|
Tender For Construction Of Public Distribution Shop Atward No.14 S F No: 1159(5,6) Moolathurai In Sirumugai Town Panchayat; 1 Dismantling RCC by manual / by using deployingmachineries 2 Dismantling Brick in cement mortar walls under3m high 3 Earth work excavation for foundation in all soils and sub soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation. 4 Supplying and filling foundation and basement well gravel filling sand layers not more than 15 cm thick, well rammed, watered and compacted complete complying with standard specification. 5 Plain Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge. 6 Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification 7 Random Rubble masonary in Cement Mortor 1:5 Mix (one cement, five sand)usingnewbest rough and bond stones from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. laying and curing etc. complete. complying with std.specifications. 8 Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best II Class Bricks of size9 ” x 4 3/8 “x 2 3/4 ”from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.(For 10 M3) 9 Supplying and fabrication of steel and placing in position of TMT steel rods for RCC works as per design given including cost of steel and GI binding wire in all floors etc., complete complying with standard specification in TNDSS NO:97 V,VI (S6) VII (S6), VII-3. 10 Supplying and Erecting centering for sides and soffits including necessary supports and strutting upto 3.29m height for plane surface in all floors with all cross bracing using mild steel sheets of size 90x60cm and 10 gauge stiffened, welded with steel angle of size 25x25x3 mm for boarding laid over silver oak joists (Country wood) of size 10x6.5cm spaced @ about 90cm c/c and supported by casurina props of 10-13cm dia spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10Sqm for the following items (RCC floor slab, roof slab, Rectangular/Square, tee/All beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc. A ) Column 11 B ) Grade Beam 12 C) Slab and Beam 13 Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - 14 Finishing the top of flooring with granolethic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete 15 Plastering with cement mortar 1:5 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309) 16 Plastering with CM 1 : 5, 12mm thick over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. 17 Plastering with CM 1 : 3, 10mm thick over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. 18 Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification 19 Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2. 20 Flooring with Cuddapah slabs of 40mm thick over a base mortar in CM 1:3 (One Cement and Three Plastering Sand (P - Sand))20 mm thick and pointed with cement mortar 1:3 ( one cement and three Plastering sand)usimg Black oxide complying with standard specification(P & D data 53 21 Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8"0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete. 22 Supplying and fixing in position of M.S grills using for windows and ventilators in positionincluding labour charges for fixing furniture fittingsfor windows & ventilatorswith standard drawings , etc., complete complying with standard specifications. 23 Wiring with 2x1.5(22/0.3) sqmm PVC unsheathed SC Copper conductor of 1100 V gradein suitable PVC rigid pipe on wall and ceiling with PVC accessories and with T.W. switch box with 5amps F.T. switch in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wireconnection of 14 SWG wire for cocealed Light point/fan point (5 points per coil) [ SD No. 25 ] 24 Wiring with 2 x 1.5 sqm(22/0.3) insuheathedSc Cu Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and celing with PVC accessories with TW switch box and 5A F.T switch in flush with wall150 x 100 x 113 mm TW switch Box for 5A 3 pin non inter locking CS plug with continous earth wire connection of 14 SWG T.C wire and making good of the concealed portion with suitable colour for concealed PVC plug point (SD 37) 25 Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V)32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm withsupporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank onwall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit[SD125 ] 26 Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade on7/20 GI bearer wire for service connection mains [SD 64] 27 Supply and fixing of 15Amps arial fuse unit (500amps) on suitable 100X100mm teak wood concealed box with hylum sheet on the tapping pole with necessary clamps [ SD No 130] 28 Supply and fixing of single box type 4"-40Wflourescent tube fitting with copper choke and condenser with TWround block on wall or ceiling with flourescent tube with PVC unsheathedcopper leads from terminals to the fitting ofTube Light [SD88] 29 Supplyingand fixing of W T Bulk head fitting with guard (Philips/bajaj/crompton/Klite) suitable for incandescent lamp and 90W LED bulb . [SI 84] 30 Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with "P" trap or "S" trap confirming to IS:2556 -Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.
|
