|
Construction Of Naveen Rajkiya High School At Asalatnagar Jarai, Block Baniyakhera In District Sambhal - Civil works 2 Earth work in excavation in trenches for foundationsand pipes cables etc in ordinary soil (loan clay or sand) including lift upto 1.5 m, leadupto 50 m anddressingof sidesand ramming of bottom anddisposal of surplusexcavated earth as directed by the Engineer- in- charge with in alead of 50m .(Including royalty). 3 In all kind of soil upto 1.5m to 3.0m. depth 4 In all kind of soil upto 3.0m to 4.5m. depth 5 In all kind of soil upto 4.5m to 6.0m. depth 6 Filling of carted earth upto 5km i/c loading, unloading, levelling, watering and compacting etc. 7 Sand filling in plinth including supply of necessary quantity of sand from a distance not excluding 8km from the site of work and including watering dressing etc. rate to include cost of all materials, labour and T&P etc.required for proper completion of the work. 8 Providing and layingin cement concrete 1:4:8 (1 cement :4 coarse sand :8stone grit 40 mm nominal size) and curing complete,including cost ofform- work,in foundation and floors. 9 Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground floor only shall be measured as per I.S.6313 (PartII 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows: (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4)Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 5 liters/sqm 10 R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in lintels of doors and windows excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work. Binding wire cost being included in the itemM-20 11 R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in slab excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work. Binding wire cost being included in the itemM-20 12 R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in beams excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work. Binding wire cost being included in the itemM-20 13 R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in raft foundation and footing excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work. Binding wire cost being included in the item M-20 14 R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in column excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work. Binding wire cost being included in the item M-20 15 Class 150 brick work in1:6cement and coarse sandof 2.25fineness modulus mortar infoundation and plinth including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 16 Class 150 brick work in1:6cement and coarse sandof 2.25fineness modulus mortar in super-structureaboveplinth levelup to floor two level ( up to two storeys ) including necessarycutting and mouldingofbrickworkas required andalsoincludinghoney combed brick work in thickness of wall more than 12cms.including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 17 Class 150 brick work in1:4cement and coarse sandof2.25fineness modulus mortar infoundation and plinth including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 18 Class 150 brick work in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below.including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 19 Paintingon D.P.C. withtwocoatsof airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. 20 Providing and laying "brick coba" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15mm to each other, over 20mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30cm x cm and side wall parapet shall be mono tythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour, T&P etc complete for proper completion of work. 21 Supply and fixing of flush door commercial quality conforming to IS : 2202 (Part I) including fixing of wooden cleats and stopper core and including fixing and adjestment of hings bolts locks handle spring fitting with necessary screw to be supplied. 32 mm thick 22 Add extra for Double Leaf 23 Mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods,gratings etc. ( when notincludedinan overall rates) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing.Fabrication of holdfastfordoor chaukhats and windows. 24 Mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods,gratings etc. ( when notincludedinan overall rates) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing.Fabrication of grill / stairscase railing. 25 Mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods,gratings etc. ( when notincludedinan overall rates) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing.Fabrication of Z-section steel windows. 26 Mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods,gratings etc. ( when notincludedinan overall rates) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing.Angle iron door chaukhats .40*40*5 27 Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work(whennot includedin anover all rates )wroughttorequired shape as necessary including bending for proper completion of thework andincluding supply of steel and wastage andover lapping and hookes. 28 15 mm cement plaster on plinth side ofsingle orhalfbrick wall1 cement : 3 Course sand 29 12 mm cement plasterinsingle coat on fair side ofsingle orhalfbrick wall forinteriorplasteringupto floortwolevel including brick wall for interior plastering uptofloortwo level including internal roundedangles chamfers, and / orroundedanglesnot exceeding80mmin girth and finished even and smooth No. extra for mixing any additive.(1)1 cement : 6Course sand 30 12 mm cement plasterinsingle coat on rough sideofsingle orhalfbrick wall for interior plastering up to floor twolevelincludinginternalrounded angles not exceeding80mm ingirth and finshed even and smooth. (1)1 cement : 6Course sand. 31 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in- Charge. 32 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 33 Cementconcreteflooring1:2:4(1cement:2coarsesand:4gradedstone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 25 mm thick with 20 mm nominal size stone aggregate 34 Providing and laying Vitrified floor tiles (BELL/ KAJARIA/ SOMANI or other standard make) indifferent sizes (thickness 10mm), with a water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ) including grouting of joints with white cement and matching pigment etc. complete.(600x600mm) 35 Providing and laying 6 to 8mm thick ovory or light shadeVitrified floor tiles (BELL/ KAJARIA/ SOMANI or other standard make) indifferent sizes with a water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement :3 coarse sand ) including grouting of joints with white cement and matching pigment etc. complete. (Skirting) 36 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 3 (1 cement : 3 coarse sand)25 mm thick 37 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete 38 Supply and fixing 6 mm. (¼") China white glazed tiles in flooring or in skirting or dado laid with 1:3 Cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and Tools and Plants. 39 Painting Ist coat over priming coat (but excluding cost of priming coat) on steel andothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolitesuperlac,DULUX specified brushingto giveanevenshadeand including cleaningthe surfaceofall dirt,dust and other foreignmatter sand paperingand stopingincluding cost of all materials, labour toolsandplants etc. required forpropercompletion of the work. 40 Painting Ist coat over priming coat (but excluding cost of priming coat) on steel andothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolitesuperlac,DULUX specified brushingto giveanevenshadeand including cleaningthe surfaceofall dirt,dust and other foreignmatter sand paperingand stopingincluding cost of all materials, labour toolsandplants etc. required forpropercompletion of the work . 41 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 42 Distempering(Two coat) withoil bound distemper of approvedbrand and manufacture&ofrequired shadeon undecorated wall surface to give an even shade over &includingapriming coat with cement primer of approvedbrand& manufacture such as Berger,J&N, Shalimar Asian paintsafterthoroughly brushing the surface free from mortar droppings & other foreign matters& alsoincluding preparing the surfaceeven with plaster of paris orapproved synthetic material &sand papered smooth including cost of all materials. 43 Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 44 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 3.8 to 4.7 mm thick glass panes 45 Providing and fixing stainless steel sliding door bolts, ISI markedto required colour or shade, with nuts and screws etc. complete: 300x16 mm 46 Providing and fixing stainless steel tower bolts, ISI marked, to required colour or shade, with necessary screws etc. complete 300x10 mm 47 200x10 mm 48 Providing and fixing stainless steel handles, ISI marked,to required colour or shade, with necessary screws etc. complete : 125 mm 49 Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete 50 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.PWD-13.16 51 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Ordinary cement without any pigment 52 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 53 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar 54 Providing and fixing S.C.I. Tee 150 mm at the inlet and outlet of septic tank. 55 Providing and fixing soil, waste and vent pipes:75 mm diameter Sand cast iron S&S pipe as per IS: 1729 56 Providing & fixing of 75mm dia Sand cast iron S&S as per IS - 1729 terminal guard. 57 Providing & Fixing 75mm plane sand cast iron S&S bend of required drgtee. 58 Providing lead caulked joints to sand cast iron/ cetrifugally cast (squn) irons pipes & fitting of 50 mm dia 59 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter 60 Wiring point for light in PVC conduit with 1.5 sq.mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash 61 Wiring point for fan / fresh air fan (light duty exhaust fan) in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, completewith 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colourwash. 62 Wiring point for plug in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with14 SWG copper earth continuity wire and piano type switch and socket etc., complete in all respect including matching colour wash. 63 Wiring point for call bell in PVC conduit with 1.5 sq.mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting complete with 14 SWG copper earth continuity wire GP Box and piano type bell push or 2 pin socket etc, complete in all respect including matching colour wash. 64 Add for light / fan points with modular type switch in place of piano type switch. 65 Add for plug point with modular switch & socket in place of piano type switch & socket 66 Add for call bell point with modular type bell push in place of piano type bell push 67 Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer. 68 Supply & fixing of power plug with 20A/250 volts flush type modular switch and 5 pin 20 A/250 volts flush type universal modular socket on concealed MS box including supply of all material, labour T&P etc. required for proper completion of the work 69 Supply & wiring of sub main FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable heavy dutyPVC conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting, including matching colour wash etc complete in all respects. 2 nos. 1.5 sq. mm. with 1 no 14 SWG copper earth continuity wire, in 25 mm dia conduit. 70 1 x 4 sq. mm. with 1 no 14 SWG copper earth continuity wire, in 25 mm dia conduit. 71 2 x 4 sq. mm. with 2 no 14 SWG copper earth continuity wire, in 32 mm dia conduit. 72 2 x 6 sq. mm. with 2 no 10 SWG copper earth continuity wire, in 32 mm dia conduit. 73 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 voltes grade.16 sqm .mm 4 core. 74 Supply and fixing and concealing of PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc required for proper completion of the work as per directions and to the satisfaction of Engineer in charge.20 mm dia. 2mm thick 75 S/F of surface / flush mounting SPN Distribution board without MCB complete in all respects as directed at site by Engineer-in-charge. 8 WAYS 76 S/F of surface/flush mounting TPN distribution board without MCBcompletein all respect as directed at site by Engineer-in-charge. (Cat-A) 4 WAYS 77 Supply & fixingof 6/10/16/20/25/32 amp. SP MCB (10 KA) Cat-A 78 S/F of 40 Amp DP MCB (10 KA) 79 Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per directionandsatisfaction of engineer-in-charge. 25 Amp 4 Pole 80 40 Amp 4 Pole 81 Supply&burryingof 600mm x 600mm x 6.0mm G.I. plate, vertically for earthing with its top at least 3 m below ground level complete 20mm dia. G.I.pipe and funnelforwatering and one earthing lead ofno. 8SWGG.I. wirein 15 mm dia. GI pipe uptoswitch board (from apron to switch boardthecost of GI pipe & GI wire willbeextra)300mm square C.I. box with hinged cover,masonary housing alternate layer of charcoal/coke and salt atleast 150mm thick alround etc. as per the direction of engineer in-charge complete in all respect . 82 Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects. 83 Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects. 84 S/F of led Tube Light with batten suitable for up to 1x22 watt LED tube light fitting including tube on surface complete in all respect.Category AAA 85 S/F of led Tube Light with batten suitable for up to 2x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA 86 Supply and fixing of LED STREET LIGHTfitting having die cast aluminium body and diffuser with driver set suitable for 30 Watt to 40 watt . Confirming to IP 66 protection complete in all respect. CAT-AAA 87 Supply and fixing of batten / angle holder complete in all respect 88 Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA 89 Erection and testing of ceiling fan and regulator for room height upto 3.50 meter including supply of 3 mm thick G.I. Rod 19 mm dia. Duly painted, complete in all respect. 90 Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects. 91 Making hole in the wall for exhaust fan and finishing properly complete in all respect. 92 S/F of hexagonal fan box with hexagonal side of approx. 80 mm.in lengthfabricatedfrom 16 SWG M.S. sheet incorporating with10 mm. dia. M.S. round bar duly bent for supporting fan hanger duly painted with redoxideand screwingarrangementwithwiringconduit laid in the R.C.C.roofbeforeconcreting along with supply of all materials,labour, T&P etc. for proper completion of work. 93 Supply & fixing ofelectronic Fandimmer, 300/400 watt, ISI marked, ontheexisting switch board includingmaking connections, required material,labourT/Petc.for proper completionofworkto the satisfaction of Engineer of work. 94 S/F of doorchimeonPolishedM.D.F.E.G. board includingmakingconnectionsetc. complete in all respects. 95 S/F of danger board fabricated from 10 gauge M.S. sheet as per E/I rules. 96 S/Fof shocktreatmentchart ( prescribed under I.E.rules ) duly framed with glass and supported from back with hard board orsoft board with supply of all material labour T & P etc for proper completion of work. 97 Supply of Ceiling fans with fan moter of AC permanent insulation , capacitor rating to conforming BEE 5 star rating & IS 374/79 and aslo comply with IS: 1709/1984 with latest amendment . The rated Voltage 220/240 Volts, 50 Hz I-ph AC assemble should consists of down rod, blades, shackle canopies etc. and wih double ball bearing system . BEE 5 Star Rated - 1200mm sweep 98 Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall beseparate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestaltype for Cat-B and C only.Incoming : 315 Amp. TPN-1 No Outgoing : 100 Amp. TPN-1 No and 63 Amp. TPN-3 Nos Cat. B. Cubicle Type 99 Supply of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX 300mm sweep. 100 Supply and Fixing of LED bulb 9 watt 101 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 102 Same as above but for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware. 103 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requirea)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap. 104 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm 105 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipea) 32mm dia 106 b) 40mm dia 107 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 108 Providing and fixing CP Brass Single lever lelephonic wall mixture of quality & make and as per thedirection of Enginer-in-charge. a) 15mm dia nominal dia. 109 Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. 15mm nominal bore 110 Providing and Fixing C.P. brass Ablution health faucet assembly with 1.0 m long braided PVC hose with mounting bracket fixed on wall complete.[FOR EWC]-Make-JAQUAR ALD-565 111 Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Faucet of approved quality conforming to IS:8931. 15 mm nominal bore-ESSCO SQT 526A 112 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. a) 110mm diameter 113 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. a) 110mm 114 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. a) 110mm 115 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 116 Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes.a) 110mm dia P.V.C. pipe 117 b) 90mm dia P.V.C. pipe 118 Providing & fixing UPVC Floor trap of self cleansing designwith CP Jalicomplete in all respects. (Make : Supreme / Finolex / Prince) P-Trap type Floor Trap 110 x 90mm 119 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince) Door Tee110x110x110 mm 120 110x110x90 mm 121 Bend 110 mm 122 90 mm 123 Providing & fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc. (internal work) Exposed on wall a) 32mm dia nominal bore (medium duty) 124 Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work.a) 32mm dia nominal bore. 125 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (internal work)Exposed on wall a) 25mm dia nominal outer dia pipes 126 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. a) 15mm dia nominal outer dia pipes 127 b) 20mm dia nominal outer dia pipes 128 c) 25mm dia nominal outer dia pipes 129 Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 a) 15mm nominal bore 130 Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. a) 15mm nominal bore 131 Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 a) 15mm nominal bore 132 Providing and fixing gun metal gate valve with wheel of approved quality. a) 25mm dia nominal bore 133 b) 32mm dia nominal bore 134 c) 50mm dia nominal bore 135 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete a) 25 mm nominal bore 136 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. a) Circular Tank 137 Excavating trenches in all kind of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mmdiameter 138 Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes. 160mm dia Under floor (for External sewer) 139 Constructing brick masonry manhole with F.P.S.bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4gradestone aggregate 20mm nominal size); foundation concrete 1:4:8 mix(1 cement : 4 coarse sand : 8 gradedstoneaggregate40 mm nominalsize) insideplastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat ofneat cement completeasper standard design Inside size 90 x 80 cm & 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimension total wt. of cover & frame to be not lessthan 38 kg (wt. of cover 23 kg and wt. of frame 15 kg) 140 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone ggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 141 Providing and fixing square mouth S.W. Gully trapgrade `A" complete with C.I. gratingbrickmasonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 180 x 150 mm. size P type 142 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 143 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. Drilling of 300mm dia bore hole manually. 144 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia 145 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 146 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 147 Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. 148 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge. 149 Constructing brick masonry manhole with 75 class designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix(1 cement :4coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design. a) Inside size 60x60 cm & 90 cm deep including C.I. cover with frame (light duty) total wt. of cover & frame to be not less than 38 Kg (wt. of cover 23 Kg & wt. of frame 15 Kg. 150 Supply & installation of india marka - ii Hand pump with Boring 150 MM dia .60.00 mtr deep,110 mm dia p.v.c casing pipe and const of c.c. 1:2:4 circular plate form complete 151 Supplying, installation, testing and commissioning of Sector panel suitable for following zones,complete with visual indications for short circuit fault,open cricuit fault fire condition zone covered,complete with all connections,interconnections as required. 6 Zone 152 Supplying, installation, testing & commissioning of addressable manual call point complete as required 153 Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. 154 Supplying, installation, testing & commisssioning of ceiling/wall mounted loud speaker, 3/1.5 watt in ABS enclosure complete as required 155 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheathcomplete as required. 156 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size includingconnections and interconnections etc. as required. Speaker cable Four pair, 2 core, 1.5 sqmm. 157 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. 158 Supplying and fixing of Self Glow Exit signage for stairs and exits size 100 x 300. 159 Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC typesuitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-"F" insulation, conforming to IS-325. 6XLWDEOH M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head 160 Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia 161 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/ Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal 162 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISImarked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia 163 Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. 164 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100mm dia 165 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636(type-A) as required : Gun Metal 166 Supplying and fixing first-aid Hose Reel with MSconstruction spray painted in post office red,conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30m 167 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal 168 Supplying and fixing of fire brigade connection ofcast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904as required : 2 way - 100 mm dia M.S. Pipe 169 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. 170 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm dia 171 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore 172 Providing and fixing weather proof standard hose cabinet (900mm x 750 mm x 400 mm) out door type suitable for accommodating yard hydrants made of 1.5mm thick M.S. sheet having central opening glazed door including necessary locking arrangements, painting one coat of primer and two coats of postal red enamel paint and housing 2 Nos. canvas hose pipe and branch pipe as required. (The cabinet shall be floor mounted on suitable raised platform). The shutters are to be lockable type. The words “Fire Hose Cabinet” to be painted on the box. 173 Providing and fixing Fire hose cabinet glazed door shutter and frame with hold fasts ( frame fabricated from 40 x 40 x 5mm and shutter from 35x35x5mm M.S. angle) 1500 mm high x 1000 mm wide with locking arrangement, 4mm thick glass with M.S. flats including all accessories, painting with one coat of steel primer and two coats of postal red enamel paint. The words “Fire Hose Cabinet” to be painted on the box. 174 Providing and fixing air release valve. 175 Supply & fixing of fire extinguishers, ABC type 6.00 Kg capacity (ISI marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 176 Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity(ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 177 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power rollerto achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20 178 Supply & Fixing 80 mm thick Precast cement concrete I-Shape interlocking paver block a with top layer of minimum 8 mm thickness having plan dimension 200x(160+120mm) of O.P. cement, Smooth high gloss finish skid reditantmanufactured from rubber moulds through vibro-compression machanism. the compressive strength of concrere paver block shall not be less Than 30MPA ((M-30) AND wight 5kg per no confirming to IS;15658-2006 with a 4 cm thick layer of fine sandincluding cost of material,labour, T& p TAXES etc. requried for proper completion of the work as directed by Enginner-in-charge. (I)Grey color 179 Drilling of 200 mm dia bore hole. 180 Lowering of 110 mm dia blue casing pipe. 181 Development of tubewell 182 Installation of pump 1.5 HP 183 Shifting of Machine of boring 184 Supply of Blue casing pipe 110mm 185 Supply of Blue casing ripped screen 110mm 186 Supply of P.V.C. end cap 110mm 187 Supply of P.V.C. dori 188 Supply of 32mm G.I. pipe 189 Supply of M.S. Socket 32mm 190 Supply of Boring cover 100mm 191 Supply of Clamp 32mm 192 Supply of 2.0 HPSubmersible pump 193 Supply ofcontrol panel 1.5 /1.0 H.P. 194 Supply of 4.00sqmm cable 195 Supply of 20mm ball valve 196 Supply of 20mm G.I. Nipple 197 Supply & filling of Pgravel in boring out side of PVC pipe complete in all respect 198 Add GST as per Applicable
|
