|
Fuel Injector Mtz 82.1 D-240 Is Original. Catalog Number 171.1112010-50. Main Technical Characteristics: Injection Start Pressure: 180+5 Kgf/Cm² (Mpa). Installed Sprayer: 6A1-20S2-50 (Marked “50”). Number Of Spray Holes: 5 Holes With A Diameter Of 0.32 Mm. Effective Flow Area (Μ F): 0.240–0.260 Mm². Contents: Requirements For Factory Adjustment, Protective Plugs And Individual Packaging. Compliance With St Rk Gost R 53489-2011 System Of Labor Safety Standards For Mounted And Trailed Agricultural Machines. General Safety Requirements. Warranty 1 Year From The Date Of Signing The Acceptance Certificate., The Rear Axle Axle Shaft Of The Old Model Mtz 82.1 (With Locking Splines) Is Original. Catalog Number 50-2407082-A. Design Features: Mandatory Presence Of A Splined Shank On The Inner End Of The Shaft For Installation Of The Differential Lock Drive Gear. Overall Length - Not Less Than 975 Mm And Not More Than 980 Mm. Spline Connection Parameters: Inner End (For Locking): Diameter 68 Mm, Number Of Splines - 14. Main Working Part (For Differential): Diameter 95 Mm, Number Of Splines - 20. Shaft Diameter: Wheel Hub Mounting Side: 75 Mm. Material And Processing: High Strength Alloy Steel. The Surface Of The Part Must Be Hardened With High Frequency Currents (Hfc) In Areas Of Increased Wear (Working Areas Under Bearings And Splines) To Ensure Hardness And Wear Resistance. Approximate Weight: Between 35.0 – 37.0 Kg. The Product Must Be New, Not Used, Not Restored, Without Defects (Cracks, Shells, Chipped Splines, Traces Of Corrosion). Compliance With St Rk Gost R 53489-2011 System Of Labor Safety Standards For Mounted And Trailed Agricultural Machines. General Safety Requirements. Warranty 1 Year From The Date Of Signing The Acceptance Certificate., Rear Axle Axle Sleeve (Stocking) Mtz 82.1 Original. Catalog Number 502407018-A. Main Technical Characteristics: Design Feature Of The Casting: Modification Of The Body Must Include Special Technological Bosses With Holes For Bolting The Base Of The Tractor Cabin (For Tractors With A Unified “Large” Cabin). Installation Side: Symmetrical Design Of The Housing (Interchangeable, Suitable For Both The Left And Right Side Of The Rear Axle). Material Of Manufacture: High-Strength Cast Iron Or Cast Steel, Resistant To Variable Dynamic Loads, Fracture And Deformation. Approximate Overall Dimensions Of The Part: Length - At Least 400 Mm; Width - Not Less Than 370 Mm; Height - At Least 360 Mm. Part Weight: In The Range From 35 Kg To 42 Kg (To Ensure The Design Rigidity Of The Unit). Requirements For Quality, Safety And Completeness: Product Condition: The Product Must Be New, Not Used, Not Refurbished, Not Repaired, Produced No Earlier Than 2025-2026. Delivery Set: Axle Shaft Sleeve (Housing) - 1 Pc. The Product Is Supplied In Original Packaging (Or With A Protective Coating Against Corrosion), Ensuring Safety During Transportation. Compliance With St Rk Gost R 53489-2011 System Of Labor Safety Standards For Mounted And Trailed Agricultural Machines. General Safety Requirements. Warranty 1 Year From The Date Of Signing The Acceptance Certificate., The High Pressure Fuel Pump (Hpf) Is Original, Assembled With A Regulator. Catalog Number (Article): 4Utnm-1111005-01. Technical Characteristics: Pump Type: In-Line, 4-Piston, With Mechanical Centrifugal All-Mode Regulator. Injection Pump Drive (Connection Type): Splined Flange (“Ignition Plug”) With 3 (Three) Bolts. Pumps With A Splined Bushing (For A Closed Plate) Or Flanges For 2 Bolts Are Not Allowed For Delivery. Lubrication System: Autonomous (Own Pump Oil Sump, Isolated From The Engine Lubrication System). Fuel Supply Corrector: Mechanical. Contents: The Pump Is Supplied Assembled With A Regulator, A Low-Pressure Booster Pump (Pump) And Has Protective Transport Plugs On The Fittings. Requirements For The Quality, Condition And Safety Of The Product: The Product Must Be New, Not Used (In Operation, Under Repair), Not Refurbished, Assembled From New Components, Manufactured No Earlier Than 2025. Build Quality: The Housing Must Not Have Cracks, Chips, Signs Of Corrosion, Or Leaks Of Fuel And Lubricants. Threaded Connections Must Be Tightened In Accordance With The Manufacturers Specifications. Bench Tests: The Injection Pump Must Be Adjusted At The Manufacturer (Or A Specialized Certified Service Center) To The Nominal Performance Parameters, Starting Feed And Uniformity Of Feed Across Sections. Compliance With St Rk Gost R 53489-2011 System Of Labor Safety Standards For Mounted And Trailed Agricultural Machines. General Safety Requirements. Warranty 1 Year From The Date Of Signing The Acceptance Certificate.
|
