|
Tender For Additional / Alternator To Qtr Of Bi Line Under Ge East Jrc; 1 Demolition of cement concrete of any description and in any position and removing surplus spoil out of defence landwhere directed at a level not exc 1.5 m above the starting point all as specified and directed 2 M&L for 50mm PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth without using extra cement all as specified 3 Demoliation floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified 4 M&L for non skid joint free glazed ceramic coloured tiles ofarea of eachtile exceeding 0.11 sqm but not exceeding 0.18 sqm and 6-7 mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed. 5 M&L for non-skid coloured ceramic glazed tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed. 6 All as per item No 05 above but on skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:4) complete all as specified. 7 Roughering surface of old concrete floor or wall by picking, sweeping clean and washing down with water to remove dust including brushing neat cement slurry with 3.00 Kg/Sq mtr of Cement etc complete all as specified and directed . 8 M&L for coloured glazed tiles of size 450x350x7mm thick as in vertical surface i.e. skirting/dado set and jointing in neat cement slury and pointedin white or coloured cement to match the existing surface with & including rendering 10mm thick in cement morter 1:4 finished rough to fix tiles , complete all as specified and directed . 9 Demolition and dismantling of reinforced cement concrete of any description and in postiion not other wise specifically provided for complete all as specified and directed . 10 M&L for MS TMT bars 10 mm dia and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for column hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia. complete all as specified and directed . 11 Material and labour for PCC (1:2:4) type B-1 using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 12 M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed . 13 S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Boardof required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For Kitchen Cabinets.complete all as specified and directed . 14 S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) One side Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For Kitchen Cabinets. complete all as specified and directed . 15 S & FContinuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30mm complete all as specified and as directed. 16 S&F stainless steel soft close hydraulic clip on concealed hinges for full overlay (0 degree crank ) for kitchen cupboard ,complete all as specified and directed. 17 S & F 75mm Extruded aluminium alloy handles, fabricated type,anodised, complete all as specified and directed. 18 M&L for 16-18mm thick pre-polished green marble as in cooking plateform over 15mm thick screed bed in CM (1:6) including grinding and mirror polished/granite polished and making hole for LPG pipe and rounding of edge of stone , complete all as specified and directed. 19 Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc and removing surplus spoil out of Defence Landwhere directed at a level not exc 1.5 m above the starting point complete all as specified and directed . 20 M&L 15 mm thick cement plaster in cement mortar 1:6 on internal surface of brick or concrete surface finished even and smooth withoutusing extra cementall as specified 21 M&L for preparing new surfaces plastered or unplastered surfaces of walls by applying two coats of oil bound distemperover a coat of primer over a coat of 1 mm avg thickness wall putty complete all as specified and directed . 22 Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coat of distemper oil emulsion over a coat of primer over 1mm avg thickness wall putty complete all as specified. 23 Material and labour for 15mm thick cement plaster on brick or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound in the proportion recommended by manufacturer, surfaces finished fair and even complete all as specified and directed. (WPC shall be measured and paid separately under appropriate item of this BOQ).complete all as specified and directed . 24 Material & Labour for complete removal of existing treatment of old decorated Wall surface including scraping down smoke soot, moulds , moss & efflorecent salts of acrylic exterior emulsion paint (weathercoat) two coat over a coat of wall primer complete all as manufacturrer"s instructions complete all as speicfied and directed. 25 Material & Labour for new plastered surface of walls surface including scrapind down smoke soot, moulds , moss & efflorecent salts of acrylic exterior emulsion paint (weathercoat) two coats over a coat of wall primer complete all as manufacturrer"s instructions complete all as speicfied and directed. 26 M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement all as specified. 27 Dismantiling of concrete by chiselling from RCC members like col, beam parapet, facia, chajja, ceiling etc exposing the reinforcement without disturbing the reinforcement and primed with using Araldite epoxy resins manufactured by M/s ciba Geigy Ltd/ FAIR BOND EP/Sika or other approved manufacture and providing doubing coat of 20mm thick in CM 1:3 including necessary form work and reinforced with chicken wire mesh where reqd and rendering 15mm thick in cement mortar 1:3 at any height, complete all as specified and directed. 28 M&L for three coats of white wash on newly plastered surfaces ofceiling includingpreparation of ceilingsurfaces complete all as specified and directed by Engr-in-charge. 29 M & L for preparation of old decorated plastered or unplastered surfaces and apply two coat of white wash to matching with new wall surface including cornicescompleted all as specified and directed 30 M&L precast ferro cement shelves 25mm thick fixed over angle iron 25x25x5mm frame fixed to walland necessary groves cutting to wall and making good by cement plaster (1:1) to match the surfaces, including necessary form work and reinforcement etc complete work for shelves, platform , cub board shelves etc all as specified and directed. 31 M &L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:-(i) Application of Two component acrylic modified cementitious coating(aa)The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cementlaitance, existing coating and achieve a gripping profile that is clean, dry and free from laitance and dry other form of surface contamination. The installation instructions in manufacture"s published literature should be strictly complied with, including but not limited to the following:-(bb)Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR latex/ Perma latex SBR/FOSROC Nitabond SBR latex/Asian paint latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc)Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO. (dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified cementitious coating of SIKA Top Seal-107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer"s instructions.(ee)Apply glass fabric sheet of SIKA Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet.(ff) Once touch dry, apply second coat of Acrylic modified cementitious coating of SIKA Top Seal -107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer"s instructions on the entire area. (gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat.(hh)The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surfaces. (jj) It is essential to cure Acrylic modified cementitious coating immediately after application (minimum 6-8hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking.(kk)A protection plaster 12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with SIKA Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645.(ll)All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of Make SIKA Seal Tape/FOSROC/Dr Fixit/STP. (mm) The membrane has to be protected in accordance with the manufacturer"s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer"s recommendations.(nn) Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturer"s and approved by GE. (ii)All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealent. (iii) All CI traps in sunken slab to be enclosed with PCC 1:1.5:3 (Min15cm) all around. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long )including cutting to existing wall and making good the disturbed surface complete all as specified and directed.(vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note:-Item No(iv) ,(v) &(vi) shall be measured and paid seprately. 32 M & L Cement concrete1:5:10 type E-2 (using 40mm stone aggregate) as in sunken flooring complete all as specified. 33 S & F drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long )including cutting to existing wall and making good the disturbed surface complete all as specified and directed. 34 M & L 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. 35 S&F in repairs Vitreous china wash down water closet pan (padestal pattern), white (excluding fixing bolts,flushing cistern) incl seat cover and flushung pipe for pedestal pipe etc. 36 S&F chromium plated brass JET including PVC pipe connection fixed to EWCall as specified and directed. 37 S&F CP grating 125mm diaall as specified and directed by Engr-in-Charge 38 S&F in repair, CP soap dish holder and fixed to wooden plugs with chrominum plated brass screws and cup washers, complete all as specified and as directed. 39 M&L Galvanised iron water tubing 15 mm bore, medium grade with & including all fittings fixed to wall, ceilings andor laid in floors etc including taking down the existing tubing complete all as specified. 40 M&L Galvanised iron water tubing 20 mm bore, medium grade with & including all fittings fixed to wall, ceilings andor laid in floors etc including taking down the existing tubing complete all as specified. 41 S&F PVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle, 10 ltr capacity including brakets fixed in repairs complete all as specified and directed . 42 S&F Vitreous china wash hand basin , white, flat back 550x400mm including one number brass CP waste coupling ,32mm dia , PVC waste pipe with connector , brackets 2 nos including cutting for and pinning in ends of bracketscomplete all as specified. 43 S&F in repair single lever basin mixer with popup waste, suitable for fixing to 15mm bore (dia) GI pipe, complete as all specified and as directed. 44 S&F in repair single lever sink mixer swinging sput (wall mounted) with conneting legs and wall ganges suitable for fixing to 15mm bore GI Pipe, complete all as specified and directed. 45 S&F PVC connection , reinforced 45cm long 15mm in size with brass check nut and PVC washers at both ends complete all as specified and directed . 46 S&F 15mm stop valves, (Concealed type) fancy type chromium plated with long shank and cup screwed down, high pressure with crutch or butter fly handlescrewed at two right angles endsfor both iron pipe or for unionsand fixed in repairs .complete all as specified and directed . 47 S&F 15 mm Angle/stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handlescrewed both endsforiron pipe or for unionsand fixed in repairs complete all as specified and directed . 48 S&Fsinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers, waste coupling and waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 x 160 mm including bedding in CM on dwarf wall or incl fitting contilever brackets and conection union topipe complete all as specified and directed . 49 S&F Bib tap cast copper alloy , chromium plated suitable for 15mm bore iron pipe with long body fancy typecomplete fixed in repairs complete all as specified and directed . 50 S&F brass chromium plated shower rose of 125mm size, with or without swivel joints includingfixing to steel pipeor union in repairs complete all as specified and directed . 51 S&F brass chromium plated tubular towel rail 20 mm dia , D type 60 cm long between CP flangescomplete all as specified and directed . 52 S&F in repair Stainless steel kitchen plate rack of superior quality size 31" x 36" 10" and fixed to wooden plug with chromium plated brass screws and cup washers all as specified and directed 53 M&L for chromium plated peg set of 5(PTMT), fixed with screws and plugging to rear side of door shutter in bath, complete all as specified and directed. 54 S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller platewelded to steel frame/ screwed to wooden frame complete all as specified and directed. 55 S&F for corner glass shelf 300mm (with brass brackets) and fixed to wooden plug with chromium plated brass screw and cup washers, sample approved by Engr -in-charge all as specifed and directed. 56 S&F in repair fancy Wall Mixer 3-in-1 with provision for both Over Head Shower and Hand Shower complete with 115mm long bend Pipe, connecting legs & wall flange of makes of Make Jaquar Cat No FLR-5281N or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. 57 S&F in Repairs 600mmx450mm bevelled edge mirror of selectedquality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed . 58 S&F WHB glass Shelf600 mm long and 125 mm wideas per sample approved by Engr -in-charge complete all as specifed and directed. 59 M&L for mild steel pipe 25 mm dia curtain rod with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade as approved by GE all as specified. Fixed in repair complete all as specified and directed . 60 S & F20mm diacurtain rails , mild steel , chromium plated fixing in cup board with brackets, stops, rollers etc, complete all as specified and directed . 61 Taking down chowkats or frame not exc. 1.5 sq m each with shutters (without taking off shutters from the fames) complete all as specified and directed . 62 Taking down chowkats or frameexc. 1.5 sq m but n.exc 4 sq m each with shutters (without taking off shutters from the fames) complete all as specified and directed . 63 Taking down shutters of any description exc. 1 Sqm and n. exc. 2 sqm complete all as specified and directed. 64 M&L for MS work as in hold fast and similar small articles complete all as specified. 65 S & F for Pressed steel frames size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified. 66 S & F for Pressed steel frames size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified. 67 S&F for 40mm thickness of factory made flush shutter solid core construction with particle board & ply wood face panels, one face with decorative face veneer with lipping/ frame to match, commercial type on both side including 40 x 6 thick 2nd class Hard wood lipping on edge, complete all as specified and directed. 68 S&F 2ndtype hard wood35mm thickness of factory made plain framed, panelled shutter with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated. complete all as specified and directed . 69 S&F for 2nd class hard wood 35 mm thickglazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I, sector 8, clause 8.20 (a) complete all as specified and directed . 70 S&F butt hinges medium weight, cold rolled mild steel100 mm size complete all as specified and directed . 71 S&F 300 mm long mild steel sliding door bolts stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and twoon staple plate complete all as specified. 72 S&F Mild steelpressed handles oval type stove enamelled black 150 mm size complete all as specified and directed . 73 S&F Mild steel barrel tower bolts, 200mm long, stove enamelled black, with bright bolt. complete all as specified and directed . 74 S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor overall length of cover plate 75mm complete all as specified and directed. 75 S&F cast iron floor trap with grating including jointing to waste pipe in run lead joint fixed in cement concrete type (1:2:4) type B-1 diameter of outlet 75mm, complete all as specified and directed. 76 M&L 75mm PVC (SWR)PVC (SWR) floor trap, plain with grating including jointing with solvent cementfixed in repairs complete all as specified and directed. 77 M&L 75mm PVC (SWR)PVC (SWR) gully trap, 125 mm, setting and jointing with solvent cement complete all as specified and directed. 78 M&L for salt glazed stonewere gully traps, square or round mouthed 150 x 150 mm size type "P" including cast iron cover grating and setting and jointing to drain pipe in Cement Mortar 1:1 complete all as specified and directed. 79 S&F magic eye brass best quality fixed inmain door shutter approved by Engineer in charge complete all as specified and directed 80 S&F PVC solid door frame of size 50mm x 47mm made out of 5 mm printed wood grain and edges painted to be matched with shutter, reinforced with MS square tube, as per specification and drawing in SSR Part-II complete all as specified and directed . 81 S&Ffactory made solid panel PVC Door30mm thick (style) consisiting of frame made out ofM.S.Tubes for top & bottom rails M.S. frame shall be covered with heat moulded printed wood grain and edges paintedPVC `C" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour 10mm thick PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 10 mm thick PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame at the site as per specification & drawing.complete all as specified and directed . 82 S&F butt hinges medium weight,Stainless steel , bright polished 100 mm size for fixing PVC Door Shutter complete all as specified and directed . 83 S&F for Aluminiumhandles125 mm size fixed with screws all as specified 84 S&F for Aluminium tower bolts, 150mm long fixed withscrew all as specified and directed 85 S & F20mm thick factory made PVC flush cupboard shutter with frame consisting of panel of hollow section thickness consisting of frame made out of M.S. tubes of 19 gauges thickness and size of 19mm x 19mm inserted inside the hollow section of stiles, top and bottom rails and two 19mm x 19mm MS tubes inserted horizontally inside the hallow profile section at an equal distance from top and bottom of door and fixed with hollow profile section using 5mm thick PVC sheet using screws hollow PVC profiles shall be lipped with 10mm (5mm x 2) thick x 20mm) width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof water proof and fire retardant prelam PVC sheet using solvent cement on both sides of the panel etc complete all as specified and directed. 86 S & F Hasp & Staple aluminium 100 mm , including bolt to hinge plate and fixed with screws with Cup Board shutter, complete all as specified and directed . 87 Supply and fixing Aluminium anodised powder coated Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed with 5mm thick tinted glass & one no. s/s wire mesh panels) upto 1.50m height made of (big series) frame 100 x 45 mm & sash 46 x 62 mm both having wall thickness of 1.5 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced galvanized mild steel section made from roll forming process of required length (shape & size according to aluminium section), appropriate dimension of extruded glazing beads andextruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. 88 S & F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars barallel iron doors and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed . 89 S&F for galvanised mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed with tinned tacks complete all as specified and directed . 90 Dismantlingof brick tiles single layer as in roofcovering complete all as specified 91 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof) removing surplus spoil out of Defence Landwhere directed at a level not exc 1.5 m above the starting point all as specified. 92 M&L for PCC (1:2:4) typeB-0 (using 12.5 mm graded stone aggregate) as in benching, roof padding,roof kerbs or mud stops, coping etc rounded or chamfered on edges. complete all as specified and directed . 93 Cleaning the surface and made free of dirt, foreign particle, laitance followed by grinding all all protrusion to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expiation contraction. Cutting the grooves with suitable cutter machine in V groove filled with repairs mortar/ microconcrate / general purpose grout as recommended proportionally as per recommendation of manufacture. Making of Gollas at all the corners with polymer modified mortar (1:4) cement sand with 3.5% acylic of cement weight. Make: STP/Asian Paints/Sikka complete all as specified and directed . 94 M&L for 10 mm thickcement plaster in cement mortar 1:4with water proofing compound asper manufacturer"s instructions to brick or concretesurface finished even and smooth without using extra cement and using waterproofingcompound all as specified (WPCshall be measured and paid separately) complete all as specified and directed . 95 Supply and applying high build elastomeric waterproofing coating based on pure hydrophobic polyurethane cold appliId of spray/brush applied, membrane with an elongation of 280% and tensile strength of 2.7N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88% solid content. The system includes final base preparation, epoxy primer 1:1 (Resin; harder) application with 100% water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 kg per Sqm. Application should be done with Graco sprayer by a company authorised applicator ” of given. Make: STP/Asian Paints/Sikka complete all as specified and directed . 96 Demolition of brick work as in walls/parapet wall,s removing grass fungus weed, roots of trees completely, grown on roof/wall surfaces, complete all as specified and directed. 97 Brick work with sub class "B" bricks straight or curved on plan exc 6m mean radius built in CM 1:6complete all as specified and directed . 98 All as perItem No 97 above but except bricks complete all as specified and directed . 99 S&F 500 ltr rotational moulded polythylene water storage tank (Cylindrical vertical with closedtop) hosted and fixed in position incl dismantling of existing tank of any description complete all as specified.ISI marked. 100 S&F 20mmdia Ball valves high pressure of PTMT with epoxy coated Aluminiumrod& highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight-210gms.) complete all as specified and directed . 101 S&F for 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 102 M&L for preparation of newwood or wood based surfaces of any description, not otherwise described over 10cm width or girth and applied two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engr-in-charge. 103 M&L for preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applied two coat of synthetic enamel paint over one coat of red oxidezinc chrome primer complete all as specified and directed by Engr-in-charge. 104 S&F PVC (SWR) pipes with single socketed in any length with rubber ring joints fixed on brick walls 110 mm dia including demolition and braking up existing pipes complete all as specified and directed. 105 S&F PVC (SWR) bends in radius 110 mm bore complete all as specified and directed . 106 S&FPVC (SWR) junction single, (Single T) equal or unequal in radius 110 mm borecomplete all as specified and directed . 107 S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed . 108 S&F 75 mm bore PVCpipes single socketed in any length with rubber ring joints ixed to walls or laid in floor, including demolition and braking up existing pipes complete all as specified and directed. 109 S&F75 mm dia PVC (SWR ) bends any radius complete all as specified and as directed. 110 S&F75mm dia PVC (SWR ) junction single, (Single T) equal or unequal with rubber rings ljoits fixed to walls complete all as specified and as directed. 111 S&F75mm dia PVC (SWR ) vent cowl complete all as specified and as directed. 112 Surface excavation n exc 30cm deep and averaging 15cm deep in soft/loose soil all as specified and directed. 113 Materials and labour for broken stone or boulder hard core of gauge n.exc, 63mm deposited spread and leveled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified and directed. 114 M&L Cement concrete type C-2, 1:3:6( 20 mm grade agg) 100 mm thick as in sub base of flooring all as specified and directed. 115 M & L 30mm sand cushion, filling under floors or in foundations including watering and consolidation all as specified and directed. 116 M & L for laying 60 mm thick machine pressed precast concrete interlocking paver block and shape and size conforming to IS -15658-2006 of M-35Grade with grey cement andpigment complete all as specified and directed.NOTE: The sample shall be got approved from the GE before buld procurement and lots shall be got tested independtly by the GE. 117 M&L PCC (1;2:4) type B-1 using 20mm graded stone agregete as in sides of rounded or chamfered on edges of interlocking tiles complete all as specified and directed. 118 Material and labour for 18-20mm thick machine cut Kota stone slab in single peice size in Steps/Riser & landings of stair cases including bull nose edge, flooring, jointed with grey cement mixed with pigment to match the shade of the slab including grinding, rubbing and polishing to mirror finish with & including screed bed or bedding layer of mortar 15mm thick in cement mortar (1:6) for laying floor finishes including neat cement slurry with 3 Kg/ Sqm complete all as specified and directed 119 Demolition and breaking up drain pipes any dia of bore (SGSW, AC or reinforced concrete) pipe set in cement mortar complete all as specified 120 Earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m,for any type of soil as directed by Engineer incharge. 121 ditto as above but depth exc 1.5 m upto 3.00 mtr.complete all as specified and directed . 122 ditto as per item No 118 , but depth exc 3.00 m upto 4.50 mtr. complete all as specified and directed . 123 M& L for reinforced concrete pipes,class NP3, laid and jointed complete with collars 200 mm bore laid in trenches and jointed complete all as specified. 124 M& L for reinforced concrete pipes,class NP3, laid and jointed complete with collars 300 mm bore laid in trenches and jointed complete all as specified. 125 M&L cement concrete type D2 1:4:8 (40 mm grade aggregate)as in concrete bed to drain pipes 200mm internal dia incl paking under and haunching againstthe pipe sides of pipe after they are and tested all as specified. 126 M&L cement concrete type D2 1:4:8 (40 mm grade aggregate)as in concrete bed to drain pipes 300mm internal dia incl paking under and haunching againstthe pipe sides of pipe after they are and tested all as specified. 127 Demolition of brick work built in cement mortar incl all quoins, arches, pillar etc complete all as specified. 128 M&L for brick work with sub class "B" bricks straight or curved on plan exc 6 M mean radius built in CM 1:4all as specified and directed by Engr-in-charge. 129 M&L providing cement concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in fdns, filling and mass concrete complete all as specified and as directed. 130 M&L for 12 mm thickcement plaster in cement mortar 1:4with water proofing compound asper manufacturer"s instructions to brick or concretesurface finished even and smooth without using extra cement and using waterproofingcompound all as specified (WPCshall be measured and paid separately) 131 Supply onlyintegral water proofing compound complete all as specified and directed . 132 Extra for formingfair finished drain or channel 30cm inner girth in cementconcrete, using extra cement, includingforms, moulds, mitred/stopped ends etc complete all as specified and directed . 133 M&L for PCC (1:2:4) typeB-1(using 20 mm graded stone aggregate) as in cills, PCC blocks, coping,benching, water troughs, seismic and other similar bands, plinth bend, etc including weathering slightly rounded or chamfered angles and throuting , including necessary form work etc all as specified. 134 M&L for precast cement concrete type B-11:2:4 (20mm graded aggregate) and set in Cement Mortar (1:4) as in landings, manholes cover slabs, chajjas, shelves and similar articlesincluding necessary form work all as specified and directed. 135 M&L for MS TMT bars 10 mm and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for clos hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia.complete all as specified and directed . 136 Cutting into existing manholes for connecting new drains or sewage line making good to pipe and rendering ,cuttingout existing benchingforand formingbranch channel in cementconcrete 1:2:4 type B1 smooth finishedand reformingbenchingas required internal dia of pipe in 150mm complete all as specified and directed . 137 M&L mild steel work assmall articles for handles, holdfasts, steps, rungs, etcknee piece and similar small article complete all as specified. 138 S&F for flexible PVC Waste pipe of approved quality 32 bore, 75 cm long with one end socketed fixed to waste coupling, compete all as specified and directed 139 M&L for brushing neat cement slurry with 3 kg of cement per sqm compete all as specified and directed 140 M&L for bitumen primer shall be applied on plastered surface of roofs at rate of 0.40 Kg/Sqm of surface area of roof for use in water proofing and dump proofing treatment compete all as specified and directed. 141 M&L for painting the roof surface with a coat of hot blown paving industrial bitumen 85/25 as a bonding material in two coats one on primed surface & 2nd on APP based polymeric membrane at the rate of 1.20Kg/Sqm complete all as specified. 142 M&L for APP based polymeric membrane minimum weighing 3 Kg/ Sqm and minimum 3mm thick reinforced with five layer polyester non-woven fabric (wt not less than 150gms/sqm) laid on primed surface by forced application complete all as specified. 143 M&L for 40mm thick brick tiles with 15mm thick screed bedded layer 1:3 CM laid on bitumen coated surface and joints grouted flush morter 1:3 mixed with 5% crude oil by weight of cement, compete all as specified and directed 144 All as per srl item No. 143 above but except brick tiles and complete all as specified. 145 M&L for cutting out cracks to V-section in existing RCC roof slabs or terracing, cleaning out & filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight ) compete all as specified and directed 146 M&L for flush pointing in CM 1:3 on brick tiles laid flat including racking out joints/pointing, hacking for key, scrubbing down with watercompete all as specified and directed. 147 Taking down carefully existing point wiring of any type/ any size (ie on wooden/ batten, surface conduit, casing capping or concealed conduit) complete for light, fan, socket or power point etc includingremoving switches, sockets, holders, ceiling rose, pendants, regulators, light fittings, switch board outlets with sheet taking credit of unserviceable items, light as per Sch of credit, depositing serviceable items to MES store for refixing at site under relelvant items and making good disturbed surface of walls,roof, floors etc. with any type of civil wk involved complete all as specified and directed. 148 M&L for point wiring for light/fan point with 1.5 Sqmm (nominal area) FRLS PVCinsulated unsheathedmulti stranded copper conductor of size 1.5 Sqmm cabledrawn in and including concealed rigid PVC conduit medium grade not less than 20mm dia with accessories including cutting chases for laying of conduit /fixing of boxes in walls/floor and terminated in and incl sunken pressed steel boxes duly painted with anti corrosive paint over a coat of red oxide primer with plastic laminated bakelite sheet top cover 3mm thick fixed with nickel polished screws with cupwashers etc including FRLS PVC insulated unsheathed multi stranded copper conductor 1.5 Sqmm single core as earth continuity conductor (green colour) connected with earth dolly with thimble etc including making good to disturbed surfaces as per adjoining specification complete all as specified and as directed by Engr-in-Charge. 149 All as per srl item No. 148 here in before but for one socket outlet 5 Amps on independent board complete all as specified. 150 All as per srl item No. 148 here in before but for one socket outlet 5 Amps on the sameboard controlled complete all as specified. 151 All as per srl item No.148 here in before but for one bell point controlled by one bell push complete all as specified. 152 All as per srl item No. 148 here in before but for one light point controlled by two way switches complete all as specified. 153 S&F switch piano flush type, 6 Amps, 240 Volt AC single pole, two way complete all as specified. 154 All as per srl item No. 148 here in before but with 2.5 Sqmm(nominal area) FRLS copper cable for one 3 Pin 15 Amp socket on independent board including one 2.5 Sqmm copper conductor multi stranded green colour PVC insulated unsheathedFRLS cable 1100 volts grade as earth wire connected to common earth and earth dolly with all accessories complete all as specified and directed by Engineer-in-Charge. 155 S&F switch piano flush type, 5 Amps, 240 Volt AC single pole, one way complete all as specified. 156 S&F switch piano flush type, 15 Amps, 240 Volt AC single pole, one way complete all as specified. 157 S&F socket out let 5 Amp, 5 pinflush type complete all as specified. 158 S&F Socket outlet multi purpose 2 in 1, 5/6 pin, 5 & 15 Amps, flush type complete all as specified. 159 Supply and fix Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one SP MCB 20 Amps including top Plug complete all as specified & directed by Engineer-in- charge .(For geyser = 24 Nos, For AC = 24 Nos) 160 S&Fin repairDecorative wall mounting light fitting suitable for 09 watt LED lampcomplete with Polycarbonate cover/ glass shade including 1 x 09watt LED lamp complete all as specified. 161 S&F ceiling rose surface type bakelite 65 x 50mm three terminal complete all as specified. 162 M&L in replacement Bell electric AC (Ding Dong) 240 volt SP complete all as specified. 163 M&L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittingsall as specified and directed. 164 S&Ffive step fan regulator, electronic type, single phase,including connection complete all as specified. 165 M&L forsub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 4.0 Sqmm drawn through in and including PVC rigid non metallic conduit(medium grade ISI marked) with all fittings including earth continuity FRLS PVC insulated unsheathed multistranded copper conductor cable 4.0 Sqmm PVC insulated with green insulation complete all as specified.NOTE:Two run of 4.0 sqmm wire and one run of4.0 sqmm wireas earth wire includingPVC conduit shall be measured as one unit. complete all as specified and directed . 166 M&L in replacement of sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of6 Sqmm drawn through in and including PVC rigidnon metallic conduit(medium grade ISI marked) with all fittings including earth continuity FRLS PVC insulated unsheathed multistranded copper conductor cable 6 Sqmm PVC insulated with green insulation complete all as specified. NOTE:Two run of 6 sqmm wire and one run of 6 sqmm wireas earth wire includingPVC conduit shall be measured as one unit. 167 M&L in replacement for sheet metal DB for MCBs, SPN 12 ways, double door,single phase, with bus bar, neutral bar/ connectors suitable copper thimbles, lugs etc complete all as specified. 168 Supply & FixMCB SP 6 to 32 Amps, 10 KA, B curve all as specified and directed by Engr-in-charge. 169 Supply & FixMCB SPN 40 to 63 Amps, 10 KA, B curveall as specified and directed by Engr-in-charge. 170 Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including tube light rod 20 watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose completecomplete all as specified & directed by Engineer-in- charge. 171 Supply and fixing LED light fittingwith high out put diffuser, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete 172 S & F LED light fitting 1 x 9/10 W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 173 S & F energy saving & environmental friendly long life versatile pressure die-cast aluminium housing luminaire with heat resistant glass/ polycarbonate cover and suitable optics for uniform distribution of light 35 watt LED for bldg security lights with high efficiency electronic driver BIS approved, having IP-66 protection,surge protection operative on AC supply 170 volts to 270 volts pre-wired complete with GI pipe of 25mm bore and MS clamp duly painted with two coat paint all as specified and directed. 174 Taking down carefully of ceilingfan of any sweep or make with dismantling blades allas specified and directed by Engineer-in Charge. 175 Painting of ceilingfans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc 176 Hanging of ceiling fan andconnectingup including provision of cable from ceiling rose or connector to fan all as specified and directed by engineer in-charge 177 Earthing completein replacementwith galvanised steel earth plate electrode 60cmx60cmx6.0mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level with the top edge of electrode not less than 1.5 metres below normal ground levelconnected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and incl GI lead protection pipe of GI light grade 15mm dia upto 7.5 mtrs and watering pipe 20mm bore of GI medium grade with funnel and wiremesh, earth plate covered on all sides with min 150mm thick alternate layers of charcoal, saltall as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthingpoint with PCC chamber and RCC cover in 1:2:4 complete with any type of earth work involved.all as specified and directed and testing on completion. Note:- PCC Chamber shall be constructed at least 0.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner. 178 Supply and fix exhaust fan, steel body AC single Phase230V of size 300mm sweep (heavy duty) with blades, frame and louvers (louvers made of powder coated CRCA sheet frame and having aluminium/GI sheet flappers) completeincluding making/ cutting of hole in wall of any thickness and making good to disturbed surface complete incl plastering all as specified and directed. 179 Supply and fix exhaust fan, Metal body AC single Phase. 230V of size 225/230 mm sweep with blades, frame and louvers completeincluding making/ cutting of hole in wall of any thickness and making good to disturbed surface complete incl plastering all as specified and directed. 180 M & L for cutting hole suitable for exhaust fan 230mm / 300mm sweep and repair the wall with necessary cement work, plastering to make required the disturbed surface to match with existing specificatios complete all as specified and directed. 181 M&L for taking down carefully Exhaust Fan of any sweep or make, painting of fans complete (as per previous colour) with synthetic enamel paint by spraying, cleaning all dust etc including replacement of flexible wire,bolts all as specified and directed. 182 M&L for Re-fixing Exhaust Fan of any sweep duly greasing and minor repair work complete all as specified and directed. 183 Supply and fixBell push, flush type,5 amp all as specified and directed 184 Material and labour for boring hole under the road/pavement/hard standing with the help of trenchless technology using ultra sound technique and necessary machine for inserting HDPE pipe 80mm SN8 having suitable working pressure not less than one meter below ground level complete all as specified and directed by Engineer-in-charge. 185 Fixing only serviceable tube light fittings any type and any description obtained from item no 147, including necessary electric connection with round flexible wire with multi stranded copper conductor of size 0.50 sqmm, 3 core, 1100 volts grade completeall as directed. 186 M&L for taking down Geyser of any capacity or model after disconnecting all water supply and electric connections complete all as specified and directed. 187 Fixing only Geyser of any capacity or model installing with new fastner, connectingall water and and electric supply connections testing and commissioning complete all as specified. 188 Supply and fixing electric water heater vertical type, storage type with steel body (outer), suitable inner tank & heater and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated with temp control knob complete with all accessories such as safety valve, thermostat, NRV etc. complete all as specified and directed.Make: RACOLD/ AO SMITH/ VENUS/ MORPHY RICHARDS/HAVELLS/ CROMPTON 189 Supply and fix heavy duty hot and cold flexible pipe with both side flair nut for 20 mm and 450mm long connecting with GI pipe complete all as specified and directed. 190 Supply, laying and testing cable in replacement, XLPE insulated , PVC sheathed, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 corecomplete laid in trenches/ through pipes/ under road/ along wall complete all as specified & directed. 191 Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and gettingout complete all as specifiedand directed by Engineer-in-Charge. 192 Returing, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25 cms thick each layer complete all as specified and directed by Engineer-in-Charge. 193 Removal of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point completeall as specified and directed by Engr-in-charge. 194 Material and labour for sand cushioning with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable andtrenchespunned down to thickness of 18 cm completeall as specified and directed.(Note: Punned thickness of 18 cm will be measured and paid) 195 Supply & laying old size sub class "B" bricks laid flat in trenches over the cable with the length of brickperpendicular to the directionof cable length, adjacent/abutting each othercomplete all as specified and directed by Engineer-in-charge. 196 Supply and fixing galvanised pipe light grade (IS-1239) 40 mm bore for passing of cable fixed to poles/walls/laid under floor/ road/ hardstanding complete with and including fittings as required compete all as specified and directed Engr-in-charge.
|
