|
Tender For Addition / Alteration To Building No P 1 Hq 2 Stc Office At Panaji Goa - 1 Dismantling Mangalore pattern roofing tiles with ceiling tiles or slate roofcoverings. 2 Dismantling timber scantlings 40 sq.cm and over in section in any position unframed work. 3 Dismantling timber scantlings 40 sq.cm and over in section in any position framed work. 4 M&L timber framed and clean sawn 2nd class hard wood in timber scantling,fixed in repairto replace old and decayed timber (including piecing, scarfing, etc.,of old and new timbersif required) and removing defective portions to store. 5 M&L Boarding40 mm 2nd class hard woodin Floors and SkirtingPlaned one side, withbutt joints and fixed with nails supplied and fixed in repair. 6 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asspecified. 7 S&F 0.63 mm thick plain or corrugated, galvanised, mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating complete all as specified and directed. 8 S&F Rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.confirming to Fe-410-W(Gde-E-250) quality-B. 9 S&F Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each to be fitted with washers and one hexagonal or square nut exc 5 cm but n exc 10 cm long of 11 to 15 mm (dia of neck of the bolt) complete all as specified and directed. 10 S&F Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each to be fitted with washers and one hexagonal or square nut exc 22.5 cmbut n exc 30 cm long of 16 to 20 mm (dia of neck of the bolt) complete all as specified and directed. 11 M&L for providing cement concrete type B1 1:2:4 (20 mm graded aggregate) as in lintels upto 1.5 m clear span , cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and kerbs stones etc including weathering, slightly rounded or chamfered angles and throating as directed complete all as specified and directed. 12 DsimantlingBattens for tiles, shingles etc, n exc 15 cm insize including tilting fillets 13 S&F mild steel sections like MS tubes etc confirming to Fe-410-W (Gde-E-250 Quality A) as in framing for cladding, glazing, secure mangalore pattern tiles in roof over sheet and like with all necessary required provisons complete all as specified and directed by Engr-in-Charge. 14 M&L Mangalore pattern Roof tiles, interlocking at side joints, laid over galvalume aluminium plain sheet including necessary provisions to fix the same over plain sheet complete all as specified and directed. 15 M & L for Ridge or hip tiles to suit Mangalore pattern of Roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 laid dry. 16 Demolition of brickwork or stone/boulder masonry, built in CM including all quoins arches pillars etc. 17 Material and labour for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius with old size bricks built in cement mortar 1:4 complete all as specified and as directed. 18 Taking down cement plaster on wall built in cement or cement mortar raking out joints, hacking for key, scrubbing out with water etc. complete. 19 M & L rendering 15 mm thickon stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing in CM 1:6without using extra cement. 20 M & L rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing in CM 1:4 without using extra cement with using water proofing compound.Note :- Water proofing compound will be measered seperatly. 21 Supply only integral waterproofing compound 22 M&L for preparation of new plastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/ltr and UV resistance as per IS 15489-2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over 3mm wall care putty on new surface completeall as specified and directed. Note :- (a) Triparty MOU shall be signed between MES, Contractor and Paint Manufacturing company for Pre,during and Post work completion site inspections. (b) An amount of 10% of this item shall be retained from every RAR and shall be released only after submission of 5 years guarantee bond by the Contractor with respect to any dampness, dullness any other defect notified/detected for painting work carried out to the building against above mentioned work. 23 M&L for complete removal of existing treatment and applying two coat of oil bound distemper over 3 mm thick puttyon plastered surfaces ofwalls including prepartion of old surfaces. 24 M&L for two coat of oil bound distemper over 3 mm thick wall care puttyon plastered surfaces ofwalls including prepartion of new surfaces. 25 M&L for preparation of old painted wooden surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge . 26 M & L preparation of new wooden surface and applying two coats of synthetic enamel paints over a coat of pink primer of any description, not otherwise described, over 10cm width or girth. 27 M&L for Anti termite treatment at points of contact of wood work by chemical emulsion in oil or kerosine based solution ) @ 0.5 ltr per hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed. 28 M & L for Preparation of New steel surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified. 29 M & L for preparation of old steel Surfaces and applying one coats of synthetic enamel paint on surfacess of any discription, over 10cm in width or girth . 30 M&L two coat Varnish with sizing, wood filler,stain on old Surfaces of any 10cm in width or girth 31 Dismantling boarding,wall panelling including fillets/ceiling/gypsum board any description, fixed in any position with nails. 32 Supply and fix false ceiling work of aluminium anodised snap grid frame work, size of grid 605 X 605mm , 6mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / GI / Aluminium frame work with screws, including hangers to purlins/truss members with 4mm dia plain GI wire all as specified and applying two coats of OBD, including preparation of new surfaces on ceilings complete all as specified. 33 Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface overmetal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) Extra over for any sunk or raised moulding Anodised aluminiumgrid frame work for false ceiling Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm longcomplete all as specifiedall as specified . 34 Taking down and removal of existing wall panelling and similar work complete all as specified and directed. 35 S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. 36 S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing . 37 Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) . 38 M&L glazed ceramic coloured designer pattern tiles 450mmx 300mmx7mm thick on vertical surface such as skirt, Dado etc set and jointed in white colour cement including 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4. 39 Demolition of cement concrete in below or above ground floor and paving n.exc 15 cm thk (unreinforced) for plinth protection & foot path. 40 M&L cement concrete type B1 1:2:4 using 20mm graded stone aggregate 25mm thick as in flooring etc. 41 M & L coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cementslurry and pointed in white or coloured cement to match incl 20mm th screed bed in CM 1:6. 42 M & L for Virified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 20mm thick screed bed in CM 1:6. 43 M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed in CM 1:6. 44 Taking down chowkat with shutter(without taking off shutter from the frame) area exc 1.5sqm but n exc 4 sqm each. 45 S & F 2nd Class H.W. plain solid straight chowkats & frames wrought, framed, rebated on the solid rounded or chamfered put together with glue, pinned at joints. 46 Supply and fix 35mm thick factory made 2nd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated. 47 S & F Second class hard wood factory made glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I 1991 section 8 clause 8.20 (b) 48 M&L for ATT of voilds in masonry using chemical emulsion one litre per hole at 300 mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floors complete all as specified and directed. 49 S&F factory made single extruded WPC (Wood polymer Composite) solid door/Window and other frames Chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58-60(suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms )fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750 Kg/Cum screw withdrawal strength of 2200 N(Face) & 11 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof waqter/moisture proof and fire retardant and fixed in position with MS Hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note : For WPC solid door/window frames minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile demensions on plus side shall be acceptable but no extra payment on this account shall be made. 50 S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade),calcium carbonate and natural fibers ( wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50 N /mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing withsteel butt hinges of size with necessary full body threaded star headed counter sunk SS screws all as per direction of Engineer-in-Charge. 51 S & F 150 mm aluminium handles,cast type anodised 52 S & F 100mm butt hinges for door and windowsmidium weight,cold rolled mild steel and fixed 53 S & FAluminium anodised barrel tower bolts150mm for door of extruded section and fixed 54 S&F 300 mm long Aluminium alloy,anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts,four on bolt plate and two on staple plate complete all as specified. 55 Taking down or up steel tubing and connection s inculding cleaning for refixing or removal to store 15mm bore . 56 Taking down or up steel tubing and connection s inculding cleaning for refixing or removal to store 20mm bore . 57 Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 58 --do-- all asabove but for 25mm bore. 59 Supply and fixing in CPVC 20mm Brass Elbow (3/4 x 1/2) 60 Supply and fixing in CPVC 20mm Brass Tee 61 Supply and fixing in CPVC 20mm Male Brass Threaded Adaptor (MTA/ MBTA) 62 Supply and fixing in CPVC 20mm Female Brass Threaded Adaptor (FTA/ FBTA) 63 S/F Gate valve of 25mm dia brass all as specified and directed 64 S/F Gate valve of 20mm dia brass all as specified and directed 65 S&F rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top ) hoisted & fixed in position all as specified in SSR PT I capacity of tank 1000 ltr including Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both ends & ball brass valves 20mm dia, high pressure, with polythene float and fly nut and Dismantling water tanks and removing to store complete. 66 S&F rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top ) hoisted & fixed in position all as specified in SSR PT I capacity of tank 500 ltr including Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both ends & ball brass valves 20mm dia, high pressure, with polythene float and fly nut and Dismantling water tanks and removing to store add fixed in repair complete. 67 S&F in repairvitreous china wash down water closet wall hung or couple closet type1st quality wash down water closet EWC White/ivory/Off white (Closed pattern incl all necessary accessories like rag bolt/gel gasket etc with vitreous china or required type valveless, syphonic action type flushing cistern of 10 ltr capacity low level white with inlet, ball valve, float and handles with all necessary fittings and fixtures 68 S&F in repair Vitreous China Table Top Basin Size 550x400 mm oval type excluding taps, waste chain and plug and porcelain stopper including necessary brackets complete all as specified and directed. 69 S&F 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building baord or comercial plywood and fixed to wooden plugs with chromium plated brass screws and cup waste washer. 70 S & F in repair Tubular towel rail 20mm dia(d) type 60cm long between flanges Brass chromium plated complete all as specified and directed. 71 S&F Pillar tap 15 mm bore fancy type chromium plated with capstan head, screwed down high pressure with or with out lettered Hot and Cold with long screwed shanks and fly nuts fixed in repair complete all as specified and directed. 72 S&F in repair Brass chromium plated Mixer for WHB /wall with Round Spout with popup waste systemsuitable for 15mm borepipe complete all as specified and directed. 73 Dismantling of old cast iron pipes including necessary bends and other fittingsjointed in cement mortar and taking out if required complete all as specified and directed. 74 S&F in repair Angular stop Cock 15mm borefancy type chromium platedscrewed down, high pressure with crutch or butterfly handle screwed both endswith long shank and cup concealed type complete all as specified and directed. 75 S&F Stop valves 15 mm fancy type chromium plated screwed down, high pressure with crutch or butterfly handle screwed both ends fixed in repair complete all as specified and directed. 76 S&F Bib taps 15 mm bore dia fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified and directed. 77 S&F Soap Dish Holder, in repairs, all as spd and directed by Engr-in-Charge. 78 S&F Toilet Paper holder with Flap Recessed Type (Stainless steel), in repairs, all as spd and directed by Engr-in-Charge. 79 S&F in repairSheet glass shelf assemblyconsisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long 80 S&F in repairsHealth faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m flexible tube and ABS wall hook including making connections and fixed in positions complete all as specified and directed. 81 Stop cock fancy type chromium plated with long shank and cup(Concealed type) screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for union and fixed 15mm bore fixed in repair. 82 S&F PVC connection 15mm bore size with PTMT nuts of length 45cm. 83 S&F Viterous china wash down water closet pan(pedestal pattern) white (excluding fixing bolts, flushing cistern and floor pipe) fixing in repairs EWC. 84 S & FPVC valveless, syphonic action type flush tank in repair, white, 10 litre capacity with inlet ball valve, float & handle incl brackets complete high level, flush pipes of PVC 32 mm dia, rubber cones, PVC connection 15 mm size with PTMT nut of length 600 mm etc complete all as directed 85 S&F Plastic water closed seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium plated or aliminished hinging device fixed in repair. 86 S & F Vitreous china urinal,half stall type flat back of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe add fixed in repair. . 87 S & F PVC (SWR) floor trap with grating 75 mm dia, plain with grating including jointing with solvent cement 88 M&L for 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors/walls as soil pipe all as spd. 89 M&L for 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors/walls as soil pipe all as spd. 90 S&F for 110mmPVC (SWR) junction single (single T) equle or unequle with access door all as spd. 91 S&F 110X75mm PVC(SWR) reducer 92 S&F 110mm PVC(SWR) bends 93 S&F 110/110 PVC(SWR) P trap all as specified and directed. 94 PVC (SWR) 75 mm dia bends any radius 95 S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32 mm Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixedall 20 mm CP Bib taps, cast copper alloy withcrutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair all as specified and directed. 96 Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors windows ventilators and partitions (fixed portions) with extruded built up standard tubular sections/appropriate Z sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS 1285 fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions i e at top bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing/panelling C P brass/stainless steel screws all complete as per architectural drwings and the directions of engineer-in-charge. 97 S & F Powder coated aluminium window and ventilator shutters fixed, openable or sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified . 98 S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples as repair. 99 S & F 4 mm thick plain sheet glass ordinary quality fix with bead in squaresn. exc. 0.5 SM in each pane. 100 M&L Block boards, grade 1quality, exterior grade, decorative type with decorative face veneer on one face, 12 mm thick, exterior grade, prelaminated both side with decorative choice laminations, fixed with screws to timber frame work. 101 S&F rolled mild steel work in stairs (Framed) including stringers,treades, landings, balusters, hand rails etc including cleats, brackets etc confirming to Fe 410-W (Gde E-250) quality A 102 Excavation in trenches n exc.1.5 M wide & n exc.1.5M in depth for foundation etc.and getting out in soft disintegrated rock. 103 M & L for PCC 1:4:8 type D2 using 40mm graded aggregate as in foundation. 104 M & L For RCC 1:2:4 Type B1, using 20mm graded aggregateSlabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and inshelves and the like 105 S & F TMT bars 10 mm dia and over, cut to length, bend to shape incl cranking, hooping etc. and binding with ms wire (annealed) not less than 0.9 mm dia. 106 Ditto, but 6mm to 8mm dia. 107 S & F Formwork to soffits of suspended slabs such as roof slabs, floor slabs etc. not exceeding 200mm thick. 108 S & F 4 mm thick PVC tiles/ sheets,laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors. 109 Providing cupboard with shutter in required sizes at site made out of 18 mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & provision of shutters made out of 18 mm thick one side decorative laminated PVC sheet all required brackets 5.5 screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specifications approved by Engineer-in-Charge. 110 Returning,filling in including spreading,levelling,watering and well ramming in layers not exc 25 cm in soft/disintegrated rocks complete all as specified and directed. 111 Removing excavated material (soils)n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed. 112 Supply and fixing factory made uPVC wooden texture colour Casement door/windows with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazingbead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVCmulti-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDMgasket, zinc alloy (white powder coated) 3D hingesand one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one sidekey, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealentover backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extrudedprofiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed. 113 Taking down carefully copper/aluminium point wiring of light, fan, socket 5/15A or power point complete including fittings such as switches, bell push,electric bell,ceiling rose, pendant, regulator, socket, lamp holders, brackets, lamp fittings,etc including switch boards and making good disturbed surfaces of wall/ceiling etc so as to match with the existing wall/ceiling/floors etc completely all as directed by Engr-in-Charge. 114 Taking down carefully sub main wiring including aluminium conductor of any size,earth continuity conductorand making good disturbed surface all as directed. 115 Dismantling oldMain Board/ wall mounted LT panel with MCBs, DBs of any size and capacity alongwith teakwood boards 116 M & L for Submain wiring complete with and including2 runs of4 sqmm single core FRLSH PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade andmultistranded copper conductor cable of 4 sqmm drawn through and including heavy grade PVCconduit of 20 mmof dia or higher size as required at site totally concealed in walls/floors/ceiling or on surfaces of trusses by means of saddles & clips etc includin all acessories / fitting / junction box / inspection covers etc of heavy grade, ISI marked with one run of 4.0 Sqmm PVC insulated FRLS, unshethed multistranded copper conductor cables as a continuous earth wire complete all as specified.Note :2 runs of 4 sqmm single core copper cable and one run of 4.0 Sqmm of Earth conductor cable with conduit will be measured and paid as one . 117 M & L for Submain wiring complete with and including2 runs of6 sqmm single core FRLSH PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade andmultistranded copper conductor cable of 6 sqmm drawn through and including heavy grade PVCconduit of 20 mmof dia or higher size as required at site totally concealed in walls/floors/ceiling or on surfaces of trusses by means of saddles & clips etc includin all acessories / fitting / junction box / inspection covers etc of heavy grade, ISI marked with one run of 6.0 Sqmm PVC insulated FRLS, unshethed multistranded copper conductor cables as a continuous earth wire complete all as specified.Note :2 runs of 6 sqmm single core copper cable and one run of 4.0 Sqmm of Earth conductor cable with conduit will be measured and paid as one . 118 Suppying, laying jointing and testing of LT cable XLPE insulated, screened, PVC sheathed aluminium conductor multistranded heavy duty 1100 volts grade electric cable of cross section area 25 Sqmm, 4 core making connection with suitable size of eyelet on both side laid in trenches/crossings/panels/walls etc.complete all as specified and directed Engr-in-Charge.Note : Excavation & earth work shall be measured and paid separately. 119 M & L for point wiring with 1.5 sqmm (nominal cross sectional area) single core pvc insulated ,unsheathed FRLSH copper cable ,1100 Volt grade with multi stranded copper conductor drawn through and including non-metallic ,rigid non metallic PVC conduit (medium grade) concealed in walls /ceiling with and including 1.5 sqmm single core PVC insulated multistranded ,unsheathed FRLSH copper conductor cable as continous earth continuity conductor (green in colour) with cast Iron/ Pressed Steel modulur terminal boxes any size/module,concealed on walls and fixed by means of brass screw including modular white cover plates and cover frames any size /module and blanck plates, for mounting or housing switches ,socket outlets, fan regulators etc incl all other fixing accesories for one light/fan/exhaust fan/call bell point controlled by one 5/6 Amps switch complete including making good of wall surface by cementing/plastering , applying wall putty incl two coat of distempering to match with the existing colour complete all as specified and directed. (a) One light point controlled by one way switch. 120 (b) One fan point controlled by one way switch and one regulator. 121 ( c) One Exhaust fan point controlled by one way switch. 122 (d) One bell point controlled by one bell push. 123 (e) One 3 pin switch socket outlet 5A on independent board. 124 (f) One 3 pin socket outlet 5A on same board with other switch 125 All as per item No. 7 above but with cable size 2.5 sqmm for switch socket outlet point 15A on independent board including 2.5 sqmm PVC insulated copper earth continuity conductor to common earth and carrying out IR test. 126 S & F Rigid non-Metallic Conduit 25 mm dia exclusive of boxes (junction/terminal) but inclusiveof all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including Fixing of LAN cable inside the Conduit 127 S & F Non Metallic Junction/Terminal Boxes(1 to 4 way) of 25 mm size 128 S & F RJ 15/RJ 45 LAN Jack with shutter ISI Marked Complete all as specified and as directed. 129 S & F for Modular type telephone socket outlet Complete all as specified and as directed 130 S & F Modular Switch 1 Way 6 Amps,1 Module ,Complete all as specified and directed 131 S & F Modular Switch 1 Way 16 Amps,1 Module ,Complete all as specified and directed 132 S & F Modular Bell Push Switch 6 Amps,1 Module ,Complete all as specified and directed 133 S & F bell electric AC 230 V SP white finish complete all as specified and directed. 134 Supply & fixing Modular socket outlet 6A- 2/3 pin Combined 2 module ISI Marked complete all as specified and directed 135 S & F Modular stepped type Fan Regulator 120W 2 Module suitable for 230V 50 Hz AC Supply complete all as specified and directed. 136 Supply & fixing Modular socket outlet 6/16A - 2/3 pin Combined 2 module ISI Marked complete all as specified and directed 137 S & F surface ceiling rose made of bakelite of size 65mmx50mm with 3 terminals and PVC block. Ceiling rose will be fixed on PVC block.white finish complete all as specified and directed. 138 S&F Suspension (pendant) luminaries40 watt with efficeient Diffuser ensuring perfectly uniform illumination, ensured and optimised and unparalled light distribution .Inter connectable luminaires for aesthetically appealing down light application including necessary fixing the hanging wires from RCC ceiling with suitable fastners,mounting,end cap ,making good disturbed surfaces with necessary mason and painting work to match with existing surfaces all as specified and directedcomplete all as specified and directed. Make: BPCS 40 W LED 4F WH or its equivalent in Wipro,Philips 139 Supply and fix lamp holder insulated body suitable for batten fitting white finish complete all as specified and directed. 140 Supply and fixing for LED luminaire 600 mm x 600 mm, square LED Panel 36 Watt ,lumen output >= 110 lumen/watt , 220 V AC Ceilingmounted type with high effeciency PMMA diffuser soft glare free light complete with driver holder, LED lamp suitable for roof/false ceiling ,including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Eng-in- Charge 141 Supply and fixing High-quality design LED Tube lightfittings in extruded aluminium housing with high quality PC diffuser 1x20 wattwithenhances safety and relible ,robust housing structurewithefficiency of 120 lm/W ,decorative end caps complete with all accessories internallypre-wired and including connecting up with twin core twisted flexible copper conductor cable includingtaking down old light fittings complete all as specified and directed. 142 S&F LED Batten Tube Light light fittings10 Watt and fixed with wall surface with anodized extruded aluminium housing, high transmissitivity diffuser and high lumin output and connecting with 3 core flexible copper cable PVC insulatedcomplete all as specified and directed. 143 Supply & fixing Exhaust fan 300mm sweep, steel body, single phase, 230 Volt heavy duty, with louvers, shutter including three core flexible cable of required length of size 23/0.0076 from ceiling rose/ connector to fan terminal opening the wall as required, fixing the fan with suitable size of nut, bolt washer, providing of opening on wall where required and making good the disturbed surfaces complete all as specified and directed. 144 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m 145 M & L for fixing DB-SPN-12 way 230 V double door flush typemade of sheet metal with 200A rated copper/ Aluminiumbus bar including. 146 Supply and fixing amp rating 240V, 10KA C curve miniature circuit breaker (MCB) SPN 40 to 63 AMP current carrying capacity in the MCBDB complete with connection testing and commissioning.Make :Same as Item no. 26 147 Supply and fixing 240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity MCB SP 40 AMP, in the MCB DB Complete with connection testing and commissioning.Make :Same as Item no. 26 148 Supply and fixing amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. (i) SP 6 To 32 AMP 149 M & L for fixing DB-VTPN-4 way 415 V double door flush typemade of sheet metal with 200A rated copper/ Aluminiumbus bar including suitable for fixing MCCB 100 A Note : MCCB will be measured seperately. 150 Design, Supply, Install, test and commissioning of wall mounted, dust and vermin proof LT cubical panel, indoor type, as per lS-8623 fabricated with 2 mm thick CRCA Sheet, powder coated after due preparation of surfaces be painted with epoxy powder paint by means of electro static gun after rigorous pre treatment comprising of cold phosphating process on all internal and externalsurfaces after due preparation of surfaces, including bottom gland plate consisting of suf?cient Nos of circular cable entry holes at bottom only with suitable PVC/rubber bushes to prevent ingress of water/vermin etc, inside the enclosure the required No of holes to be ?xed with chromium plated brass cable glands for incoming and out going cables with necessary internal wiring with stranded copper conductor PVC insulated cables of adequate size including connection. The panel shall be provided with separate compartment for each switch gear etc. front openable suitable for 1100 volts grade,3 Phase,415 Volts. 50 cycles. AC supply and to withstand short circuit fault level of not less than 10KA and degree of protection shall be IP48. The panel shall be comprising of the following :- (a) MCCB FP-415V, 50 Hz. 25 KA, 250 Amps,Ics=100% Icu thermal adjustable - 01 No (incoming)(b) On Load Change over Switch 160 A - 01 No (c) MCCB FP-415V. Hz. 16 KA. 100 Amps - 2 Nos (Outgoing)(d) MCB DP-230V, 50Hz. 10 KA, 40 Amps - 7 Nos (Outgoing)(e) MCB DP-230V, 50Hz. 10 KA, 32 Amps - 5 Nos (Outgoing)(f) aluminium Bus bar 600 Amps -03 Nos(g) Volt Meter Digital type with built in selector switch 0-500 Volts-01 No.(h) Ammeter Digital type with built in selector switch 0-200 Amps along with suitable size of CT.‘s-01 No (j) Digital time switch with astronomical function `Note : The panel shall be of CPRI approved Make and Test report shall be submitted by the contractor. 151 MCCB 4 Pole, 415 V, fixed type, 100 Amps ,Ics=100% Icu with breaking capacity 25 KA 152 Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 A all as specified and directed. 153 Disconnecting and taking down ceiling fan of any sweep any make from any position at site, transporting to MES store Yardand rehanging/ re-fixing/ placing fan at same location at site includingproviding nuts, bolts, locking bolts, blades screws, split pin, rubber real, PVC connector, washers, of suitable size etc as required and re-painting one coat of supper enameled white paint with spray painting technique complete all as directed. 154 S & Fcord flexible 23/0.0076 including dismantling old unserviceable one as directed by engr-in-charge.. 155 Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion 156 Supply and fixing LED bldg security light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. 157 Supply and fixing Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, 70W suitable for highlighting architectural facade and general purpose lighting 158 Supply and fixing LED Bamboo light 8 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP65 protection, completeall as specified and directed. 159 M & L for PCC work(1:3:6) type C-2 using 40 mm graded mechanically crushed stone aggregate as in foundation of stay / coping of poles including necessary form work and fare finish to exposed surfaces without using extra cement etc. complete all as specified. 160 Supply and laying or fixing or passing through pipe, 2 core 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor armoured PVC sheathed 6 sq. mm nominal cross section. 161 Supply & fixing of SMC terminal/junction box of size 140 x 140 x 95 ofpolycarbonate thermoplastic housing, weather, water proof fire retardant including 02 Nos terminalon boundry walland provision for fixing one MCB SP as specified and directed. 162 Material and labour for bracket made out of GI pipe 40 mm dia medium grade, 1.2 meter long bent to shape fixed with MS flat irom clamps made out of 40mm x 6 mm thick, nuts bolts complete all as specified and directed. 163 Excavation in trenches in hard/dense soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and gettingout complete all as specifiedand directed by Engineer-in-Charge. 164 Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer compete all as specified and directed by Engineer-in-Charge. 165 Removal of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point completeall as specified and directed by Engr-in-charge. 166 Supply and Laying DWC HDPE pipe of outer dia of 40mm and inner dia 32mm polyethylene (PE) with smooth internal and profiled external surface for non-pressure for underground cable including bends complete all as specified and directed. 167 Supply and fixing GI pipe 80mm bore, light grade laid complete for road/ footpath crossing complete all as specified and directed. Note: PCC will be measured under respective item under sch A.
|
