|
Supply Testing Installation Commissioning And Demonstration Of Hand Tools Instruments Equipment And Machineries Of Electrician And Turner Trade At Iti Jalpaiguri , Supply Of Short Fall Of Electrician Trade Course , Relay- Reverse Current, 16A, 440V , Relay- Over Current, 16A, 440V , Relay-Under Voltage, 360V-440V , Pin Type Insulators Including Hardware Fitting , Shackle Type Insulators Including Hardware Fitting , Egg Type Insulators Including Hardware Fitting , Suspension Type Insulators Including Hardware Fitting , Laboratory Type Induction Coil, 1000 W , Knife Switch Dpdt Fitted With Fuse Terminals, 16 Amp , Knife Switch Tpdt Fitted With Fuse Terminals, 16 Amp/ 440 V , Earth Plate, 60Cm X 60Cm X 3.15Mm Copper Plate , Earth Electrode,Primaryelectrode2100x28x3.25Mm Secondary Cu Strip 20X5mm , Mccb, 100Amps, Triple Pole , Twisted Pair Cable, 1 Mtr , Non-Metallic Sheathed Cable , 1 Mtr , Underground Feeder Cable , 1 Mtr , Ribbon Cable , 1 Mtr , Metallic Sheathed Cable, 1 Mtr , Multi-Conductor Cable, 1 Mtr , Coaxial Cable , 1 Mtr , Direct-Buried Cable, 1 Mtr , Rheostat(Sliding Type), 0-25Ohm,2Amp , Rheostat(Sliding Type), 0- 300Ohm, 2 Amp , Rheostat(Sliding Type), 0-1Ohm, 10Amp , Rheostat(Sliding Type), 0-10Ohm,5Amp , Bus Bar With Brackets, 1 Mtr Each , Rcc Pole With Accessories (Ms Angle Iron, ‘C’ Clamp, Stay Insulator Etc.) And Materials, 6 Mtrs , Digital Multi Meter, Dc 200Mv -1000V,0 – 10A & Ac 200Mv- 750V , 0-10A, Resistance 0-20 M? And 3 1/2 Digit , Digital Wattmeter, 230 V, 1 Kw, 50 Hz , Magnetic Flux Meter, 0-500 Tesla , Meggar, Analog-500V , Ac Starters:- Resistance Type Starter, For A.C Motors Of 2 To 5 H.P. , Ac Starters:- Star Delta Starter–Semi Automatic, For A.C Motors Of 2 To 5 H.P. , Ac Starters:- Star Delta Starter- Soft Starter, For A.C Motors Of 2 To 5 H.P. , Oscilloscope Dual Trace, 20 Mhz , Temperature Controlled Soldering Iron, 50-Watt, 230 Volt , Immersion Heater,1500Watt,240V , Motor Pump Set,1Hp,1Phase,240V , Oil Testing Kit, Oil Testing Kit, 230V,Singlephase50 Hz 60 Va Output 0-60 Kv Variable , Inverter With Battery, 1 Kva With 12 V Battery Input- 12 Volt Dc, Output- 220 Volt Ac , Dc Power Supply, 0 - 30 V, 5 A , Potential Transformer,415V,50Hz,Ptratio,440V/110V, 10 Va , Ac Phase-Wound Slip Ring Motor With Starter Switch, 5Hp,440V,3Phase,50Hz , Universal Motor With Starter/Switch, 240V,50Hz,1 Hp , Three Phase Transformer, Shell Type Oil Cooled With Delta/ Star, 3 Kva , 415/240 V, 50 Hz , Diesel Generator Set With Change Over Switch, Over Current Breaker And Water/ Air-Cooled With Armature, Star-Delta Connections Ac 3 Phase ,7.5 Kva, 415 Volt Or Higher Rating , Used Dc Generators-Series Type For Overhauling Practice , Used Dc Generators- Shunt Type For Overhauling Practice , Used Dc Generators -Compound Type For Overhauling Practice , Ceiling Fan Coil Winding Machine, 250V, 50 Hz, 1-?, With Speed Control , Shaded Pole Motor, Fractional Hp, 240V,50 Hz , Smart Meter,1Phase-Smart Energy Meter , Smart Meter,3Phase-Smartenergymeter , Ev Charger, 3Phase Input , Ev Charger (Home), 1Phase Input , Supply Of Short Fall For Turner Trade Course , Surface Plate - Granite, 1000 X 1000 Mm With Stand And Cover , Marking Table (Ci), 120 X 120 Cm With Stand And Cover , Micrometer Inside, Upto 25 To 50 Mm, Least Count 0.01 Mm With Nabl Accrediated Lab Certificate , Vernier Caliper Outside, Inside And Depth, 200Mm / 8 Inch With Metric And Inch Scale (Lc=0.02Mm) With Nabl Accrediated Lab Certificate , Dial Vernier Caliper, 200Mm , Least Count 0.05Mm With Nabl Accrediated Lab Certificate , Vernier Bevel Protractor, 300Mm Blade With Nabl Accrediated Lab Certificate , Vernier Micrometer, 0- 25 Mm O/S Lc=0.001Mm With Nabl Accrediated Lab Certificate , Gauge Feeler, Thickness - 0.05Mm To 0.3 Mm By 0.05 Mm-13 Leaves , Gauge Feeler, Thickness -0.4Mm To 1Mm By 0.1Mm -13 Leaves , Gauge - Radius Set, 1Mm To 25Mm By 0.5Mm , Drill Angle Gauge, 45 Degree, 55 Degree, 90 Degree , Magnifying Glass, 75Mm With Magnifying Factor 10X , Plain Ringgauge, 12,16,20,25,30,32,36,40,45,50 Mm , Plainplug Gauge, 12,16,20,25,30,32,36,40,45,50 Mm , Tap &Die , Ba No 0 To 10 In A Box , Tap &Die Set, Metric - 3 To 24 Mm , Tap &Die , Bsf Upto 1 Inch , Tap &Die, Bsw Upto 1 Inch , Angle Plate, Adjustable - 150 X 175 X 250 Mm , Tool Makers Button , Hand Chaser With Handle, M-12 & M-16 (External) , Hand Chaser With Handle, M-12 & M-16 (Internal)
|
