|
Tender For Special Repairs To Bldg No C/13/227 At Mh Panagarh Under Ge Panagarh; 1 Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. 2 M&L for cement concrete 75 mm thick type B- 1, 1:2:4 (20 mm graded aggregate) laid on concrete floors and pavings; laid over cement concrete sub floors etc. and finished to an even and rough surface as specified and as directed by EngR-in-charge. (Note: Reinforcement will be measured and paid separately) 3 Dismantling wall and ceiling board of any descrition complete all as specified and directed. 4 S&F 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3as in moduler shutters/cabimet drawercupboard cabinet shutterincluding all frame work as specified and directed by Engr-in-Charge 5 S&FAuto Closing Clip-on Soft Close Hinges with Mounting Plate (Eccentric) (L Bihari ) complete all as specified and directed. Make :Hettich/Ozone/Godrej 6 S&Fmagnetic catches with ferrite magnet complete all as specified and directed. Make :Hettich/Ozone/Godrej 7 S&F in repairs soft close telescopic channel of size 550mm suitable for load capacity of 35 Kg complete all as specified and directed. Make :Hettich/Ozone/Godrej 8 S&F Stainless Steel Pull Handles (SS Grade-304) 200mm long H type, 22mm dia. Make ; Hettich/Ozone/Godrej 9 S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, size of grid 605 x 605mm complete all as specified and directed. 10 S&F Anodised powder coated aluminium snap grid frame work for false ceiling ( size of grid 605x605 mm) complete all as specified and directed. 11 S&F Non asbestos fibre cement designer building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceilingcomplete all as specified and directed. 12 M&L for 300mm thick Kankar or laterite,with mix of fly ash ,clinker & stone dust in the proportion of 1:3:6 ( i.e. 10% fly ash,30% clinker & 60% stone dust ) laying in layers n.exc 100mm thick ,spread, rolled and consolidated to gradient and camber required, watering ,ramming and compactedcomplete all as directed by Engg-in-charge . 13 Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed. 14 M&L for rendering 15 mm thick in CM 1:4 on fair face of brick work surfaces or concrete finished fair and even with using WPC compound (if directed), complete all as specified. (Note: WPC will be measured and paid separately) 15 Supply only liquid Water proofing compound complete all as specified and directed. 16 M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces , complete all as specified and directed. 17 M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including complete removel of existing treatment complete all as specified and directed 18 M&L for rendering 15 mm thick in CM 1:6 on other fair faces of brick work surfaces finished fair and even complete all as specified and directed 19 M&L for preparation of new surfaces of plastered wallsand applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (2.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed. 20 Complete removal existing finishes and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (2.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed. 21 Dismantling wrought iron or mild steel workof any description not otherwise provided, for rusted members of steel trusses/ purlins, complete all as specified and directed 22 S&F mild steel as Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-410-W(Gde-E-250) quality-B, complete all as specified and as directed. 23 S&F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) of Fe 410-W(GdeE- 250) quality "A" forming holes, without any attachment complete all as specified and directed. 24 M&L for complete removal of existing treatment and applying two coats synthetic enamel paint over a coat of red oxide zinc chrome primer incl preparation of surfaces over 10 cm width or girth complete all as specified and directed 25 M&L for two coats synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed 26 Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed 27 M&L for sheet glass 5.5 mm thick ordinary quality and glazing with rubber gasket and pin in square n.exc 0.50 sqm in each pan complete all as specified and directed 28 M&L for frosted sheet glass 5.5 mm thick ordinary quality and glazing with rubber gasket and pin in square n.exc 0.50 sqm in each pan complete all as specified and directed 29 M&L for sheet glass 5.5 mm thick ordinary quality and glazing with rubber gasket and pin in square exc 0.50 sqm in each pan complete all as specified and directed 30 S&F 3mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed. 31 S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm andfixed with tinned stacks or galvanised wire staples, complete all as specified and as directed. 32 Demolition for brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, facings, dressed stonework and precast concrete articles and removal or rubbish off the site complete all as specified and directed. 33 M&L for brick work with fly ash old sized bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed. 34 M&L for brick work with flyash bricks straight or corve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed. 35 M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed 36 All as per Item No 35.00 above, but but 6mm to 8mm dia, complete all as specified and directed. 37 All as per Item No 35.00 above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed 38 M&L for Use and Waste of Formwork(steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) for fair finsihed surfaces complete all as specified and directed 39 M&L for Use and Waste of Formwork(steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed 40 M&L for Use and Waste of Formwork(steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed 41 M&L for Use and Waste of Formwork(steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to chullah hoods, chajjas, troughs and similar items including edges, complete all as specified and directed 42 Demolition of RCC(other than ground floor) pillar, beams landing, chajjas, slab shelves & similar suspended work (reinforcement cut as required to facilitate demolition) and removing unseviceable material complete all as specified and directed 43 M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed 44 M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed 45 M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) asin Chajjas complete all as specified and directed 46 M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed 47 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed 48 M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. 49 M&L for light shade vitrified ceramic tiles 8-9mm thick (square /rectangular ) polished , area of each tiles not exceeding 0.36 Sqm, in floors etc setand jointed in neat cement slurry andpointed flush in white or colourcement with pigmentover and including 15mm thick cement mortar 1:6 screed bed in double charge complete all as specified. 50 M&L for Glazed ceramic tiles in vertical surface 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including C:M (1:3) back coat of mortar 10 mm thick for laying skirting/dado"s wall tiles complete all as speciified and directed. 51 Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etccomplete all as specified and directed 52 M&L for 18-20 thick Granite work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over 20mm thick screed of CM 1:3 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed 53 Taking down chowkats or frames with shutter w/o taking off shutter from the framen exc 1.5 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed by Engr-in-charge. 54 Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm & n. exe 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge. 55 Taking down shutters of any description n. exc 1 sq. m each complete all as specified and directed by Engineer-in-Charge 56 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. 57 S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. 58 S&F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed 59 S&F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed complete all as specified and directed 60 Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including aluminium snap beading for glazing/ paneling,all complete as per architectural drawings and the directions of Engineer-in-Charge. 61 S&F powder coated Anodised aluminium windowshutters, sliding type without sash bars, (minimum thickness of powder coating 50 micron) for three track shutters of windows & ventilators aluminium sections weighing 0.55 kg/m including necessary joining cleats , Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, anodised aluminium fittings suitaibleetc all complete as per architectural drawings and the directions of Engineer-in-charge. 62 S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed 63 S&F in repairs, door closer aluminium body, hydrailically regulated, designation No.2, universal type, suitable for door shutters and weight between 36 to 60 kg and fixed complete all as specified and as directed. 64 S&F40mm wide and 5mm thick PVC door seal (snake guard) with powder coated aluminium frame complete all as specified and directed 65 M&L for 4mm thick ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame work all as specified and as directed. 66 S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm c/c, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engr-In-Charge. 67 M&L for framed work such as grills etc with ends of bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. 68 M&L for PCC(1:3:6) type C-1 (using 20mm graded aggregate) as in bed blocks for hold fast including necesssary formwork complete all as specified and directed 69 S&F mild steel flat iron as in hold fast, clamps articles conforming to FE 290 Gde-E-165 complete all as specified and directed. 70 M&L for repairs to crack portion with jacketting technique, taking down the existing plaster up to the brick wall surface of min 200mm wide, cleaning the loose particles on surface of brick work along the length of the crack and filling the gap/crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate up to brick surface and inserting the welded mesh of size 25X25X2mm along the crack on both sides of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling mechanism through the full width of the wall @25cm c/c and insert 8/10mm dia rod in the drilled holes, welded with horizontal rod to with-hold the welded mesh and applying grit plaster 1:1:2 using 4mm and down aggregate finished even and smooth without using extra cement complete all as specified and directed. Note: reinforcement and welded mesh will be measured and paid separately. 71 M&L for 75mm thick PCC 1:3:6type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement, incl making joints 10mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with and incl bitumen and sand 1:3 by weight complete all as specified and directed. 72 M&L for 75 mm thick cement concrete Type D2, 1:4:8 (using 40 mm graded stone aggregate) as in sub bases complete all as specified and directed 73 S&F 100 mm size butt hinges extruded aluminium alloy with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed 74 S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed 75 S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed 76 Taking down steel tubing having bore of pipe 15 mm and connections, including cleaning for refixing or removal to store complete all as specified and directed 77 Taking down steel tubing having bore of pipe 20 mm and connections, including cleaning for refixing or removal to store complete all as specified and directed 78 S&F for 16 mm outer diaCPVC pipe with CPVC brass treaded fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. 79 S&F for 20 mm outer diaCPVC pipe with CPVC brass treaded fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. 80 S&F gate valves 20 mm bore dia with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 81 S&F in repair bib taps of 15mm bore fancy type, chromium platedcast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed. 82 S&F in repairs vitreous china squatting pan, "Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. 83 S&F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. 84 S&F table top vitreous china wash basin, white, flat back, size, 630X450mm including all fittings and fixtures(waste coupling, bottle trap, etc), complete all as specified and directed. 85 S&F in repair White glazed fine clay sink size 750x450x250mm excluding taps, waste, chain and plug and porcelain stopper but including bracket, complete all as specified and directed. 86 S&F in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed. 87 S&F in repairPillar taps (Swan Neck) fancy type 15mm borecast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed 88 S&F PVC corrugated waste pipe 32mm dia for wash basin 1150mm long complete all as specified and directed 89 S&F in repair 32 mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms complete all as specified and directed 90 S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white minimum), with grating and union for discharge pipe(back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed 91 S&F in repair 32 mm bore Waste coupling of PTMT (half or full threaded) suitable urinal. (Minimum weight 32mm45gms/40mm-60 gms complete all as specified and directed 92 S&F in repair PVC connection 15 mm size PTMT nuts of length ength 600 mm complete all as specified and directed 93 S&F in repair soap dish vitreous china white size 160x160x90mm approx all as directed by Engineer -in-Charge 94 S&F in repair toilet paper holder, vitreous china box type, coloured fixed to wall with chromium plated brass screws complete all as specified and directed 95 Supplyand fix in repair angle/stop valve of 15mm bore , chromium platedwith long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrulecomplete all as specified and directed. 96 S&F in repair grating square 100mm size of CP (minimum weight 100 gms) complete all as specified and directed 97 S&F grating square with waste hole 100mm size of PTMT(minimum 100 gms) complete all as specified and directed 98 S&F in repair 125mm BrassChromium Plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed 99 S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 100 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified 101 S&F in repairs Drapery rod (conduit) of dia not less than 25 mm having a corrugated virgin PVC extrusion on it& finials of approved shadecomplete all as specified and directed 102 S&F MS PVC sheeted/power coated bracket size 150mm made to shape suitable for holding curtain/drapery of rod of 25mm dia fixed with PVC rawl plugs and MS steel screws complete all as directed by Engr-in-Charge and as per approved sample kept in AGE B/R 1 office for single/double rod system complete all as specified and directed 103 S&F for coloured conical end balls dia not less then 50mm and PVC coated made to shape suitable for fixing as end of curtain/dropery rods complete all as directed Engr-in-Charge and as per approved sample kept in AGE B/R 1 office complete all as specified and directed 104 S&F in repairs for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. 105 S&F CP tubular towel rail 20mm dia D type 60cm between two flanges complete all as specified and directed by Engineer -in-Charge. 106 Excavating over areas, n exc 1.5 m deep and getting out soft/ loose soil complete all as specified 107 Taking down rain water pipes (any size or pattern) , including all fittings and removal off the site complete all as specified and directed. 108 S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with clamps and jointed complete all as specified and as directed by EIC. 109 All as per item No 108.00 here-in-above but 75 mm bore complete all as speified and directed. 110 S&F in repair 110mm bore PVC (SWR) bends any radiuswith access door complete all as specified and as directed by EIC. 111 S&F in repair 75mm bore PVC (SWR) bendsany radius with access door complete all as specified and as directed by EIC. 112 S&F in repair PVC (SWR) vent cowl 110 mm bore complete all as specified and directed 113 M&L for RCC precast cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate)as in cover slab for manholes and similar article with plain face set in CM (1:4) complete all as specified and directed (Note: Reinforcement will be measured and paid separately) 114 M&L for PCCtype D2 1:4:8 using 40 mm graded aggregate in foundations, fillings and mass concrete complete all as specified and directed. 115 Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed. 116 M&L for 160mm bore,HDPE double wall corrugated(DWC)SN-8PIPE (HDPE Black Pipe) WITH COUPLER Conforming to IS:16098 Part-II:2013 sewage pipes laid in trenches and jointed as per manufacturer,s instruction with and including all fitting complete all as specified and as directed. 117 M&L for cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains for benching complete all as specified and directed 118 M&L for extra for forming fair finish drain channel upto 30 cm inner grith in cement concrete using extra cement complete all as specified and directed 119 M&L for extra for forming fair finish drain channelinner girth exc 30 cm but not exc 45 cm in girth in cement concrete using extra cement complete all as specified and directed 120 M&L for cement concrete type C-1 1:3:6 (using 20mm graded stone aggregate) in cills, steps, plinth courses, string courses, lacing courses, parapets, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed rounded or chamfered on edges complete all as specified and directed 121 M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including plaster, buttresses, columns, pillars, boundary pillars and posts ( including cap and bases) including necessary formwork complete all as specified and directed by Engr-in-Charge. 122 E/M PORTIONTaking down carefully aluminium conductor point wiring (light,fan,socket or power) completeincluding fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing(except those to be reused shall be kept in safe custodyat the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. 123 M&L for concealed point wiring for fan/light point controlled by one one way switchcomplete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour)and connected to common earth dollyincluding sunken in GI terminal box2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets for the following:-Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surfaceare deemed to be included in the quoted rate. 124 All as per item No. 123.00 here-in before but5 Amp socket on same boardwith other switches. 125 All as per item No. 123.00 here-in before but5 Amp socket on Independent boardwith other switches. 126 All as per item No. 123.00 here-in before but5 Amp Calling bell pointwith other switches. 127 All as per Item No. 123.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.5 Sqmm for one socket point of 3 pin 5 Amps on independent board including FRLSH grade (ISI mark), PVC insulated,unsheathed onerun multi-stranded copper conductor of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. 128 All as per Item No. 123.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one socket point of 3 pin 5 Amps on independent board including FRLSH grade (ISI mark), PVC insulated,unsheathed onerun multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. 129 S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed by Engr-in-Charge 130 S&F Bell switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed by Engr-in-Charge 131 S&F socket outlet 2 in 1 multipurpose5 pin , (6 Amp ) flush typecontrolled by one switch duly marked complete all as specified and directedby Engr-in-Charge 132 S&F switch socket combination 2 in 1 multipurpose5 pin , (6 Amps) flush typecontrolled by one switch complete all as specified. 133 S&F switch socket combination2 in 1, 6 pin, (16 Amps ) flush typecontrolled by one switch complete all as specified. 134 S&F Buzzer, Ding dong, AC 230 Volts, single pole 230 volts all as specified and directed. 135 S&F ceiling rose surface bakelite 45 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified by Engr-in-Charge 136 S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified by Engr-in-Charge 137 S&F lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings complete all as specified. 138 S&F sheet metal enclosure with 20 Amp Mcb and two pin and earth plug and socket complete with one single pole MCB all as specified by Engr-in-Charge 139 S&F for concealed type sub main wiring with two run of 10.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 10.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCconduitand one run of cutting chases shall be measured as unit length. (ii)Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 140 S&F for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCconduitand one run of cutting chases shall be measured as unit length. (ii)Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 141 S&F for concealed type sub main wiring with four run of 10.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 32mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including two run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 4 runs of line conductor,one run of earth continuity conductor, two run of PVCconduitand one run of cutting chases shall be measured as unit length. (ii)Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 142 S&F in repairs LED security light 35 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 110 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as perlatest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz,protection grade IP 66, IK-08 CRI greater than or equal to 70%, CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wireof 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified.Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However,as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked "Date of installation" and "Date of Procurement" with marker pen 143 S&F in repairs LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable . 144 S&F in repairs LED 9/10 Watt tube light fittingintregatedtype, includingLED retrofit tubelamp 9/10 W , LED tube light nominal power 9/10 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingcomplete all as specified & directed. Note (i) Make of batten and LED tube lamp should be of same make. 145 S&F in repairs LED 20 Watt tube light fittingintregatedtype, includingLED retrofit tubelamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingcomplete all as specified & directed..Note (i) Make of batten and LED tube lamp should be of same make. . 146 S&F recess mounting luminaire (PANEL LIGHTING) with high performance LEDs, suitable for mounting withArmstrong/Grid ceiling Fixture size: (LxW) in (600 x 600) mm LED 40/42 Watt with CRCA powder coated housing (white after phosphochromate treatment) High efficiency long life LED package in integral module with lumen efficacy of >120 lm/W and viewing angle of 120° to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per IS:15885 Part 2/Sec 13. operational voltage of 170 volts to 270 volts, frequency of 50 Hz,protection grade IP 20, CRI greater than or equal to 80%,THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core,including taking down old unserviceable complete all as specified & directed: 147 S&F in repair LED light fitting 12 watt recessed round polycarbonate housing down lighter with superior light output as per existing size and shape , LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz,lumen efficacy of minimum 110 lumens per watt, isolated electronic LED driver (SMPS based constant current supply) with output short circuit protection, over voltage protection, surge voltage protection upto 2 KVs, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, ITHD below or less than 15%, CW available CCT of 5700K, power factor of minimum 0.95, CRCA powder coated white after phosphochromate treatment housing, life span of minimum 50000 working hours including making electric connection from source with PVC sheathed copper conductor wire of 1.5 Sqmmx 3 core complete all as specified and directed by EIC. 148 S&F in repair LED light fitting 6 watt recessed round polycarbonate housing down lighter with superior light output as per existing size and shape , LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz,lumen efficacy of minimum 110 lumens per watt, isolated electronic LED driver (SMPS based constant current supply) with output short circuit protection, over voltage protection, surge voltage protection upto 2 KVs, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, ITHD below or less than 15%, CW available CCT of 5700K, power factor of minimum 0.95, CRCA powder coated white after phosphochromate treatment housing, life span of minimum 50000 working hours including making electric connection from source with PVC sheathed copper conductor wire of 1.5 Sqmmx 3 core complete all as specified and directed by EIC. 149 S&F Heavy duty exhaust fan(in metalic Body) 300 mm in Sweep, 1400 RPM single phase A/C 230 volts with louvers (incl making of hole in wall grouting nut, bolts in wall making good disurbed surfaces etc) all complete as specified and directed 150 S&F Heavy duty exhaust fan(in metalic Body) 450 mm in Sweep, 1400 RPM single phase A/C 230 volts with louvers (incl making of hole in wall grouting nut, bolts in wall making good disurbed surfaces etc) all complete as specified and directed 151 S&F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 12 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge 152 S&F in repairs VTPN distribution board with provision for 4 pole MCCB up to 160A as incomer with three phase and single phase (TP/SP) MCB outgoing with and including insulated busbar (tinned electrolytic copper) arrangement, shrouded neutral bar and earth bars, Top and bottom removable gland plates with knockouts, 6 way,Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge 153 S&F in repairs VTPN distribution board with provision for 4 pole MCCB up to 160A as incomer with three phase and single phase (TP/SP) MCB outgoing with and including insulated busbar (tinned electrolytic copper) arrangement, shrouded neutral bar and earth bars, Top and bottom removable gland plates with knockouts, 4 way,Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge 154 S&F 240V, 10 KA "B" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. 155 S&F in repairs MCB SPN 32 Amps,"C" series 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed.(Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating) 156 S&F 63 Amp MCCB 4 pole, 3 phase, 415 volt of capacityAmp, 16 KA complete with proper copper thimbles, copper reducer etc complete all as specified and directed. 157 S&F 100 Amp MCCB 4 pole, 3 phase, 415 volt of capacityAmp, 16 KA complete with proper copper thimbles, copper reducer etc complete all as specified and directed. 158 M&L for earthing complete with Galvanised steel earth plate electrode 600x600x6 mmmm buried directly in ground (Earthpit not less than2.25m below ground level) with top edge of theplate not less than 1.5m below normal groundlevel, connected to GI wire 4 mmasearth lead by means of bolt, nuts, check nutsandwashers of galvanised iron or steel, upto 7.5mlength, earth strip protected by andincluding 40 mm diaGI pipe (light grade) andconnected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC(1:3:6)type C1 , Precast RCC(1:2:4)TypeB1 coverslab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100mm C/C bothwayswith onehandle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm boreGI Pipe (Medium Grade) for watering, Charcoal andsalt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any typeof soil anddisposal of spoil to a distance n.exc50 m andnecessary testing complete all asshown in Electrical Plate No 3 of SSRPart-I.NOTE : 1. The unit rare includes for protectionh GI pipe of 40mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire of 32x6mm including protection pipe,from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI strip and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate 159 Supply, Laying,testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 4 core 25 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,includingBrass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc complete all as specified and directed. 160 Supply, Laying,testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 2 core 10 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,includingBrass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc complete all as specified and directed. 161 Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier holeetc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soilNote : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding. 162 Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed. 163 Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed. 164 Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cableincludingspreading and punning down to 18 cm thickness complete all as specified and as directed.(Compacted thickness shall be measured) 165 Supply and lay in trench fly ashbricks locally availableof size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed. 166 Supplying and fixingGalvanised mild steel pipe /tubing, light grade complete with all fittings of 40 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed. 167 S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythene ball screwed for irom pipe 25 mm bore dia with fly nut complete all as directed byby Engr-in-Charge 168 S&F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20/25mm bore dia iron pipe, provision of 20 mm /25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed. 169 Supply & Lay pipe galvanized, "Medium class" 25mm(1") dia old or new postion including fittings all as specified & as directedincluding taking down old unseviceable pipe complete all as specified and directed. 170 M&L for screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector ) of size 25mm complete all as specified and directed. 171 S&F 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.
|
