|
Rate List Quotation Notification for Below non sr Items.-fm Radio and Related Accessories-1Supply, installation, testing and commissioning of outdoor Omni-directional garden speaker fitted with two numbers of wide response and water resistant polypropylene cone speakers and strong cylindrical aluminum alloy housing for various outdoor applications. The speaker must conform to weather-resistant protection norms with an input power rating of 40W RMS operating on a 100 volt line system with accessible external color-coded wire power tapings of 40, 20, 10, and 5 watts. The system shall provide a sound pressure level of 88 dB (1W/1m), a frequency response range of 160 Hz to 16,000 Hz, and physical dimensions measuring approximately 185 mm in diameter by 765 mm in height. Scope includes providing all necessary heavy-duty speaker mounting hardware along with precision mounting templates to be firmly grouted directly into the concrete foundation using welded anchor bolts as required to securely fix and stabilize the garden speaker column against high wind loads and outdoor exposure. Make: Ahuja Model GS-6401T or approved equivalent2Supply, installation, testing and commissioning of high-wattage single-channel public address booster power amplifier operating on Class H technology for optimum thermal efficiency. The amplifier shall deliver a power output of 2500W RMS at 10% THD, 2300W RMS at 5% THD, and a maximum peak output of 3000W, featuring a flat frequency response of 50 Hz to 15,000 Hz (+/-3dB) with a signal-to-noise ratio of 75dB. Input channels must include a switchable balanced/unbalanced line input supporting both 200m V and IV sensitivities via XLR and 6.3mm stereo phone jacks, alongside a specialized 100V input terminal strip to allow dirett looping from another amplifier output. Output configurations must accommodate low impedance speaker loads at 2 Ohms and 4 Ohms, as well as distributed high-voltage lines at 70V and 100V via heavy-duty terminal strips. The system must feature comprehensive built-in protection circuitry safeguarding against overload, output short-circuits, over-temperature conditions, and AC mains over-voltage anomalies typical of temporary generator setups. Front panel controls must feature cut/boost type tone adjustments providing +/-10dB at 100Hz for Bass and +/-10dB at 10kHz for Treble, accompanied by a rear Box Speaker / Driver Unit selector switch that automatically rolls off sub-low frequencies when toggled to protect driver unit diaphragms. The unit shall draw a maximum AC power consumption of 3400VA at 220-240V 50/60Hz, measure 520mm in width by 185mm in height by 595mm in depth, and weigh approximately 38.50 kg. Make: Ahuja Model SPA-25000 or approved equivalent.Supply, installation, testing and commissioning of a compact, professional-grade 6-channel public address audio mixing console suitable for live performances and commercial PA setups. The mixer must feature four independent mono microphone/line level input channels and one dedicated stereo input channel, all utilizing standard 6.3 mm (1/4-inch) stereo jack sockets capable of accepting balanced or unbalanced configurations. Each input channel must be equipped with an independent rotary gain control for sensitivity adjustments, an active 2-band equalization system consisting of individual bass and treble controls, and a separate FX/effects level routing control. The mixer shall include a built-in digital effects processor offering dedicated delay, repeat, and level parameters to generate customized echo and reverb effects, Master section controls must feature separate master level volume knobs accompanied by individual signal and peak/clip LED level indicators to monitor excessive input levels and avoid audio distortion. Main audio outputs must provide line-level left and right channel feeds distributed through dual 6.3 mm (1/4-inch) stereo jack sockets to facilitate balanced connections to booster or zone amplifiers. The system must operate reliably on a standard 220-240V AC 50/60Hz power supply and feature a lightweight, portable housing design. Make: Ahuja Model FMX-106 or approved equivalent. (Note: If an onboard MP3 digital player with Bluetooth streaming, USB playback, and recording functionality is required for your installation, the upgraded modelvariant FMX-106DP must be specified) Fabricating, Supplying and errection of Garden speaker protective enclosure of size H 1.55mmx1.30.50mmx830.50mm fabricated out of MS 11/8 L angle and 1 weld mesh with bolts, washers, nuts & etc; and painted with 2 coats of red oxide and then two coats of green any approved enamel paint.Decorative Lights AMC, Solar Street Lights and Related AccessoriComprehensive Annual Maintenance Contract (CAMC) services for the specialized architectural multicolor LED decorative light tower. Detailed Scope of Work: Preventive Maintenance: Conducting monthly routine visual inspections, data continuity tracing, and hardware checks. Bi-monthly professional dust/debris cleaning of polymer diffuser channels and ventilated driver enclosures. Quarterly insulation testing (megger checks) and grounding path audits. Comprehensive Spares Support: Complete ownership, supply, and installation of original specification matching spare materials to replace failed items at zero extra cost. Includes outdoor-grade programmable RGB LED pixel strips, IP67 Constant Voltage power supplies (SMPS), SPI multi-port pixel controllers, DMX decoders, signal boosters, data cables, and distribution panel elements (breakers, surge protection devices, astronomical timers). Breakdown Support & Logistics: Execution of on-call breakdown troubleshooting to fix power trips, short circuits, or animation glitches within a strict 24-to-48-hour SLA resolution window. Provisioning of all specialized high-access infrastructure including hydraulic boom lifts, cherry pickers, or mobile scaffolding towers required to safely access upper elevated rings. Terms & Deliverables: Rates must include all logistics, labor, transport, high-access plant rental, tools, and testing equipment. Payment will be disbursed in four (4) equal quarterly installments of 25% each, subject to the submission of certified monthly site inspection logs and a clear performance certificate from the5Operation and Maintenance of LED RGBW LED flood light covers preventive and corrective maintenance of the 100W RGBW LED floodlight to ensure reliable performance, optimum illumination, and extended service life. Services include periodic inspection, cleaning of the luminaire and lens, checking electrical connections, testing the LED light source and driver, verifying the waterproof seals and mounting hardware, and replacing defective components as required under the terms of the contract. Regular maintenance helps maintain consistent lighting performance, minimizes downtime, and ensures safe and efficient operation in outdoor architectural lighting applications,Comprehensive Annual Maintenance for Musical Dancing Fountain: Providing an all Inclusive, one-year turnkey Comprehensive Annual Maintenance Contract (CAMC) for the complete musical dancing fountain system, including all mechanical, hydraulic, electrical, lighting, automation, and control components. The scope shall include routine preventive maintenance, periodic cleaning, inspection, testing, calibration, and performance optimization of pumps, nozzles, valves, underwater RGB/RGBW LED lights, electrical panels, PLC/DMX controllers, VEDs, audio synchronization system, and associated equipment. The contractor shall provide comprehensive breakdown maintenance, replacement of all defective components and original specification spare parts at no additional cost, maintain water quality and filtration systems, and ensure uninterrupted operation of the fountain. The CAMC shall include all labor, consumables, tools, testing Instruments, transportation, safety equipment, and any specialized access equipmentPage 2 of 5required to complete the maintenance, ensuring reliable performance and restoration of faults within the stipulated service response period Operation and Maintenance of 3.0 m high Decorative Aluminum Pole Model(Square, Diamond, ALTIES, PICTOR, AURA, XENON, GIRAFFEE, TRIO or any equalent) complete with 60 W LED luminaires and 20 W LED strip light, including periodic inspection, cleaning, testing, preventive maintenance, inspection of MCB, terminal blocks, internal wiring, cable entry, earthling connections, and control gear to ensure safe and reliable operation. The scope shall include replacement of defective LED drivers, LED strip lights, connectors, wiring, MCBs, terminal blocks, and other electrical accessories, rectification of faults such as non-functioning luminaires, strip lights, loose connections, water ingress, flickering, and electrical failures; and carrying out all routine and breakdown maintenance complete in all respects as directed by the Engineer-in-Charge.Operation and Maintenance of Sculpture Decorative LED luminaires including periodie inspection, cleaning, testing, preventive maintenance, inspection of MCB, terminal blocks, internal wiring, cable entry, earthling connections, and control gear to ensure safe and reliable operation. The scope shall include replacement of defective LED drivers, LED strip lights, connectors, wiring, MCBs, terminal blocks, and other electrical accessories; rectification of faults such as non-functioning luminaires, strip lights, loose connections, water ingress, flickering, and electrical failures; and carrying out all routine and breakdown maintenance complete in all respects as directed by the Engineer-in-Charge,Supply and installations of IP66, 60 watts LED Solar street light with 5 Mtrs long MS pole as detailed specification Housing ABS Anti-UV Plastic Housing with lance or reflector should not be less than 640*250*70mm, Solar Panel 6V 15W High-efficiency polysilicon (Conversion rate 13%) tempered glass laminated, Battery Lithium iron phosphate battery (15Ah/3.2V)Over Charge Protection Deep Discharge protection LED Chip 4000-4600lm BEAM Angle 120°Control panel Get dark will turn on, under sunshine will charge energy, Mir Mild Steel Pole of dimension Bottom 2mtr Length 76mm OD and Top 3mtr 60mm OD With 3mm thickness, Imtr 42mm OD Single arm 15 deg welded or bracket to the pole. Base Plate size 220 mm x 220 mm welded at the bottom of the pole Painted with two coats of anticorrosive red oxide and Graffiti Grey suitable for Solar Street Light, includes digging of 1 mir length and 0.30 mtr dia, 1:2:4 bottom concert and 0.3 mtrs above ground level coping complete.Operation and Maintenance of 60 W IP66 LED Solar Street Light with 5.0 m MS Pole, including periodic inspection, cleaning of the solar panel and luminaire, testing of battery, LED module, charge controller, wiring and electrical connections, preventive maintenance, inspection of pole, foundation and mounting hardware, replacement of defective LED driver, battery, charge controller, LED module, wiring, connectors and other electrical accessories, rectification of faults including low illumination, charging failure, battery failure, loose connections, water ingress and structural defects, complete with routine and breakdown maintenance, ensuring satisfactory operation of the system as directed by the Engineer-in-Charge.Electrical Crematorium Related AccessoriesSupplying & fixing of Coil Holding Refractory Bricks suitable for vertical coil insertion system electrical crematorium furnace conforms to 18-2042. The bulk density of the brick will be max of 2.20gm/cm2 and operating temperature of 6500c to 8500c and max temperature of 13000c. The size of the bricks 115 x 115 x300mm including loading. Unloading and transportation to work site.Supplying & fixing of Insulation Refractory STANDARD bricks suitable for crematorium furnace having the bulk density of max of 0.60gm/cm2 and maximum working temperature of 13000c, the size of brick 75 x 115 x 225mm including loading and unloading to work siteSupplying & fixing of STD IS & Alumina Refractory bricks suitable for electrical crematorium furnace having maximum working temperature of 13000e. The size bricks 75 115 x 225mm including loading, Unloading and transportation to work site,Supplying & fixing of STD IS 6 Alumina Refractory bricks suitable for electrical Crematorium furnace having maximum working temperature of 13000c. The size bricks 75 115 x 225mm including loading, Unloading and transportation to work site.Supplying & fixing IS 8 Alumina Refractory Side Arch Bricks suitable for electrical rematorium furnace having required mechanical strength and maximum working emperature of 13000c. The size bricks- 230 x 115 x 75/65mm including loading, unloading und transportation to work site.Supplying & fixing of Refractory Slabo (MCL) suitable for clectrical crematorium fir having the required mechanical strength and chenile composition as per 15 2042 and 15 1528, max working temperature up le 13000C. The size of the bricks-115 x300 x 450mm including loading and unloading, tromportation to work siteSupplying & fixing Body Laying with 70% sluminum Molded Refractory tricks (MCL) suitable for electrical crematorium furnace having the required mechanical strength and chemical composition as per 15-2042 and 15-1528 max working temperature up to 13000 The bricka-150 x 300 x 600mm including loading, unloading and transportation to work siteSupplying of refractory cement finc ACC-50 (25 kg/bag) for casting refractory bricks)Supplying of refractory cement FIRECRETE saper (25 kg/bag) for casting refractory bricksSupplying & flosing of Refractory comest while heat K ACC make for casting refractory bricks, 25 kgs bag:Supplying of Acoustic Set Thermous Liquid Winder suitable for citing refractory bricks 40 kgs hucket.Supplying & fising of FIBER blank kit 96 grade suitable for electrical crematorium furnace heal insulation-7300 x 610 x 25mm.Supplying & fixing of FIBER blank kit 128 grade suitable for electrical crematorium furnace heat insulation-7300 x 610 x 25mmSupplying & fixing of SS stud of size 304 x 250 x 10mm with locking washer far dout work()Supplying & fixing of FIRE clay cerpent (40 kg/bag) for curting refractory bricks()Supplying & fixing of Refractory Slats 15- high aluminum suitable for electrical crematorium farmace having the required mechanical strength and chemical composition an per 15 2042 and 15-1528, nix working temperature up to 13000s. The size of bricks-100 300 x 600mm including loading and unloading, transportation to work siteSupplying & fixing of 3.5 KW Heating colls made out of 5.8mm thick APM wire, heating Zone should be 950mm length, Eind terminal rod $5 304 grade 10mm dia 550mm length suitable for vertical mounting system in electrical farmace including porcelain beeds spacers supporting rods complete including loading, unloading and trareportation to workSupplying & Fixing of Coil connecting to used to coper lat 25X4 mmSupplying & fixing of Epoxy of Epoxy insalators (bus har ing2) Furnace main door work frost sheet replacement 5 mm thickness, guiding wheel (4 Non) with shalt including bearing replacement and mechanism servicingProviding servicing, repairing and overhesling of existing body charging trolley complete.() Centrifugal belt drives 50mm 85310 Shaft heavy duty 2Nos ball boaring.Supply & erection of 1/2HP 3Phaw 50Hz, 1440RPM large mounting motor with gear op 10RPM with grouting frame, complete including loading, unloading and transportation to work site spare()SS Fabrication 2 mm thick, 500 mm dis with flange. (blower to Chimney connecting pipe)SS Fabrication 2 mm thick, 250 min dia with large. (blower to Chimney exhausting pipe)SS fabrication 2 min thick, 300 mm die with flange. (by-paas lining work)Supply and replacement of Sricke exhaust motor fan shah fabricated out of 55310-dia 50mm x 780mm length with balancing impler 2nos kay slot of 10 x 10mm with computer balancing impler-380mm dia, 160mm width, 3mm sheet fabricated(88304)Supply and fixing of VERTICAL, heating element suitable to operate on 220 volts 50Hz (4.5 KW capacity of heating clement) element shall be made out of 8 SWG 25mm dia mrm pich uxal length 3100 mm superior quality nichrome wire coll and shall be capped with fiberglass tube. New element shall be fixed in furnace heating slots using necessary bbour coroumable and terminated with end bolts etc completeSupply and fixing of VERTICAL, furnace coil holding bricks (240 X 300 X 80mm) made out of refractory material to with stand a temperature of 1000 C using required refractory cement and other binding material to form into required shape (as per BIS-8) completeSupply & crection 2HP 3Phase, 50Hz, 1440 RPM induction flange moumed water pump for Scrubber, Inlet 2 inch, outlet I and off inch inch42Supply & erection of IHP single phase 50Hz water pump (open well Submersible pump set)()43Supply & erection of Smoke exhaust motor 7.5 Hp 3 phase, 50Hz, 1500rpm, induction motor, with table lock pully 180 dia, 2 Nos grove, MAKE ABB/ Kirloskar /Suguna or Equalent44Supply & erection of SS310 pipe Thermocouple 19 mmOD & 700mm length, simplex45Supply & erection of 2 wire Temperature controller range 0 to 1200.c of size 99 x 99MM.46Providing door lifting mechanism set for manually operating made out by 2 bearings 30mm dia and 50mm dia bore shaft and 40 x40x100mm shifting block with handle and mounting bracket47Supply & erection of 22211CK bearing (for exhaust motor )()48Supply & erection of 311H sleeve (adapter)()49Supply & erection of B-58 belt()CCTV AMC Related Accessories50Annual maintenance/Servicing of 4/8/16 Channel DVR51Annual maintenance/Servicing of Hard Disk Surveillance 1 TB/2TB/4 TB-Seagate/WD52Annual maintenance/Servicing of NVR 4 Channel/8 Channel/16 Channel53Annual maintenance/Servicing of IP Network 2 MP/4MP/6MP Bullet or Dome Camera with replacement of BNC/DC Pins Make: Hikvision/CP Plus54Supply and fixing of 16 port 10/100/1000 MBPS POE Switch Make: TP link/ D-link/Secure eye55Supply and fixing of 8 Channel NVR with VGA/HDMI out 2 USB port, RJ 45 Connectivity, Audio in/out UP to 6 MP Support Make: Hikvision/CP Plus56supply and fixing of 16 channel NVR with VGA/HDMI out 2 USB port, RJ 45 Connectivity, Audio in/out UP to 6 MP Support Make: Hikvision/CP Plus57Annual maintenance/Servicing/replacement of Power Supply for Camera 5 Amps/12V58Annual maintenance / Servicing/ replacement of Power Supply for Power Supply for Camera & Amps/12V
|
