Tender For Lac-Ads-Establishment Of Open Gym- At Ward 10 Near Perayam Grama Panchayath Ground In Perayam Gra ... in India

Work Detail

Tender For Lac-Ads-Establishment Of Open Gym- At Ward 10 Near Perayam Grama Panchayath Ground In Perayam Grama Panchayath In Kundara Lac, Kollam - Supply And Installation Of Open Gym Equipment - Retender , Supply And Installation Of Open Gym Equipment , Od271264/2025-2026 Rower - Supply And Installation Of Rower Having The Following Specifications: Dimensions: (L X W X H) = 1472 X 915 X 1040 Mm. Upper And Bottom Pipes Ø88Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Angle Between Handle And Horizontal Surface Is 75 - 80 Degree. Linkages Ø 48 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Seat & Back Rest &Ndash; 380 X 275 X 60Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Foot Resting Pipe - Ø 60 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. End Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø250 Mm & 8Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe.Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Pin &Ndash; Ø 25 Mm M.S. Bright Bar Pin. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Bearing Bushes - Ø 60 Mm Od Seamless Pipe / Bar. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Grips &Ndash; High Quality Rubber 46 Mm Od. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271265/2025-2026 Air Walker - Supply And Installation Of Air Walker Having The Following Specifications: Dimensions: (L X W X H) 1190 X 380 X 1244 Mm. Main Frame- Ø 88 Mm Od &Quot;B&Quot; Class Gi Pipe Dually Bending Design. Foundation Plate- M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Ø 42 Mm Od Round Gi Pipe. Handle - Ø 33 Mm Od &Quot;B&Quot; Class Gi Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use To Support It. Top Closing Cap Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap'S - Pp / Nylon / Hdpe Material. Bracket - 8 Mm Thick Laser Profile Is Used To Support Paddle Frame. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Beused To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Pin'S Ø 25Mm M.S. Bright Bar Pin. Circlips- A 24 Circlips Are Used For Assembly. Bearing Bushes -Ø 60 Mm Od Seamless Pipe. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271266/2025-2026 Horse Rider - Supply And Installation Of Horse Rider Having The Following Specifications: Dimensions: (L X W X H) 1140 X 400 X 1400 Mm. Main Frame - Ø 114 Mm Od B Class Gi Pipe. Foundation Plate M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame Is Made By Ø 48 Mm Od B Class Gi Pipe. Seat Frame Is Made By Ø 48 Mm Od B Class Gi Pipe. Seat Position Must Be Horizontal To 110 -120 Degree. Link - Made Up Of Ø 48 Mm Od B Class G.I. Pipe. Angle Between Link And Ground Position Is 10-20 Degree. Handle - Ø 33 Mm Od B Class Gi Pipe. Paddle Vertical Support - Ø 60 Mm Od B Class Gi Pipe. Handle Frame- Ø 42 Mm Od B Class Gi Pipe Dually Bending Design. Foot Pipe - Ø 33 Mm Od B Class Gi Pipe. Support Frame 10 Mm Thick Ms Flat Is Used. Seat- Dimension 320 X 270 X 100 Mm Blow Moulded Wall Thickness 4Mm Material Hdpe. Bearing Bush Closing Cap Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin Made Of Ø 25 Mm M.S. Bright Bar. Grips - High Quality Rubber Ø 46 Mm Od. Circlips A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 60 To 70 Micron. Safety Instructions And Exercise Chart - Start &Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271267/2025-2026 Back Extension - Supply And Installation Of Back Extension Having The Following Specifications: Dimensions: (L X W X H) 1060 X 730 X 990 Mm. Main Frame - Made From Ø 88 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 42 Mm Od &Ldquo;B&Rdquo; G.I Pipe. Seat Rest Pipe &Ndash; Ø 42 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Handle Pipe &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 3 Mm Thick Used To Support It. Footrest Pipe &Ndash; Ø 42 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe And 80 X 40 Mm Ms Rectangular Pipe. Closing Cap &Ndash; Pp / Nylon / Hdpe Material. Seat &Ndash; 360 X 300 X 2 Mm Thick M.S. Seat With Corner Fillet For Safety. Grips - High Quality Rubber Ø 46 Mm Od. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271268/2025-2026 Shoulder Builder (Double) - Supply And Installation Of Shoulder Builder Having The Following Specifications: Dimensions: (L X W X H) 890 X 558 X 1500 Mm. Main Frame - Made From Ø 114 Mm Od &Quot;B&Quot; Class G.I. Pipe. Foundation Plate -M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Shoulder Ring Pipe - Ø 33 Mm Od &Quot;B&Quot; Class G.I Pipe. Shoulder Ring Pipe Support - Ø 25 Mm Od &Quot;B&Quot; Class G.I Pipe. Nylon Knob With Bearing Is Fixed On Shoulder Ring Pipe For Rotating Purpose (2 Set To Be Fixed In A Position For Kids And Adults). Top Closing Cap'S- Pp / Nylon / Hdpe Material. Closing Cap - Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin Ø 25 Mm M.S. Bright Bar Pin. Foundation Plate M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlips A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In - Charge Before Installation.) , Od271251/2025-2026 Chest Press (Double) - Supply And Installation Of Double Chest Press Having The Following Specifications: Dimensions: (L X W X H) 1955 X 710 X 1900 Mm. Main Center Pipe - Ø 114 Mm Od ?B? Class Gi Pipe. Foundation Plate ?M.S. Round Plate Of Ø 250Mm & 8 Mm Thick. Foundations Cover Cap- Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame - Made Up Of Ø 48 Mm Od ?B? Class G.I. Pipe. Handle - Made Up Of Ø48Mm Od ?B? Class G.I. Pipe. Link - Made Up Of Ø 48 Mm Od ?B? Class G.I. Pipe. Seat & Back Rest ? 380 X 275 X 60 Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Bearing Bush Closing Cap?S? Pp / Nylon / Hdpe Material. Handle Must Be Connected With Frame By 8 Mm Laser Cutting Ms Profile. Top Closing Cap ? Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Pin ? Made Up Of Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Grips - High Quality Rubber Ø 46 Mm Od. Circlips?A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271254/2025-2026 Arm And Paddle Bike - Supply And Installation Of Arm And Paddle Bike Having The Following Specifications: Dimensions: (L X W X H) 990 X 500 X 880 Mm. Main Frame &Ndash;100 Mm X 50 Mm X 2.5 Mm Rectangular Cr Pipe With Bending Design. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Round Pipe Dully Bending Design. Side And Top Cover &Ndash; 1.6 Mm Thick Ms Laser Cutting Profile Is Used. Seat &Ndash; 380 X 275 X 60 Mm Thick Hdpe Blow Moulding. Paddle &Ndash;100 Mm X 50 Mm Capsule Pipe And 40 X 16 Mm Ms Flat Should Be Used For Connecting The Paddle And Shaft. Closing Cap&Rsquo;S &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Bearing - Use Is 6005 Permanent Lubricating Sealed Reputed Brand. Shaft -Made Up Of Ø25Mm Od Ms Bright Bar. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.)

Contact Information