Pressure rating & dia complete, confirfing to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/ FG200Stem - SS 304 ,Body Seat ring, Wedge facing ring & Bushes - LTB2/ SS, Face to face dimensions as per IS 14846/2000 (amended up to date) ,Epoxy ( Non-Toxic- suitable for drinking water) applied inside and outside,Flanges Drilled as per IS 1538. Nut-Bolt confirming to IS:1363 and IS: 1367/ CS/ galvanised steelInsersion rubber of black EPDM 6mm thick . Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge. Note: Rates are exclusive of tail piece/ dismantling joints and earth work. 224 Manually Operated CI Sluice valve of Class PN-1.0 225 6.1.1.4 150 mm HW 226 PHED Revised BSR 2023 1.15 Providing and fixing of flanged/plain ended MS specials from MS sheet strips of relevant IS specification of approved thickness by welding , lowering, laying and aligning, fixing in position at all level/depths in trenches complete including all taxes, material , labour, inside lining, outside coating , testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in-charge 227 1.15.1 MS pipe special upto 600mm dia (with minimum 5.0 mm thickness sheet) 228 PHED Revised BSR 20236.17 Providing, lowering, laying, aligning, fixing in positionand jointing CI dismantling joint (Suitable for Sluice valves etc.) as per IS specifications complete of the following sizes including all jointing material, cost ofall labour, testing and commissioning Technical Specifications and as per directionof Engineer. Class PN 1.0 229 6.17.4 150 mm dia. 230 TOOLS-PLANTS & MISC. ITEMS 231 Tripod with Chain Pulley Blocks of 1 Ton capacity (6.0m legs) 232 Pipe wrench 10”, 14”, 18”, 24” and36” of ISI mark 233 Round files of sizes 8”, 10”, 12”, 14” & 16” (medium cut type) 234 Flat Files of sizes 8”, 10”, 12” (medium cut type) 235 Screw Driver set 236 12” and 18” Hacksaw Frame with 36 blades of ISI mark 237 Tong Tester, 1000 Amp 238 Pipe dye set ½” to 2” 239 Hammer of 200gm, 450gm, 1kg, 5kg & 20kg weight 240 Set of Ring spanners & Fixed spanners (covering all sizes) 241 Allen keys (As per plant and machines supplied) 242 De-watering pump set 243 Set of Tommy 244 Multi-meter (Digital) 245 AC 1.5 tone capacity with latest technology 246 Computor set complete latest version I-7 procesor 247 Lap top complete latest version I-7 procesor 248 Printer Black & white 3 in One advance technology 249 Printer Cloured 3 in One advance technology 250 Office Table 251 Officer Chair 252 Chair 253 Almirah 254 Water Cooler 255 Desert Coller 256 HOUSEHOLD CONNECTIONS 257 PHED Revised BSR 20231.26 Providing Household Tap Connection as per technicalspecification and approved drawing and as per relevant IS code (amended up to date) from HDPE pipe line up to consumer meter/premises by using electro fusion saddle piece (Complete job). This job includes digging out suitable size of pits and trench for laying service line in all kinds of soil; depositing and refilling of pit & jhiri with watering & ramming /compacting in layersand disposal of surplus excavated soil as directed with in a lead of 100 meter; providing & fixing of all fitting duly approved in accordance with specification for potable water including electrofusion saddle piece, gunmetal ferrule 4.0 mm, GM Full-way Valve (IS:778Mark) or wheel valve and specials, below ground level 20 mm nominal dia MDPE pipe PE 80 PN 16 as per ISO 4427/20 mm nominal dia PPR-C (Three layered) pipe PN16 SDR 7.4 (IS:15801:2008) (ISI mark) for and above ground level using 20 mm dia PPR-C pipe with standard PPR fittings/15mm dia GI pipes with fittings in the premises for fixing a tap/meter box (excluding), including accessories with flushing, cleaning, disinfecting and testing of pipe line complete required for making of service connection complete in all respect including labour charges. The service line should be laid at least 45 cm below ground level.Note: Road cut and restoration is not part of this itemand paid separately. 258 1.26.1 For connection with 20mm dia MDPE/PPR-C pipe length up to 05 mtr. 259 PHED Revised BSR 20231.29 P & F Bib cock (IS : 8931 mark), superior quality ofapproved make, chrome plated with complete brass body including brass handlewith wt. 300 to 325 gm.15 mm nominal bore. 260 PHED Revised BSR 20231.30 Road cutting for house hold service connection in minimum trench width wherever road crossing is required. Road cutting of cement concrete,WBM, Black top etc. of all thickness shall be done by using a concrete cutter machine keeping minimum trench width and restoration of the road with Cement concrete with PCC M-10 and CC M-30 grade as per specification and direction of Engineer in charge.. 261 PHED Revised BSR 20231.31 Add extra over item no 1.21, 1.22 & 1.23 for providing20 mm PE80 PN16asperISO4427MDPEpipeincludingexcavation,providing, laying & jointing of service line above 5.00 mtr.
|
