|
Bids Are invited for Repair, Maintenance, And Installation Of Plant/ Systems/Equipments (Version 2) - Hospital; Electrical System Or Installation; Service Provider - Gss Ducting:- Supplying Fabrication Installation Testing And Commissioning Of Gi. Sheet Metal Ducting. Zinc Coated. Complete With All Standard Accessories, G.I.. Hardware, Self Adhesive Elastomeric Foam Gasket, Support Etc As Per Smacna Specification.Gss Ducting:- 20 Swg , Supply And Installation Of Volume Control D Ers, Bypass D Ers. , Providing Aluminium Supply Air Diffusers & Return Air Grills With Volume Control D Ers , 415V Pump Panel With 63A Mccb As Incomer With Phase Indicator And Ammeter & Voltmeter With Selector Switches, 2Noss. Of 25A Mpcb With Dol Starter, Local Push Button Station & Contactor Of Required Rating As Outgoing. , 50 X 50 X 6 Mm Of M.S.Angle. , Providing, Detailing, Fabricating And Fixing At Desired Location Using M.S. Chequered Plates Of Any Thickness And Of Grade Fe250 As Per Specifications And Approved Fabrication Drawings (Which Are To Be Prepared By Contractor And Got Approved From Engineer), Including Transporation Of The Same To Site, Erection At All Heights And Levels, Provision Of Necessary Erection Bolts, Fixing Bolts, Nuts, Washers, Cleats, Stiffeners, And All Necessary Operations Like Preheating As Per Specifications, Straightening, Bending, Cutting, Drilling, Grinding, Machining If Specified, Welding, Grinding And Removing The Welding Burr And Preparing Surface For Painting With Wire Brush Cleaning And Applying Two Coats Of Epoxy Red Oxide Zinc Phosphate Primer Of 30 Microns Each And Two Coats Of Epoxy Corrosion Resistant Enamel Paint Of 30 Microns After Fabrication Including Touching Up With Spray Painting After Erection Etc Complete As Directed By Engineer In Charge. , Providing, Detailing, Fabricating And Fixing At Desired Location Using Hot Rolled Sections And Ms Plates Of Grade Fe 250 As Per Specifications And Approved Fabrication Drawings (Which Are To Be Prepared By Contractor And Got Approved From Engineer), Transporting To Site And Erecting Structural Steel Members For All Heights & At All Levels Including Provision Of Necessary Erection Bolts, Fixing Bolts, Nuts, Washers, Cleats, Stiffeners, Gussets, Base Plate, And All Necessary Fixtures And Operations Likepreheating As Per Specifications, Straightening, Bending, Cutting, Drilling, Grinding, Machining If Specified, Welding, Grinding And Removing The Welding Burr And Preparing Surface For Painting With Wire Brush Cleaning And Applying Two Coats Of Epoxy Red Oxide Zinc Phosphate Primer Of 30 Microns Each And Two Coats Of Epoxy Corrosion Resistant Enamel Paint Of 30 Microns After Fabrication Including Touching Up With Spray Painting After Erection Etc Complete As Directed By Engineer In Charge. (The Qty. For This Item Shall Be Measured For Gusset Plates, Base Plates, Bolts In M.T.) , Cement Mortar 1:3 (1 Cement : 3 Coarse Sand) , 1St Category Cu Armoured Cables Frlsz Outer Sheathed- 6Cx 6Sq.Mm , 1St Category Cu Armoured Cables Frlsz Outer Sheathed- 4C X 16 Sq.Mm , Cable End Termination For Copper Cables – 4C X 16 Sq.Mm , 100A Tpn Mccb , Providing & Fixing Of Canvas Connections For Units. , Use Of Scarf Folding As Per Space Accommodation (4Ftx8ft) For Ug To Terrace Of C Wing And F Wing , Sitc Of Centrifugal Exhaust Blower Assembly For Capacity Of Approx. 8000 Cum / Hr. And Shall Be Fabricated From Ss 304 Material. The Blower Assembly Shall Have Silencer With Anti-Vibration Absorbed To Reduce Noise With 10 Hp Motor Arrangement.
|
