Quotation Are Invited For Replacement Of Batteries (Mitsubishi Emergency Landing Device) in United Arab Emirates

Work Detail

Quotation are invited for Replacement of Batteries (Mitsubishi Emergency Landing Device) for Head Office Elevators. SPECIFICATION FOR EMERGENCY LANDING DEVICE BATTERIES MITSUBISHIELEVATORS AT DEWA HEAD OFFICE INTRODUCTION THE FOLLOWING DOCUMENTOUT LINES THE SPECIFICATIONS FOR THE BATTERIES USED IN THE EMERGENCYLANDING DEVICE (ELD) FOR MITSUBISHI ELEVATORS AT THE DEWA HEAD OFFIC E.THIS SPECIFICATION INCLUDES DETAILS FOR TWO TYPES OF BATTERIES: 12V 7AHAND 6V 4.5AH, WITH THE QUANTITIES REQUIRED LISTED BELOW. SC OPE OF WORKTHE BIDDER TO VISIT THE SITE AND QUOTE LUMP SUM PRICE FOR THEREPLACEMENT OF THE DEFECTIVE ELD BATTERIES FOR THE 7NO OF MI TSUBISHIELEVATORS IN DEWA HEAD OFFICE AS PER THE BELOW BUT NOT LIMITED TO THESPECIFICATION. BATTERY SPECIFICATIONS 12V 7AH BATTERIES QUANTITY: 24UNITS#NOMINAL VOLTAGE: 12V#CAPACITY: 7AH#DIMENSIONS (L X W X H): APPROXIMATELY 151 X 65 X 94 MM (MAY VARYSLIGHTLY BASED ONMANUFACTURER)#WEIGHT: APPROXIMATELY 2.1 KG PER BATTERY#DESIGN LIFE: 3-5 YEARS (STANDBY USE)#OPERATING TEMPERATURE RANGE: -20°C TO 50°C#RECHARGEABLE: YES#MAINTENANCE: SEALED, MAINTENANCE-FREE#COMPLIANCE: MUST COMPLY WITH INDUSTRY STANDARDS AND CERTIFICATIONS(E.G ., ISO 9001, UL)6V 4.5AH BATTERIESQUANTITY: 20 UNITS#NOMINAL VOLTAGE: 6V#CAPACITY: 4.5AH#DIMENSIONS (L X W X H): APPROXIMATELY 70 X 47 X 101 MM (MAY VARYSLIGHTLY BASED ONMANUFACTURER)#WEIGHT: APPROXIMATELY 0.7 KG PER BATTERY#TERMINAL TYPE: F1 OR F2 (TO BE SPECIFIE D BY USER)#MAX DISCHARGE CURRENT: TYPICALLY AROUND 67.5A (5 SECONDS)#DESIGN LIFE: 3-5 YEARS (STANDBY USE)#OPERATING TEMPERATURE RANG E: -20°C TO 50°C#RECHARGEABLE: YES#MAINTENANCE: SEALED, MAINTENANCE-FREE#COMPLIANCE: MUST COMPLY WITH INDUSTRY STANDARDS AND CERTIFI CATIONS(E.G., ISO 9001, UL)INSTALLATION AND MAINTENANCEIT IS ESSENTIAL TO ENSURE PROPER INSTALLATION AND MAINTENANCE OF THEBATTERIES TO GUARANTEE OPTIMAL PERFORMANCE AND LONGEVITY. THE FOLLOWINGGUIDELINES SHOULD BE OBSERVED:#ENSURE BATTERIES ARE INSTALLED IN A WEL L-VENTILATED AREA.#REGULARLY CHECK THE BATTERY TERMINALS FOR SIGNS OF CORROSION AND CLEANAS NECESSARY.#AVOID EXPOSING BATTERIES TO E XTREME TEMPERATURES OR MOISTURE.#FOLLOW THE MANUFACTURER#S INSTRUCTIONS FOR CHARGING AND DISCHARGINGCYCLES.GENERAL CONDITIONS#THE CO NTRACTOR AT DEWA WORK PREMISES SHALL FOLLOW DEWA SAFETY&ENVIRONMENT POLICY, RULES AND REGULATIONS DURING THE CONTRACT PERIOD.#THE CO NTRACTOR SHALL CARRY OUT RISK ASSESSMENT FOR ALL HIS WORKS. THISRISKASSESSMENT SHALL BE FROM SAFETY AS WELL AS OCCUPATIONALHEALTHCON SIDERATIONS. (DEWA FORMAT TO BE USED).#TOOLBOX TALKS SHOULD BE GIVEN TO THE WORKMEN BY THEIR SUPERVISOR, COPYOF WHICHSHALL BE GIVEN TO DEWA.#NO WELDING, FLAME HEATING OR CUTTING, GRINDING, PNEUMATIC CHIPPING,ETC. SHALL BECARRIED OUT WITHOUT SPECIFIC CLEARANCE FROM DEWA THROUGH"HOT WORK PERMITS".THE HOT WORK PERMIT IF REQUIRED SHALL BE OBTAINED ONDAILY BASIS.#THE CONTRACTOR SHALL AT NO TIME KEE P INFLAMMABLE SUBSTANCES INTHEPLANT/WORK AREAS.#ALL HAZARDOUS WASTES SHALL BE MOVED UNDER DIRECTION FROM AND WITHWRITTEN APPROVAL TO DEWA SPECIAL STORAGE AREA.#THE CONTRACTOR#S WORK WILL FALL WITHIN THE PURVIEW OF SAFETY SURVEYSCONDUCTEDREGULARLY BY THE DEWA SAFET Y SECTION.ALL THE WORKMEN SHOULD WEAR NECESSARY PPES LIKE UNIFORM, SAFETY SHOESAND HELMET WHILE AT WORK.#ALL CRANES, VEHICLES, SPECI AL TOOLS OF CONTRACTOR SHALL BE INSPECTEDANDTESTED BY CAPABLE AUTHORITIES AND CONTRACTOR SHALL PROVIDE DEWA WITHCOPYOF CERTIFICATES OF THEIR FITNESS BEFORE THEIR USE AT SITE#ALL EQUIPMENT LIKE RIGGING TOOLS, GRINDING MACHINES, DRILLING MACHINES,HAND TOOLS,PRECISIO N TOOLS WITH ALL VALID TEST CERTIFICATES FROM 3RDPARTY LICENSED CERTIFYINGAGENCIES SHALL BE PRODUCED BY THE CONTRACTOR.#ERECTION & U SE OF SCAFFOLDING, USE OF LIFTING TROLLEYS SHALL BECERTIFIED BY DEWAAUTHORIZED PERSONNEL AND SHALL BE SUPERVISED BYCONTRACT SUPERVIS OR BEFOREEXECUTING THE JOB ON SITE.#E PASS SHOULD BE APPLIED THROUGH DEWAPORTALHTTPS://WWW.DEWA.GOV.AE/EN/SUP PLIER/SERVICES/EPASS-LA NDING#NO STAFF OR VEHICLES OF THE CONTRACTOR WILL BE PERMITTED TO STAY INDEWAPREMISES AFTER CLOSE OF WORK OF THE DAY.PAYMENT100 % ON SATISFACTORY COMPLITION OF WORKS.SITE VISIT:THE TENDER MUST VISIT AND EXAMINE THE SITES AND THE SURROUNDINGS. OFFERSSUBMITTED WITHO UT A SITE VISIT/ASSESSMENT OF THE SCOPE OF WORK WILL NOTBE CONSIDERED.CONTACT US FOR THE SITE VISIT DURING THE DUTY HOURS FROM 7:30 AM TO 2:30AM MONDAY TO THURSDAY.# MR. MUHAMMAD TAHIR 0566357045# MR. THOMAS KUTTY 0557988468 Qty: 24 REPLACMENT OF MELD BATTERY 6V 4.5AH Qty: 20 STANDARD TERMS & CONDITIONS 1) Prices should be DDP delivery duty paid at DEWA stores. 2) Quotation to be submitted only in local currency U.A.E Dirhams 3) DEWA Standard payment terms is 30 days credit from the date of acceptance of material 4) No DEWA staff or his or her relatives up to third degree should have ownership or partnership in your company, and your participation in DEWA tenders / RFQs should not constitute a Conflict or perceived Conflict of Interest. Supplier Registration: https://srm.dewa.gov.ae/irj/portal/anonymous/regis Tender Link : https://srm.dewa.gov.ae/sap/opu/odata/sap/ZSRM_RFX_REG_BID_SRV/AttachmentSet(2412402007)/$value

Contact Information