|
Red Enamel (Glossy). Technical Characteristics: Blue Enamel Pf-115. (Glossy) Description It Is A Suspension Of Rutile Titanium Dioxide And Other Pigments And Fillers In Pentaphthalic Varnish With The Addition Of A Drier, Solvents And Targeted Additives. Purpose Intended For Painting Metal, Wood And Other Surfaces Exposed To Atmospheric Influences And For Painting Indoors. Enamel Coatings Have High Protective And Decorative Properties. The Film Combines Sufficient Hardness With High Elasticity And Durability. The Enamel Film Is Resistant To Temperature Changes From Minus 50 To Plus 60 ºс. A Coating Consisting Of Two Layers Of Pf-115 Enamel Applied To A Prepared Primed Surface In Temperate And Cold Climates Retains Protective Properties For Four Years Up To A Score Of No More Than Az1 And Decorative Properties For One Year Up To A Score Of No More Than Ad2. Technical Characteristics 1. The Color Of The Enamel Coating Must Be Within The Permissible Deviations Established By The “Card Index” Color Samples Or Control Color Samples Approved In The Prescribed Manner. 2. Appearance Of The Coating After Drying, The Enamel Should Form A Smooth, Uniform Surface Without Delamination, Pock Marks, Streaks, Wrinkles And Foreign Inclusions. A Small Amount Of Shagreen Is Allowed. 3. Gloss Of The Coating According To A Photoelectric Gloss Meter, %, Not Less Than 50 5. Mass Fraction Of Non-Volatile Substances, %, Depending On Color 49-70 Color Blue 6. Degree Of Dilution To Viscosity 28-30 S According To A Vz-246 Type Viscometer With A Nozzle Diameter Of 4 Mm At A Temperature Of (20.0±0.5)ºс, %, Not More Than 20 7. Degree Of Grinding, Microns, No More Than 25 8. Covering Capacity Of The Dried Film, G/M2, No More, Depending On The Color 30-120 9. Drying Time To Degree 3 At A Temperature Of (20±2)ºс, Hours, No More, For Enamels Of Colors: 24 10. Packaging Metal And Plastic Containers In Containers Of 10 Liters Each. Gost 6465-76 Odorless, White Enamel Pf-115. (Glossy) Description It Is A Suspension Of Rutile Titanium Dioxide And Other Pigments And Fillers In Pentaphthalic Varnish With The Addition Of A Drier, Solvents And Targeted Additives. Purpose Intended For Painting Metal, Wood And Other Surfaces Exposed To Weather Conditions And For Painting Indoors. The Enamel Film Is Resistant To Temperature Changes From Minus 50 To Plus 60 ºс. Technical Characteristics 1. Color Of Enamel Coating. Gloss Of The Coating According To A Photoelectric Gloss Meter, %, Not Less Than 50 5. Mass Fraction Of Non-Volatile Substances, %, Depending On Color 49-70 Color White 6. Degree Of Dilution To Viscosity 28-30 S According To A Vz-246 Type Viscometer With A Nozzle Diameter Of 4 Mm At A Temperature Of (20.0±0.5)ºс, %, Not More Than 20 7. Degree Of Grinding, Microns, No More Than 25 8. Covering Capacity Of The Dried Film, G/M2, No More, Depending On The Color 30-120 9. Drying Time To Degree 3 At A Temperature Of (20±2)ºс, Hours, No More, For Enamels Of Colors: 24 10. Elasticity Of The Film When Bending, Mm, No More Than 1 11. Strength Of The Film When Impacted Device Type U-1, Cm, Not Less Than 4 12. Coating Hardness According To A Pendulum Device Type Tml (Pendulum A), Relative Units, Not Less Than 0.10 13. Film Adhesion, Points, Not More Than 1 14. Resistance Of The Coating At A Temperature Of (20±2)ºс To The Static Influence Of Water, H, Not Less Than 2 15. Resistance Of The Coating To Static Influence 0.5% Detergent Solution, Min, Not Less Than 15 16. Resistance Of The Coating At A Temperature Of (20±2)ºс To The Statistical Influence Of Transformer Oil, H, Not Less Than 24 17. Gost Notes: When Using Enamels, Hot Drying Of The Coating At A Temperature Of (105-110) °C For 1 Hour Is Allowed. Application The Dried Coating Is Safe For Humans. Packaging Metal And Plastic Containers In Containers Of 20 Liters Each. Gost 6465-76 Odorless, Green Enamel (Glossy). Technical Characteristics: Blue Enamel Pf-115. (Glossy) Description It Is A Suspension Of Rutile Titanium Dioxide And Other Pigments And Fillers In Pentaphthalic Varnish With The Addition Of A Drier, Solvents And Targeted Additives. Purpose Intended For Painting Metal, Wood And Other Surfaces Exposed To Atmospheric Influences And For Painting Indoors. Enamel Coatings Have High Protective And Decorative Properties. The Film Combines Sufficient Hardness With High Elasticity And Durability. The Enamel Film Is Resistant To Temperature Changes From Minus 50 To Plus 60 ºс. A Coating Consisting Of Two Layers Of Pf-115 Enamel Applied To A Prepared Primed Surface In Temperate And Cold Climates Retains Protective Properties For Four Years Up To A Score Of No More Than Az1 And Decorative Properties For One Year Up To A Score Of No More Than Ad2. Technical Characteristics 1. The Color Of The Enamel Coating Must Be Within The Permissible Deviations Established By The “Card Index” Color Samples Or Control Color Samples Approved In The Prescribed Manner. 2. Appearance Of The Coating After Drying, The Enamel Should Form A Smooth, Uniform Surface Without Delamination, Pock Marks, Streaks, Wrinkles And Foreign Inclusions. A Small Amount Of Shagreen Is Allowed. 3. Gloss Of The Coating According To A Photoelectric Gloss Meter, %, Not Less Than 50 5. Mass Fraction Of Non-Volatile Substances, %, Depending On Color 49-70 Color Blue 6. Degree Of Dilution To Viscosity 28-30 S According To A Vz-246 Type Viscometer With A Nozzle Diameter Of 4 Mm At A Temperature Of (20.0±0.5)ºс, %, Not More Than 20 7. Degree Of Grinding, Microns, No More Than 25 8. Covering Capacity Of The Dried Film, G/M2, No More, Depending On The Color 30-120 9. Drying Time To Degree 3 At A Temperature Of (20±2)ºс, Hours, No More, For Enamels Of Colors: 24 10. Packaging Metal And Plastic Containers In Containers Of 10 Liters Each. Gost 6465-76 Odorless
|
