|
Providing And Supplying Furniture For Iti Nizar At Nizar, Dist.Tapi-1 Providing and supplying Visitor or Guest chair the seat & back made of 12mm thick hot pressed plywood upholstered with changeable fabric upholstery covers (as per requirement) and molded PU foam, together with molded seat & back covers. The back foam should be designed with contoured lumber support extra comfort. The size of chair 45cm x 38cm (Back side) and 45cm x 43cm (seat size). The PU foam should be molded with density =45 ± 2 kg/m3. The armrests with Leg made with Powder coated MS structure as per architect selection. The Seat and back fixed with MS structure with required necessary hardware. complete as per sample approved and as directed by the Architect and approved by the Engineer in Charge 2 Providing and supplying Table made with 19mm Thk. Plywood(M1) structure as per architect drawing finished with mm Thk. decorative laminate(M24) on outside portion &0.8 mm Thk. liner Laminate inside as specified & approved by architect with fixed with necessary fixtures and fastening (Hardware) (M14) as per architect drawing. Provide Plastic Computer Desk Table Grommet Cable Wire Outlet Hole Cover 60mm, Key-board trey, S.S legs, Drawers with telescopic roller channels (M15), Handle (M19) and locking (M16) arrangements with all necessary fixtures and fastening (M14).Provide Shutters as per drawing fixed with handle (M19), hinges (M18), magnet (M14), complete with bidding patties and all required hardware (M14).Provide footrest as per drawing. All exposed edges shall be covered with required Teak wood beading Patti (M4) finished with approved melamine polishing (M29) work. Complete as per architect's drawing and as per instruction of architect & engineer in charge. (Refer drawing) 3 Providing and supplying Centre Table/Corner Table/Tipoi with Glass top made with 19mm Thk. Plywood (M1) finished with 1.0 mm Thk. decorative laminate sheet (M24) specified and approved by architect & fixed with necessary fixtures and fastening (Hardware)(M14) inclusive of approved melamine polishing(M29)work. Top part of center Table covered with 8 mm Thk. toughened Glass (M27) with Polished Edges. Complete as per architect's drawing and as per instruction of architect & engineer in charge. (Refer drawing) 4 Providing Visitor’s group seating of three people made from perforated S.S. CRC sheet (C-201), steel plate with 1.5mm thick. Bottom: made from 20mm x 40mm S. S.CRC tubes as per sample finished with stainless steel chrome plated as specified in specification sheet and as approved by Engineer-in-charge. 5 Providing and supplying Student Bench Specification (2 Seated) TYPE: Steel structure of MS angle & made with using 19mm Thk Plywood (M1). Structure finished with 1.0 mm Thk decorative laminate (M24) sheet fixed with necessary fixtures and fastening (Hardware) (M14) top, Seat & Back rest with ms structure. STRUCTURE: Made of MS square box section 25 x 25 x 2.6 mm welded and one coat of metal primer of reputed made shall be applied after proper surface finishing and applying putty on the surface and over it one under coat and one final coat of superior quality synthetic enamel paint of standard make and ISI market confirming to IS- 2392 shall be applied. The whole consignment of supply order shall be painted in the same shade only.Complete as per architect’s drawings and as [er. instruction of architects and engineer in charge. (color shade selection by architect) 6 Providing & Supplying Aluminium Ceramic Steel Whiteboard, For School. Color: white, Usage/Application: School. Size/Dimension: customize. Brand: e3 ceramic. Frame Material: Aluminium. Input Method: Marker etc. complete as per sample approved and as directed by the Architect and approved by the Engineer in Charge 7 Providing, supplying, and fixing a complete projection system, including a projector and screen. The projector shall be of Epson or an equivalent standard brand with specifications such as Full HD 1080p resolution, 3000 lumens brightness, LCD chipset, Android OS, built-in 5W speaker, 1920x1080 pixel resolution, 16:9 aspect ratio, a maximum projection distance of 25 feet, a lamp life of 6000 hours, and 1 HDMI port. The projector shall include a 2-year warranty for manufacturing defects. Additionally, providing and fixing a 7x5 feet self-lock projector screen with a square shape, wall mount configuration, 90-degree viewing angle, and a 1-year warranty. The installation shall be carried out as per the specifications and directions of the Engineer-in-Charge, with prior confirmation before supply. 8 Providing and Arranging NEWSPAPER STANDS TOP : Made of 18mm THK. ISI Marked Pre Laminated MDF Board IS-14587- 1998. in approved shade with half round lipping with thinner polish or touch wood polish, shall be fitted angle frame of 32 x 32 x 3/2.5 mm contains one extra lengthwise support of same angle. STRUCTURE : Made of M.S. angel 32 x 32 x 3/2.5 duly welded. Confirming to IS. PAINTS : Two coats of air drying synthetic enamel paints of ISI mark Confirming to IS-2392 made over two coat of metal primer. FINISHED SIZE : Finished size of Structure and top shall be as shown in figure. Including all materials and labours etc. complete as per drawing and instruction of Engineerin charge. 9 Providing and Arranging of 100 Litre capacity LLDPE solid waste bin having size at top 500mm & bottom 350mm square, height 900mm having standard weight as per the manufacturer's specification of 1 unit including all necessary fixture, fastners, fittings, labour, material, machinary etc. complete as seletced and diretced by Engineer-in-charge. 10 Providing and Arranging S.S. Nickle chrome plated Dustbin having 254mm dia. & 356mm height with perforated S.S. sheet having thickness 18G including all necessary fixture, fastners, fittings, labours, materials, machinary etc. complete as seletced and diretced by Engineer-in-charge. 11 Providing & Supplying Podium size 0.65 x0.45x 1.20 m(hight) made of 19 mm thick allproof plywood of BWR confirming to IS 710 of green or century make, designs & grooves as directed by architectural drawings including Two drawer size of 0.30 x 0.45 x0.28 mt with teack wood design Lamination of 1.0 mm thick in single or double shade of green, broom or equivalent make of plain or texture finish as directed on all visible face including on teck wood batten patti and telescopic sliding channel, Enox or equivalent make S.S. sliding rail, S.S. Decorative handle, with necessary fixtures & fasteners,cable passing arrangement of standard make as per detail drawing and image also including all labours as approved by engineer-in-charge etc. complete. 12 Supplying and fixing Notice board made from teak wood size of board is 1.20 x 0.90 x 0.05 with 3mm plain glass door including thrmocole coted inner side with wellvet cloth upper side also including backside 9mm thick allproof ply and polishing including necessary handles locking arrgnte ment as directed by engineer-in-charge. 13 Providing and supplying workshop and lab stage made with using 19mmThk plywood (M1) and good quality wood (M5) frame structure with required necessary legs support fixed with necessary fixtures and fastening ( hardware) (M14) All exposed edges shall be covered with required teak wood beading Patti (M4). The whole workshop and lab stage finished with approved superior quality synthetic enamel paint of standard make and ISI market confirming to IS-2392 shall be applied. Complete as per architect’s drawings and as per instruction of architect and engineer in charge.(Refer drawings) Size:- 560 x 360 x 30 cm 14 Providing and Arranging three seater Fabric sofa made from Indian teak wood with Seat made from 100mm thick 40 density foam with 50mm thick supersoft HD covered for softness. seat to be kept on high density nylon elastic belt inside Framing size 50mm x 37mm support armrest, legs and outer frame having size 80mm x 37mm with inner brace between armrest and seat frame having size 25mm x 50mm as showing the photographs. Back 80mm thick 40 density foam with 12mm thick supersoft HD covered for softness. Seat and back covered with high quality fabric approved shade Including all materials, hardwares and labours etc. complete as per drawing / photographs & detail and as directed by Engineer-in-charge. 15 Providing and Arranging Office Under Table footrest Size - 44(L) 29(w) x 12(h) including all materials and labour etc. complete as per drawing / Photographs and instruction of engineer-in-charge. 16 Providing and supplying Roller Blinds assemblies are to be supplied & installed in all windows with great precision. It should be water resistant and fitted on aluminum head rails duly powder coated and fitted with stainless steel drive rods. Manual operated and should have ISI mark. Complete or as directed as per architect & engineer in charge. (M34) 17 Providing, supplying, installing, and fixing a USB-CONFERENCE- 12 package, suitable for a 12-person wireless microphone/USB interface setup. This package includes three 1/2-rack receivers and twelve digital wireless conference microphones operating in the 900 MHz frequency band to avoid Wi-Fi interference in the 2.4 GHz range. Each receiver is equipped with four balanced XLR outputs and one 1/4" mixed output, along with audio I/O options of 4 x 1/4" TS mic input and 1 x 1/4" TS line output. The work includes all wiring, fixing, and electrical connection charges and shall be executed as per the specifications and instructions of the Engineer-in-Charge, with confirmation before supply.
|
