|
Bids Are invited for Custom Bid For Services - Increasing Capacity Of 100Kva To 250Kva Dt And Erection Of 33 11 Kv Line Strengthening Work On Semi Turnkey Basis In Business Plan 2026 27 Under The Area Of Edd Fatehabad Agra - (Part-A) Supply & Erection Providing & Fixing Of 11Kv X Arm Cl , Providing & Fixing Of 33Kv X Arm Cl , Providing & Fixing Of Stone Pad , Providing & Fixing Of Cl With Nut & Bolt , Providing & Fixing Of 33Kv F Bracket , Providing & Fixing Of 11Kv F Bracket , Providing & Fixing Of F Cl , Providing & Fixing Of Ms Angle , Providing & Fixing Of Hdpe Pipe , Providing & Fixing Of I Hook , Providing & Fixing Of Suspencion Cl With Eye Hook , Providing & Fixing Of 33Kv Pvc Pipe , Providing & Fixing Of Dropper Channel , Providing & Fixing Of Pg Cl , Providing & Fixing Of 11 Kv Top Channel , Providing & Fixing Of 33 Kv Top Channel , Providing & Fixing Of Shakel Insulator , Providing & Fixing Of T Off Channel , Providing & Fixing Of T- Off Channel With Cl , Providing & Fixing Of Lt Cl For Pcc , Providing & Fixing Of Number Plate , Providing & Fixing Of Gaurding Cl , Providing & Fixing Of Danger Bourd With Nut Bolt , Providing & Fixing Of Gaurding Angle Holding Cl , Providing & Fixing Of Nut & Bolt , Providing & Fixing Of Piercing Connector , Providing & Fixing Of Db Cl , Providing & Fixing Of Dead & Cl , Providing & Fixing Of Holding Cl For Fuse Set , Providing & Fixing Of Lt Lug 250/400/630 Etc , Providing & Installation Of Henley Type Tailless Unit Protection Cubical Panel 500 A 650 V For 250 Kva Dt , Providing & Fixing Of Ms Channel , Providing & Fixing Of Boot &Sleve , Providing & Fixing Of Gaurding Angle , (Part-B) Carriage & Erection Carriage Of Pcc Pole 8.5 Mtr. Long. From Electricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work..(Distance 00-50Kms.) , Carriage Of Pcc Pole 11 Mtr. Long. From Electricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work..(Distance 00-50Kms.) , Carriage Of St Pole 11/13 Mtr. Long. From Electricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work..(Distance 00-50Kms.) , Carriage Of 250 Kva T/F Fromelectricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work..(Distance 00-50Kms.) , Carriage Of 63 Kva T/F Fromelectricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work..(Distance 00-50Kms.) , Cartiage Of 33Kv /11Kv Xlpe Cable 3*300 Sqmm , 11Kv Xlpe Cable 3X185sqmm , Lt Xlpe Cable 3.5*70Sqmm, Lt Xlpe Cable 3.5 Core 250/400/630Sqmm (1070Mtr) Lt Xlpe Single Core Cable 250/400/630Sqmm (744Mtr) From Electricity Store Centretajganj Agra To Work Of Site Through Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work.(Distance 00-50Kms.) , Carriage Of Following Material From Electricity Store Centretajganj Agra To Dump Site Through The Kacha And Pakka Road Including The Work Of Its Loading And Unloading At The Respective Ends Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work.(Distance 00-50 Kms.) Abc 3*50/120Sqmm (5305Mtr) 33/11 Kv X Arm V Type (1011 Nos), 33/11Kv Disc Insulator With Fitting (394 Nos) 11Kv Pin Insulator (3019 Nos), Stay Set (251 Nos ) Earthing Complete (1107 Nos), Weasal Conductor (31932 Mtr) Rabbit Conductor (3100 Mtr) Gaurding Wire (2154 Kg), Jointing Kit 3*185 Indoor/Outdoor (6 Nos), Jointing Kit 3.5*70 (4 Nos), 33/11Kv Jointing Kit 3*300 (6 Nos), 11Kv Do Fuse Set (25 Nos), Distribution Box (141Nos) Barbed Wire Gi (30Kg) , Cable Box 3*300 Incoming/Outgoing/ Straight Through (4 Nos), And Other Meterials As Per Package , Erection And Grouting Of Single Pole 8.5 Mtr. Long Pcc Poles In 1:2:4 Ratio (Cement, Sand And Bricks Balast) Including Fixing Of All Accessories Alongwith Stone Pad As Per Respo Norms Labour, T &P And Carrier, Grouting Material Etc. Required For Proper Completion Of Work Shall Be Done By The Contractor At His Own Cost. , Erection And Grouting Of Double Pole 8.5 Mtr. Long Pcc Pole In 1:2:4 Ratio (Cement, Sand And Bricks Balast) Including Fixing Of All Accessories Alongwith Stone Pad As Per Respo Norms Labour, T &P And Carrier, Grouting Material Etc. Required For Proper Completion Of Work Shall Be Done By The Contractor At His Own Cost. , Erection And Grouting Of 11 Mtr. Long Pcc Pole In 1:2:4 Ratio (Cement, Sand And Bricks Balast) Including Fixing Of All Accessories Alongwith Stone Pad As Per Respo Norms Labour, T &P And Carrier, Grouting Material Etc. Required For Proper Completion Of Work Shall Be Done By The Contractor At His Own Cost. , Erection And Grouting Of St Pole 11/13 Mtr. Long Single In 1:2:4 Ratio (Cement, Sand And Bricks Balast) Including Fixing Of All Accessories Alongwith Stone Pad As Per Respo Norms.Labour, T &P And Carrier, Grouting Material Etc. Required For Proper Completion Of Work Shall Be Done By The Contractor At His Own Cost. , Construction Of Plinth For 250 Kva Transformer Of Size 6X6x3.6 Above The Ground Lable And 1 Feet Below The Ground. At The Bottom There Shall Be Cc Pad Of Brick Ballast Of Size 5X5x3 Thick In Ratio 1:3:6 [Cement, Sand And Brick Ballast]. The First Class Brick Wall Work Shall Be 9 Thick In Ratio 1:4 [Cement And Sand]. The Hollow Portion Among The Wall Shall Be Filled Up With The Brick Ballast. On The Top Of The Wall Of Plint There Shall Be Rcc Work In Ratio 1:3:6 [Cement, Sand And Grit Stone] By Using 12 Mm Dai Ms Bar At Distance Of 9. There Shall Be Plastering All Over The Plinth 12 Mm Thick In Ratio 1:4 [Cement And Sand] Above The Ground Level. Proper Watering And Curing Of The Plinth Shall Be Carried Out As Per Direction Of Supervising Engineer. , Fencing Of 250 Kva T/Fs As Per Following Specification -Fabrication Of 50X50x6 Mm Size Ms Angle Frame Of Size 3000X2400mm With 450 Mm Long Angle For Grouting The Frame And Fixing Of 2X1.5, 10 Swg Welded Wire Mesh With Ms Strip Of 24X5mm Size All Round The Frame And Drilling 9 Mm Holes Insides Of Frames At As Distance Of 300Mm For Jointing Of Frame With The Help Of Boslts And Nuts Including Cost Of Material. The Width Of Panal May Vary As Per Site Conditions, Grouting And Fixing Of Angle Iron Frames In Ratio 1:2:4 (Cement, Coarse Sand And Stone Ballast ) In The Pocket Of 150X150x150mm All Round The Plinth And Bolting Of Frames With 25X8 Mm Size Bolts And Nuts, Making Main Gate In Front Of The Plinth Of Size 3000X2400 Mm By Making Two Leaves Of Size 3000X1200mm Size And Grouting The Same In Ratio And Method Mentioned At Item (B) Above Fixing With Hinges With Dandlas For Locking System & Painting Of Entire Wire Mesh Angle Iron Etc. With Bus Green Super Enamelled Pain In Two Coats On The Primer Two Coats Of Red Oxide. , Earthing With Strip Of 250 Kva Distribution Transformer By Maintenance Free Earthing Electrods (Chemical) By Digging Pits 6 Dia 3Mtr. Deep Including Inserting Pipe In Pipe Technology Concept Involve Two Mild Steel Pipes One Inserted Inside The Other Of Size ;- 1. Inner Pip Dia Meter 50 Mm. 2. Outer Pipe Dia Meter 100 Mm. Length Of The Both Pipe Shall Be 3000 Mm. The M.S.Pipe Shall Be Isi Mark Of Class B As Per Is 1239. Thickness Of The Pipe Shall Be 12 Swg. The Empty Space In The Pipe Shall Be Filled With The Specially Developed Crystalline Material Conductiv Mixture Such As Copper And Aluminimum Powder.Conductive Carbon And Bonding Material Etc. Mixed In Diffrent Proportions. Conductive Mixture Contents Shall Be 70 % Carbon Powder & 30% Metal Powder Preferably Pure Copper Or Aluminum Material Along With The Required Quantity Of Bonding Materials. Granule Size Of The Carbon & Metal Powder Shall Be 100 Mesh. The Mixture If Forced (Pressurized) Inside The Earth Electrode In Empty Space Of Inner Pipe & In Empty Space Between The Inner & Outer Pipe Of The Earth Electrode, In Paste Form And After Soldification Of The Same The Bottom End Cap As Well As Top End Cap Is Provided. The Mixture Shall Be Pressed By Machine In The Pipe. Precaution Shall Be Taken Has To Have No Air Gap Inside The Pipe While Pressing. The Back Fill Compound (Earth Enhancment Material ) Shall Be Superior Conductive Material That Improves Earthing Effectiveness Especially In Areas Of Poor Conductivity Such As Rocky Ground, Sandy Soil & Areas Of Moisture Varation. It May Contain Conductive Cement (20%) Graphite Carbon Powder(50%), Hydrous Aluminum Siliacate (10%), Sodium Montmorillonite (20%) Etc. It Shall Be Placed Around Earth Electrode In The Earth Pit To Improve The Conductive Of Earth Electrode & Ground Contact Area. Mild Steel Electro Galavanized Flat 50X6 Mm Shall Welded To Earth Electrode Pips & Connected With Trasnformer Neutral And Body As Below With The Hlep Of Steel Nut & Bolt Or Through Welding As Per Requirment Of Site, To Gi Pipe And Filling Of Chemical Mixutre Around The Gi Pipe Upto 3 Mtr. Including Making Of Chamber & Connecting The Top Of The Inserted Pipe With Transformer Body & Neutral Through M.S.Flat 50X6mm With The Help Of Nut & Bolt Or Through Welding And Making A Main Hole Of Size 2×2 And Covering The Same By A Stone Pad For The Purpose Of Poring Water For Moisture. , Installation For 250 Kva T/F On Plinth In Proper Alignment Direction & Making Ht/Lt Connection All Cost Of Labour And T&P Which Required For Completion Of Work. , Mounting & Installation Of 63 Kva T/F On Plinth In Proper Alignment Direction & Making Ht/Lt Connection All Cost Of Labour And T&P Which Required For Completion Of Work. , Laying Of Lt Xlpe Lt Xlpe Cable 3.5 Core 250/400/630Sqmm,Lt Xlpe Single Core Cable 250/400/630Sqmm As Per Respo Norms And Direction By Superivising Engineer. , Fixing Of Distribution Box With Cl On Errected Pole For Giving Supply To Consumer By Connecting Consumer Cables. , Fixing Of Pole Earthing Complete As Per Respo Norms Including The Cost Of Arrangement Of Labour, T&P, Carrier Etc. Required For Proper Completion Of Work. , Laying, Sagging, Stringing, Binding And Jumpering Of Acsr Weasal Conductor/ Dog Conductor/ Rabbit Conductor In 33/11Kv Line As Per Respo Manual And As Per Direction Of Supervising Engineer. It Includes The Cost Of Labour, T & P, Carrier Etc Reauired For Proper Completion Of Work. , Laying Sagging Stringing And Binding And Jumpering Of Conductor In Lt Line As Per Respo Manual And As Per Direction Of Supervising Engineer. It Includes The Cost Of Labour, T & P, Carrier Etc Reauired For Proper Completion Of Work. Abc 3X50/120Sqmm , Laying Of 33/11 Kv Xlpe Cable 3X300 Sqmm Through H.D.P.E.Pipe By Drill Machine/H.D.D. Machine Including The Cost Of Arrangment Of Labour, T&P & Drill Machine/H.D.D. Machine At A Depth As Per Railway Norms. Below The Railway Crossing. , Laying Of Lt Xlpe Cable 3.5X70 Sqmm Overhead With Making Loop As Per Respo Norms And Direction By Superivising Engineer. , Concreting Of Stay Erection Complete In All Respect As Direction By Supervising Engineer. All Required Material Provided By Contractor At His Own Cost , Laying Of 33 Kv Xlpe Cable 3X300 Sqmm Through Gi Pipe And Mounting On Double Pole As Per Respo Norms And Direction By Superivising Engineer. , Laying Of 11 Kv Xlpe Cable 3X185 Sqmm/3X300sqmm Through H.D.P.E.Pipe By Drill Machine/H.D.D. Machine Including The Cost Of Arrangment Of Labour, T&P & Drill Machine/H.D.D. Machine At A Depth As Per Railway Norms. Below The Railway Crossing. , Filling Of 11 Kv Jointing Kit 3X300/ 3X185/ 3.5X70 Sqmm Od/Id And Making Connection As Per Direction By Supervising Engineer. , Filling Of 33 Kv Jointing Kit 3X300 Sqmm Od/Id And Making Connection As Per Direction By Supervising Engineer. , Installation Of 11Kv Do Fuse Set Complete As Direction By Supervising Engineer. , Installation Of Stay Set Complete As Direction By Supervising Engineer. , Erection Of Gaurding Below 33/11Kv Overhead Line Using 6 Swg Gi Wire Complete With Gaurding Engle Cl S Nut & Bolt Binding And All Necessary Complete In All Respects As Per Respo Norms , Dismentling & Removal Of 100 Kva T/F And Recived Back To Ele. Store Center Taj Agra , Dismentling, Removal Of Old & Used Scrap Material And Received Back To Ele. Store Center Taj Agra Including Loading, Unloading Both Ends (0-50Km)
|
