|
Tender For Special Repair To Bldg. No T-13 Jaman Singh Line (Or Md Accn) At Grrc Lansdown.; 1 Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 2 M&L for brick work with old size full bricksubclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed. 3 M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast,water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. 4 Demolition of PCC in ground floorand pavings not exc 15 cm thickness below or above ground levelincluding removal of rubbish out side MOD land complete all as specified and directed. 5 M&L Plain Cement concrete Type D-2, 1:4:8 (40mm graded aggregate), as in foundation, filling and mass concrete complete all as specified and directed. 6 M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate. 7 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 8 M&L for non skid, joint free, coloured ceramic tiles7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:6), area of each tiles Area of each tile exc 0.11 Sqm but not exc 0.18 Sqmcomplete all as specified and directed :- 9 M& L for Glazed coloured ceramic tile 300 x 450 x 6-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified. 10 All as per item 09 above but as in skirting/vertical surface including 10 mm thick plastering cement sand motor 1:4 etc complete all as specified and as directed. 11 M&L for 25 mm thick PCC (1:2:4) type B0(12.5 mm graded stone agg) as in sub floor of flooring complete all as specified and directed. 12 Dismantling of plain or corrugated steel sheeting,any gauge,thickness in roof coverings complete all as specified and directed. 13 S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 14 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 15 Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:- 16 Area not exc 1.5 sqm each 17 Area exc 1.5 sqm but not exc 4 sqm each 18 Providing and fixing windows & ventilators fabricated from Rolled Formed GI Section made of Galvanised steel colour coated(PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality. Galvanised as per IS 277 with Zinc of 90 Gsm/SqMt w. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.GI Section of 0.58mm thick inDouble rebate windows in which both glazed shutter andflymesh shutter, 74 X 60mm outer frame , Mullion 72 x 49mm, Glazed shutter 48 x 22mm, Flymesh 41 x 22mm, Beading with round ends for Glass Fixing 12 x 12mm in fixed portion and the outer frame and mullions to have rebate for glazed/gauzed shutters the sections cut to length metre joined with corner PolyVinylChloride brackets centre mullion fixed with PolyVinylChloride Mullion caps . Glass of 4mm thick plain float glass fitted with Ethylene Propylene Diamine Monomer in glazed shutterand wiremesh of Stainless steel of 36 guage to fix mesh in mesh shutter using VC Black Gypsum Drywall screws and Spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of polyvinylchloride with crca of zinc phosphate coat.Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 in each,PolyVinylChloride handle 1 in each and Powder coated Peg stay in Glass shutter.Window shall be provided with Powder coated MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat with countersunk holes at both vertical ends . Gap between the bars should not be more than 150mm .Window frames shall be fixed to brick / concrete masonry by using nylon self expension caps & 75/100 mm MS screwsafter drilling in walls. VC Black Gypsum Drywall screws should be used while fixng corner brackets,stay,hinges,mullion caps of windows all as spd and directed. 19 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable andvariation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately. 20 65mm x 125mm size 21 65mm x 100mm size 22 S & F 30 mm thick factory made modularsingle extruded WPC (Wood Polymer Composite) Wire mesh / glazed solid decorative typedoor shuttercomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 23 S & F 30mm thick factory made modularsingle extruded WPC (Wood Polymer Composite) solid decorative type flush door shuttercomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 24 M&L for preparation of old painted surface of wood and wooden based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paintcomplete all as specified and as directed. 25 Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed. 26 M&L for 10mm thick rendering on fair faces of brick work or concrete surface in cement plaster (1:6) finished the surface even and smooth complete all as specified and directed. 27 M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick CM (1:6), and IInd layer 5mm thick CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed.Note :- WPC (Liquid type) shall be measured and paid separately as supply only. 28 Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed. 29 M&L for preparation ofnewly plastered surfaces on walland apply 1mm thick of Birla/ JK wall care putty for smooth finish of wall complete all as specified and directed. 30 M&L forPreparation of old surface shall include brooming down or steelwire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots ofplastered or unplastered andapplying two coat ofOBD over and incl of one coat of alkali resistance priming painton wall surface complete all as specified and directed 31 M&L for new surfaceplastered or unplastered andapplying two coat ofOBD over and incl of one coat of alkali resistance priming painton wall surface , complete all as specified and directed 32 M&L for preparing old decorated plastered surfaces of wallby complete removal and applying two coats ofcement base paint over a coat of cement primer complete all as specified and directed. Note :-The old plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. 33 M&L for preparing newly plastered surfaces of wall and applying two coats ofcement base paint over a coat of cement primer complete all as specified and directed. Note :-The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. 34 M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed. 35 Demolition of RCC n"exc 15cm thik (blew of above grond level) including cutting of reinforcement to facilitate demolition complete all as specified and directed.Note : Reinforcement obtained from demolition will be considered credit sch as scrap iron. 36 M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 37 S& F in repair PVC (SWR) bends with access door any radius of 110 mm bore complete all as specified and as directed. 38 S&F in repair PVC (SWR) junction single, (single T) with access door equal or unequal of 110 mm borecomplete all as specified and as directed. 39 S&F in repair PVC (SWR) vent cowl of 110 mm bore complete all as specified and as directed. 40 S&F in repair PVC (SWR) pipes double socketed in any length with rubber ring joints and fixed to wall of 110 mm bore complete all as specified and as directed. 41 S&F MS butt hinge, medium weight, cold rolled and fixed of 100 mm long complete all as specified and directed. 42 S&F150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and directed. 43 S&F 300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed. 44 S&F 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed. 45 S&F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and directed. 46 S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed. 47 Disconnecting and dismantling of water storage tank and removing from the site ofCapacity exc 250 Ltr but not exc 500 Ltr of tank completeall as specified and as directed. 48 S&F rotational moulded polyethylene water storage tank, capacity 500 ltr double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, ofcapacity 500 ltr of tank completeall as specified and as directed. 49 S&F Stop valve, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed of 20 mm bore complete all as specified and directed. 50 S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. 51 M&L for cast iron floor trap with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1, of 100 mm size complete all as specified & directed. 52 S&F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx 330mmx160mm complete all as specified and directed. 53 S&F PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia complete all as specified & directed. 54 S&Fvitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed.Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc. 55 Supply only PVC flexible waste pipe 32/40 mm diawith socket fixed with sink waste couplingcomplete all as specified and as directed. 56 Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern complete all as specifiedand directed. 57 S&F chromium plated brass tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed. 58 Supply onlyPVC connection 15 mm size with PTMT nut 450 mm length complete all as specified and directed. 59 Cutting chases,pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves,lintels etc; and cutting chases for concealed water tubing and making good, cutting not exc. 10cm girth. 60 Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :- 61 15mm bore 62 20mm bore 63 S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-Note :-80mm and 100mm bore pipe will be jointed by welding as directed at site 64 15mm bore 65 20mm bore 66 S & F in repair Brass chromium plated Mixer for mixing hot & cold water,screwed down high pressure with long screwed shanks and fly nuts,screwed for iron pipes 15 mm bore dia. 67 S&F in repairs Pillar tap 15 mm dia fancy type, cast copper alloy, with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with scrwed shanks and fly nuts, screwed for iron pipe and fixed make seiko complete all as specified and directed. 68 S&F in repair 15mm Bib tap fancy type cast copper chromium plated alloy with capstan handle screwed down screwed for iron pipe or for brass ferrule and fixed. 69 S&F PVC bathroom cabinet with mirror of size 559 mm x 343 mm pasted coloured with mirror shutter and built in shelves complete all as specified and as directed. 70 S& F in repair Brass chromium plated shower rose 125mm size fancy type, with CP neck 9 inch long with swivel joints, incl fixing to steel pipe or union of 15 mm bore all as specified and as directed. 71 S&F 15 mm Stop Angle valve cast copper alloy chromium plated15mm dia, screwed down, high pressure with capstan handle, screwed both ends for iron pipes or for unions and fixed ,complete all as specified and as directed. 72 S&F in repairs for stainless steel non magnetic curtain rod of 25mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE both side of each rod complete all as specified and directed.Note: - Measurement will be taken between end point of knobs. 73 M&L for Pre- Polished granite slab machine cut of any shade as approved by GE of 20 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones complete all as "specified and as directed. 74 S&F in repair stainless steel kitchen plate rack0.80mm thick sheet of over all size 24" x 36" x 10" fixed with steel screws and steel rawal plugscomplete all as specified and directed. Note :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. 75 Demolition and breaking up drain pipes ( SGSW pipe) of 150 mm nominal bore of pipe, set in cement mortar complete all as specified and as directed. 76 M&L concrete bed to pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for 150 mm bore sewer pipe line complete all as specified and directed. 77 M&L for salt glazed stone ware (SGSW) pipe, grade A, ISI marked, laid in trenches and jointed in CM (1:1) for 150 mm bore of pipe complete all as specified and directed. 78 Dismantling of timber scantling 40 sqcm and over in section, in any position as in framed work complete all as specified and as directed. 79 M & L for 2nd class hardwood in timber scantling for wall panelling, ceiling, roof truss,post, purlins, rafters and similar work (Clean sawn Timber framed and fixed type) including necessary coating framed joints with glue complete all as specified. 80 Dismantaling of Wallandceilingboards(fibre, pulp, insulation, etc.) or insulationboards/slabs/ blankets, any thickness, including cover fillets 81 M&L for providing E-boards, ceiling, 4 mm thick with J framed work with mainTee of size 24 x 28.5 mm made out of PGI sheet .3 mm thick double at web and single at flange, flange coverd with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x .45 mm powder coated for ceiling , ceiling boards 60cm x 60cmx 4mmthick , suspended with GI wire 2mm dia and 2m average length with adjustable hanging device complete including plugging in brick/stone walls with steel rawl plug @ 600 mm C/C Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides and painted with two coats of oil bound distemper incl making good all the disturbed portion complete all as spd & directed. 82 Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. 83 M & L for 2nd class hard wood boarding 20 mm thickplaned one side and edges tounged & grooved or rebetedfixed to timber frame work with nailscomplete all asspecified and directed. . 84 E/M Portion - Dismantling and taking down old unserviceablepoint wiring of any type (light, fan, socket, power etc) complete with fitting such as switches, sockets, ceiling roses, pendants, lamp holders, light fitting etc including CI/ pressed steel terminals, switch box and making good the disturbed surface of wall/ floor etc to match with the existing surfaces of wall/ floor complete all as specified and directed.Note :- (i) If the contractor fail to make good the disturbed surface of wall/ floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute, the decision of Accepting Officer will be final and binding.(ii) Old fittings/ fixtures / accessories like switches, sockets, lamp holders, regulators etc., if found in serviceable condition shall be removed carefully for reuse in the work or taking on charge. (iii) Only old unserviceable items will be considered in credit Sch. 85 Taking down carefully TPN DB/ MCB DB complete, removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors, etc. all as specified and directed. 86 M&L for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly cutting chases & concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) including metal flush box made of GI sheet and white cover with making good the disturbs surfaces of wall/floor/ceiling complete all as specified and directed for the following.Note: Flush box and cover plate should be of same make all as approved for switches/sockets. 87 One light/fan/bell point controlled by one No modular type switch 6 Amps single pole one way 88 One 3 pin 6 Amps socket outlet on same board controlled by one, one way 6 Amps modular switch. 89 One socket outlet 5/3 pin 6 Amps controlled by one modular switch on independent board. 90 All as per item No 78 here-in-above but wiring with 2.5 sqmm single core multi stranded copper condcutor1100 V grade PVC insulated FRLSH but unsheathed single core for16 Amps power point on independent board and 2.5 sqmm FRLSH cable as earthwire. 91 S & F switch Modular single pole,one way 6 Amps , 1 module,230 volts, 50 hzcomplete all as specified and directed. 92 S & F bell push Modular single pole,one way 6 Amps , 1 module, ISI marked, 230 volts, 50 hz complete all as specified and directed. 93 Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 Hz complete all as specified and directed. 94 Supply and fixModular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. 95 Supply and fixModular Socket outlet, 16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. 96 S&F bell electric DING DONG type,AC, 230V single pole, 2module complete all as specified and as directed. 97 Supply & fixing fancy lamp holder, insulated body ISI marked with back plate for batten fitting complete all as specified & directed 98 S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as speccified and directed 99 S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps ratinghaving following capacity complete all as specifiedanddirected:- 100 DB SPN, 12 way 101 DB SPN, 8 way 102 S&F MCB , SP, AC, 240 volts of 06 to 32Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 103 S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 104 S&F MCB, TPN, AC, 415 volts of 63 Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 105 S&F surface mounted LED luminiare, 10 watt 2 feet with all accessories having aluminumextruded channel with diffuser for glare free light, high lumen output, driver PF >0.90 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose all as directed. 106 S&F surface mounted LED luminiare, 20 watt 4 feet with all accessories having aluminumextruded channel with diffuser for glare free light, high lumen output, driver PF >0.90 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose all as directed. 107 S&F LED Bulb 10 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for "B-22 type to fix on batten holder complete all as specified and directed. 108 Supply and fixLED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.90 having over voltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit protection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70,beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminaire efficiency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on wall with 1.2 mtr 32 mm GI pipe bracket & 02 Nos MS clamp made out of F1 40 x 6 mm or as directed including connecting with 1.5 sqmm , 3 core, PVC insulated copperconductor cable 1100 Volt grade from ceiling box to light complete all as specified and as directed. 109 S&F sub main wiringtwo single core6 Sqmm PVC insulated, unsheathed, stranded copper conductor cable(FRLSH) 1100Volts grade drawn in & including rigid PVC Conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sqmm PVC insualted unsheathed copper conductor cable (FRLSH) as earth wire andwire connected with main earth dolly including cutting chases and making good disturbed portion complete all as specified and directed. Note : Two runs of phase, neutral wire and one run of earth wire and PVC conduit will be measured as one RM or one length. 110 M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground levelat any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4mm GI Wirecheck nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI strip upto 7.5 mtrs long with 15 mm dia medium grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI strip more than 7.5 mtrs will be measured and paid seperately under relevant items. 111 S&F Exhaust fan Steel body AC single phase 230 Volt of size 300 mm sweep complete with blade, Frame and louvers including making hole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. 112 S&F Exhaust fan Plastic body AC single phase 230 Volt of size 250 mm sweep complete with blade, Frame and louvers including making hole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. 113 Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hzcomplete with all accessories such as safety valve, thermostate, NRV, PVC connection pipe, plug top complete all as specified and directed . 114 Taking up/down of old U/S Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of 16 Sqmm size all as specified and directed.
|
