|
Addition Alteration Of Qtrs Type H P At Shankar Vihar Under Ge South Delhi Cantt 10-- 1 M & L for Providing and injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. 2 M & L for Anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed. 3 Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition (Parapet wall) complete all as specified and directed. 4 M&L for reinforced cement concrete (Design mix) M-25 (using 20 mm graded stone aggregate) as in fins, slab ,fascias, louvres, parapets, and railings, newels, balustrade, and the like complete all as specified and directed. 5 S&F TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length bent to shape required including cranking, bending, spirally hoping for columns, hooking ends and welding the new reinforcement with old steel bars complete all as specified and directed. 6 S&F 8mm dia TMT bars, cut to length bent to shape requiredincluding cranking bending spirally for hoping for columns, chajjas to parapets etc hooking ends and binding with and including mild steel wire (annealed)not less than 0.90mm dia complete all as specified and directed. 7 M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc. vertical or to better, for fair finished surfaces of concrete complete all as specified and directed. 8 M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed. 9 M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part ofsand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete as directed at site Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer).(c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account. 10 M&L Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6),(up to two story Bldg) complete all as specified and directed. 11 M&L Brick work with sub class "B" bricks , straight or curved on plan in half brick thick wallbuilt in cement mortar (1:4), (up to two story bldgs) complete all as specified. 12 M & L for Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and directed. 13 M & L for Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg including necessary scaffolding arrangement complete all as specified and directed (whether full thickness removed or only a part there of) and removing from cantonment area or as directed complete all as directed by Engr in charge and specified. 14 M&L forCement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof pedding, finished even and smooth without using extra cement, including cleaning the concrete surface by steel wire brushes, up to three stories bldgs, complete all as specified and directed. 15 M&L for APP based polymeric membrane granular finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints complete all as specified and directed. 16 S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner complete all as specified and directed. 17 M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete as directed. 18 Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons, skirting etc laid bedded and pointed in any morter complete all as specified and directed 19 M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished in single piece) in steps, jambs, pillars, cooking platforms, skirtings with necessary hole for gas pipe where ever required and likes over and including cement mortar bedding of 20mm thick in CM 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and directed. 20 M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished in single piece) in steps, riser/skirting, jambs, pillars, window cills, and like over and including 20mm thick screed bed in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and incl making grooves 3 Noscomplete all as specified and directed. 21 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off thepremises complete all as specified and directed. 22 M & L for Glazed Ceramiccoloured tiles in vertical surface 450X300X7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed bed of cement mortar in (1:4), completeall as specified and directed 23 M&L forVitrified Ceramic tiles,double charged, light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. 24 M&L for vitrified ceramic tiles double charged (light shade) 10 mm thick (Square/ rectangular) area of each tile exceeding 0.42 but n. exc 1 sqm as in skirting over and including 10mm thick cement plaster in CM (1:4) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cementto match the shade of tiles complete all as specified and directed. 25 M&L Non Skid ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15mm thick in CM 1:6 complete all as specified and directed. 26 M&LNon skid coloured ceramic of size 600mmx600mm tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 sqm, as in skirting over and including 10 mm thick screed bed in CM (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cementto match the shade of tiles complete all as specified and directed. 27 S&F in repair Vitreous china wash down water closet pan sinlge piece syphonic action, white fixed in repair,including soft close sheet cover of closed pattern with flat bottomcomplete. Cat part No Hindware 20121 or equivalent including dual action flushing cistern viterous china, 10 ltr capacity complete all as specified. 28 S & F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including provision of lime concrete bedding complete.Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete. 29 S&F in repairs low level flushing cistern of 10 ltrs capacity PVC valveless, syphonic action type, white with inlet ball valve float and handle complete all as specified. 30 S&F in repair CP brass health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete. 31 S & F in repair Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed in repairs to walls with chromium plated brass screws complete. 32 S & F in repair Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete. 33 S&F in repairs elegent mirror PVC cabinet without towel rail of size 422 x 622 mm all as specified. 34 S & F Bevelled edge mirror of 5 to 6 mm thick selected quality glass, 600 x 450 mm size,and fixed to wooden plugs with Chromium plated brass screws and cup washers, complete. 35 S&F in repairs stainless steel foldable towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls complete all as specified and directed. 36 S&F in repairs brass chromium plated shower rose of size 125 mm with long arms (300 to 450mm long) including fixing to uPVC pipes. 37 S&F in repairs 6 mm thick glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge) 38 S&F in repairs wash hand basinmixer15mm dia CP brass fancy type including joints to steel pipe or unions all as specified. 39 S & F in repairs Brass CP Wallmixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for uPVC pipe15 mm bore and fixed complete all as specified. 40 S&F in repairs Kitchen sinkmixer15mm dia CP brass fancy type including joints to uPVC pipe or unions all as specified. 41 S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece complete. 42 S&F in repair15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed complete. 43 S&F in repairs Good quality Connecton pipe (PVC) 15 mm dia and 450/600mm long complete all as specified. 44 Dismantling of floor of area exc 1.5 Sqm and not exceeding 5.00 Sqm for EWC water closetand removing out the cinder/concrete from sunken protion, grinding any sharp edges etc all as specified and directed with following steps: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite.(c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified.(d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall.(e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(f) The area of Each WC portion is n.exc 5.00Sqm each.(g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.(h) 72 hrs Ponding test shall be carried out for sunken treatment before payment. 45 Dismantling of floor of area not exceeding 1.50 Sqm for EWC water closetand removing out the cinder/concrete from sunken protion, , grinding any sharp edges etc all as specified and directed with following steps: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite.(c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified.(d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall.(e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(f) The area of Each WC portion is n.exc 1.50Sqm each.(g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.(h) 72 hrs Ponding test shall be carried out for sunken treatment before payment. 46 Taking down (Door) chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete. 47 Taking down shutter of any description exc 1.00 sqm but n.exc 2.00 sqm each complete all as specified and directed.. 48 Taking down chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete. 49 Refixing of shutters of size exc 1.00 sqm but n exc 2 sqm in same or other opening including all necessary adjustments to fit the shutter with frame like easing of shutter for easy closing /opening, tightning of hinges or changing the position of hinges adjustments of tower bolts, Sliding bolts etc complete all as specified and directed. 50 S & F Pressed steel frames of size 105mm x 60mm for doors/cupboard with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete. 51 M & L for Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in back filling, holdfasts etc, complete all as specified and directed. 52 S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr incharge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. 53 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item). 54 Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer"s specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item 55 S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr incharge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. 56 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headedcounter sunk S.S screws, all as per direction of EngineerIn- Charge.(Note: stainless steel butt hinges shall be paid separately under relevant item). 57 Dismantling wrought iron or mild steel/cast iron work of any description (steel window & Grill)complete all as specified and directed. 58 S&Ffabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mm x 44.45mm x 1.5mmthick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc includingjointing cleats for fixing builder"s hardware fittings & 4 mm thick selected quality frosted or plain glass including necessary fittings/ fixture /aluminum snap beads complete all as specified.Note: (a) Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.(b) Cost of glass and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid. 59 S&Ffabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mm x 44.45mm x 1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc includingjointing cleats for fixing builder"s hardware fittings & stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staplesincluding necessary fittings/ fixture /aluminum snap beads complete all as specified.Note: (a) Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.(b) Cost of SS wire mesh and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid. 60 M&L powder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mmthickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section(two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: (a)For Provn of fixing window AC , clear opening shall be divided horizontally at appropriate height / as directed byEng-in-Charge i.e whole opening shall be divided in two portion and measurement shall be taken for clear opening i.e. out to out of window opening as a whole including all fittings and fixtures and no extra shall be paid separately .(b) Cost of glass, SS wire mesh and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid. 61 M & L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders,framed balusters,walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified. 62 M & L for preparation of new Steel surfaces of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified. 63 S & F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified. 64 M & L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and apply one coats of synthetic enamel paintall as specified and directed 65 M & L for preparation of old Steelsurfaces of any description not otherwise described over 10 cms width or girth and apply one coats of synthetic enamel paint all as specified. 66 M&L for preparation of old painted Steel surfaces exc 10cm width or girth and applying one coat of aluminiumpaint of approved shade/tint 67 S&F 100mm long (size) butthinges, stainless steel AISI 304 grade with brass/bronze hinge pin complete 68 S&F stainless steelAISI 304 grade barrel tower bolt 200mm long, extruded section,etc. complete all as specified and directed. 69 S&F stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and directed. 70 S&F Stainless steel of AE SI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete. 71 S&F Magic eye and fixed to doors all as specified and directed complete. 72 S & F Hasp and staple -100mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete. 73 S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60mm complete. 74 S&Fin repair 25 mm diaSS curtain rod , with fixingbrackets, side knobsof good quality as approved complete all as directed. 75 Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete. 76 M & L for Plain Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete. 77 Taking up or down steel tubing and connections all as specified. 78 15 mm bore 79 20 mm bore 80 25 mm bore 81 Supplying and laying of CPVC 20mm outer dia pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete all as specified complete with fitting as required. 82 Supplying and laying of CPVC 25 mm outer dia pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete all as specified complete with fitting as required. 83 Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres complete. 84 Dismantling water tanks of capacity exceeding 250litres but not exceeding 500 litres complete. 85 S&F 500 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position all as specified. 86 S&F 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position all as specified. 87 S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete. 88 S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete. 89 S & F in repairs Sinks with drainage board made of 1mm thick stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, includingPVC waste pipe 32 mm bore, 65 cm long complete. 90 S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm. 91 Dismantling of cast iron or reinforced concrete drains pipes , jointed in cement morter and taking out of trenches if required up to 100 mm internal dia of drains, complete all as specified and directed. 92 S&F 110 mm uPVC pipes Type "B" (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed. 93 S&F 75 mm uPVC pipes Type "B" (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed. 94 Taking down eaves gutters and rain water pipes (any size, material or pattern), including all fittings , heads, shoes, bends,swann necks, etc including taking out of trenches if required for cleaning or refixing or removal to store complete all as specified. 95 S&F 110 mm uPVC pipes Type "A" (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. 96 S&F 75 mm uPVC pipes Type "A" (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. 97 S&F 110 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required complete all as specified and directed. 98 S&F 75 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required complete all as specified and directed. 99 S&F in repairs uPVC multi floor trap with grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed. 100 S & F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete. 101 Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etcincluding removal of debrish from the MOD land complete all as specified and directed. 102 M&L for cement plaster 15mm thick in CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer"s recommendations including all levelling the surface, curing etc complete. NOTE : Rates for water proofing compound/ polymer deemed to be included in the above rates. 103 M&L for providing and applying a bond coat of Latex:Water:cement - 1:4:6consumption @100gm/sqm on the brick wall surface by brush as per manufacturer"s recommendations including curing complete. 104 Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer"s instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge.Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealent.Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements. 105 Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injcection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line 106 M&L for 15 mm thick rendering in cement mortaron fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 )mixed with WPCfinished even and fair etc complete all as specified and directed.(Note:- WPC shall be measured and paid seperately.) 107 M&L rendering 10 mm thick in CM 1:6 on internal brick/concrete wall surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as specified and directed . 108 M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and fair without using extra cement complete all as specified and directed. 109 M&L for preparaing newly plastered surfaces of walls and applying three coats of white wash complete. 110 M&L for preparation of the newly plastered surfaces of walls/ceiling andapplying wall care putty of 1 mm thickness over plastered surfaces to prepare the surface even & smooth to receive primer and applying one coat primer and two or morecoats Distempering OBD (ready mixed)having VOC content less than 50 gms/ltr, of approved manufacturer, of required shade & colour complete all as specified .gms/litre, of approved manufacturer, of required shade and colour complete all as specified. 111 M&L for preparation of the old decorated surfaces (plastered or unplastered) of walls/ceiling by complete removal of existing treatmentby mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surfaces to prepare the surface even & smooth to receive primer and applying one coat primer and two or more coats Distempering with OBD (ready mixed)having VOC content less than 50 gms/ltr, of approved manufacturer, of required shade & colour complete all as specified .gms/litre, of approved manufacturer, of required shade and colour complete all as specified. 112 M&L for preparation of newly plastered surfaces of walls and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primerapplied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge. 113 M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two ormore coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primerapplied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge. 114 Dismantling boarding, any description, fixed in any position with nails. 115 S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets. 116 S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbmhaving good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets. 117 S & F CP clip on hinges (Inset) complete all as specified and directed . 118 S&F15mm mild steel, chromium platedrod with fixing brackets, fixed in cupboardsfor hanging cloth of adequate strength all as specified and directed. 119 S&F stainless steel AISI 304 grade handle of size 100 mm long,etc. complete all as specified and directed. 120 S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw.complete all as specified and as directed. 121 M&L for cleaning the sides rolling shutter shafts guide channel and greasing of moving parts of rolling and straightening rolling and replacement of bolts nuts etc as required for smooth functioning of shutters and taking out existing rolling shutters if required and refixing the same in original position complete all as specified (opening of shutter exc 2.00 m and not exc 3.50 m and area exc 6.00 sqm and n.exc 9.00 sqm all as specified) 122 S& F in repairs mild steel spring conforming to IS 62A-1970 of approved make in existing rolling shutters/opening of shutters exc 2.00 m and n.exc 3.5 m all as specified. 123 S&F in repair steel rolling shutters, thickness of lath 1 mm, with out ball bearing, top cover, anchoring rod and hasp & staple, erected in position where required (in patches or whole), complete push pull or manual type complete as directed 124 S& F staianless plate rack made of 1 mm thick stainless steel sheetof size 750 mm x 900 mm x 210mmconsisting of 3 shelf for bowls and one shelf for keepingsix nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE"s officeall as specified and directed by engr-in-chargecomplete. 125 S & F Continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified. 126 S&F in repair bib tap standard of PTMT any color high pressure screwed for iron pipe and fixed to 15mm bore. 127 S&F in repair stop valve standard of PTMT any color high pressure screwed for iron pipe and fixed to 15mm bore. 128 S&F in repair stainless steel telescopic channel of size 300 mm to 500mm complete all as specified and directed 129 S&F stainell steel thali basket for kitchen cabibnets of suitable size and shape complete all as specified & directed. 130 M&L Packing and transportation of luggage (approx 6 tonne) within 10 km radius to include:- (a) Removal from old locationand fixing such asAC (01), TV (01), Washing machine (01), RO (01),Dish Antena (01) Dish washer (01) atnew location transportation. (b) Transportation of 2 wheeler and four wheelers not included.
|
