|
Tender For Special Repair To Certain Omqs/ Smqs At Af Station Palam Under Ge (Af) Palam, Delhi Cantt-10; 1 Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge. 2 Demolition of PCC of any description and in any position not otherwise specifically Provided for complete all as specified and directed by Engineer-in-Charge. 3 Dismantling floor hearth or wall tiling including cement mortar bedding and removing debries off the premises complete all as specified and directed by Engineer-in-Charge. 4 Demolition of reinforced cement concrete(reinforcement cut as required to facilitate demolition) for landing, cooking platform and chajjas complete all as specified and directed by Engineer-in-Charge. 5 Takingdowncementplasteron brick or concretewall surfaces etcincluding rakingoutjoints, hacking for key , scrubbing down withwateretc complete all as specified and directed by Engineer-in-Charge. 6 Demolition of brick work or stone/ boulder masonrybuilt in cement mortar of any description complete all as specified and directed by Engineer-in-Charge. 7 Demolition of stone slab and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed by Engineer-in-Charge. 8 M&L for Brick work with sub class "B" bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. 9 M&L for 15 mm thick cementplaster on fair faces of brick work or concrete surfaces in cement mortar 1:6, to befinishedeven and smooth without usingextra cement complete all as specified and directed by Engineer-in-Charge. 10 M&L for 15 mm thick cementplaster on fair faces of brick work or concrete surfaces in cement mortar 1:4, to befinishedeven and fairwith water proofing compound by weight as per manufacturer"s instructions. (WPC will be paid separately).including necessaryscaffoldingup to (G+3 storey) complete all as specified and directed by Engineer-in-Charge. 11 M&Lfor 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar 1:3 in ceilings, to befinishedeven and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. 12 M&L for cement concrete 1: 2 :4type B-O (using 12.5mm graded stone aggregate), 25mm thick in sub base, floorsetc complete all as specified and directed by Engineer-in-Charge. 13 M&L Glazed ceramic coloured tiles in vertical surface 450x 350x 7mm/ 450x 300x 7mm /350x250x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10 mm thick renderingCM 1: 4 as on vertical surfaces such as skirting, dados, etc complete all as specified and directed by Engineer-in-Charge. 14 M&L for Non- skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. 15 M&L for non-skid colouredceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm butnexc 0.18 Sqm in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match completeincluding 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. 16 M&Lfornon-skid colouredceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm butnexc 0.18 Sqm as in skirtingetc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete 10 mm thick rendering CM 1: 4 as on vertical surfaces complete all as specified and directed by Engineer-in-Charge. 17 M&L for vitrified tiles, light shade,8 to 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. 18 All as per item no 17 above but in vertical surface of wall, skirting and including 10 mm thick rendering of CM 1: 4 as on vertical surfaces such as skirting, dados, etc complete all as specified and directed by Engineer-in-Charge. 19 M&L for 18 to20mm thick Granite (of jet black ) work (table rubbed and polished ) in steps ,jambs ,pillars,window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge. (Exposed edges to make half round) 20 M & L for Cement concrete 1:3:6 type C2 using 20mm graded stone aggregate in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen85/25and sand inthe proportion of (1:3 ) by weight complete all as specified and directed by Engineer-in-Charge. 21 M & L for machine cut Kota stone slab20 to 25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete and including 20 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge. 22 M & L for machine cut Kota stone slab20 to 25 mm thick in steps, skirting, dado and Pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing completeand including 15mm thick renderingCM 1:4 complete all as specified and directed by Engineer-in-Charge. 23 M&L for form work to side and soffits of shelves or cooking platformfor rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge. 24 M&L for Reinforced cement concrete 1:2:4 type B1 using ( 20mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings balconies, cooking platform, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge. 25 M&L for Reinforced cement concrete 1:2:4 type B1 ( 20mm graded aggregate)as in fascia, louveres, parapets, railing and chajjas and the like complete all as specified and directed by Engineer-in-Charge. 26 Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. 27 Taking down Chowkats or frames with shutters not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge. 28 Taking down Chowkats or frames with shutters exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge. 29 Taking down shutter of any description exc 1 Sqm but notexc 2 Sqm each complete all as specified and directed by Engineer-in-Charge. 30 M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge. 31 S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stliles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed by Engineer-in-Charge. 32 M&Lforpressedsteelframe fordoorwithonerebatedofsize 105x 60 mmincludingnecessaryfixing lugs, hinges , lockstrikeplate etc complete all as specified and directed by Engineer-in-Charge. 33 M&Lforpressedsteelframe fordoorwithdouble rebatedofsize125 x 60 mm includingnecessaryfixing lugs, hinges , lockstrikeplateetccomplete all as specified and directed by Engineer-in-Charge. 34 M&L for cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in back filing to pressed steel frames etc complete all as specified and directed by Engineer-in-Charge. 35 S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-Charge. 36 S&F for 35 mm thick 2nd class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, provided with stiles and rails as specified in SSR Part-I Section-8 clause 8.24 (a) fixed to chowkats complete all as specified and directed by Engineer-in-Charge. 37 S&F of steel window box type made of ERW hollow section of size 130mmX65mm X 1.25mm thick doule rebate comprises gauged and glazed skeleton shutter ERW Section 50mmx20mm x 1mm thick, double shutter with leaf and arrangements for cooler openingincluding iron grill bar with 12mm square complete welded to frame with vertical mullion of size 130mmx65mm with 1.25mm thick ERW box type including holes cutting for hold fast (04 Nos each window) and making good dismantled portion with PCC (1:2:4) type B-1 including following fittings welded to frame / shutter :- (a) Hold fast of 150mm long of flat iron 25mmx3mm made to shape-04 Nos each window. (b) MS Handle cold rolled of size 100mm long - 01 No per leaf (c) MS Tower bolt 100mm long- 02No per leaf(d) Z-section 20mmx25mm long stopper - 01No per leaf. (e) MS pintle hinges of size 40mmx25mm -2 Nos per leaf including one coat of red oxide shop primer complete all as specified and directed by Engineer-in-Charge.(Note : Wire mesh, sheet glass, painting etc shall be measured & paid separately under appropriate items). 38 S&F for MS butt hinges 100mm size, cold rolled, medium weightfixed with screws to wooden frames or welding to steelframes etc complete all as specified and directed by Engineer-in-Charge. 39 S&F Butt hinges, 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed by Engineer-in-Charge. 40 S&F Aluminium anodised, barrel tower bolts of extruded section and fixed 150mm complete all as specified and directed by Engineer-in-Charge. 41 S&F Aluminium anodised, barrel tower bolts of extruded section and fixed 200mm complete all as specified and directed by Engineer-in-Charge. 42 S&F forextruded aluminium alloy handles, fabricated type, anodised, 125 mm size complete all as specified and directed by Engineer-in-Charge. 43 S&F in repairMS powdercoated20 mm diacurtain rodincludingbracketsandendknobs / finials complete all as specified and directed by Engineer-in-Charge. 44 S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed withscrews complete all as specified and directed by Engineer-in-Charge. 45 S&F 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered ,put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge. 46 Dismantlingboarding anysize or description, fixed in any position or in any thickness, including cover fillets with nails complete all as specified and directed by Engineer-in-Charge. 47 S & F 19mm thickprelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws as in cup boards, shelves andpelmet boxes etc any description fixed with screws complete all as specified and directed by Engineer-in-Charge. 48 S&Fin repair factory made 18 mm (+0.7 mm ) thick celuka PVC ply of density 600 kg/cbm manufactured by an ISO 900-2008 certified company . One side prelam and other side plain 18 mm thick celuka PVC Ply for kitchen cabinet/ cupboard shutter complete all as specified and directed by Engineer-in-Charge. 49 S&Fin repair factory made 18 mm (+0.7 mm ) thick celuka PVC ply of density 600 kg/cbm manufactured by an ISO 900-2008 certified company .plain 18 mm thick celuka PVC Ply for shelves/partitions/drawers complete all as specified and directed by Engineer-in-Charge. 50 S&F 100mm aluminium anodised Hasp and staple, safety type,including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer-in-Charge. 51 S&F 40mm dia, cupboard/cabinet knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by Engineer-in-Charge. 52 S&F 100 mm size Stainless Steelhandle complete all as specified and directed by Engineer-in-Charge. 53 S&F 50 mm Magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed by Engineer-in-Charge. 54 S&F 40 mm size (width of flap when open) stainless steel piano hinges complete all as specified and directed by Engineer-in-Charge. 55 S&F stainless steel telescope channel of size 500mm complete all as specified and directed by Engineer-in-Charge. 56 S&F stainless steel thali basket fo size 550 x 600x 200mm Grade -304 complete all as specified and directed by Engineer-in-Charge. 57 S&F stainless steelbasket of size 550 x 600x 200mm Grade -304 complete all as specified and directed by Engineer-in-Charge. 58 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge. 59 S&F forsheet glass4mm thick qualityfixing to steel/aluminiumwindow shutters in any position with new beads/ steel section as required for securing complete all as specified and directed by Engineer-in-Charge. 60 S&F for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apertupre 1.40mm and fixedwith tinned tacks or galvanised wire staples complete all as specified and directed by Engineer-in-Charge. 61 S&F for Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. 62 S & F of power coated aluminium window and ventilator shutters with side hungs, aluminium section weighing 0.55 kg/m including necessary joining cleats,gauge/ glazing cips rubber packing anodised aluminium snap beading screws anodised aluminium fittings complete all as specified and directed by Engineer-in-Charge. 63 S&F aluminium powder coated three track sliding window with mosquito net two track for glass leaf sliding and one track for mesh leaf sliding outer frame weighing 0.699 Kg/m,75x26 mm size equivalent Jindal model 20671, shutter plain of size 37.5x15mm weighing 0.366 Kg/m, Section No 20690 Jindal), with powder coating of min thickness 50 micron with one or more rebates, sliding type without sash bars, 5mm thickness double tampered clear glass , rubber packing, snap beading screws,with horizontal sliding type with stainless steelmesh,frame,powder coated aluminium grill type AL 925 or equivalent grill, cutting in suitable size and fitting with screws and suitable beadings to aluminum window frame complete all as specified and directed by Engineer-in-Charge. 64 S&F 5.50mm thick tinted ,sheet glass of selected qualityfixed to aluminium/steelframe work complete all as specified and directed by Engineer-in-Charge. 65 S & F in repair floor door stopper of size 140 mm long aluminium body and tongue, anodized with hard drawn steel spring including cleats etc fixed to door complete all as specified and directed by Engineer-in-Charge. 66 M&L for preparing New plastered surfaces andapplying two coats of distemper oil emulsion on wall surfaces including primer complete all as specified and directed by Engineer-in-Charge. 67 M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white washcomplete all as specified and directed by Engineer-in-Charge. 68 M&L forpreparation of newplastered surfaces of ceiling surface and applyingtwocoat of oil bounddistemper including primer complete all as specified and directed by Engineer-in-Charge. 69 M& L for preparation of new plastersurface of walls ,chajjas, soffits & beamincluding necessary scaffolding and applying two coats of cement base paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. 70 M&L for preparation of newly plastered surfaces of walls and applyingtwocoatsofexterior emulsion paint over one coat of primer over 2mm thick (avg thickness) wall care putty complete all as specified and directed by Engineer-in-Charge. 71 M&Lfor complete removalofexisting treatmentof old decorated external surface of walls by electrically operated grinder including necessary scaffolding complete and applyingtwocoatsofexterior emulsion paint over a coat of primer of same brand over 2mm thick (avg thickness) wall care putty to obtain even and smooth surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge. 72 M&L for complete removal of existing treatment of old plasteredsurfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats ofdistemper oil emulsion over one coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge. 73 M& L forcomplete removal of existing treatment of oldplastersurface of walls ,chajjas, soffits & beamincluding necessary scaffolding and applying two coats of cement base paint complete all as specified and directed by Engineer-in-Charge. 74 M&L for preparing oldsurfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge. 75 Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. 76 M&Lfor preparation of old painted surfacesofwood& wood based surfaces ofanydescriptionnot otherwisedescribedover10 cmwidth&girthand applying onecoatof syntheticenamel paint complete all as specified and directed by Engineer-in-Charge. 77 M & L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description over 10cm width including preparation complete all as specified and directed by Engineer-in-Charge. 78 M&Lforpreparationofoldpaintedsurfacesofsteelandiron surfacesofany descriptionnototherwise described over10cm width&girth and applying onecoatof synthetic enamelpaint complete all as specified and directed by Engineer-in-Charge. 79 M&L for applying 2mm (average ) thickness putty on old/ new wall and ceilingplastered surfaces, even and smooth surface complete all as specified and directed by Engineer-in-Charge. 80 Dismantling of Brick tiles Single layer on roofs laid dry or with cement mortar complete all as specified and directed by Engineer-in-Charge. 81 Demolition of mud in roofs, any thickness including plastering & leeping (whether full or part)removal of debris at a distance exc 250m but not exc 500m and depositing where directed complete all as specified and directed by Engineer-in-Charge. 82 M & L Cement concrete Type B-1 1:2:4( 20mm graded stone aggregate ) in roof padding complete all as specified and directed by Engineer-in-Charge. 83 M&Lfor15 mmthickrenderingon concrete surface on roof in cementplaster1:4finishedevenand fairwithoutusingextracement, with water proofing compound by weight as per manufacturer"s instructionscomplete all as specified and directed by Engineer-in-Charge. (Note: Water proofing Compound measured and paid separately) 84 Supply only water proofing compoundcomplete all as specified and directed by Engineer-in-Charge. 85 M&LforAPPbasedmodifiedpre fabricatedfivelayer3 mm thick andweighingnotlessthan3.6 Kg/Sqmwater proofing membrane reinforcedwithpolyesternon wovenfabricmatwith160 gm/Sqm blackfinishedwith compatibleprimerconformingto IS 3488 @ 0.30 Lit/ Sqm andbonding material85/25bitumen1.2 Kg/Sqmbeforeandafter layingmembranelaidbytorchapplicationsideoverlapof 75 mm andoverlapof 100 mm longitudinally, At thejunctionof roof andparapet walla groveof 20 x 20mmshall be madeatthehtof100 mmandmembrane shall be inserted andsealedwithbituminousmasticjoints/overlap shallbe sealedwithhotbitumen85/25, Twocoat of water proofing aluminiumpainton topof APPmembrane shallbe appliedcomplete all as specified and directed by Engineer-in-Charge. 86 M&L for guniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in CM 1:4 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement including necessary form work to be carried out complete all as specified and directed by Engineer-in-Charge. Note.- Whereever reinforcement required will be measured and paid separately 87 Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. 88 Taking up or down 20 mm bore steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. 89 S&F Tubes, "medium grade" 15mm bore galvanised steel, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. 90 All as per item No 90 above but 20mm bore complete all as specified and directed by Engineer-in-Charge. 91 S&F in repairs 15 mm bore Bib taps, cast copper alloy, Chromium plated fancy type, long/ short body screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. 92 S&F in repairfor15 mm diastopvalveCP cast copperalloyfancy type screweddownhigh pressurewithcrutch orbutterfly handle screwedbothsidefor ironpipeoefor unionandfixed complete all as specified and directed by Engineer-in-Charge. 93 S&Fin repair15 mm two in one angle valve cast copper alloy, chromium plated with wall flangeand fancy typewithhigh pressure screwed down and with CP flange of same make complete all as specified and directed by Engineer-in-Charge. 94 S&F in repairs vitreous china wash down water closet pan (pedestal pattern), and trap white (excluding flushing cistern and seat cover) including connection to drain (or outgoing pipe) and to fushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-Charge. 95 S&F in repair water closet vitreous china squatting pan,Orissa pattern size 580x440mm white with integral foot rests ( excluding flushing cistern and flush pipe) and includingwith "P" or "S trap complete including" provision of lime concrete bedding fixed in repair complete all as specified and directed by Engineer-in-Charge. 96 S&F in repair PVC flushing cistern of 10 ltrs capacity valveless, syphonic action type,low level, white with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore and connection to pipes etc complete all as specified and directed by Engineer-in-Charge. 97 S&F in repair, 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. 98 S&F in repair, 15mm bore anglecock cast copper alloy, chromium plated screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge. 99 S&F in repair ,SS health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and directed by Engineer-in-Charge. 100 S&F in repair, PVC connections 15mm size with PTMT nuts of length 600 mm and fixed complete all as specified and directed by Engineer-in-Charge. 101 S&F in repair, wash hand basins vitreous china flat back 450mmx300mm size white, first quality, with and including chromium platedwaste coupling 32mm size, PVC waste pipe 25mm bore heavy duty China and plug and porcelain stopper, brackets of Mild Steelangle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer over angle iron brackets complete to walls complete all as specified and directed by Engineer-in-Charge. 102 S&F in repair 600 x450 mm fancy typeor bevelled edge mirror of selected quality glass, mounted on 6mm thick ACbuilding board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge. 103 S&F in repairs sink mixer with swivel spout and 450 mm long braided hoses, brass, chromium plated complete all as specified and directed by Engineer-in-Charge. 104 S&F in repairbasin mixer with popup waste system , Hot and Cold Facilities and 450 mm long braidedhoses, brass, chromium platedcomplete all as specified and directed by Engineer-in -Charge. Make: Model No- DRC-37005 B of make Jaquar or equivalent in Kohler/Hindware. 105 S&F in repairsthree way wall mixer with popup waste system , hot and cold facilities and 450 mm long braided hoses, brass, chromium plated complete all as specified and directed by Engineer-in-Charge. 106 S & F in repair MS, CP paper holder complete all as specified and directed by Engineer-in-Charge. 107 S&F in repair brass, Tubular towel rail, 20mm dia, D type, 60cm long between flangesincluding chromiumplated brass screwand plasticcleats, (minimumweight190gms ) complete all as specified and directed by Engineer-in-Charge 108 S&F inrepair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engineer-in-Charge 109 S&F in repair Brass chromium plated shower rose 125 mm size fixed to 15 mm bore iron pipe complete all as specified and directed by Engineer-in-Charge 110 S&F in repair glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge. 111 S & F in repair corner glass shelf set of 3 Nos with bracket complete all as specified and directed by Engineer-in-Charge. 112 S&F in repairs elegant mirror PVC cabinet colouredwith towel rail of size 422 x 622 mm complete all as specified and directed by Engineer-in-Charge. 113 S & F in repair SS, CP Soap dish complete all as specified and directed by Engineer-in-Charge. 114 S & F in repair SS, CP towel ringcomplete all as specified and directed by Engineer-in-Charge. 115 S & F in repair SS, CP tumbler holder complete all as specified and directed by Engineer-in-Charge. 116 S&Fin repairs, cast iron Nahani trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all asspecified and directed byEngr-in-Charge. 117 Demolitionand breaking up drain pipe 75/100mm dia ( Salt glazed ware, AC or PVC) of any Type complete all as specified and directed by Engineer-in-Charge. 118 S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and directed by Engineer-in-Charge. 119 S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and directed by Engineer-in-Charge. 120 S&F in repairs PVC(SWR) bends any radius, 75 mm bore complete all as specified and directed by Engineer-in-Charge. 121 S&F in repairs PVC(SWR) bends any radius, 110 mm bore complete all as specified and directed by Engineer-in-Charge. 122 Dismantling water tank and removal from site exc 500 ltr and n exc 1000 ltr complete all as specified and directed by Engineer-in-Charge. 123 Dismantling water tank and removal from site exc 250 ltr and n exc 500 ltr complete all as specified and directed by Engineer-in-Charge. 124 M &L for 500 litres capacity rotational moulded polyethene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge. 125 M &L for 1000 litres capacity rotational moulded polyethene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge. 126 S&F in repairball brass valves, 20 mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. 127 S&F in repair forgun metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. 128 Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer-in-Charge. 129 S&F second class hard wood timber clean swanin scantling on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge. 130 M & L 60mm thick machine pressed with grey cement andpigment interlocking factory made paver blocks of any size and shape conforming to IS 15658-2006(latest revised) , M-35 set, includingpointed in dry sand over 25 mm thick sand cushion complete all as specified and directed by Engineer-in-Charge. 131 M & L for75 mm thick PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in floor etccomplete all as specified and directed by Engineer-in-Charge. 132 M&L for PCC 1:2:4 type B1 (20mm graded aggregate) as in kerbs or mud stops, rounded or chamfered edges, etc complete all as specified and directed by Engineer-in-Charge. 133 Dismantling of cast iron pipe 75/100 mm dia joint in cement mortars and taking out of trench if required complete all as specified and directed by Engineer-in-Charge. 134 S&Ffor 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to wallsincluding suitable clamps after every one mtr of interval with cement joints fixed to wall complete all as specified and directed by Engineer-in-Charge. 135 S&Ffor 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with cement joints fixed to wall including suitable clamps after every one mtr of interval complete all as specified and directed by Engineer-in-Charge. 136 S&Ffor 100mm bore Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. 137 S&Ffor 75mm bore Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. 138 S&F in repair forCI 100mm bends with door complete all as specified and directed by Engineer-in-Charge. 139 S&Fin repair forCI 100mm single branch piece with door complete all as specified and directed by Engineer-in-Charge. 140 S&F in repair forCI 75mm bends with door complete all as specified and directed by Engineer-in-Charge. 141 S&Fin repair for cast iron cowls 100 mm size complete all as specified and directed by Engineer-in-Charge. 142 S & F in repair of stainless steel plate rack 1mm thick for kitchen size 900 x 750 mm as per sample approved by the GE or as directed complete all as specified and directed by Engineer-in-Charge. 143 S&F in repair of sink without drainage board, made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washes and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed by Engineer-in-Charge. 144 S&F in repairsof sink with drainage board, made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washes and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 915X460mm with bowl size 410X330X160mm complete all as specified and directed by Engineer-in-Charge. 145 S&F Mild steel work in framed work such as grills, gratings, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work conforming to Fe 410 -0or Fe 310 -0 including dismantling of old MS work complete all as specified and directed by Engineer-in-Charge. 146 S&F in Repair Steel rolling shutters, 1.25 mm thickness of lath, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer;erected in position as indicated, push pull or manual type complete all as specified and directed by Engineer-in-Charge. 147 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge. 148 S&F steel work in tubular/square/rectangular hollow section/angle iron, tee etc. fortrusses/ purlins & rafters including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete all as specified and directed by Engineer-in-Charge. 149 Dismantling AC/CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer-in-Charge. 150 S & F 0.50mm thickPre-painted galvalume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws complete all as specified and directed by Engineer-in-Charge. 151 M&L for complete removal of existing treatment of old plasteredsurfaces on ceiling including brooming down or steel wire brushing, scraping down and applying two coats ofdistemper oil emulsion over one coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge. 152 Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion by demolition of cement concrete or any type of work and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. 153 Dismantling fencing wire, barbed wire any type complete all as specified and directed by Engineer-in-Charge. 154 Excavation in post holes each not exceeding 0.5 Cum, getting out in soft/loose soil, returning filling in and ramming earth or broken rubble mixed with around earth in layers not exceeding 25 cm thick, watering and removing surplus spoil to a distance not exceeding 50 m and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. 155 M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge. 156 S&F MS angle iron as in fencing posts, struts & "Y" angleholes drilled in for securing wire incl cutting top to shape & with flat iron for securing wire mesh including all necessary drilling, bolting or riveting,weldings etc Fe-290 grade 165 complete all as specified and directed by Engineer-in-Charge. 157 S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, n exc 5cm long dia of shank 5 to 10 mm complete all as specified and directed by Engineer-in-Charge. 158 S&F Mild steel round bar 10 mm dia and over cut to length bend to shape required including cranking bending spirally for hopping for colours hooking ends and binding with a including security bolts post and struts in fencing including cutting top to shape as directed drilling holes notching for wire etc complete all as specified and directed by Engineer-in-Charge. 159 Painting of new steel surfaces of any description not otherwise described n.exc 10cm in width or girth including preparation of surfaces,priming with red oxide zinc chrome primer finished with two coats of synthetic enamelwhen unconnected with other painting or when painted in a different tint complete all as specified and directed. 160 Supply onlychain link MS galvanised fencing of mesh size 50 mm square with 10 gauge wire and not less than @2.92Kg per Sqm complete all as specified and directed by Engineer-in-Charge. 161 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed by Engineer-in-Charge. 162 S&F rolled mild steel grade Fe 290 Gde E-165 quality A for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge. 163 Taking down carefully unserviceable copper/aluminium point wiring(light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover,including taking down of DB’s, meter board any type complete all as specified and directed. 164 Taking down unserviceable sub main wiring with conduits/battens etc complete all as specified and directed by Engineer-in-Charge. 165 M&L for point wiring for following with single corePVC insulated unsheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC concealed conduit, medium grade, ISI markednot less than 20mm dia, concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and modular metal flush boxes alongwith outer cover plate for mounting modular switch, socket and electronic regulator and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with strandedcopper conductor of size 1.5 Sq mm FRLS (Nominal area) complete all as specified and directed by Engineer-in-Charge. Note :- i) Cost for Modular metal flush boxes and modular face plate are deemed to be included in the quoted rate.ii) Cost for cutting, chasing and making good to existing surfaces shall deemed to be included in the quoted rate. 166 One light point controlled by one switch one way complete all as specified and directed by Engineer-in-Charge. 167 One fan/exhaust fan point controlled by one switch complete all as specified and directed by Engineer-in-Charge. 168 One socket outlet 3pin 5 Amp controlled by one switch on independent board complete all as specified and directed by Engineer-in-Charge. 169 One 3 pin 5Amps socket out let point on the same board controlled by one switch complete all as specified and directed by Engineer-in-Charge. 170 One bell point controlled by one bell push 5 Amps complete all as specified and directed by Engineer-in-Charge. 171 One light point controlled by two 2 - ways switches with cables 1.5 sqmm complete all as specified and directed by Engineer-in-Charge. 172 All as per Srl item No 165 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mmstranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and directed by Engineer-in-Charge. 173 All as per Srl item No 165 here-in-before but for one power point 6 pin 15 Amps socket out let with 4.0 Sq mmstranded copper conductor cable PVC insulated including earth wire 4.0 Sq mm copper conductor cable connected to earth dolly complete all as specified and directed by Engineer-in-Charge. 174 S&F of modular switch 1 way 6 Amps one module complete all as specified and directed by Engr-in-Charge. 175 S&Fmodular socket 6 Amps 2/3 Pincombined02 module complete all as specified and directed by Engr-in-Charge. 176 S&F of modular switch one way 16 Amps, one module complete all as specified and directed by Engr-in-Charge. 177 S&F socket modular type 6 amp/16 amps, 2/3 pin combined 02 Module complete all as specified and directed by Engineer-in-Charge. 178 S&F of modular switch 2 way, 6 Amps one module complete all as specified and directed by Engineer-in-Charge. 179 S&F ceiling rose, surface type, 65mm x 50mm, 3 terminal complete all as specified and directed by Engineer-in-Charge. 180 S&F in replacementof electric bell, multi music type, 230 volt AC, single pole complete all as specified and directed by Engineer-in-Charge. 181 S&F of modular bell push 6 Amps one module complete all as specified and directed by Engineer-in-Charge. 182 S&F of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engineer-in-Charge. 183 S&F Fan Step regulator modular type 120W 2 module complete all as specified and directed by Engineer-in-Charge. 184 S&F in replacement of Indoor decorative LED battens- integrated type 20 watt 4 feet white fixture with extruded aluminium body, suitable for LED tube 20 watt , bipin holder, connector block, LED rod 20 watt etc complete with all accessories internally are wired and including connecting up with twin core copper conductor cable complete all as specified and directed by Engineer-in-Charge. 185 S&F in replacement of Indoor decorative LED battens- integrated type 10 watt 2 feet white fixture with extruded aluminium body, suitable for LED tube 10 watt , bipin holder, connector block, LED rod 10 watt etc complete with all accessories internally are wired and including connecting up with twin core copper conductor cable complete all as specified and directed by Engineer-in-Charge. 186 S&F in replacement of LED bulb 12 watt with B22 base fixed in pendent holder /bulk head complete all as specified and directed by Engineer-in-Charge. 187 S&F in replacement of Decorative LED wall bracket light fitting made up of Polycarbonate suitable for B-22 base including one No 12 wattLEDbulb complete all as specified and directed by Engineer-in-Charge. 188 S&F in replacement ofLED weather proof light fitting 18 Watt complete all as specified and directed by Engineer-in-Charge. 189 Supply and fix in replacement of LED bldg security light 35 wattIP 66230V AC outdoor type with high pressure die cast aluminium hosting and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete all as specified and directed by Engineer-in-Charge. 190 S&F in replacement of Single pole and neutral enclosure witha two pin and earth plug and socket complete with one single pole MCB single pole and neutral20 Ampscomplete all as specified and directed by Engineer-in-Charge. 191 S&F in replacement of Indoor decorativeLEDsurface down light12 Wattcomplete with all accessories internally pre wired and including connecting up with twin corecopper conductor cable complete all as specified and directed by Engineer-in-Charge. 192 M&L for sub main wiring withunder mentioned run of single core PVC insulated but unsheathed FRLS cable of specified size multistranded copper conductor 1100 V grade IS-694 drawing into and including rigid non metallic PVC conduit, medium gradeISI marked ( not less than 25 mm) with all conduit fittings & fixing accessories for concealedin wall/ ceiling or surface incl the specified run of specified size earth continuity conductor of similar type of cable complete all as specified and directed by Engineer-in-Charge. Note- The under mentioned runs of single core cable and specified earth continuity conductor andrevelent conduit with fitting accessories will be measured as one run. 193 2 run of 2.5 sqmm and one run of 2.5 sq mm 194 2 run of 4 sqmm and one run of 4 sq mm 195 4 run of 10 sqmm and two run of 10 sqmm 196 M&L in repair for earthing complete for bldgwith galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm diaby means of nuts, bolts, thimbles, check nuts, washers of GI or steel,PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) with fair finish, internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified includingprovision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation andearth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. 197 Supply and fixing in replacement sheet metal enclosure for distribution board TPN 6 way double door, 415 Volt, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and directed by Engineer-in-Charge. 198 S&F in replacement vertical type load line distribution board, double door ,12 way , IP 43IK09AC, 3 phase, 415 volts, TPN bus bar 250 Amps rating and earthbar & din rail with IP 43 rating complete all as specified and as directed by Engr-in-Charge. 199 S&F in replacement ofMCCB, 4 pole 100A, 16KA, 415Volts complete with connections complete all as specified and directed by Engineer-in-Charge. 200 Supply and fixing in replacement of MCB, TPN, 40 to 63A, 10KA complete all as specified and directed by Engineer-in-Charge. 201 Supply and fixing in replacement of MCB, TP, 40 to 63A, 10KA complete all as specified and directed by Engineer-in-Charge. 202 Supply and fixing in replacement of MCB, SP, 6-32A,10KA complete all as specified and directed by Engineer-in-Charge. 203 Taking down old unserviceable LT underground cable any type from trenches , pipes & poles complete all as specified and directed by Engineer-in-Charge. 204 Supply, laying, jointing and testing of70 Sqmm 4 core XLPE insulated, screened, PVC bedded, galvanized steel wire or strip armoured electric power cable (heavy duty) with aluminium stranded conductor 1100 volts grade,laid in trenches, passing through ducts/pipes, fixing along poles complete all as specified and directed by Engineer-in-Charge. 205 Supply, laying, jointing and testing of35 Sqmm 4 core XLPE insulated, screened, PVC bedded, galvanized steel wire or strip armoured electric power cable (heavy duty) with aluminium stranded conductor 1100 volts grade,laid in trenches, passing through ducts/pipes, fixing along poles complete all as specified and directed by Engineer-in-Charge. 206 M&L for Excavation in trenches for hard/ dense soil not exc 1.5 meters wide and not exc1.5 meters deep for pipe line/cables ,getting out and levelling of bottom surface to required level complete all as specified and directed by Engineer-in-Charge. 207 M&L for Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed by Engineer-in-Charge. 208 M&L for Removing excavated material from site to a distance not exc 50 meters away and depositing where directed not exc 1.5 meter from the starting point complete all as specified and directed by Engineer-in-Charge. 209 M&L for dry coarse sand as cushioning to cable 8 cm before laying of LT cable in trenches and 15 cm after laying the LT cable complete all as specified and directed by Engineer-in-Charge. 210 Taking down exhaust fan PVC Body of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades and depositing to MES store yard complete all as specified and directed by Engineer-in-Charge. 211 S&F exhaust fan with louvers PVC body, complete 200mm sweep 230 volts, single phase , AC supply complete with nuts, bolts and washers size of the bolts 06 inch long 6mm dia embedded in the wall including provisioning of flexible cord copper of size 1.5 sqmm three core from ceiling rose to exhaust fan for giving connection and providing continuous earthing connection including opening holes in existing wall and making good as per existing surface complete all as specified and directed by Engineer-in-Charge. 212 M&L in repair of GI pipe light grade 32 mm dia bracket not less than 1.5 Mtr long and bent to a shape forfixing of street lights incl 2 Nos MS clamps made out out of 25x6 mm MS flat including 02 Nos fully threaded bolts and nuts fixing on wall etc complete all as specified and directed by Engineer-in-Charge. 213 Taking down ceiling fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades and depositing to MES store yard including refixing to original position after completion of work complete all as specified and directed by Engineer-in-Charge. 214 Taking down Exhaust fan metal body of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades and depositing to MES store yard incl refixing to original position after completion of work complete all as specified and directed by Engineer-in-Charge. 215 Taking down electric geyser any size including cable connections and disconnecting of fan blades and removing the fan with blades and depositing to MES store yard incl refixing to original position after completion of work complete all as specified and directed by Engineer-in-Charge. 216 M&L for galvanised steel tube light grade of size 40mm dia bore with all fittings complete all as specified and directed by Engineer-in-Charge. 217 M&L for Boring of holes under road, pavement, hard standing by trenchless technology using necessary machine for inserting GI pipe of 40 mm dia complete all as specified and directed by Engineer-in-Charge. 218 M&L for brick laid in trenches for cable protection of burnt clay sub class ‘B’ bricks laid dry flat complete all as specified and directed by Engineer-in-Charge. 219 M & L for Point wiring with single core PVC insulatedbut unsheathed 1.5 Sqmm FRLSH multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVCconduit medium grade not less than 20 mm diaISI marked with all conduit fittings and fixing accessories suitable formounting flush type switches includingmetal flush box and face plate with framefor mounting switches, sockets, fan regulators , etc and earth wire single core PVC insulatedbut unsheathed multistranded copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly in concealed wiring system includes cutting of chasis and making good disturbed surfaces complete all as specified and directed by Engr- in- Chargefor the following :- 220 One light point controlled by one switch one way 221 One fan/exhaust fan point controlled by one switch. 222 One 3 pin 5Amps socket out let point on the same board controlled by one switch complete 223 One socket outlet 5 Amp controlled by one switch on independent board 224 One bell point controlledby one bell push 5 Amps 225 All as per Srl item No 210 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mmstranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and directed by Engineer-in-Charge. 226 M&L for flush typeswitch 1 way 6 Amps 1 module complete all as specified and directed by Engineer-in-Charge. 227 M&L for flush type switch 1 way 16 Amps 1 module complete all as specified and directed by Engineer-in-Charge. 228 M&Lforsocket outlet flush type 6A, 2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge. 229 M&L forsocket outlet flush type 6A/16A, 2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge. 230 S&F in replacement for sheet steel enclosures for MCB distribution board SPN 8 way 240Voltwith 200 Amps bus bar, neutral link, earth bar din rail conforms IS-8822:96 and EIC 898-96, double door complete all as specified and directed by Engineer-in-Charge. 231 Supply and fixing in replacement for MCB, SPN, 40-63A ,15KA complete all as specified and directed by Engineer-in-Charge. 232 Talking up or down GI tubing size 25mm with connection including fittings complete all as specified and directed by Engineer-in-Charge. 233 All as per item No 218 above here-in-before but size 40 mm complete all as specified and directed by Engineer-in-Charge. 234 Supply and fixing GI Tubing medium grade 25mm dia with all fittings any type complete laid in trenches/ on walls/ on ceiling/ roof etc including suitable size of MS Clamps/ saddling on walls/ ceiling etc complete all as specified and directed by Engr-in-Charge. 235 All as per item No 220 here-in-before but size 40mm complete all as specified and directed by Engineer-in-Charge. 236 Supply and fixing in repair gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed, bore of pipe 15 mm including taking down complete all as specified and directed by Engineer-in-Charge. 237 All as per item No 222 here-in-before but size 25mm complete all as specified and directed by Engineer-in-Charge. 238 All as per item No 222 here-in-before but size 40mm complete all as specified and directed by Engineer-in-Charge. 239 M&L for cutting existing steel tubing for alterations or addition and screwing the same size 40 to 50 mm complete all as specified and directed by Engineer-in-Charge.
|
