|
Tender for Repair To Pumping Machinery Of 5 Cusec Vt Pump Set Of Unit Iv Along With Extension Of Column Pipe And Other Allied Works At Lis Katal Batal. , The Job Involve Disconnecting The Electrical Connection Of Motor Of Unit Iv And Dismantling The Slip Ring Motor From The Ratchet Assembly By Way Of Decoupling The Required Coupling Nuts And Bolt. Lifting The Motor From Base Frame With The Help Of Existing Mono Rail And Chain Pulley Block, Then Keeping It Aside. Dismantling The Ratchet Assembly From The Discharge Head And Lifting It Aside. Dismantling The Delivery Line From The Discharge Head And Suction Column By Way Of Unscrewing The Required Nuts And Bolt. Lifting The Discharge Head And Keeping It Aide. Extracting Out The Column Suction Pipe, Line Shaft, Spider Guide One By One By Way Of Dismantling The Required Nut And Bolt And Unscrewing The Line Shaft From Each Socket, Then Finally Extracting Out The 2 Stage Vt Pump Of 5 Cusec Discharge, Head Load Carriage Of Pump, Line Shafts, Sleeves, Stuffing Box And Sockets Along With Discharge Head To Road Side Up To Loading Point With The Help Of Skilled Manual Labour And Then Loading Into A Mechanical Transport For Carrying To Work Shop For Repairs With The Help Of Crane/Tools, Tackles Using Manual Labour. Complete Job Includes Cost Of Labour, Carriage Charges And Hire Charges Of Tools And Tackles. Repair To Stuffing Box By Providing And Fitting Of New Bronze Bush As Per Sample To Required Size After Re Metalling, Finishing And Drilling Holes And Making Internal Threads On Stuffing Box As Per Requirement For Securing Studs. Repair To Top Shaft By Way Of Rebuilding With Machine Able Ss Electrode At Worn Out Portions And Then Threading And Making Key Way Of Required Size. Dismantling The 2 Stage Vt Pump By Way Of Cutting Of Rusted Bolts, Nuts And Studs And Separating The Discharge Bowl, Suction Bowl From Pump Body And Then Dismantling The Two Stage Pump To Extract The Damaged Impellers And Pump Shaft. Repairs To 05 Cusec Vt Pump By Way Of Providing/ Fitting Of Neck Ring Of Stainless Steel Material- 02 Nos. By Casting, Turning And Boring To The Required Size And Press Fitting The Same In The Pump Body Then Locking Properly. Repair To Pump Shaft By Way Of Welding Turning And Finishing To Required Size And Then Threading It And Making Of Key Way On Shaper To The Required Size. Repair To Ist And Iind Stage Impeller By Fabrication Of 1 No. Neck Ring Each For Impellers And Then Press Fitting It On The Impeller And Locking It Properly And Rebuilding The Worn Out Portion With Machine Able Ss Electrode And Turning, Machining It To Its Original Shape And Size. Repair To Stuffing Box By Providing And Fitting Of New Bronze Bush As Per Sample To Required Size After Metalling, Finishing And Drilling Holes And Making Internal Threads On Stuffing Box As Per Requirement. Repair To Top Shaft By Way Of Rebuilding With Machineable Ss Electrode At Worn Out Portions And Then Threading And Making Key Way On Shaper To The Required Size. Fabrication Of New Check Nut Of Given Size. Providing And Fitting Of New Ci Spider Guide 01 Nos. Along With Rubber Bush As Per Sample. Fabrication/ Providing And Fitting Of 04 Nos Pump Body Bushes. Repairs To 02Nos Line Shaft By Way Of Welding, Turning And Making Threads As Per Sample. Providing And Fitting Of 02 No Sleeve For Line Shaft By Making Internal Threads Of Required Size. providing and Fixing Of Rubber Sheet Joints For Flanges 05 Nos Cut To Required Size. The Job Includes Fitting Of The Pump Using New Nuts And Bolts/ Studs. Fabrication/ Providing And Fitting Of Well Mouth As Per Sample And Strainer To The Bell Mouth Of Pump Body.Connecting The Bottom Suction Pipe Piece With The Pump Body Along With Line Shaft With Socket And Required Nuts And Bolts And Rubber Sheet Joints Of Appropriate Size Then Lowering The Pump In The Sump Using Tools And Tackles With The Help Of Manual Labour And Existing Chain Pulley Arrangement. Connecting All The Suction Pieces With Required Nuts, Bolts And Rubber Sheet Joints, Line Shaft With Socket, Fixing Of Spider Guide On Line Shaft Ensuring That The Spider Guide Bush Remain At Center Of Sleeves.Fitting All The Suction Pipes, Line Shaft, And Spider Guide In Similar Manner. Fabrication/Providing And Fitting Of New Suction Column Of 10 Inch Dia Of 2.5Ft Approximately With Flange Welded To Its Ends Along With Line Shafts, Spider Guides, Sleeves And Socket If Required. The Flanges Should Have 2.5 Inch (Min) Collar Width And 16Mm Thickness. The Pipes Ends Should Have Been Faced To Accommodate The Spider Guide Accurately Without Any Play. The Ends Of Pipes Should Have 04 Nos Wedge Welded To Their Ends To Support/ Give Strength To Welded Flanges. Then Fitting The Additional Fabricated Pipe Piece Before Discharge Head On The Top Piece Of Suction Pipe With Required Nuts, Bolts And Rubber Sheet Joints, Fitting The Stuffing Box With Gland Set And Gland Packing, Fitting Of Ratchet Assembly, Then Assembling The Motor By Providing And Fitting Bushes Of Appropriate Sizes And With Existing Coupling Nuts, Bolts. Giving All The Electric Connection And Testing The Running Of Pump On Full Load And Checking Of Any Type Of Leakage At Suction Column Joints.Complete Job Includes Cost Of Material, Hire Charges Of Tools And Tackles Required For Execution Of Job, Carriage, Transportation, Labour Charges And Testing Complete At Lis Katalbatal. Material Of Construction Should Be As Below:- I Line Shaft/ Line Shafts Sleeves :- Stainless Steel (Aisi-410) Ii Column Pipes Complete As Per Site Condition. :- Steel As Per Is: 210 Of 1978/Grade A Of Is:2062 1984 With Latest Amendments And Is: 4270 Iii Nuts And Bolts :- High Tensile Steel Iv Line Shaft Coupling :- Steel As Peris1030 Of 1982 With Latest Amendment V Other Component :- Conforming To Is 1710 With Latest Amendments For Such Duty, Head Variations And Quality Of Raw Water Vi Thickness Of Pipe :- 08Mm Dismantling The 120 Hp Oil Immersed Star Delta Starter From Installed Position Of Pumping Unit No. Iv After Disconnecting All Electrical Connections From Input And Output Side. Loading In Transport For Carriage To Workshop For Repair. Repair To Starter By Way Of Extracting Out The Damaged Copper Contact Points Both Moving And Fixed, Thimbles, No Volt Coil, Tripping System, Overload Relay And Replacing The Same With New Ones, Repairs To Operating Mechanism. Providing/Filling Of 20 Liters Transformer Oil For Topping Of Starter After De-Moisturizing The Existing Oil. Back Carriage Of The Starters To Lis. Installation Of Starter By Proving And Fitting New Nuts And Bolts Required Commissioning And Test. Giving All The Electric Connection By providing and Fixing New Thimbles Of Appropriating Rating/Size. Note: The Bidders Are Advised To Visit The Site And Quote The Rates Including The Rebate On Old Material. Any Modification/Alternation If Needed At The Time Of Execution Of Job Shall Be Carried Out At Site Accordingly , Rebate On Old Parts
|
