|
Tender For Supply, Installation, Testing And Commissioning Of Street Lights For The Sspcc Surrounding Area At Actrec; 1 STREET LIGHTINGSupply/replacement, testing & commissioning of external terminal box of size 200 x 250 x 150 mm made of 4 mm thick Cast Iron / PVC, neatly painted complete with front operable door with Allen key locking arrangement, arrangement for gland entry, water proof gasket, 4 Nos. of 8 mm dia. 40 mm long brass terminals on 150 x 30 x 10 mm bakelite strip, 16 A HRC fuse base & carrier with 6 A HRC fuse / 16A SP MCB, 16 A neutral link, nipple or sleeve of external dia. 38 mm which can be inserted in 38 mm dia. GI pipe, all as directed by O-I-C,ES. Equvilent arrangement can be done only after prior approval for make as well as other releted fixing/control gear arrangement. In case of replacement old/removed item shall be returned to E-I-C, ES. STREET LIGHT POLE ERECTION 2 7 Mtr. hot dip galvanised Octagonalstreet light pole with 1.5M long single arm bracket, suitable for 44 m/sec wind speed with suitable foundation bolts, bakelite with 1 no. 6A SP MCB and stud type terminal block/connector box of approved make suitable for terminating cable up to 4Cx16 sqmm size. 3 7 Mtr. hot dip galvanised Octagonal street light pole with hexagonal bracket suitable to mount integral flood light fixture & 1.5M double arm bracket suitable to mount two nos. of street light fixture.Suitable for 47 m/sec wind speed. (Fixtures can be mounted on the hexagonal bracket on six sides of the bracket but at max only 3 no. of integral flood lights can be mounted at a time.).with suitable foundation bolts, bakelite with 2 nos. 6A SP MCB and stud type terminal block/connector box of approved make suitable for terminating cable up to 4Cx16 sqmm size. 4 3 Mtr. hot dip galvanised Octagonal post top type pole having spigot on top of pole, suitable for 44 m/sec wind speed with foundation bolts, bakelite with 1 no. 6A SP MCB and stud type terminal block/connector box of approved make suitable for terminating cable up to 4Cx16 sqmm size. 5 Casting of new foundation for 7 Mtr. poles of above type inlcuding excavation of pole pit. The concrete mix for RCC foundation of Octagonal pole shall be M20. The scope shall also include grouting of foundation bolts including curing& provision of DWC HDPE pipe for passage the cable and finishing the surface. 6 Casting of new foundation for 3 Mtr. poles of above type inlcuding excavation of pole pit. The concrete mix for RCC foundation of Octagonal pole shall be M20. The scope shall also include grouting of foundation bolts including curing& provision of DWC HDPE pipe for passage the cable and finishing the surface. 7 LED street light fitting of following ratings having pressure die-cast aluminimum housing with Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint, suitable to following features. - Luminaires suitable with base plate and fitted on a existing site Pole.-In built electronic LEDdriver,-High Transmisivity diffuser>85%,-IP-65/67-High Efficacy,-Provide Uniform low glare lighting ,-CRI-70,-Warm White-Operating Temperature:--40 to +60 Celsius degree-Operatable voltage - 220-240 V,50 Hz, PF>0.9,-Colour Temperature-3000K. 8 90W, LED street light fitting, IP-67 outdoor type. 9 30W, LED Flood light fitting, IP-67 outdoor type 10 MV CABLE WORK Supply. Installation, testing & commissioning of 1.1 KV grade PVC insulated stranded/ round/ flat wire armoured Al conductor power cables ISI mark reputed makefixed on wall/ column/ ceiling or in shaft/ existing trench on 6 mm thick spacers/ angle support fixed with screws/ coach screws/ anchor fasteners, all other fixing accessories etc. as per instruction of Engg.-in-charge. 11 4 x 16 sq. mm Al conductor 12 3 x 2.5 sq. mm copper conductor cable 13 Supply, laying, testing & commissioning of LT cable through below ground through DWC pipe through out the campus as per requirment with all accessories and fixing arrangement all as per instructions & as directed by E-I-C, ES. 14 LT cable laying through DWC HDPE PIPEpipe 15 EXCAVATION THROUGH JCB OR MANUAL All cables to be laid in ground burial format. use JCB or manual diggingfor all types of soil, ground, roads, pavers etc. Direct burial of cables are not allowed. Scope covers:1)Excavation of ground up to a depth such that the top of the cable shall be minimum 900MM below the finished ground level. 2) After cable laying sand bidding to be done of 100mm thick and bricks to be provided. 4)Supply, Fixing, Painting & Sign writing of Route markerand Joint Indicators if any To prepare shop drawing and to take approval of consultant & client at each stage.8)To prepare & submit as-built drawing and handing over document to end user. To repair the road as existing after completion of excavation and backfillingworkExavation of all kind of soil as per required 900 mm below ground level including blasting & chiseling, using compressor, dewatering, back filling, reinstatement IIncluding bricks and sand , after work completion, if necessary disposal of excess earth within the radius of500 Mtrs etc, stacking of rocks at selected places as per instruction of EIC. 16 GI Earthing Strip Supplying & installation of tinned GI strip/ bare GI wire for earthing system fixed on wall/ side of the trench/ slab/ coloum/ beam along with clips/ saddle and spacers etc. including end connection with crimping type copper lugs complete in all respect, with continuty test etc & all as directed by Engg. -In-charge. 17 GI wire 8 SWG 18 Earthing rod for pole 1.5 mtr depth , 20mm Dia MS 19 Supplying & erecting crimping type copper lugs confirming to IS suitable for cables evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners. all as directed by O-I-C, ES 20 16 Sqmm Aluminium Lug
|
