|
Door Contact. An Electrical Microswitch Or Contact Sensor Installed In The Doors Of The Elevator Car Or Shaft To Determine Their Position (Open/Closed)., Contactor 110 V, 32 A Ac, Floor Indication Board For Passenger-And-Freight Elevator (Step), Contactor 110 V, 25 A Dc, Incremental Rotary Encoder. Power: Dc5v, Interface: 1Vpp Incremental Signals (2048 Pulses/Rev)., Contactor 110 V, 32 A Dc, Mine Door Lock, Left, Shoe Insert Dx-20. Type: Replacement Insert (Lining) Of The Elevator Car Shoe, Purpose: Ensuring Smooth And Silent Sliding Along The Guide, Guide Diameter: 16 Mm, Dimensions: ≈ 180 × 25 × 8 Mm, Material: Wear-Resistant Polymer (Polyamide / Polyurethane), Design: Sliding Element Enclosing The Guide Rail, Application: Elevator Cabin (Step System), Contactor 110 V, 9 A Ac, Interface/Signal Board For Elevator Control System. Type: Printed Electronic Board (Pcb) For Step Elevator. Main Functions: Receiving/Transmitting Control Commands, Communication With The Controller And Sensors. Board Dimensions: ≈ 120 × 80 × 30 Mm, Layering. A Mechanical Element Of A Door System Or Car Positioning System Involved In Moving Doors, Releasing Locks, Or Interacting With Hoistway Mechanisms At Desired Positions During Elevator Operation. Type: Mechanical Pull/Pull/Lever Element Of Door System, Material: High Strength Steel Or Alloy With Protective Coating, Application: Automatic Car And Shaft Doors In Elevators, Photocell. Infrared Optical Safety Sensor Used To Detect Obstacles In The Area Of Moving Parts In Automatic Elevator Doors., Power Supply (24V,4.5A,100W) Is A Stabilized Switching Power Supply Used In The Step Elevator Control System To Provide Stable Power To Electronic Modules And Automation Devices. Output Voltage: 24V Dc, Output Current: 4.5A, Power: 100W, Input Voltage: 100–240V Ac, Board Sm.02/H Pro D0955bv3 (Step), Type: Control Board (Car-Top Control / Communication Board), Purpose: Control And Communication Of Elevator Car Equipment, Installation: Elevator Car Roof, System: Step (Compatible With Step Controllers), Communication Interface: Canbus, Power Supply: 24 V (Typical For Elevator Boards), Dimensions: ~200 × 150 × 100 Mm (Approximately Based On Analogues), Weight: ~0.1–0.3 Kg, Contactor 110 V, 25 A Ac, Magnetic Reed Sensor Is A Position Sensor Designed To Detect The Full Opening Of The Elevator Car Doors. Purpose: Determination Of The “Door Fully Open” Position In The Elevator Safety System. Type: Magnetic Reed Switch (Contact) Sensor. Operating Voltage: 5–30V Dc. Temperature Range: -40°C … +80°C. The Sensor Is Triggered At A Distance Of: 2–15Mm. Maximum Load Current: 50Ma (Max). Operating Frequency: ≈ 1Khz., Mine Door Lock, Right, Cabin Door Drive Controller. Purpose: Control Of The Operation Of The Elevator Door Drive, Processing Of Opening/Closing Commands And Safety Signals From The Elevator Control System, Photocell Light Curtain For Elevators. Purpose: Control Of The Elevator Door Area, Passenger Safety. Type: Protective Light Curtain (Photocell), Supply Voltage: Ac220 V. Number Of Beams: Up To 94 (Max.), Detection Range: 0–3 M. Operating Temperature: -20°C ... +65°C, Dimensions: ≈ 2000 × 24 × 11 Mm (Height × Width × Thickness) - For Main Bar With Ir Rays. Features: Status Indication, Wide Detection Angle And Range, Noise Alarm When Triggered., Cab Door Drive Electric Motor. Three-Phase Asynchronous Electric Motor.
|
