|
Supplying And Installation Of Furniture For Mahatma Gandhi State Institute Of Public Regional Center Building Near Divisional Commissioer Office Distt. Jalandhar , Ground Floor Conference Supply Installation Of Round Discussion Tablesize – 1500 Mm Dia Table Top Shall Be Made Of 25 Mm Thick Pre-Laminated Board Conforming To As Per Is 14587: 1998, All Exposed Edges Of Pre-Laminated Board To Be Sealed With 2Mm Thick Pvc Edge Banding On The User Side At 200O C To Be Applied With The Help Of Hot Melt Glue Through Fit Edge-Banding Machines. The Edge-Banding Of Exposed Area To Be Done In The Way That There Should Not Be Any Sharp Edge Or Corner Left After Processing, Single Pole 40 Mm Diameter With 1.6 Mm Thickness With Heavy Duty Powder Coated (Dft 40-60 Micron) Plain Base. The Height Of Worktop Shall Be 750 Mm From Ground Level. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal / Asis). , Mid Back Chair Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 40 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 45 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 1 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Nylon Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Reception Sofa Supply And Installation Of Two Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre: Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood (Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly: It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 1400Mm (D) 740Mm(H) 740 Mm Seat (H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. , Supply And Installation Of Three Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre : Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood ( Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly : It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 1900Mm (D) 740Mm(H) 740 Mmseat ±10 (Mm):(H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. , Supply And Installation Of Wooden Center Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 1200Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), .. As Approved By Engineer In-Charge/Employer , Supply And Installation Of Wooden Side Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 600Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), .. As Approved By Engineer In-Charge/Employer , Dinining Table With Chairs Supply And Installation Of 6 Seater Dining Table With Chairssize Shall Be 1500Mm Width X900mmdepth X 750Mm Height. Top Shall Be 19 Mm Thick Base Material Shall Be 18 Mm Board. The Understructure Shall Be Having Bend Pipe Structure Of Ms Powder Coated . Pipe Dia 25 Mm ,Dining Table As Approved By Engineer In-Charge/Employer. Dining Table As Approved By Engineer In-Charge/Employer. , First Floor Lecture Hall Supply Installation Of Lecture Tablesize – 1500 Mm X 750 X750 Mm Table Top Shall Be Made Of 25 Mm Thick Pre-Laminated Board , Modesty Penal 18 Mm Thickand Gable End 25 Mm Thick Pre-Laminated Board Conforming To As Per Is 14587: 1998, All Exposed Edges Of Pre-Laminated Board To Be Sealed With 2Mm Thick Pvc Edge Banding On The User Side And 0.8Mm Thick Pvc Edge Banding Tape Pressed On Top And Bottom Side At 200O C To Be Applied With The Help Of Hot Melt Glue Through Fit Edge-Banding Machines. The Edge-Banding Of Exposed Area To Be Done In The Way That There Should Not Be Any Sharp Edge Or Corner Left After Processing, Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal / Asis) Mobile Pedestal Drawer Unit: Each Table Should Be Provided With 3 Drawer Wooden Mobile Pedestal Having Of 2 Sliding Drawer And 1File Box Mounted On 4 Castors With Front 2 Castors Lockable. The Drawer Top, And The Drawer Fascias Is Made Out Of 18Mm Thick Pre-Laminated Board As Per Is 14587(1998), The Back Of The Drawer Unit Is Made From 9Mm Thick Pre-Laminated Board As Per Is 14587(1998). The Units Are Assembled By Knockdown Fittings Such As Mini Fix & Dowels. The Drawer Are Mounted On Rollers Slides To Enable Smooth Operation Of The Drawer. The Pedestals Shall Have Central Locking Mechanism. D/C Type Slim Handle For Drawer And Shutter. Size Of Lockable Castors For Pedestal Storage Unit ± 2 Mm: Diameter 40 Mm And Height 55 Mm, Mobile Pedestal Size Shall Be 400Mm W X 550Mm D X 585Mm H, All Hardware (Handles, Slides ,Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalent. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Lecture Room Training Chair Supply And Installation Of Training Chair The Seat Shall Be Made Up Of 12 Mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly.. The Mid Back Slze Shall Be 400Mm + 5M. (W) X 400 Mm + _5M (H). The Seat Slze Shall Be 450 Mm + 5Mm (W) X 450 Mm + _5M (D). The Polyurethane Foam For Seat Shall Be Moulded With Density = 28 Kglm3 And (+ 2) Hardness =20K2 (+ 2) Without Armrest. The Leg Frame Welded Assembly Made From 25 Dia 16Bg (1.6Thk) Elliptical M.S Erw Tube With Base Plate. , Class Room Table Supply Installation Of Lecture Tablesize – 1200 Mm X 600 X750 Mm Table Top Shall Be Made Of 25 Mm Thick Pre-Laminated Board , Modesty Penal 18 Mm Thickand Gable End 25 Mm Thick Pre-Laminated Board Conforming To As Per Is 14587: 1998, All Exposed Edges Of Pre-Laminated Board To Be Sealed With 2Mm Thick Pvc Edge Banding On The User Side And 0.8Mm Thick Pvc Edge Banding Tape Pressed On Top And Bottom Side At 200O C To Be Applied With The Help Of Hot Melt Glue Through Fit Edge-Banding Machines. The Edge-Banding Of Exposed Area To Be Done In The Way That There Should Not Be Any Sharp Edge Or Corner Left After Processing, Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal / Asis) Mobile Pedestal Drawer Unit: Each Table Should Be Provided With 3 Drawer Wooden Mobile Pedestal Having Of 2 Sliding Drawer And 1File Box Mounted On 4 Castors With Front 2 Castors Lockable. The Drawer Top, And The Drawer Fascias Is Made Out Of 18Mm Thick Pre-Laminated Board As Per Is 14587(1998), The Back Of The Drawer Unit Is Made From 9Mm Thick Pre-Laminated Board As Per Is 14587(1998). The Units Are Assembled By Knockdown Fittings Such As Mini Fix & Dowels. The Drawer Are Mounted On Rollers Slides To Enable Smooth Operation Of The Drawer. The Pedestals Shall Have Central Locking Mechanism. D/C Type Slim Handle For Drawer And Shutter. Size Of Lockable Castors For Pedestal Storage Unit ± 2 Mm: Diameter 40 Mm And Height 55 Mm, Mobile Pedestal Size Shall Be 400Mm W X 550Mm D X 585Mm H, All Hardware (Handles, Slides ,Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalent. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Class Room Chair Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 40 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 45 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 1 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Nylon Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Thumb Pin Board Size – 900X1200mm Fabric Pinup Board , Clerical Room Suptt. Office Table Set Size -1500X750x750mm Table Top Made Of 25 Mm Thick Prelam Particle Board With Pvc Edge Bending,18 Mm Thick Modesty Penal & 25 Mm Thick Gable End With Side Cabinet , Clerical Workstation Supply Installation Of Linier Workstation Size 1200Mmwx600mmd X1200-H Providing And Placing Of Modular Partitions System Coated Aluminum Trims. Panels Construction - Each Panel Consists Of Vertical Extrusions 2Nos And Horizontal Extrusions Made Of 1.2Mm Thick Aluminum With Duly Powder Coated At Every Division Of Tile/Block. Each Panel Have Bottom Frame Fabricated For 45Mm Panelthe Complete Bottom Frame Shall Be Powder Coated With An Average Of 50-60 Microns Thickness Of Powder Coating. The Bottom Frame Is Bolted With The Upright Verticals. Each Panel Consists Of 2Nos Intermediate Blocks. Each Panel Consists A Bottom Tile. These Bottom Tiles Shall Be Press Fitted On To The Assembly Frame Of The Panel. All Partitions And Side Panels Have Leveling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. Tile Finishes : A Fabric Tiles: Fabric Tiles Shall Be Fabric Upholstered .The Fabrics Shall Be Upholstered With Adhesives. • White Board Tiles : White Board Tiles Shall Be Made Of 8.0 Mm Thick Prelam Board As Per Is 12406 Laminated With 0.6Mm Thick High Pressure Laminate On Outer Side & 0.6Mm Backing Laminate On Inner Surface And Will Be Having All Its Edges With Minimum 0.5 Mm Thick Pvc Edging. Aluminum Trims : The Top Trims And End Trims For 45Mm Shall Be Made From Aluminum Extrusion. All Kinds Of Extrusions For 45 Mm Shall Have Average Wall Thickness Of 1.2 Mm & Having Finish Of Powder Coating. Top Trim In 45Mm Thick Panel Shall Be Press Fitted On The Horizontal Extrusion, It Shall Be Slide Fitted With The Help Of Top Trim Connector Made From Pp Copolymer 3530 Grade. End Trim For 45Mm Thick Panel.Wire Management - Wires Shall Be Taken Into The System Through Cable Ducts From The Junction Boxes And It Is Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Wires Runs Through The System From Bottom Tile And Extended To The Top At Various Locations By The Help Of 2 Nos. Vertical Cable Ducts In Each Panels. Cable Duct Shall Be Made From 0.8 Mm Thick Aluminum. It Is Constructed With Two Parts, One Is Body & Another Is Cover. It Holds The Cables & Gives Aesthetic Appearance By Covering All Cables Entry, Which Are Moving Upward To The Panels. Partitions To Be Provided As Per The Site And Layout Approval. Mobile Pedestal Drawer Unit: Each Table Should Be Provided With 3 Drawer Wooden Mobile Pedestal Having Of 2 Sliding Drawer And 1File Box Mounted On 4 Castors With Front 2 Castors Lockable. The Drawer Top, And The Drawer Fascias Is Made Out Of 18Mm Thick Pre-Laminated Board As Per Is 14587(1998), The Back Of The Drawer Unit Is Made From 9Mm Thick Pre-Laminated Board As Per Is 14587(1998). The Units Are Assembled By Knockdown Fittings Such As Mini Fix & Dowels. The Drawer Are Mounted On Rollers Slides To Enable Smooth Operation Of The Drawer. The Pedestals Shall Have Central Locking Mechanism. D/C Type Slim Handle For Drawer. All Hardware (Handles, Slides ,Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalent. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Chair Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 42 Cm (+ 3Cm) Width, 42 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 42 Cm (+ 2Cm) Max Width, 42 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 45 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 1 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Nylon Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Regional Director Room Regional Director Office Table Size – 2100X900x750 With Side Cabinet And Drawer Unittable Top Made Of 36 Mm Thick Prelam Particle Board With Pvc Edge Bending,18 Mm Thick Modesty Penal & 36 Mm Thick Gable End , Executive High Back Chair With Arms, Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 500 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 500 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest . The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 3 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Aluminum Dia Cast Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Medium Back Visitor Chair With Arms, Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 500 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 500 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest . The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 3 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Aluminum Dia Cast Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Sofa Supply And Installation Of Three Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre : Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood ( Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly : It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 1900Mm (D) 740Mm(H) 740 Mmseat ±10 (Mm):(H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. , Center Table Supply And Installation Of Wooden Center Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 1200Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), .. As Approved By Engineer In-Charge/Employer , Side Table Supply And Installation Of Wooden Side Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 600Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), . As Approved By Engineer In-Charge/Employer , Faculty Office, Study Table Supply Installation Of Study Table With Key Board Tray, One Storage Shelf, One Pencil Drawer And One Cpu Storage, Table Top: Size 1200Mmx600mmx750mm, Table Top And Side Panel And Middle Panel Shall Be Made Of 25 Mm Thick Pre-Laminated Board Conforming To As Per Is 14587: 1998, Grade Ii Corresponding To Is 12406:2003, With E1 Grade Laminate All Hardware (Handles, Slides, Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalents. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Study Chair Supply And Installation Of Study Chair The Seat Shall Be Made Up Of 12 Mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Back Is Made Up 12 Mm Thick Hot Pressed Plywood Upholstered With Replaceable Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Ply And Foam Shall Be Designed With Contoured Lumber Support For Comfortable Seating Posture. The Mid Back Slze Shall Be 4 60Mm + 5M. (W) X 460 Mm + _5M (H). The Seat Slze Shall Be 460 Mm + 5Mm (W) X 460 Mm + _5M (D). The Polyurethane Foam For Seat And Back Shall Be Moulded With Density = 45 Kglm3 And (+ 2) Hardness =20K2 (+ 2).The Armrest Top Shall Be Made Of Moulded Polyurethane (P.U). The Backrest Shall Consists Of A Fixed Type Mechanism I.E. No Back Up I Down Adjustment. The Leg Frame Welded Assembly Made From 25 Dia 16Bg (1.6Thk) Elliptical M.S Erw Tube With Base Plate , Supply And Installation Of Three Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre : Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood ( Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly : It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 1900Mm (D) 740Mm(H) 740 Mmseat ±10 (Mm):(H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. , Supply And Installation Of Wooden Center Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 1200Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), .. As Approved By Engineer In-Charge/Employer , Supply And Installation Of Wooden Side Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 600Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), . As Approved By Engineer In-Charge/Employer , Computer Lab Workstation . Staff Modular Workstation 45 Mm Thick Partition, Above The Worktop Fabric Pinup Board & Table Top 25 Mm Thick, Gable End 25 Mm Thick Prelam Board. Supply Installation Of Back To Back Workstation Size 1200Mmwx600mmd X1200-H Providing And Placing Of Modular Partitions System Coated Aluminum Trims. Panels Construction - Each Panel Consists Of Vertical Extrusions 2Nos And Horizontal Extrusions Made Of 1.2Mm Thick Aluminum With Duly Powder Coated At Every Division Of Tile/Block. Each Panel Have Bottom Frame Fabricated For 45Mm Panelthe Complete Bottom Frame Shall Be Powder Coated With An Average Of 50-60 Microns Thickness Of Powder Coating. The Bottom Frame Is Bolted With The Upright Verticals. Each Panel Consists Of 2Nos Intermediate Blocks. Each Panel Consists A Bottom Tile. These Bottom Tiles Shall Be Press Fitted On To The Assembly Frame Of The Panel. All Partitions And Side Panels Have Leveling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. Tile Finishes : A Fabric Tiles: Fabric Tiles Shall Be Fabric Upholstered .The Fabrics Shall Be Upholstered With Adhesives. • White Board Tiles : White Board Tiles Shall Be Made Of 8.0 Mm Thick Prelam Board As Per Is 12406 Laminated With 0.6Mm Thick High Pressure Laminate On Outer Side & 0.6Mm Backing Laminate On Inner Surface And Will Be Having All Its Edges With Minimum 0.5 Mm Thick Pvc Edging. Aluminum Trims : The Top Trims And End Trims For 45Mm Shall Be Made From Aluminum Extrusion. All Kinds Of Extrusions For 45 Mm Shall Have Average Wall Thickness Of 1.2 Mm & Having Finish Of Powder Coating. Top Trim In 45Mm Thick Panel Shall Be Press Fitted On The Horizontal Extrusion, It Shall Be Slide Fitted With The Help Of Top Trim Connector Made From Pp Copolymer 3530 Grade. End Trim For 45Mm Thick Panel.Wire Management - Wires Shall Be Taken Into The System Through Cable Ducts From The Junction Boxes And It Is Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Wires Runs Through The System From Bottom Tile And Extended To The Top At Various Locations By The Help Of 2 Nos. Vertical Cable Ducts In Each Panels. Cable Duct Shall Be Made From 0.8 Mm Thick Aluminum. It Is Constructed With Two Parts, One Is Body & Another Is Cover. It Holds The Cables & Gives Aesthetic Appearance By Covering All Cables Entry, Which Are Moving Upward To The Panels. Partitions To Be Provided As Per The Site And Layout Approval. Mobile Pedestal Drawer Unit: Each Table Should Be Provided With 3 Drawer Wooden Mobile Pedestal Having Of 2 Sliding Drawer And 1File Box Mounted On 4 Castors With Front 2 Castors Lockable. The Drawer Top, And The Drawer Fascias Is Made Out Of 18Mm Thick Pre-Laminated Board As Per Is 14587(1998), The Back Of The Drawer Unit Is Made From 9Mm Thick Pre-Laminated Board As Per Is 14587(1998). The Units Are Assembled By Knockdown Fittings Such As Mini Fix & Dowels. The Drawer Are Mounted On Rollers Slides To Enable Smooth Operation Of The Drawer. The Pedestals Shall Have Central Locking Mechanism. D/C Type Slim Handle For Drawer. All Hardware (Handles, Slides ,Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalent. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Computer Lab Chair Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 40 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 45 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 1 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Nylon Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon. , Double Bed Set With Side Table Double Bed With Overall Size 75”Wx85”Lx40”H And With Mattress Size W72”X L78”. The Box All Four Sides And Top Made Of 19Mm Isi Marked Compressed Ply Board Faced With 0.8Mm Thick Laminate On Both Sides Of Approved Shade With Teakwood Beading On The Edges. The Height Of Box Will Be 15” . The Box Having Openable Lid With Full Length Hinges With Center Wooden Support And Holder For Lid And The Bottom Of Bed Made Of 12 Mm Isi Marked Compressed Ply With .8Mm Thick Laminate On One Side. The Bed Having Designer 4” Sloped Head Side Made In Combination Of 8 And 18 Mm Laminated Board With Slope And Supported With 25Mm Thick Vertical Supports At The Back. The Foot Side Made Of Laminated Board With 32Mm Thickness. The Bed Is Provided With 2 Nos. Bed Side Table Made Of 18Mm Thick Medium Density Fiber/Partical Board , All Panels Of Unit Are Inter Connected With Rastex , Dowel And Socketsall The Edges Provided With Machine Pressed 0.8Mm Thick Pvc Edge Bands Glued With Hot Melt Eva Glue. The Side Unit Having Two Drawers Made Of 18Mm Thick Medium Density Fiber/Partical Board , Fitted On Full Length Ball Based Telescopic Channels And 96Mm Ss Handles. The Complete Double Bed Set With Side Table. Double Bed With Overall Size 75”Wx85”Lx40”H And With Mattress Size W72”X L78”. The Box All Four Sides And Top Made Of 19Mm Isi Marked Compressed Ply Board Faced With 0.8Mm Thick Laminate On Both Sides Of Approved Shade With Teakwood Beading On The Edges. The Height Of Box Will Be 15” . The Box Having Openable Lid With Full Length Hinges With Center Wooden Support And Holder For Lid And The Bottom Of Bed Made Of 12 Mm Isi Marked Compressed Ply With .8Mm Thick Laminate On One Side. The Bed Having Designer 4” Sloped Head Side Made In Combination Of 8 And 18 Mm Laminated Board With Slope And Supported With 25Mm Thick Vertical Supports At The Back. The Foot Side Made Of Laminated Board With 32Mm Thickness. The Bed Is Provided With 2 Nos. Bed Side Table Made Of 18Mm Thick Medium Density Fiber/Partical Board , All Panels Of Unit Are Inter Connected With Rastex , Dowel And Socketsall The Edges Provided With Machine Pressed 0.8Mm Thick Pvc Edge Bands Glued With Hot Melt Eva Glue. The Side Unit Having Two Drawers Made Of 18Mm Thick Medium Density Fiber/Partical Board , Fitted On Full Length Ball Based Telescopic Channels And 96Mm Ss Handles. The Complete Bed With Side Tables 15 Duly Polished In Walnut Melamine Finish , Wooden Study Table Size – 900X600x750mm , Peacock Chair Easy Knockdown Chair Is Fixed By 12 Screws Easy To Assemble, Ply-Bent, Joint Less, Rigid Veneer Lumber Frame Ensure Stability And Durability, Water Fall Seat With High Quality Seat/Back. , Study Table Chair Peacock Easy Chair - Chair With Seat, Seat Size 450X500mm And Having Teakwood Designer Arms And Frame Made Teak In Combination Of 1.1/2” Sq. , 1” Sq. And Having 32 Density 50Mm Cushions On Seat & Back Fitted On 12 Mm Thick Steam Press Molded Ply Having Special Contours For Extra Comfort , Duly Upholstered With Best Quality Green Color Upholstery Cloth. The Chair Legs Are Provided With Heavy Duty Pvc Buffers. The Complete Frame Painted And Polished In Walnut Wooden Shade , Two Seater Sofa Supply And Installation Of Two Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre: Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood (Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly: It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 1400Mm (D) 740Mm(H) 740 Mm Seat (H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. - , One Seater Sofa Supply And Installation Of One Seater Sofa • Seat Foam : The Seat Is Made Offoam With Density 28± 2 Kg/Cu. Mtr Having Upholstered With Fabric Or Leatherette. Seat Cushion Thickness ±3 (Mm): 100Mm • 2) Back Foam: The Back Is Made Offoam With Density 28 ± 2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette . Backrest Cushion Thickness ±3 (Mm): 75Mm • 3) Understructre: Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood (Moisture Resistance & Termite Proof As Per Is: 303) & • 4) Leg Assembly: It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) /Chrome Plated Tube & Plate With Plastic End Cap. (W) 850Mm (D) 740Mm(H) 740 Mm Seat (H) 400 Mm, Sofa Leg Height ±2(Mm): 100 Mm, Sofa Leg Width / Diameter ±2 (Mm): 30 Mm, Sofa: As Approved By Engineer In Charge/Employer. , Center Table Supply And Installation Of Wooden Side Table With 6 Mm Glass Top, Under Structure Of Wooden Shelf Is Made Of 25 Mm Teak Wood, , Size: 600Mm(L) X Width :600Mm (W) X Height:450 Mm (±10% )Engineering Variation In Dimension), . As Approved By Engineer In-Charge/Employer , Wooden Almirah With Locking Glass Providing & Fixing At Wooden Almirah With Locking Glass Cabinet 20” Deep To Be Made Up Of 19.0 Mm Bwp Block Board With Finished With 0.8Mm Thick White Laminated Finish. The Front Shutter Shall Be Of 17.0 Mm Thick Finished With 1.0 Mm. Laminated Finish . The Cubbopard To Be Made All Enclosed With Rear 8.0Mm Ply Again Finished With 0.8Mm Laminated Finish From Inside .The Cubboard Shall Have Teak Wood Beading On All Edges Of Block Boardbrush Finished 150Mm Handels, The Inside Portion Shall Have With Horizontal & Vertical Shelves As Per The Given Design With Magnetic Catchers .The Cost Shall Include All Materials,Locks, Catchers, All Labour Etc Complete. (Note- Make- Archid, Century, Green Ply & Duro.) , Wooden Table For Suit Case , T.V Cabinet Providing And Fixing At Site Tv Cabinet Of Approved Design & Drawings To Be Made Up Of 18.0Mm Bwp Ply, And Finished With Approved Shade Of Laminated Finish, Including All Accessories, Space For Fixing Of Tv, Necessary Shelves, All Accessories Etc Complete (Note- Ply Make- Archid, Century, Green Ply & Duro.) , Dias Table As Approved By Engineer-In-Charge/Employer , Dias Chair As Approved By Engineer-In-Charge/Employer , Wooden Podium Wooden Podium With 3 Shelves And Titled Top. Size: 1250Mm(H)X550mm(W)X550mm(D) Made Up Of Block Board With Pvc Edge Banding On All Sides. Laminated Sunmica Of 1Mm Duly Pasted On All Exposed Sides , Faculty Table Table Top Made Of 25 Mm Thick Prelam Particle Board With Pvc Edge Bending,18 Mm Thick Modesty Penal & 25 Mm Thick Gable End With Side Cabinet. Supply Installation Of Office Tablesize – 1500 Mm X 750 X750 Mm Table Top Shall Be Made Of 25 Mm Thick Pre-Laminated Board , Modesty Penal 18 Mm Thickand Gable End 25 Mm Thick Pre-Laminated Board Conforming To As Per Is 14587: 1998, All Exposed Edges Of Pre-Laminated Board To Be Sealed With 2Mm Thick Pvc Edge Banding On The User Side And 0.8Mm Thick Pvc Edge Banding Tape Pressed On Top And Bottom Side At 200O C To Be Applied With The Help Of Hot Melt Glue Through Fit Edge-Banding Machines. The Edge-Banding Of Exposed Area To Be Done In The Way That There Should Not Be Any Sharp Edge Or Corner Left After Processing, Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal / Asis) Mobile Pedestal Drawer Unit: Each Table Should Be Provided With 3 Drawer Wooden Mobile Pedestal Having Of 2 Sliding Drawer And 1File Box Mounted On 4 Castors With Front 2 Castors Lockable. The Drawer Top, And The Drawer Fascias Is Made Out Of 18Mm Thick Pre-Laminated Board As Per Is 14587(1998), The Back Of The Drawer Unit Is Made From 9Mm Thick Pre-Laminated Board As Per Is 14587(1998). The Units Are Assembled By Knockdown Fittings Such As Mini Fix & Dowels. The Drawer Are Mounted On Rollers Slides To Enable Smooth Operation Of The Drawer. The Pedestals Shall Have Central Locking Mechanism. D/C Type Slim Handle For Drawer And Shutter. Size Of Lockable Castors For Pedestal Storage Unit ± 2 Mm: Diameter 40 Mm And Height 55 Mm, Mobile Pedestal Size Shall Be 400Mm W X 550Mm D X 585Mm H, Side Cabinet, Size Of Cabinet: Width Of Unit: 900 Mm (± 10Mm), Height Of Cabinet 750 Mm (±10 Mm), Depth Of Cabinet: 400Mm (±20Mm), Material Of Cabinet: Flat Single Layer Pre-Laminated Board Conforming To Designation Pl-203 Of Is 14587/Latest Having Balancing Laminated Of 1.0 Mm Thick On Both Side And E1 Grade Pre-Laminated Board.All Hardware (Handles, Slides, Hinges, Locks, Sliding Channel, Screw Etc) Hettich/Ebco/Or Equivalent. Pre Laminated Board And Laminate Make: (Century/Action Tesa/Merino/Greenlam/Green Penal /Asis).Lecture Table As Approved By Engineer In-Charge/Employer , Faculty Chair Seat/Back Assembly: The Seat Is Made Up Of Insert Moulded Polyurethane Foam Upholstered With Foam Laminated Mesh Fabric. The Insert Moulded Foam Is Assembled Over A Load Bearing Plastic Seat Cover. The Back Is Made Up Of One Piece Injection Moulded Frame. The Inner Frame Is Upholstered With Mesh Fabric And Mounted On The Main Assembly. The Back Has Lumbar Support For Achieving Comfortable Seating Posture. Sub Assembly Seat Size = 45 Cm (+ 3Cm) Width, 45 Cm (+ 2Cm) Depth. Sub Assembly Back Size= 40 Cm (+ 2Cm) Max Width, 40 Cm Ht (+ 3Cm). Effective Back Ht From Seat = 45 Cm (+ 3Cm) 2) Polyurethane Foam: The Polyurethane Foam For Seat Is Moulded With Density = 40 ±4 Kg/M3 And Hardness = 34 ± 4. 3) Armrests (Adjustable) : The Armrest Top Is Injection Moulded In Polyurethane And Mounted On The Injection Moulded Height Adjustable Type Armrest. The Armrest Height Is Adjustable Up To 4-5Cms In 3 Steps Adjustable. Front Pivot Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360 Degrees Revolving Type - Single Point Control - Front Pivot For Tilt With Feet Resting On Ground Ensuring More Comfort - Tilt Tension Adjustment – 1 Position Locking With Anti-Shock Featurepneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Of 8.5 (+ 1Cm) Cm.Pedestal Assembly: Pedestal Is Made Of Nylon Fitted With 5 Nos. Twin Wheel Castors (Castor Wheel Dia. 6.0 + 2Cm). The Pedestal Is 65.0Cm + 3Cm. Pitch Center Dia. (65.0 Cm + 3Cm With Castors). Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Nylon
|
