Tender For Work Of Strengthening The Electrical System By Installing Meters And Main Panel In The Duct Of Fa ... in India

Work Detail

Work of strengthening the electrical system by installing meters and main panel in the duct of Falguni Apartment. - Design manufacturing Supply Installation testing and commissioning of LT METER Panel Board. The Panel shall be fabricated out of 1.6mm thick CRCA sheet steel, painted with Powder coated paint of shade as per the direction of Engineer In-Charge after proper sheet treatment process of sheet steel. The Bus bar of panel shall be of High grade Electrical grade High Conductive Aluminium alloy of appropriate cross section as per rating. The Calculation of continuous rating of Bus Bar shall be submitted. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus Bar supports which shall be mounted on proper interval to ensure bear the jerks of short Circuit as fault level require. All indicating Lights shall be LED type and all wiring shall be done from PVC Insulated copper flexible wire. The Panel shall be complete in all respect and shall consist of following material. PANEL-1, L.T. METER PANEL BOARD, Qty-1No. 2 Incoming 3 MCCB 125 AMP TPN 4 Phase Indicator (R.Y.B) 5 Material (MFM) 6 Alumnium Busbar 7 Outgoing 8 63 AMP 10KA ISOLATOR 07 NOS. 9 Space For 3 phase KWH Meter 07 NOS. 10 Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switcheswith fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter,voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroyticalumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets,compression glands and indicating lamp on incoming etc.The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoingswitches of 100 Amp. and above will be providedwith ampere metre current transformers and selector switches and instrument fuses etc. The switchesboard shall be fabricated with CRCA sheet with aminimum thickness of 1.6 mm/2 mm. Cubicle typeswitch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. 11 INCOMING 12 630 Amp. TPN-1 No 13 125Amp TPN-06 Nos. 14 63A A,p TPN-02 Nos. 15 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.As per PWD schedule 2018 501(s) 16 Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. As per PWD schedule 2018 SI No. 504 (n),(k),(g),(e) 17 300 sqmm 18 150 sqnn 19 50 sqmm 20 25 sqmm 21 Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect As per PWD schedule 2018 Si No. CAT AAA 1413

Contact Information

Other Detail