|
Tender For Strengthening And Upgredation Of Krishi Vigyan Kendra, Bichpuri In District- Agra (U.P.), 1 FARMER HOSTEL Excavation in foundation in ordinary soil incl. lift up to 1.5M and lead upto 30m and incl. filling, watering and ramming of excavated earth in to the trenches or in to the space between the building and the sides of foundation trenches or into the plinth and removal & disposa of surplusearth as directed by the Engineer incharge. 2 Filling of carted earth Lead upto 15 Km Distance 3 Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 kms. from the site of work and including watering, dressing labour T & P etc. required for proper completion of work. Sapling of girth upto 30cms. measured at a height of 1.5 M). 4 Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors. 5 Antitermite treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart @ 100 Nos Holes per 9.00 Sqm. including drilling 12 mm diameter holes and plugging also to match the floor properly :With Chlorpyriphos / Lindane E.C. 20% with 1 % concentration. 6 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in lintel beamsGround Floor 7 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in lintel beamsFirst Floor 8 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in lintel beamsTerrace Floor 9 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for slabs Ground Floor 10 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for slabs First Floor 11 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for slabs Terrace Floor 12 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for theplinth& slab beams. Ground Floor 13 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for theplinth& slab beams. First Floor 14 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) for theplinth& slab beams. Terrace Floor 15 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) inR.C.C.foundation and footingwithapproved stone ballast. 16 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in R.C.C. columns Ground Floor 17 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in R.C.C. columns First Floor 18 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in R.C.C. columns Terrace Floor 19 First class brick work in 1:6 cement and coarse sand mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. 20 Providing & aplying a coat of residual petroleum bitumin of grade VG 10 of approved quality using 1.7 kg per SqM on DPC after cleaning the surface with brushes and finally with piece of cloth lightly soaked in kerosine oil. 21 First class brick work in 1:6 cement and coarse sand mortar in super-structureincludingnecessarycutting and moulding of brick work asrequired thickness of wall more than 12cms. (1:6 cement : coarse sand)Ground Floor 22 First class brick work in 1:6 cement and coarse sand mortar in super-structureincludingnecessarycutting and moulding of brick work asrequired thickness of wall more than 12cms. (1:6 cement : coarse sand)First Floor 23 First class brick work in 1:6 cement and coarse sand mortar in super-structureincludingnecessarycutting and moulding of brick work asrequired thickness of wall more than 12cms. (1:6 cement : coarse sand)Terrace Floor 24 First class brick work in 1:4 cement and coarse sand mortarin1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work.Ground Floor 25 First class brick work in 1:4 cement and coarse sand mortarin1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work.First Floor 26 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. Ground Floor 27 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. First Floor 28 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. Terrace Floor 29 15mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. Ground Floor 30 15mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. First Floor 31 15mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. Terrace Floor 32 12mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. Ground Floor 33 12mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. First Floor 34 12mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. Terrace Floor 35 Making grooves 10 to 12 X 12mm and upto 25 X 15 mm deep in plaster of the walls or in ceiling vertically or horizontally as required. 36 Providing and laying Ceramic glazed floor & wall tiles tiles (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 37 Cement concrete flooring 1:2:4 (1 cement : 2 coars sand : 4 graded stone of size 20mm nominal size) laid in one layer finished with floating coat of neat cement (40mm thick floor) For plinth protection 38 Providing and fixing of glass strip of 4mm thick in joints of floor and skirting at the time to laying including labour T & P etc complete in all respect. (b) of 40mm depth. 39 Marble stone flooring with 20mm marble stone as per sample of marble approved by Engineer-in-charge, over 20mm (average) base of cement mortar of 1:4 (1 cement : 4 coarse sand) laid and jointed with gray cement slurry including rubbing and polishing complete with: white albetta white stoneGround Floor 40 Marble stone flooring with 20mm marble stone as per sample of marble approved by Engineer-in-charge, over 20mm (average) base of cement mortar of 1:4 (1 cement : 4 coarse sand) laid and jointed with gray cement slurry including rubbing and polishing complete with: white albetta white stoneFirst Floor 41 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws, steel handles, sliding bolt, door stoper & tower bolt. 35 mm thick 42 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws, steel handles, sliding bolt, door stoper & tower bolt. 35mm thickDouble leaf 43 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Providing & fixing of hold fast for chaukhatsof doors and windows. 44 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Providing & fixing of door / windows grill. 45 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Z-Section steel windows (openable) 46 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Angle iron door chaukhat 40*40*5 47 Providing and fixing fly proof wire gauge to windows and clerestory windows & doors with MS flat 15*3mm and nuts bolts complete. 48 Fixing of Door, windows/ventilators chaukhats in position.Door chaukhats 49 Fixing of Door, windows/ventilators chaukhats in position.Window chaukhat 50 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Internal wall surface)Ground Floor 51 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Internal wall surface)First Floor 52 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Internal wall surface)Terrace Floor 53 Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.67 Ltr/10 sqm including one coat of primer applid @ 2.2 Ltr/10 sqm coat curing and cost of all material, labour, T & P etc. required for proper completion of work for two coat. Ground Floor 54 Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.67 Ltr/10 sqm including one coat of primer applid @ 2.2 Ltr/10 sqm coat curing and cost of all material, labour, T & P etc. required for proper completion of work for two coat. First Floor 55 Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.67 Ltr/10 sqm including one coat of primer applid @ 2.2 Ltr/10 sqm coat curing and cost of all material, labour, T & P etc. required for proper completion of work for two coat. Terrace Floor 56 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Ceiling)Ground Floor 57 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Ceiling)First Floor 58 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Ceiling)Terrace Floor 59 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 60 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth ofapproved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 61 Painting with synthetic enamal paint of approved brand and manufacturer of required color to give an even shade: two or more coats on new work over and undercoat of suitable shade of ordinary paint of approved brand & manufacturer. The item shall also include applying priming coat with ready mixed red oxide zinc chromate primer of approved brand & manufacturer. 62 Painting with synthetic enamal paint of approved brand and manufacturer of required color to give an even shade: two or more coats on new work over and undercoat of suitable shade of ordinary paint of approved brand & manufacturer. The item shall also include applying priming coat with ready mixed red oxide zinc chromate primer of approved brand & manufacturer. but on new wood surface. 63 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 64 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 Kg/Sqm mixed with water proofing cement compound @ 0.253 Kg/Sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with water proofing cement compound @ 0.126 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 65 Providing & fixing white vitereous china water closet squatting pan ISI marked (Indian type W.C. pan) with 100mm sand cast iron P or S trap, 10/12.5 litrsPVC low level flushing cistern with fittings & brackets 40mm dia C.P. flushpipe with fitting & clamps, 20mm over flow pipe with specials and mosquito proof coupling of approved municipal design, painting wherever required including cutting & making good the walls & floors where required.Orissa Pattern W.C. pan of size580x 440mwith integral type foot rests flush pipe and over flow arrangement. 66 Providing & fixing white vitereous china water closet squatting pan ISI marked (Indian type W.C. pan) with 100mm sand cast iron P or S trap, 10/12.5 litrsPVC low level flushing cistern with fittings & brackets 40mm dia C.P. flushpipe with fitting & clamps, 20mm over flow pipe with specials and mosquito proof coupling of approved municipal design, painting wherever required including cutting & making good the walls & floors where required. Europion type W.C. pan with black plastic seat and lid Make, Cera, Hidustan 67 Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mmC.P. brass waste of standard pattern including cutting & making good the walls wherever required.Flat back wash Basin size 630x450 mm with single 15mm C.P. brass pillar tap. 68 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. 32mm dia 69 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.40mm dia 70 Providing and fixing 1500x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 71 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm 72 Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm Nominal bore 73 Providing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing Not less than 190 gms. 74 Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing Not less than 105 gms 75 Providing and fixing PVC pipe Conforming to IS make Working Pressure 6 Kg/sqcm including testing labour T&P and all Complete fitting.110mm diameter 76 Providing and fixing PVC pipe Conforming to IS make Working Pressure 6 Kg/sqcm including testing labour T&P and all Complete fitting.140mm diameter 77 Providing and fixing PVC Plane band of required degree 110mm diameter 78 Providing and fixing PVC Plane band of required degree 140mm diameter 79 Providing and fixing PVC Tee 110mm diameter 80 Providing and fixing PVC Tee 140mm diameter 81 Providing and fixing PVC Nahani trap for self cleaning design with screwed down on highed grating with or without bend arm complete 82 Construction of main Hole cover of internal size of 900x800x450mm complete fitting 83 Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc.Exposed of wall20mm dia Nos.minal bore (medium duty) 84 Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc.Exposed of wall25mm dia Nos.minal bore (medium duty) 85 Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc.Exposed of wall32mm dia Nos.minal bore (medium duty) 86 Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.15mm Nos.minal bore 87 Providing & fixing CP brass short body of approved quality conforming to IS 8931 15mm Nos.minal bore 88 Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing Nos.t less than 690 gms.15mm Nos.minal bore 89 Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia Nos.minal bore 90 Providing and fixing gun metal gate valve with wheel of approved quality.32mm dia Nos.minal bore 91 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm Nos.minal bore 92 Providing and fixing 15mm C.P Brass elvo of approved make and quality as per direction of engineer-in-charge 93 Providing and fixing C.P Brass extension nipple (size of 15mm to 50mm) of approved make and quality as per direction of engineer-in-charge 94 Providing and fixing C.p Brass stop cock of standard design of approved quality 95 Providing and fixing C.P brass shower of approved quality 96 Providing and fixing ball valve (brass) of approved quality15mm Nominal size 97 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 98 Providing and fixing 50 Ltr ElectricGeyser 99 Wiring points for light with 1.5 Sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit with 1.5 Sqmm FRPVC insulated copper conductor cable as earth wire drawn inside light paintswith modular Box and cover plate 100 Wiring point for two way light 1.5 Sqmm FRPVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5Sqmm FRPVC insulated multistrand copper conductor cable as earth wire drawn inside 2 way light paint with modular Box and plate 101 Wiring point for fan / fresh air fan (light duct exhust) with 1.5 Sqmm FRPVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5Sqmm FRPVC insulated multistrand copper conductor cable as earth wire drawn inside 2 way light paint with modular Box and plate 102 Wiring point for plug with 1.5 Sqmm FRPVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth with drawn , modular type switch & socket complete in all request with modular Box and cover plate 103 Wiring point for call ball with Wiring point for plug with 1.5 Sqmm FRPVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth with drawn , modular Box and cover platecomplete in all request with modular Box and cover plate 104 Wiring point for H.P.M.Y. Sodium vapour lamp with 1.5 Sqmm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 Sqmm FRLSH PVC insulated Multistrand copper conductor cable as earth wire drawn inside the conduct 15 Amp modular type switch etc. complete in all respects with modular Box and cover plate 105 Supply & wiring of submains with two number 4 Sqmm FRLSH PVC insulated 1100 volt grade multistrand single core copper conductor cable in 20 mm dia. Havy duty (2mm thick) PVC conduct with one Nos.. 2.5 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth continuty wire drawn in conduit complete all respect. 106 Supply & wiring of submains with two number 6 Sqmm FRLSH PVC insulated 1100 volt grade multistrand single core copper conductor cable in 25 mm dia. Havy duty (2mm thick) PVC conduct with one Nos.. 4 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth continuty wire drawn in conduit complete all respect. 107 Supply & wiring of submains with four number 10 Sqmm FRLSH PVC insulated 1100 volt grade multistrand single core copper conductor cable in 25 mm dia. Havy duty (2mm thick) PVC conduct with two Nos.. 6 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth continuty wire drawn in conduit complete all respect. 108 Supply and laying of aluminium conductor PVC armoured served sheathed cables 1100 volts grade at a depth of 750mm below ground lecel over a cushion of 75mm . Thick sand all around and protected with brunt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-incharge , complete in all respect . the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 35 sq.mm 3-1/2 core 109 Supply and laying of 25mmX3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. 110 Supply and burring of safe Earthing electrode T-19 (hot dip galvanized) length up to 3000mm , outer pipe 50mm , inner pipe 25, terminal Dia 12mm , outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 Kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 20 x 3 G.I.strip , up to switch board (from apron to switch board , the cost of G.I. stip will be extra ) along with 30 cm square C.I. frame with hinged cover & masonry housing . 111 Supply and Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting , M.S channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB"S (four pole 36 KA with thermal magnatic release ) Switches complete and instrument chamber etc. complete in all respect.Incoming. 200 Amp. MCCB-1 Nos.Outgoing 100 Amp. MCCB-2 Nos.. 112 Supply and fixing 6 Amp. To 32 Amp. SPMCB (10KA) 113 Supply and fixing 50Amp. To 63Amp. SPMCB (10KA) 114 Supply and fixing 40 Amp. DP MCB (10KA) Cat -B ( For light D B) 115 Supply and fixing 80 Amp. To 100 Amp. 4 Pole MCCB (16KA) Thermal Magnetic release 116 Supply and fixing Surface /flush mounting 12 ways SPN distribution board with additional MCB complete in all respect as directed at site by engineer - incharge . 117 Supply and fixing Surface /flush mounting 4 ways SPN distribution board with additional MCB complete in all respect as directed at site by engineer - incharge . 118 Supply and fixing of call bell of approved make on polished MDFEG / Teak ply board including making connections etc. complete in all respect. 119 Erection and testing of ceilling fan and regulator etc. excluding supply of down rod, complete in all respect. 120 Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts , nuts and washers etc. complete in all respect. 121 Supply and fixing of 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect . 122 Supply and fixing of power plug with 20Amp. /250Volt flush type modular switch and 5 pin 20A/250V flush type universal modular socket switch on concealed M.S. box including supply of all material , labour T&P etc. required for proper completion of work. 123 Supply and fiixing hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16SWG MS Sheet incorporating 10mm dia M.S. round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all material , labour . T&P etc. required for proper completion of the work . 124 Supply and fixing of electronic fan regulator (modular) 120-280 V. ISI marked , on the existing switch board including making connections , required material, labour T&P etc. for proper completion of work to the satisfaction of engineer in charge of work 125 Supply and wiring of submain with two number 1.5 sq. mm FR PVC inculated 1100 V grade multistrand single core copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit with 1 Nos. 1.5 sq.mm FR PVC insulated 1100 V grade multistrand single core copper cunductor cable as earth continuity wire drawn inside the conduit complete in all respect . 126 Supply and fixing of LED tube light with better suitable for up to 22 watt LED tube light fitting including tube on surface complete in all respect . 127 Supply and fixing of LED Street light fitting having die cast aluminium body and diffuser/ Reflector with driver set suitable for 65 watt. Confirming to IP66 Protection complete in all respect. 128 Supply and fixing of 100 Amp. Four pole change over switch on 40mm X40mm X6mm angle iron frame , including the cost of labour , T&P , painted and other material required for proper completion of the work as per direction and satisfaction of engineer in charge. 129 Supply and fixing of fan sheet of backelite. 130 Supply and fixing of ceilling fan ISI marked 1200mm sweep. 131 Supply and fixing LED Bulb 20 watt. 132 Supply and fixing of exhaust fan 12" dia 133 Supply and fixing of cable Gland AI lugs etc. 134 providing and fixing of single twin bed6"-0"length and2"-6" wide. Bed is made of 19mm thk. Boardfinished with mica, laminates along with one side tables of size 1"-6" X 1"-0" X 1"-6"finished with mica or laminates on both sides 135 providing and fixing of 6"-0 wide and 6"-0" length and 1"-6"height Guest Bed, made of board and finished with mica , laminates, with upholstered 4"-0" ht head board. Two side tables of size 1"-6" X 1"-6" X 1"-6" made of board fixed along the both sides of bed, finished with mica or laminates on both sides drawer fixed with channel and handle and open shelves below 136 providing and fixing of 2"-6" wide and 7"-0" hightwardrobe with 2"-0" depth.wardrobe made up of laminated board with openable shutters finished with laminates, mica pasted on all sideswith handle, and locks on shutter and all drawers inside and shutters fixed with hinges . 137 providing and fixing of tv cabinets 1"- 0" deep and6"-0" length. Made of laminated board finihsed with mica and laminates placed with 3/4" groove wih 6" deep drawers mica pasted on all sidesfixed with s.s 10" channel and handle and lock above it, along with the open shelves. 138 providing and fixing of 10 seater dinning table as perdesign made of board and vinner with natural polishh above it . And dining chairs made of wood with ploished finished and upholstered in good quality fabric , foam of high densityat the back and sitting. 139 Provind and fixing of chairs in guest bedroom made of wood and vineer with natural ploish on it. Finihsed with the upholstered finish at back and sitting along with side table 140 Providing and fixing of Table in Office in 6"-0" length and 2"-6" wide finished with vineer / laminates / glass having 3 drawers on one side andone cupboard on the other side made of 19.00 mm board with 1.0 mm vineer / laminates pasted on all sides , lock on all drawers and all cupboards. vineer / laminates pasted on both sides external & internal, foot rest with table. 141 Providing and fixing of Office chair revolving with moulded foam seat with P.U. arms and P.U. base, with twin wheel casters upholstered in good quality cloth. foam of high density 142 Providing and fixing of staff Table made of 19.00 mm board with laminate 1.0 mm both sides and front size (4"-0" X 2"-6") withh 6" deep one drawers mica pasted on all sidesfixed with s.s 10" channel and handle and lock above it, along with the open shelves for keyboard. 143 Providing and fixing of StaffChair with arms, revolving and P.U. base with twin wheel, casters, upholstered in good quality cloth,foam of high density 144 providing and fixing of 12 Seater Conference table as perdesign made of board and vinner with natural polishh above it . And chairs madewith arms, revolving and P.U. base with twin wheel, casters, upholstered in good quality cloth,foam of high densityat the back and sitting. 145 Providing and fixing of Air Conditioing in guest bedroom and office area including copper & drainage pipes. 146 WIRE FANCINGExcavation in foundation in ordinary soil incl. lift up to 1.5M and lead upto 30m and incl. filling, watering and ramming of excavated earth in to the trenches or in to the space between the building and the sides of foundation trenches or into the plinth and removal & disposa of surplusearth as directed by the Engineer incharge. 147 Providing and laying cement concrete in 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregte 40mm nominal size ) and curing complete .including cost of form work. In Foundation and floors . 148 Providing and laying cement concrete in 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregte 20mm nominal size ) and curing complete .including cost of form work. In Foundation and floors . 149 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarsesand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-incharge (cost of earth works in excavation, concrete works in foundation to be paid separately). 150 Supplying and fixing turn buckles and straining bolts for barbed wire fencing. 151 Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire. 152 Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.67 Ltr/10 sqm including one coat of primer applid @ 2.2 Ltr/10 sqm coat curing and cost of all material, labour, T & P etc. required for proper completion of work for two coat. 153 Cleaning jungle including uprooting of trunks, vegetation, grass, bushes, wood trees and saling of girth upto 30cm measured at a height 1 metre above ground level and removal of rubbish upto a distance of 50 metre outside the periphery of area cleared. 154 UNDER GROUND IRRIGATIONPIPE LINE Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia 155 Providing and fixing 140mm PVC pipe conforming to IS make working pressure 6kg/sqcm including testing labour T&P and all complete fittings . 156 Providing and fixing 140mm Flench with complete fitting with nut , bolt etc. 157 Hi-TECH NURSURYEstablishment of Hi-tech Poly house (44x24=1056sqm) for producing vegetable/fruits planting material for farmers. 158 Shade Net House 40x25=1000 sq mt with all amenities and fixtures. 159 Establishment of HYV Mother plants of fruits crops ( Kinnow, lemon, guava,ber,beal etc.) in 1 acre land at KVK Farm 160 Tools : Tractor mounted 500lts Spray tank HTP power sprayer with 100mts high pressure pipe & spray nozzle 161 Tools : Tractor mounted detachable Augar of 3 feet in length & 1.5 feet in width for orchard/tree plantation in the district. 162 CAMPUS ROADExcavation in foundation in ordinary soil incl. lift up to 1.5M and lead upto 30m and incl. filling, watering and ramming of excavated earth in to the trenches or in to the space between the building and the sides of foundation trenches or into the plinth and removal & disposa of surplusearth as directed by the Engineer incharge. 163 Earth work in filling orfinary Soil (Loam,Clay or sand ) including lift up to 1.50M and lead up to 30M and including filling watering and ramming of excavated earth into the tranches or into the space between the building and the sides of foundation trenches of into the plinth and removal and disposal of surplus earth as directed by the engineer- in - charge up to a distance of 30 M from the foundation tranches . including royalty. 164 Providing and laying in position cement concrete of Specified grade 1:3:6 (1 cement : 3 coarse sand :6 Graded stone aggregate 40 mm nominal size),including the cost of centering, shuttering, finishing. 165 Construction of un-reinforced, plain concrete cement avement thicknessas per design, over a prepared sub base with 43 grade cement or any other typeas pr clause 1501.2.2 M-30 (Grade), course and fine aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film wedges , steel plates including levelling theformwork as per drawing ), spresding the concrete with shvels, rakes, compacted using needle , screed and plate vibrators and finished in continous operation including provision of contraction, expansion, constructionand constructional joints, appliying debonding strips, primer, sealant, dowel bars, near approches to bridge/culvert and construction joints, admixtureas approved, curing of concrete slabs for 14 days, curing compund (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501. 166 Class -150 (Non Modular ) brick work in 1:6 cement and coarse sand mortar in foundation and plinth including supply of all materials , labour and T&P etc. required for proper completion of the work . 167 Providing and laying GSB with graded stone ballast with stone grit size stone ballast with hand ramming watering including all material labour T&P etc. all complete 168 Supply & Laying of precast concrete Blocks (Interlocking tiles) for paving of thickness 60mm to 100mm (Compressive strength not less then 30Mpa as specified in IS:15658) Including 25mm thick local sand base levelling and dressing of surface to required level and slope , filling joints with local sand all complete work as specified in IS 15658:2006 80mm (Rubber molded Grey ). 169 Providing and laying cement concrete in 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregte 20mm nominal size) and curing complete including cost of form work. In Foundation and Floors. 170 15mm cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angels chamfers, and rounded angels not exceeding 80mm in girth and finished even and smmot. 171 SEPTIC TANKExcavation in foundation in ordinary soil incl. lift up to 1.5M and lead upto 30m and incl. filling, watering and ramming of excavated earth in to the trenches or in to the space between the building and the sides of foundation trenches or into the plinth and removal & disposa of surplusearth as directed by the Engineer incharge. 172 Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors. 173 First class brick work in 1:6 cement and coarse sand mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. 174 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 12.5mm nominal size) 175 Reinforced cement concrete in beams, suspended floors, roofs having balconies, shelves, chajjas, bands, staircase and spiral staircase above plinth level upto floor five level including the cost of centering, shuttering, and excluding the cost of reinforcement with 1:1.5:3 ( 1 cement: 1.5 coarse sand : 3 graded stone) in lintel beams 176 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 177 12mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. any additive. (1) 1 cement : 6 fine sand. 178 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 179 G.S.T Extra as per applicable
|
