|
Branch Clamp Type Sl37.2, Tension Bolt Type Nb-2-6 Clamp, Splicing Clamps Splicing Clamp U 859 (4-35, 50-70) Splicing Clamps Are Used To Create Copper And Aluminum Wires Branched From Main Lines With A Voltage Of Up To 660V With Preliminary Removal Of The Insulation At The Installation Site Without Cutting The Conductor., Hardware Press Clamp With Two Holes In The Contact Leg And With A Galvanic Coating Of The Contact Surface, Type A2a 35G-1. For Connecting One Aluminum Or Steel-Aluminum Wire To The Terminals Of The Devices. Clamps Meet The Requirements Of Tu 3449-022-84716711-2009., Clamp Type Al-Cu Sm2.21 Branch, Ps-2-1 Type Connecting Plate Clamp. For Steel Wires And Ropes When Grounding Lightning Protection Cables Of Overhead Power Lines 0.4 — 110 Kv. Clamps Meet The Requirements Of Tu 3449-029-84716711-2009 And Tu 3449-001-52819896-2010. Diameter Of Ropes According To Gost 3062-80; Gost 3063-80; Gost 3064-80 And Ps Grade Steel Wires, Mm-9.1-12.0, Sizes, Mm: A-34, A1-46, B-58, L-70, H-36, R-9, Weight, Kg-0.25, Ps-3-1 Type Connecting Flat Clamp. For Steel Wires And Ropes When Grounding Lightning Protection Cables Of Overhead Power Lines 0.4 — 110 Kv. Clamps Are Produced In Accordance With The Requirements Of Tu 3449-029-84716711-2009 And Tu 3449-001-52819896-2010, Connector Of Aluminum And Steel-Aluminum Wires (Soas) 062-3, Slip22.1 Piercing Clip, Pressed Hardware Clamp With Two Holes In The Contact Leg And With A Galvanic Coating Of The Contact Surface, Type A2a 10G-1., Anchor Clamp Type So118.1202S, Slip22.127 Piercing Clip, Support Clamp Type So130, Hardware Press Clamp With One Hole In The Contact Leg And With Galvanic Coating Of The Contact Surface, Type A1a 70G-1, Apparatus Press Clamp With Two Holes In The Contact Leg And With Galvanic Coating Of The Contact Surface, Type A2a 50G-1 For Connecting One Aluminum Or Steel-Aluminum Wire To The Terminals Of The Apparatus. Clamps Meet The Requirements Of Tu 3449-022-84716711-2009., Nkk-1-1B Type Tensioning Wedge Wedge Clamp Nkk-1-1B Tensioning Wedge Wedge Clamp Is Intended For Fastening Aluminum, Steel-Aluminum And Protected Wires Sip-3, Pzv And Pzvg With A Cross-Section From 10 To 50 Mm2 And Steel Ropes With A Cross-Section From 25 To 50, 45 Mm2 To Tension Suspensions Of Anchor, Anchor-Corner And End Supports. It Is Necessary To Remove The Insulation From The Protected Wires In The Place Of The Clamp. The Strength Of The Wire Seal Is Produced According To Tu 3449-001-52819896-2010. Destructive Load, Kn, Not Less Than 60, Mass, Kg, Not More Than 0.85, Ps-3-1 Type Connecting Flat Clamp. For Steel Wires And Ropes When Grounding Lightning Protection Cables Of Overhead Power Lines 0.4 — 110 Kv. Clamps Are Produced In Accordance With The Requirements Of Tu 3449-029-84716711-2009 And Tu 3449-001-52819896-2010
|
