|
Tender For Addn/Altn To Qtr At Bhagat Road, Fafa Under Ge (W) Jalandhar Cantt; 1 Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete all as spd and directed . 2 Demolition of brick or stone masonary built in cement mortar complete all as spd and directed. 3 Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc 4 M&L brick work with sub-class B bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6 complete all as spd and directed 5 M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed. 6 M&LCement concrete type D 2, 1:4:8 (using 40 mm gradedstone aggregate) in sub base of flooring, hard standing,Manhole, drain etc. 7 M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions ofwalls shallnot exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls complete all as spd and directed. 8 M&L 10mm thick rendering in CM 1:3 onbrick/concrete surfaceas in ceiling and finishing the surface even and smooth with out using extra cement. complete all as spd and directed. 9 Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered;and scrubbing down with water etc. to receive plaster, walls are built in cement or cement lime mortar.complete all as spd and directed. 10 M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement complete all as spd and directed. 11 M&L 15mm thick rendering on wall in CM 1:6 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement complete all as spd and directed. 12 Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises complete all as spd and directed. 13 M&L colouredGlazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4 complete all as spd and directed. 14 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as spd and directed. 15 M & L for applying neat cement slurry with 3.0kg of cement per sq. metre complete all as spd and directed. 16 M & L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqMinfloors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. complete all as spd and directed. 17 M&L Machine cut kota stone slab flooring 18 - 20mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete all as spd and directed. 18 M&L Machine cut kota stone slab flooring 18 - 20mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete all as spd and directed. 19 Demolition of re-inforced cement concrete of any description and in anypositionnot otherwise specifically provided for complete all as spd and directed. 20 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as spd and directed. 21 M & L for Reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) (nominal mix) inSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd and directed. 22 M&L mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432 complete all as spd and directed. 23 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortercomplete all as spd and directed. 24 M&L 20mm Granite (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed. 25 Rounding/mouldingto edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc complete all as spd and directed. 26 M&L for 15mm thickrenderingin1:3 CMwith water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc as in sunken portion complete all as directed. 27 M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per sqmincluding cleaning surfaces.complete all as directed. 28 M&L APP based polymeric membrance minimum weight not less than 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) land on primed surface by forced application(complete area sealed by gas flame)with over lap of 15 cm complete all as specified and directed complete all as spd and directed. 29 M& L Cement concrete type E-2, 1:5:10 using 40mm graded brick aggregate in foundations filling and mass concrete as in sunken floorcomplete all as spd and directed. 30 Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall, complete all as spd and directed. 31 M & L for 50mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item) complete all as spd and directed. 32 Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm eachcomplete all as spd and directed. 33 Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm eachcomplete all as spd and directed. 34 Taking down shutters any description exc 1 sqm but n.exc 2sqm each and all as specifiedand directed . 35 Taking down shutters of any description not exc 1 Sqm and not exc 2 sqm each and refixing in same opening after necessary all repairingcomplete all as spd and directed. Note : Change of old wiremesh will be measured in connected supply only items. 36 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm complete all as spd and directed. 37 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm complete all as spd and directed. 38 M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articlescomplete all as spd and directed. 39 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x 100 mm, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 40 Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. 41 Cutting holes in brick walls incement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brickcomplete all as spd and directed. 42 S&F2nd class hardwood rail and style, factoy made plain,framed,panelled shutters (two panel) 35mm thick, with lock rails and panel of 9mm B. W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS : 1003 (Part-I), kiln seasoned and chamically pressure treatedcomplete all as spd and directed. 43 S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numberscomplete all as spd and directed. 44 Dismantling of unframed timber scantlingsin fillets, rails, posts, rafters, purlins,etc. under 40 sq. cm in section in any positioncomplete all as spd and directed. 45 Dismantling boarding, any description, fixed in any position with nailsComplete all as spd and directed. 46 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size Frame size 50 x 100 mm for wardrobe, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 47 S & F Factory Made Solid PVC Moulded Door Shutter With Core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawingcomplete all as spd and directed. 48 Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube 49 S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out ofM.S.Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame at the site as per specification & drawing. 50 M & L Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding window shutters including providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and the directions of Engineer-in-charge. 51 S & F powder coated of any colour (Thickness or powder coating not less than 50 micron).aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1 no.)complete all as spd and directed. 52 S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165complete all as spd and directed. 53 S&F Galvanisedmild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staplescomplete all as spd and directed. 54 M&L for 4.80mm thick sheet glass ordinary quality glazing with oil puttyin squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. 55 Supply only Galvanisedmild steel wire cloth, 0.56mm nominal dia of wire and any width of aparture 1.18mm fixed with alu wire staples fixed to wood/steel framescomplete all as spd and directed. 56 S&F Butt hinges, medium weight cold rolled 100 mm size ISI markedcomplete all as spd and directed. 57 S&F aluminium anodised barrel tower bolts of extruded section 150mm longcomplete all as spd and directed. 58 S&F Extruded aluminium alloy handles fabricated type anodised 150mm sizecomplete all as spd and directed. 59 S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified. 60 S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller platecomplete all as spd and directed. 61 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mmcomplete all as spd and directed. 62 S & F in repair for mild steel pipe 25 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops,rollers etc as approved complete all as specified. 63 S&F in replacement 100 mm hasp and staple aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified. 64 Providing and fixing solid PVC Kitchen Cabinet of size 1845 x 770 x 620mm at site made out of 18mm thick one side decorative lamination and other side balancing lamination sheet consisting of car case 18mm thick pvc sheet and provision of shutter made out of 18mm thick one side decorative lamionated PVC sheet all required brackets SS screw etc. the panel shall be febricated using adhessive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification mentioned as per drawing and specification approved by Engr in Charge. 65 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45x 70 mm for kitchen shelf, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 66 Providing and fixing factory made 18mm thick solid, decorative, WPC(Wood Polymer Composite) laminated board of required size as in shutter comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner with having minimum density not less than650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. 67 Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc.including welding grinding,buffing,polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fasteners,stainless steel bolts etc,of required size, on the top of floor or the side of waist slab with suitable arrangementcomplete all as spd and directed. 68 Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 69 Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 70 S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 71 Refixing 15mm old GItubing and connections in new or old position (Walls, ceiling, floors, etc.)complete all as spd and directed. 72 S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 73 Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)complete all as spd and directed. 74 Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar1:3 to ends or edges of shelves , for water tubing etc andmaking good, cutting exc 10cm girth but not exc 20cm girth in stone wallscomplete all as spd and directed. 75 Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittingscomplete all as spd and directed. 76 S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I complete all as spd and directed. 77 Disconnecting existing tanks, setting aside (or loweringif required)for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning of over head tank 500ltr capacity of any description and capacity, descaling, washing with detergent powder, removing vegetation around the over head tank/plat form complete all as specified and directed. 78 S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as spd and directed. 79 S&F ball float valve brass with epoxy coated aluminimum rodfor 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe in repair. complete all as spd and directed. 80 S&F in repair 15mm dia long body Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule complete all as spd and directed. 81 S&F in repair 15mm brass CP bath mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete all as spd and directed. 82 S&F in repair 15mm brass CP WHB/Sink mixer swan neck for mixing hot & cold water screwed down for iron pipe and fixed.complete all as spd and directed. 83 S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. complete all as spd and directed. 84 S&F 15mm dia Brass stop valves chromium plated, fancy type with cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlons as specified and fixed in repairs. 85 S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers including taking old one in repaircomplete all as spd and directed. 86 S&F in Vitreous china corner wash hand basin (385X385X150mm) white, angular back excluding taps,including brackets &32mm waste cuppling complete all as specifed and directed. 87 S&F Vitreous China wash down Water closet pan (pedestal pattern) with plastic water closet seatcover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairscomplete all as spd and directed. 88 S&F Vitreous China Water closet (Squatting pattern) Orissa Pattern size 580x 440 mm white with P or S trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairscomplete all as spd and directed. 89 S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairscomplete all as spd and directed. 90 S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified in repair. complete all as spd and directed. 91 S&F in toilet paper holder of brass chromium platedfixed to walls with brass screws complete all as spd and directed. 92 Supply and fixed CP Soap dish, any type fixed to walls with plugs with chromium plated brass screwscomplete all as spd and directed. 93 Supply and fixing for glass Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 450mm x 150mm complete all as specified and directed. 94 S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. 95 Supply and fixing for glass Corner Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 12 dia complete all as specified and directed. 96 S&F Health faucet mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified. 97 M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed. 98 S&F in replacement CP grating 100-125mm dia circularof approved make and fixing with cement mortar 1:3 on Nahani Trap or floor trap complete all as specified. 99 S&F in repair brass chromium plated shower rose 125mm size complete all as spd and directed. 100 Supply in fixing in repairs sink with drainage board made Stainless steel 1mm thickkitchen or laboratory with plugs, washer and wastes pipe , including bedding in cement mortar on dwraf wall orincluding fixing cantilever brackets and connecting union pipe, over all size 915mm x 460mm bowl size 410mm x330mm x160mm.complete all as spd and directed. 101 S & F in replacement stainless steel kitchen plate rack, made out of 1mm thick stainless steel size 30 x 24 x 10 (Miinimum weight 7 Kg) with shelves and plate position as approved complete all as specified and directed. 102 Dismantlingof brick tiles single layer as in roofcovering complete all as specified 103 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof)complete all as spd and directed. 104 Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd. 105 (i) M&L for providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges and PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40,with using water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc,finishing the surface even and smooth without using extra cement complete all as specified. 106 (ii) M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement (iii) Providing and applying Epoxy primer (02 fast component resin of hardner) on the prepared surfacev @200gm per Sqm.(iv) Providing and applying Liquid Polyurea - PU based hybrid elestomeric water proofing membrane at existing/newly constructed roofs. Double coat is required on the smooth and cleared surface @ 1.50Kg per Sqm. (v) After coating of primer of two coats of ULTRON (US) a proper protective plaster/layer is to be done by laying Geo textile and 40mm screed on the top of final coating. (Make - Asian Paints, BASF & SIKA) Note:- Ser No (i) to (v) : The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm. 107 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)complete all as spd and directed. 108 Dismantling of cast iron or reinforced concrete drain pipes of size 75-100mm dia, jointed in cement mortarandtakingout of trenches, if required.complete all as spd and directed. 109 S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to wallscomplete all as spd and directed. 110 S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wallscomplete all as spd and directed. 111 S&F110mmPVC (SWR) bendscomplete all as spd and directed. 112 S&F75 mmPVC (SWR) bends complete all as spd and directed. 113 S & F for PVC 110mm (SWR) vent cowlcomplete all as spd and directed. 114 M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applyingtwo coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge. (Note : Cost of form work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. 115 Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etcfor shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soilcomplete all as specified and directed. 116 Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed 117 M &L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed 118 M&L for concrete bed for 150mm in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and testedcomplete all as specified and directed. 119 Cutting into existing manholes for connecting new drains making good to open and rendering, cutting out existing benching for and forming branch channel 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1,smooth finished and reforming benchingcomplete all as spd and directed. 120 Demolition of re-inforced cement concrete of any description and in anypositionnot otherwise specifically provided forcomplete all as spd and directed. 121 M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks ,drain,covers including all form work and setting in CM 1:4 all as specified and shown on drgs. 122 M&L mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432complete all as spd and directed. 123 Material and labour for cement concrete 1:2:4 Type B-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge. 124 M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 125 M & L for applying one coat of synthetic enamelled paintincluding preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 126 M & L for applying two coat of synthetic enamelled paintover one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 127 M & L for applying one coat of synthetic enamelled paintincluding preparation of old decoratedsteel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 128 M & L for applying white wash of 3 coats on ceiling incl preparation newly plastered surfaces as specified and directed. 129 Complete removal of existing treatment andapplying Two coat of white wash on ceiling incl preparation old plastered surfaces as specified and directed. 130 M & L for applying white wash of 3 coats on wallsincl preparation newly plastered surfaces as specified and directed. 131 Complete removal of existing treatment on wall andapplying Two coat of white wash incl preparation old plastered surfaces as specified and directed. 132 Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified. 133 Complete removal of existing treatment on wall andapplying Two coat of Oil distemper (white or tinted) on old plastred surfaces incl preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engineer-in-Charge. 134 Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paintover one coat of cement primer complete all as specified. 135 Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/ lose soilcomplete all as spd and directed. 136 Excavation in post holes each nexc 0.50 cum , getting out, returning filling in and ramming earth or broken rubble mixed with earth in layers not exceeding 25cm in soft/loose soilcomplete all as spd and directed. 137 M & L for PCC (1:2:4) typeB-2 (using 40mm graded crushed stone aggregates ) lean concrete as in foundation, filling and mass concrete of post complete all as specified . 138 M&L Broken stone or boulders as in hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered, rammed to a true surface etc complete all as specified and directed 139 M/L 100mm thick cement concrete 1:4:8, type D-2 using 40mm graded stone aggregatecomplete all as spd and directed. 140 M & L for 25mm thick Sand coushening under paver block complete all as specified and directed. 141 M&L machine pressed precast coloured concrete coloured interlocking paver blocksany shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment.complete all as spd and directed. 142 M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm gradedstone aggregate) cast in situ inkerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work.complete all as spd and directed. 143 S&F Steel work as in tubular section for Post, Purline etc including special shaped washer , angle cleat, holdfast, gussete plate etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240cut or notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (incl rivet or nut and bolts) providing and fitting angle cleats Gussete plates etc also for welding plumbing, truing up and fixing complete as directed by Engr-in-Charge. 144 M&L pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 145 M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 146 M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters,nosingtosteps includingembedinginconcrete and screwing etc. wind ties for roofincluding securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165complete all as spd and directed. 147 M&L for prepration of new steel surface of any description, over 10cm in width or girth,not otherwise described and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc complete all as specified and directed. 148 M & L for prepration of new steel surface of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc. complete all as spd and directed. 149 Returning, filling in , including spreading, levelling , watering and well ramming in layers not exc 25 cm thick by using hard/dense soil as in low line area as directed by Engr-In-Charge . 150 Removing excavated soils n.exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.complete all as spd and directed. 151 Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors 152 Taking down unserviceable Submain/Cableof any size as directed by Engineer-In-Charge. 153 Taking down main switch / DB as directed by Engineer-In-Charge. 154 M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn throughand including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length) 155 M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistrandedcable as earth wire including sunken type pressed steel terminal boxes of thickness 1.6 mm thick and plastic laminated white / coloured top sheet cover 3.0 mm thick for: complete all as spd and directed. 156 One light / fan/bell pointcontrolled by one, one way switch. complete all as spd and directed. 157 One 3 pin socket out let 5 Amps on same board with other switches.complete all as spd and directed. 158 One 3 pin socket out let 5 Amps on the independent board.complete all as spd and directed. 159 Dittoall as per item No.5 about but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent boardcomplete all as spd and directed. 160 S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, ACcomplete all as spd and directed. 161 S & F switch Piano 1 5 Amps, flush button type, SP, one way, 230 Volts, ACcomplete all as spd and directed. 162 S & Fsocket out let multipurpose 5 pin 5 Amps,230 Voltscomplete all as spd and directed. 163 S & Fsocket combination ,6 pin ,15 amps, flush type, multipurpose, 230 Vcomplete all as spd and directed. 164 Supply and fix bell push flash piano type 5 amps.complete all as spd and directed. 165 Supply and fix bell ding dong 230 Volts AC single pole.complete all as spd and directed. 166 M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. 167 Supply and fix DB,double door,SPN 8 way for MCB, 240 volt with 200 amps rated bus bar.complete all as spd and directed. 168 S & F MCB SPN40 to 63 Amps 240 voltscomplete all as spd and directed. 169 S & F MCB SP 6-32 Amps 240 voltscomplete all as spd and directed. 170 Supply and Fixingstepped socket type electronic fan regulator and connecting up complete all as directed by Engineer-In-Charge. 171 M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings.complete all as spd and directed. 172 S&F in replacement LED tube light fitting 20Wbox type including LED lamp 20 W with 2200 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixturesand connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. 173 Supply & fixing in replacement LED street light fitting 35W including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed including bracket and fixing clamps etc.complete all as spd and directed. 174 Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holderconnecting up with three core flexible copper conductor cable of suitable size all as specified and directed. 175 Taking down existing Ceiling fan/Exhaust fancapacity/type carefully and refixing the same with gutties, nuts boltss if required complete all as specified and directed. 176 Taking down existing Geyser any capacity/type carefully and refixing the same with replacement of PVC connection/Steel connection and anchor fastenerpipe if required complete all as specified and directed. 177 Supply and laying GI Tube Med grade 50mm dia all as specified and directed. 178 Supply and fix MCCB 63 Amps 4 pole415 Volt,16 KA breaking capacity . complete all as spd and directed. 179 M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DBby means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part Icomplete all as spd and directed. 180 M& L for XPLE UG Cable of size 35 Sqmm 4 Core all as specified and directed. 181 M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10m all as specified and directed.only punned thickness will be measured.complete all as spd and directed. 182 Supply and lay burnt bricks sub class B standard size laid across the cable in trenches as protection to the cable all as specified and directed.
|
