|
Tender For Special Repair To Or Md Accommodation Bldg No 05 Sqn Area And Special Repair To Civilian Md Accommodation Bldg No 3/F1 At Rts And Depot Saharanpur Under Ge Roorkee.; 1 Taking down cement plaster of any description from brick wall or concrete surface including wall tiling, terrazzo dado/skirting racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. 2 Demolition of cement concrete(unreinforced) and terrazzo floor and paving n.exc 15cm thickness below or above G.L complete all as specified and directed. 3 Demolition of cement concrete (Reinforced) of any description and any position not other wise specifically provided reinforcement cut as required to facilitate demoltion complete all as specified and directed. 4 Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlarfacings dressed stone work and precast concrete articles complete all as specified and directed. 5 Dismantling Asbestos cement corrugated sheets including ridges as in roof coverings complete all as specified and directed. 6 Dismantling wrought iron or mild steel work of any description not other wise provided complete all as specified and directed. 7 Dismantling of wall/ceiling boards any thickness, including cover fillets complete all as specified and directed.. 8 Taking down chowkats or frames n.exc 1.5 Sqm each ( w/o taking of shutter from the frame) and removing from site. 9 All as srl item No. 8 above but exc 1.5 sqm and n exc 4.00 Sqm each. 10 Taking down steel tubing 15 mm bore and connections, including cleaning for refixing or removal from site complete all as specified and directed.. 11 Taking down steel tubing 20 mm bore and connections, including cleaning for refixing or removalfrom site complete all as specified and directed. 12 Dismantling water tankof any capacity (Exc 500 & n exc 1000 ltrs capacity) complete all as specified and directed. 13 S&F Rolled sections as in main beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting platesall as specified and directed . 14 M&L Second class hard wood clean sawn in scantlings fixed in unframed workall as specified and directed. 15 S&F for Pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roofcovering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. 16 S&F for Pre-painted galvaume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roofcovering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. 17 S&F powder coated Everest ceiling grid system of grid size 600x600 mm fixed to walls with rawl plugs and screws and hang to roof members with 3 mm dia GI wire comprising main tee of size 38 mm x 24 mm x 0.30 mm, cross tee of size 28 mm x 24 mm x 0.40 mm with and incl S&F of 4 mm thick everest designer ceiling (E-board clasic) board/tiles for insulation and acoustic purpose 595 x 595 mm size fixed with steples on snap grid as in ceiling complete all as specified and directed 18 Roughening of existing surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. all as specified and directed. 19 M&L PCC 1:2:4 type B-0 using 12.5mm graded agg. 25mm thick finished rough for laying floor tiles complete all as specified and directed. 20 M&L for Coloured (Digital colour) Non skid ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm and not exc 0.18 sqm, in floors etc. including 15 mm thick screed bed or bedding layer in CM 1:6 for laying floor finish, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 21 M&L for joint free coloured glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed. 22 M&L for Vitrified Ceramic coloured tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed in CM 1:6complete all as specified and directed. 23 M&Lfor machine cut kota stone slab flooring 20-25 mm thick over 20 mm thick cement screed (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to get mirror finishcomplete all as specified and directed 24 –ditto- asabove but in vertical surface such as risers of steps , skirting dado and pillar laid with 3.0 kg of cement per sq. metre over & including 10 mm thick rendering in CM 1:4 complete all as specified and directed. 25 M & L for granite 20 mm thick (table rubbed and polished) in cooking platforms and laid over15 mm thick cement screed mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side if required at site complete all as specified and directed. 26 Materials and labour, brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 meter mean radius with old size bricks builtin CM 1:6, complete all as specified & as directed. 27 M&L Brick work with sub class “B” bricks straight or curved on plan to any radius in half brick thick wallsbuilt in CM 1:4 using all as specified using old size bricks 28 M & L for rendering 15mm thick in CM 1:6 on other than fairfaces of brick work or on stone masonry surfaces and finished even and fair without using extra cement complete all as specified and directed. 29 M&L Rendering 15 mm thick in two layer (10 mm and 5 mm thick) in CM 1:4 on external fair faces of brick/concrete work surfaces finished even and fair mixed with W.P.C (WPC shall bemeasured & paid seperately) (without using extra cement)all as specified and directed. 30 M&L 10 mm thick cement plaster in CM 1:4 on ceiling concrete surface facia chajja roof projection etc finished even and fair w/o using extra cement complete all as specified and directed. 31 M&L Three coats of white wash on ceiling surfaces incl preparation of new surfaces complete all as specified and directed. 32 M&L Two coats of white wash on ceiling surface incl preparation of old surfaces complete all as specified and directed. 33 M&L applying two coats of distemper oil emulsion over one coat of primer including preparation on new plastered surface of wall surface complete all as specified and directed. 34 M&L applying one coats of distemper oil emulsion including preparation on old plastered surface of wall complete all as specified and directed. 35 M&L Three coat of white wash on wall including preparation of new plastered surfaces all as specified and directed. 36 M&L for preparation of old plastered surface of wall cornices and pillasters etc and apply two coat of white wash on wall surfcace complete all as specified and directed 37 M&L Two coat ofcement base paint over one coat of primer on wall including preparation of new plastered surfaces all as specified and directed. 38 M&L forpreparation of old plastered surface of wallcornices and pillasters etc apply one coat of cement base paint on wall surfcace complete all as specified and directed 39 S & F pressed steel frame size 105x60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate,etc complete all as specified supplied and fixed. 40 S & F pressed steel frame size 125x60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate,etc complete all as specified supplied and fixed. 41 S&F Mild steel framed work as in doors (as in chowkats) or gates of angle or other section with guest plates rails, braces rail etc inclof steel sheeting or other covering hanging also fastening and fixing complete confirming to Gde Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing. 42 S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. 43 S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat molded plain colour PVC `C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame railswelded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and as directed. 44 M&L for Factory made, 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. 45 S & F 35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc (without sash bar)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.20(a), supplied and fitted to chowkats complete all as specified and directed. 46 M&L fortwo coat of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description, not otherwise described over 10 cm width or girth including preparation ofsurfaces complete all as specified and directed. 47 Supply and fixing 100 mm size butt hinges, medium weight, cold rolled mild steel all as specified and directed. 48 Supply and fix for 200mm long Aluminium, anodised, barrel tower bolts of extruded section all as specified & directed. 49 Supply and fix for 150mm extruded Aluminium alloy handles, cast type all as specified & directed. 50 S & F 300mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed. 51 S & F 140 mm size floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring complete all as specified and directed.. 52 S & Ffor galvanised mild steel wire mess 0.56mm nominal dia of wire and average width of appearature 1.18mm fixed with tinned tack or galvanised wire staples complete all as specified and directed. 53 S & 100 mm long butt hinges (medium weight) colled rolled mild steel fixed to angle iron frame (chowkhat) with welding complete all as specified and directed.. 54 S&F windows made of pre-painted steel ( Base steel as per IS 513 of 0.58mm thick "D" Quality galvanized as per IS 277 withzinc of 120 GSM) and Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thickand and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion shouldbe of 72x50mm, section for fixed glass beading should be of 12x12 mm and section for shutter shouldbe of52x25mm, Outer frame & mullion sections to have rebate for glazed shutters. Fly mesh with 20 mm GI flate beading for provision of guard bars/grill. Flymesh shutter section shouldbe of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixedwith mullion cap. Elixir or equivalent stay, handles 2 nos of heavy duty stainless steel pivothinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and SS mesh for fly mesh shutter with 0.36 mm dia of wire and 1.4 mm aperture. Rubber Gaskets are provided all around the glass. The above frame should be fixed to the concrete/masonry wall by means of self expanding screws. Including 12mm square guard bars with 110mm spacing c/c (Horizontal bay) to be welded on FI 20x6mm alaround except runner portion complete all as specifiedand directed. 55 Material and labour for preparation of new or previously un-treated steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. 56 S & F 25mm dia aluminum anodised curtain rod powder coated teak wood textured finish and wall thickness 1 mm including brackets & end cup complete designed and patterned as approved. 57 S & F 500 ltr capacity rotational moulded PVC water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. 58 S & F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball screwed for iron pipe and fixed complete all as specified and directed. 59 S&F 15 mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceilingor laid in floors including cutting chases in brick/ terrazzo walls exc 10cm girth but n.exc 20cm girth and plastering in CM 1:3complete all as specified and directed. 60 S&F 20 mm bore GI tubing mediumgrade with all fittings to walls and ceiling or laid in floors complete all as specified and directed.. 61 S & F in repair new flxiblePVC waste pipe of 32 mm bore of 750mm / adequate length including one PVC reducer 32mm complete all as specified and directed. 62 S&F in repairs Vitreous China Wash Hand Basin of size 550x400mm (Flat Back or Angle Back type)including 32mm bore (dia) Brass CP Waste Fitting, a pair of Cast Iron Bracket duly painted including cutting and pinning in Ends Making Good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed. 63 S&F in repair Vitreous China White Squatting Pan, ‘ORISSA’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces complete all as specified and directed. 64 S&F in repairs PVC Flushing Cistern 10 LITRE capacity White, Low Level, Valve less, syphonic action type with Inlet, Ball Valve, Float and handle, a pair of Cast Iron Brackets including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed. 65 M&L Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190gms) complete all as specified and directed. 66 S & F 600x450 mm PVC frame beveled edge looking mirror of selected quality glass and fixed with wooden plugs as in repairs complete all as specified and directed.. 67 S & F Bib tap brass CP ( Long body) 15mm bore as in repairs complete all as specified and directed.. 68 S & F CP grating 125mm dia as in repairs with or w/o circular hole for inserting waste pipe complete all as specified and directed.. 69 S & F Angle stop cock fancy type CP with15mm bore as in repairs complete all as specified and directed.. 70 S & F 15 mm bore Concealed stop cock fancy type CP with long shank and cup washer as in repairs complete all as specified and directed.. 71 S & F 20mm bore stop valves cast copper alloy screwed down each high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.. 72 S & F Brass CP shower rose 125mm size with swivel joint as in repairs complete all as specified and directed.. 73 S & F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed. 74 M&L 75 mmPVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed as in repair. 75 S & F Stainless steel sink made out of 1.00mm thick sheet for kitchen or laboratory with plug washers waste pipe couplings brackets overall size495mm x 420mmbowl size410mm x 330mm x 160mmin repairs complete all as specified and directed.. 76 S&F75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring socket ring joints laid in trenches orin floors complete all as specified and directed.. 77 S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Singe Socketed, in any length with Rubber Ring Joints fixed to Walls wit FI clamps made out of 50mm x 3mm complete all as specified and directed. 78 M&LPVC (SWR) bends/shoe for 75mm bore complete all as specified and directed. 79 S& F 75 mm bore PVC (SWR) junction single,(T) equal or unequal complete all as specified and directed. 80 M&L TMT bars6mm to 8mm dia cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed n.less then 0.90mm dia. 81 RCC 1:2:4 type B-1 ( using 20mm graded crushed stoneagg) as in chajjas ,shelvesand similar items complete all as specified and directed.. 82 Form work to chajjas troughs and similar items including edges for rough finished surfaces of concrete flat complete all as specified and directed.. 83 M&L PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in hardstanding, Plinth protection, pathetc 75 mm thick finished even and smooth without using extra cement laid in alternate bey and costuction dummyjoints filled with sand completeall as specified and directed. 84 M&L Cement concrete (1:2:4) type B-1 20mm graded aggregate as in benching roof kerbs and similar items complete all as specified and directed. 85 Taking down old existing water proofing treatment from the top of RCC / arch slab, including taking down exsiting PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed 86 Material and labour for 20mm thick cement paster in CM 1:4 mixed with WPC @ 2% by weight of cement finished even and smooth withour using extra cement on roof surface and wall (WPC will be measured and paid seperately as supply only rate) complete all as specified and directed. 87 Material & labour for preparing new plastered roof surfdace and applying priming coat using with bituminous primer @ 0.30kg per Sqm followedevenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 2mm thickAPP modified polymeric waterproofing membrane minimum weight 3.0 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm perSqm) unrolled & bonded to substrate with side and end laps75mm & 100mm asper manufacturer’s instruction andapplying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat ofbituminous aluminumpaint @ 0.20kg per Sqm as permanufacturer’sinstructions over, completeallas specified & directed. 88 Supply only integral water proofing compound. 89 Dismantling timber scantlings 40 sq. cm and over in section, in any position 90 S &F factory made Flush shutters, solid core construction 30mm thickwith block board core and plywood face panels, commercial type on both sides conforming to IS-2202(Part-I), 1983 complete all as specified and directed. 91 S&F for ISI Marked 150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed. 92 S&Fmild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed. 93 M&L Glazed coloured ceramic tiles (digital 1st quality) in vertical surfaese 300 x 200x7mm thick set in neat cement slurry and pointing in white or coloured cement to match the colour of tiles complete including a coat of neat cement slurry with 3.0 kg of cement per sq. metre including 10 mm thick screed bed in CM 1:4 for dado/ skirting complete all asspecified and directed. 94 M&L for preparation of old plastered surface of wall cornices and pillasters etc including washing, rubbing down and stopping of distempered and painted surfaces and apply two coat of cement base paint on wall surfcace complete all as specified and directed 95 M & L for Plain cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in bed block or hold fast block complete all as specified and directed. 96 M&L for RCC (1:2:4), type B1 (using 20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajja canopies, deck slabs and inshelves and the lik all as complete all as specified and directed. 97 M & L for Formwork to sides and soffits of floor or roof beams, beam hunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished flat surfaces of concrete complete all as specified and directed. 98 M&L PCC (1:2:4) type B-1 using 20 mm grade stone aggregate as in coping, weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed. 99 S&F 15 mmBib taps, chromium plated with butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fiwed complete all as specified and directed. 100 Dismantling timber fillets, posts, Rafter, purlins etc. under 40 sq cm in section complete as specified and directed by Engr-in-Charge 101 M&L PCC (1:3:6) type C-2 using 40 mm grade stone aggregate as in foundation, filling and mass concrete all as specified and directed. 102 M&L for precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and no pigment laid dry over and including a layer of 25 mm thick sand cushioning complete all as specified and directed. 103 M&L Rendering 15 mm thick in CM 1:4 on fair faces of brick/concrete work surfaces finished even and smooth as in drain (without using extra cement) all as specified and directed. 104 Taking down copper/aluminium point wiring (light, fan, socket or power) complete incl fixtures and fittings suze as swithes, ceiling rose, pendant, regulator, sockets, light fitting etc and making good disturbed surfaces of walls, floors etc complete all as specified and directed. 105 M & L for Point wiring in repair with PVC insulated PVC unsheathed electric (FRLS-H) cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of pvc conduit surface casing caping will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including sunk in pressed steel terminal boxes (normal and moduler type) of 1.6 mm thick (duly painted with two coats of black bituminous paint over a coat of red oxide primer in and out sides) with and including plastic laminated bakelite sheet cover of hylam board of 2.8 mm thick including cutting holes for switches, sockets, regulators etc as per requirement including fixing with machine screw, washer etc. 106 One lightpointcontrolled by oneone way switch 107 One fan pointcontrolledby one one way switch 108 One 3/5 pin socket outlet 5 Amp on the same board with other swithes. 109 One 3/5 pin 5 Amps socket outlet on indepandant board. 110 One bell/buzzer point controlled by one push button 111 Allas per item No 105 abovehere inbut with 2.5 Sqmm (nominal area) FRLS-H cable PVC for 15 Amp 3/5 pinsocket power point including 2.5 Sqmm copper conductor green as colour for earth contineuity all as specified. 112 S & F in repair sub main wiring with two runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLS-H) cable of size 6.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20mm/approprite dia with accessories and fittings and one run of 6 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm/approprite dia shall be measured as one run length, Cable required for connection to DBs shall deemed to be incl and shall not be measured separately. Earth wire shall run inside the conduit pipe (Note :- Extra length of cable required for connection to MCBs shall deemed to be included in unit rate.). 113 S&F switch piano flush type polycarbonate single pole one way 6 Amps. 114 S&F switch piano flush type polycarbonate single pole one way 16 Amps. 115 S&F socket outlet polycarbonate 2 in 1, 3 pin 6/16 Amps flush type. 116 S&F socket outlet polycarbonate 2 in 1, 3 pin 6 Amps flush type. 117 S&F ceiling rose 3 phase/PVC/polycarbonate, insulated body. 118 S&F stepped type electrronic fan regulator flush type all as specified. 119 S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for LED Bulbcomplete all as specified and directed. 120 S&F LED Tubelight fitting 1x18/20 Watt surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver complete with all accessories internally prewired and incl connecting upthree core single wire complete all as specified and directed. 121 S&F in replacement of double door MCB distribution boards sheet steel, powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail Single phase and neutral confirms to IS : 13032-1991DB, 240 Volts 200 amps rated busbar 8 way complete all as specified and directed by Engr-in-charge. 122 S&F in replacement of double door MCB distribution boards sheet steel, powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail Three phase and neutral confirms to IS : 13032-1991DB, 440 Volts 200 amps rated busbar 4 way complete all as specified and directed by Engr-in-charge. 123 M&L for MCB single pole,6 to 32 Amp 240 volt B curve 10 KA, IP 20suitable for cable up to 35 Sqmm cross sectional area completeincluding suitable sizecopper Lugs complete all as specified and directed. 124 Supply and fixing amp rating 240V, 10KA "C" curve miniature circuit breaker (MCB) of single pole & nutral and current carrying capacity SPN 40AMP, in the MCB DB complete with connection testing and commissioning. 125 Supply and fixing amp rating 240V, 10KA "C" curve miniature circuit breaker (MCB) of tripple pole & nutral and current carrying capacity SPN 40 to 63 AMP, in the MCB DB complete with connection testing and commissioning. 126 M&L for earthing complete with galvanised steel earth plate electrode 600 x 600x 6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and connectingto main switch or switch boardcomplete and incl PCC masonry pit of 300x300x300mm interier diamentions in PCC 1:2:4 type B1 RCC cover with GI frame, charcoal dust and common salt 15cm in layers all round the earth plate, 20mm dia GIwatering pipe, a funnelwith wire mesh should be provided on top of watering pipe complete all as specified as per electric plate No 3 of SSR 2009 including testing after completion. 127 S&L XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 volt gradecross sectional area 35 Sqmm and 3.5 core, including taking down of existing unserviceable service cable all as specified and directed. 128 M&L for laying GI tubinglight grade 40 mm dia with all fittings for cable protection including GI clamps nut bolts and washer etc complete all as specified and directed. 129 Excavating in trenches, in any type of soilnot exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed. 130 Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed. 131 Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. 132 M & L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable all as specified and directed. (Note:- Punning thickness shall be measured) 133 Material and labour for Brick protection with sub class ‘B’ bricks old size, laid dry, flat over cable, perpendicular across the cable in trenches complete all as specified and as directed. 134 Supply and fixing building security lights with new generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver type street light fitting 35 watt capacity LED and including all accessories duly pre-wired, fixing on existing bracket with nut, bolts & washers as required at site for fixing of street light on LT pole/ wall complete including taking old street light fitting any type and description complete all as specified and directed. 135 M&L for bracket made of GI light grade pipe 1.2 Mtr long of size 32/40 mm bore bend to shape as per site requirement fixed to pole with 40 x 5 MM-02 Nos, size clamps bolts, Nuts, washers including painting two coats of aluminium paint over a coat of primerall as specified and directed. 136 S&F in replacement of double door MCB distribution boards sheet steel, powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail Single phase and neutral confirms to IS:13032-1991DB, 240 Volts 200 amps rated busbar 4 way complete all as specified and directed.
|
