Tender For Supply Of Steel Furniture. (M-44) in India

Work Detail

Supply Of Steel Furniture. ( M-44 ) Annual Rate Contract For The Supply Of Steel Furniture. , Steel Almirah Door And Shelves Made Of 1Mm Thick And Body Made Of 0.8Mm Thick M.S Sheets Of Size 1980X865x485mm With 4 Shelves Making 5 Compartments And Shall Be Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor.Weight : 62.400 Kg, Variation= + 3% , Steel Almirah Door And Shelves Made Of 1Mm Thick And Body Made Of 0.8Mm Thick M.S Sheets Of Size 1270X765x440 Mm With 3 Shelves Making 4 Compartments Shall Be Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor. Weight: 39.00 Kg, Variation= + 3% , Steel Almirah Door And Shelves Made Of 1Mm Thick And Body Made Of 0.8Mm Thick M.S Sheets Of Size 1980X1010x530mm With 4 Shelves Making 5 Compartment Shall Be Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor Weight : 72.500 Kg, Variation= + 3% , Steel Library Almirah Door Andshelves Made Of 1Mm Thick And Body Made Of 0.8Mm Thick M.S Sheets Of Size 1980X920x485mm Fitted With 4 Shelvesmaking 5 Compartment With Glass Door. Height Of The Foot From Ground Shall Be 100 + / -5 Mm. The Handles Shall Be Of Zinc Base Alloy Casting Conforming To Is 742-1981 ( Re-Affirmed 2003 ) And Glass Sheet Conforming To Is 2835-1987 ( Re-Affirmed 2004 ) . Steel Library Almirah Shall Be Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor. Weight : 73.700 Kg, Variation= + 3% , Book Case Made Out Of 1 Mm Thick M.S Sheets With 4 Shelves Andhaving 4 Compartments Each Closed By And Individual Locking Arrangementby A Glass Line Shutters Which Should Be Pushed In Each Of The Compartment Be Fitted With Two Metal Handles Size 1675X840x305mm. Height Of The Foot From Ground Shall Be 100 + / -5 Mm. The Handles Shall Be Of Zinc Base Alloy Casting Conforming To Is 742-1981 ( Re-Affirmed 2003 ) And Glass Sheet Conforming To Is 2835-1987 ( Re-Affirmed 2004 ) .Steel Book Cases Shall Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor. Weight : 46.500 Kg ( Steel Weight: 37.00 Kg ) , Variation= + 3% , Adjustable Record Racks Of Different Sizes Made Of Slotted Angle So As To Adjust Shelves Of Size 915X380 Which Should Be Made Of 0.80Mm Thick C.R.C Sheet Duly Painted With Synthetic Enamel Paint. Slotted Angle Size 35Mmx35mm And Distance Between Shelves 375 Mm ( Rate Shall Be Quoted Per Shelf ) . Per Shelf : 2.500 Kg. 3 Shelf Assembling 12.00 Kg, Variation= + 3% , Office Table Size: 900X610x750mm Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mm Painted With Synthetic Enamel Paint With One Side Drawer With A Locking Device, In Mild Steelsq. Pipe Of Section 25X25x1.25Mm. The Drawers Of Cup Board Made Of 0.8Mm Thick Sheet.Table Top Should Be Of 18 Mm Thick Pre-Laminated Board / Mdf. Weight : 15.200 Kg ( Frame 9.00Kg And Board 6.200 Kg ) , Variation= + 3% , Executive Table Size: 1800X900x760mm Painted With Synthetic Enamel Paint With 3 Drawers On One Side & Cup Boardon The Other. The Drawers Of Cup Board Made Of 0.8Mm Thick Sheet.Table Top Should Be Of 18 Mm Thick Pre-Laminated Board / Mdf.Weight : 67.00Kg ( Frame 40.900 Kg ) , Variation= + 3% , Executive Table Size: 1500X900x760mm Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mmpainted With Synthetic Enamel Paintwith 3 Drawers On One Side & Cup Boardon The Other. The Drawers Of Cup Board Made Of 0.8Mm Thick Sheet. Table Top Should Be Of 18 Mm Thick Pre-Laminated Board / Mdf.Weight: 61.00 Kg ( Frame: 38.900Kg ) , Variation= + 3% , Stool Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mmpainted With Synthetic Enamel Paintwith Cushioned Seat Of Standard Size. Cushion Should Be Made Offlexible Polyurethane Foam Having Density Of 28 Kg / M³ And Indentation Hardness Shall Be 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. The Bottom Legs Of The Bed Should Be Provided With Caps Made Of Metal, Plastic Or Rubber Which Will Not Mark The Floor And Is Resistant To Sliding.Weight : 4.700Kg ( Frame: 3.100 Kg ) , Variation= + 3% , Stool Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mmpainted With Synthetic Enamel Paintwith 12Mm Thick Ply At The Top Of Standard Size.Weight: 4.600 Kg Iron: 3.00 Kg, Variation= + 3% , Three Seated Sofa Set Having Seat Size Of457x457 Mm Made Out Of 50 Mm X 25Mmx18 Gauge Rectangular Pipe Painted With Synthetic Enamel Paint Duly Finished In Teak Colour / Walnut Shade. Bottom Legs Should Be Closed By Welding With Crc Sheet And Fitted With Synthetic Flooring.Seat Cushion Should Be Made Of Flexible Polyurethane Foam Of Seat Size 457X457 Mm And 75Mm Thick Having Density Of 40 Kg / M³ And Indentation Hardness 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. The Seat Height Should Be 406 Mm And Totalheight At The Back Should Be 760 Mm. Bottom Of Legs Should Be Closed By Welding With Crc Sheet And Fitted With Synthetic Flooring. Steel Frame: 24.00 Kg, Variation= + 3% , -Do- But Single Seated.Seat Cushion Should Be Made Of Flexible Polyurethane Foam Of Seat Size 457X457 Mm And 75Mm Thick Having Density Of 40 Kg / M³ And Indentation Hardness 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. The Seat Height Should Be 406 Mm And Totalheight At The Back Should Be 760 Mm. Bottom Of Legs Should Be Closed By Welding With Crc Sheet And Fitted With Synthetic Flooring.Weight: 12.00 Kg, Variation= + 3% , Desk Made Of Mild Steel Sq. Pipe Of Section 25X25x1.25Mm Painted With Synthetic Enamel Paint Having Seat Of 18Mmmdf Board Duly Fitted With Shelf For Keeping Books Made Out Of 18 Mm Mdf Board ( Front, Sides & Top ) , Single Seater. Weight: 14.00 Kg ( Frame: 7.00 Kg ) , Variation= + 3% , Dual Desk Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mm Painted With Synthetic Enamel Paint Of Length 900 Mm, Width 840 Mm Seat At Height 450 Mm Having Width Of 300 Mm Gap Between Shelf For Keeping Books And Seat Shall Be 200 Mm. Height Of Top From Ground 775 Mm With Slope Of 25 Mm Towards Seat. Shelf Shall Rest At Height 580 Mm Made Out Of 18 Mm Mdf Board ( Front, Sides & Top ) Fitted With Bolts And Nuts At Minimum Four Points.Weight : 21.00 Kg ( Frame: 8.00 Kg ) , Variation= + 3% , Desk Made Of 25Mmx18 Gauge Pipe Painted With Synthetic Enamel Paint Fitted With Pre-Laminated Mdf Fitted With Bolts And Nuts At Minimum Four Points, Double Seater With Length 750 Mm, Height 600 Mm, Seat Height 300 Mm, Back 300 Mm, Seat Width 250 Mm And Desk Top 300 Mm Fitted With Bolts And Nuts At Minimum Four Points. Gap Between Shelf & Seat Will Be 200 Mm With Slope Of 25 Mm Towards Seat. Seat Shall Be Made Out Of 18 Mm Mdf Board ( Front, Sides & Top ) Fitted With Bolts And Nuts At Minimum Four Points. Weight: 18.840 Kg ( Steel Frame: 9.00 Kg ) , Variation= + 3% , Examination Table For Hospital Size1800x600x825mm Made Of 25Mmx18 Gauge Sq. Pipe Painted With Synthetic Enamel Paint And With Block Board19mm Fitted With Bolts And Nuts At Minimum Four Points. Weight : 24.400 Kg ( Frame: 10.800 Kg ) , Variation= + 3% , Hostel Bed Of 1800Mmx900mmx450 Mm ( Lengthxwidthxheight ) Made Of 50X25 Mm 18 Gauge Rectangular Pipe Painted With Synthetic Enamel Paint And With 12 Mm Ply Fitted With Bolts And Nuts At Minimum Four Points.Weight: 29.00 Kg ( Frame: 14.500 Kg ) , Variation= + 3% , Desk Double Seater Made Of 25Mmx18 Gauge Sq. Pipe Painted With Synthetic Enamel Paint And Fitted With 18 Mm Block Board With Sunmica Top Fitted With Bolts And Nuts At Minimum Four Points Without Box And Back. Size: 900 Mm Length X825 Mm Total Width X 750 Mm Height. Width Of Seat Should Be 300 Mm Also Made Out Of 18 Mm Board With Sunmica Top Or 18 Mm Laminated Board Also Fitted With Bolts And Nuts At Four Points.Gap Between Bench & Seat 225 Mm. Weight : 18.160 Kg ( Steel Frame: 11.300 Kg ) , Variation= + 3% , Lecture Stand 18Mm Mdf Particle Laminated Board With Screw Fitting. Ht. 48" X 44" Slope 4" Box 4" Top 24"X18" Base 44" X 18" Three Side Covered In Mdf Board One Side Open Top Bedding 2"X1" Slope All Edge Weeding Polishing With Good Finishing. , Single Table And Chairs Made Of Aluminium / Steel Round Pipe. Chair Seat At Height 343 Mm Having Width Of 300 Mm. Gap Between Shelf For Keeping Books And Seat Shall Be 155 Mm. Height Of Top From Ground 510 Mm With Slop Of 25 Mm Towards Seat. Shelf Shall Rest At Height 383 Mm, Made Up Of Mdf Board Fitted With Bolts And Nuts At Minimum Four Points. Max. Angle Of Chair Seat 4 Degree And Angle Between Seat And Backrest 95 To 100 Degrees , Dual Desk With Separate Bench Of Length 770 Mm Width 500 Mm Height Of Top From Ground 590 Mm. Seat At Height 368 Mm Having Width Of 320 Mm. Gap Between Shelf For Keeping Book And Seat Shall Be 165 Mm. Height Of Top From Ground 590 Mm With Slop Of 25 Mm Towards Seat. Shelf Shall Rest At Height 420 Mm Made Of Mdf Board Fitted With Bolts And Nuts At Minimum Four Points. Max. Angle Of Chair Seat 4 Degree And Angle Between Seat And Backrest 95 To 100 Degrees , Dual Desk With Separate Bench Of Length 900 Mm Width 500 Mm Height Of Top From Ground 775 Mm. Seat At Height 450 Mm Having Width Of 320 Mm. Gap Between Shelf For Keeping Book And Seat Shall Be 200 Mm. Height Of Top From Ground 775 Mm With Slop Of 25 Mm Towards Seat. Shelf Shall Rest At Height 580 Mm Made Of Mdf Board Fitted With Bolts And Nuts At Minimum Four Points. Max. Angle Of Chair Seat 4 Degree And Angle Between Seat And Backrest 95 To 100 Degrees , Waste Paper Basket Square Type Made Out Of 1Mm Mild Steel Sheet Duly Painted With Synthetic Enamel Paint Havingheight 305Mm, Sq Top 280Mm, Sq. Bottom 200Mm. , Steel Locker Cabinet Made Out Of 0.80 Mm Thick M.S Sheets Of Size 1980X920x440mm Fitted With 8 Lockers. Locker Cabinet Shall Be Painted With Synthetic Enamel Paint On Inside And Spray Hammer Tone Paint From Outside In Silver Ash / Olive Green Oras Requested By The Indentor. , -Do- With 6 Lockers. , -Do- Of Size 1270X765x440mm Fitted With 6 Lockers. , Steel Record Box Of Size 750X500x500mm Made Of 1.25Mm Thick Ms Sheet. , Revolving Metal Chair With High Back Rubberised Seat Of Size 360X360mm And Back 725X475 Mm Having Castor Unitwith Hydraulic System With5 Numbers Pvc Wheels. Seat / Back Cushion Should Be Made Offlexible Polyurethane Foam Having Density Of 28 Kg / M³ And Indentation Hardness Shall Be 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. , -Do-With Push Back Spring Having Double Action I.E. Fixed And Pushed Back. Seatshould Be Fitted With Shoulder Action. , Metal Chairwithout Arm-Rest With Cushioned Seat In Mild Steel Sq. Pipe Of Section 25X25x1.25Mm In Standard Size. Seat Cushion Should Be Made Offlexible Polyurethane Foam Having Density Of 28 Kg / M³ And Indentation Hardness Shall Be 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. , Office Metal Chair With Arm-Rest Canned Seat & Back In Mild Steel Sq. Pipe Of Section 25X25x1.25Mm In Standard Size. The Wooden Arms & Steel Tubes Shall Be Screwed At Three Places. , Office Writing Table Of Size 1200Mmx610mmx760mm Made Of Mild Steel Sq. Pipe Of Section 25X25x1.25Mm Painted With Synthetic Enamel Paint With 1 Drawer On The Right Side With A Locking Device. The Drawers Of Cup Board Made Of 0.8Mm Thick Sheet. Table Top Should Be Of 18 Mm Thick Pre-Laminated Board / Mdf. , Office Writing Tables 1200Mmx610mmx 760Mm Made Of Mild Steel Sq. Pipe Of Section 25X25x1.25Mm Painted With Synthetic Enamel Paint With 3 Drawers On The Right Side With Locking Device In Mild Steel Sq. Pipe Of Section 25X25x1.25 Mm. The Drawers Of Cup Board Made Of 0.8Mm Thick Sheet. Table Top Should Be Of 18 Mm Thick Pre-Laminated Board / Mdf. , Composite Office Table For Computer Of Sizeh750xw1350xl750mm Made Of Mild Steelsq. Pipe Of Section 25X25x1.25Mmpainted With Synthetic Enamel Paint. The Base Pipe Should Be Of Size 25X50mm Of 18 Gauge Thickness. The Data Entry Unit, Electronic Typewriter Of Key Board Which Can Be Adjusted Independently By Actuating A Simple, Convenient Knob So That Execution Of These Adjustments Can Be Carried Out With The System In Place. The Top, Keyboard Tray And Drawer Madeof Mdf Board. , Revolving Computer Chairs With Arm-Rest Cushioned Seat & Back And Hydraulic System. Seat / Back / Handles Should Be Of Chrome / Pu Base. Seat Size 400Mmx400 Mm, Back Size 400X375 Mm. Cushion Should Be Made Offlexible Polyurethane Foam Having Density Of 28 Kg / M³ And Indentation Hardness Shall Be 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. , Steel Police Pattern Bed Of Size:1800X900x450mm Made Out Of 50 Mmx25mm Rectangular Pipe 18 Gauge Painted With Synthetic Enamel Paint ( Without Ply & Niwar ) . Bottom Of Legs Should Be Closed By Welding With Crc Sheet. , -Do- But With 12 Mm Ply / Niwar. , Office Bench Of Size 1500X450x900mm With Arm-Rest In Teak Board Made In 25Mm X 18 Gauge Sq. Pipe Painted With Synthetic Enamel Paint. , Conference Chair With Seat Size Of 457X457 Mm Made Of Rectangular Pipe 35X25mmx18 Gauge Rectangular Pipe Painted With Synthetic Enamel Paint Duly Finished In Teak Colour / Walnut Shade Withcushioned Seatmade Of Flexible Polyurethane Foam Of Seat Size 457X457 Mm And 50Mm Thick Having Density Of 32 Kg / M³ And Indentation Hardness 18 To 25 Kgf Covered With Best Quality Leather Foam Or Furnishing Cloth. The Seat Height Should Be 406 Mm And Totalheight At The Back Should Be 760 Mm. The Back Rest Should Have Two Cross Supportsbottom Of Legs Should Be Closed By Welding With Crc Sheet And Fitted With Synthetic Flooring. , Hostel Bed Of 1800Mmx900mmx450 Mm ( Lengthxwidthxheight ) Made Of 50X25 Mm 18 Gauge Rectangular Pipe Painted With Synthetic Enamel Paint And With 12 Mm Ply Fitted With Bolts And Nuts At Minimum Four Points. , Cocoon Auction Platform : Body Structure Made Up Of Angle Iron Of 40 X 40 X 4 Mm And Top & Bottom Made Up Of Angle Iron 32 X 32 X 3 Mm With Perforated Iron Sheet 4 X 6 Feet Size With Partition In The Centre.

Contact Information