Supply, Installation And Maintenance Of Mechanical Compactors, Storage Systems, Furniture Articles, Solid Te ... in India

Work Detail

Supply, Installation And Maintenance Of Mechanical Compactors, Storage Systems, Furniture Articles, Solid Teak Wood Benches For Public Seating In New Judicial Complex Tower Of Justice At Gurugram-Overall Size Of Personal Locker Unit Shall Be Of Dimensions 900Mm(W) X 400Mm(D) X 1850Mm(H) Having 15 Locker Unit. Locking Shall Have Pad Lock . Material Shall Be Crca 0.8 Mm Thickness. Shelf Shall Be Uniformly Distributed Load Capacity Per Each Shelf Level Is 35 Kg Maximum. Finish Shall Be Powder Coating Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. Handle/Label Holder Shall Be Aesthetically Appealing Snap Fit Abs Plastic Handle. Ventilation Shall Be Attractive Punched Pattern For Ventilation. , Providing And Placing Workstation Table In Completely Knock Down Conditions With An Overall Size 1320Mm X 660Mm X 1200Mm That Is To Be Assembled At Site. The Work Top Shall Have The Size 1200Mm X 600Mm Made Up Of 25Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. The Profile Of The Top Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. A Pullout Keyboard Trey Shall Be Provided Of 18Mm Thick Pre-Laminated Particle Board Having Size 525Mm X 350Mm. The Trey Shall Be Operated On Keyboard Channel. The Workstation Shall Have Panel Based Partition Of 60 Mm Thick With Overall Height 1200Mm. The Partition Shall Be Linear In Profile And Provided In The Front Side Of User As Well As On The Both Sides Of The User. The Top Trim, Top Bar, Mid Bar, Vertical Bar, Raceway, Skirting Shall Be Made Up Of Aluminium Extrusions (Pre-Treated) And Duly Powder Coated With Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. The Trims Shall Have The Size 60Mm X 19Mm With 1.5Mm Thick Covered With Die Cast End Caps On Joints 2 Ways, 3 Ways And 4 Ways (L-Cover For Corner, T-Cover For Middle Section Wherever Required). The Aluminium Raceway Shall Be Situated Below The Worktop With An Overall Size 116Mm(H) X 60Mm(D) With 1.4 Mm Cover Thickness And 2Mm Back Thickness As Per Requirement Of Inlaying The Electrical Management And Carrying The Wire Horizontally. The Exposed Vertical And Horizontal Faces Of The Frames Shall Be Snap Fitted With Trims. There Shall Be Soft-Board (With Fabric) And Marker Board Provided At Front Of The User. Laminated Top Tile And Bottom Tile Shall Be Situated At Both Sides Of The User And Below The Work Top Respectively. The Partition Shall Have Concealed Wire Management Capabilities And Should Be Engaged For Responsive And Safe Operations Of Power, Telecommunications And Data (Lan) And Has Separate Components For Electrical, Data And Telephone Cables Having Adequate Capability Of Both The Vertical And Horizontal Wire Movements. Slots/Cut-Outs Should Be Given On Raceways To Fix All Electrical And Data Points. Zinc Coated Small Top Support Brackets Shall Be Fixed On The Partition For Table Top Support. To Protect The Wall From Kicks, Abrasion And Serve As A Decorative Moulding, Skirting Shall Be Situated At Bottom. Adjustable Leveller Shoe Shall Be Provided At Bottom Of The Partition To Avoid Scratches On The Floor. Fixed Type Pedestal Shall Be Provided With An Overall Size 400Mm X 450Mm X 725Mm. The Pedestal Shall Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823. Pedestal Side, Back, Top, Facia Shall Be 18Mm Thick And Drawer Base Shall Be 9Mm Thick. The Pedestal Shall Have 3 Nos. Of Drawer I.E. 2 Box Drawer And 1 Filing Drawer. The Drawer Shall Be Operated With Ss Handle And Easily Close And Open With The Assistance Of Roller Channel And Ball Bearing Channel To Enable Smooth Operation. The Drawer Shall Have Central Locking Mechanism In Which All The Drawer Shall Be Synchronized Lock With One Single Key. To Protect The Wall From Kicks, Abrasion And Serve As A Decorative Moulding, Skirting Shall Be Provided At Bottom. A Nylon Castor Based Cpu Unit Shall Be Provided With An Overall Size 468Mm X 284Mm With 18Mm Thick Pre-Laminated Particle Board. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. N , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 1200 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 1200Mm X 910Mm X 2190Mm (5 Nos) 1 Bay Single Last Movable (Lockable) 1200Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 1200 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 1200Mm X 910Mm X 2190Mm (4 Nos) 1 Bay Single Last Movable (Lockable) 1200Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 1200 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 1200Mm X 910Mm X 2190Mm (1 Nos) 1 Bay Single Last Movable (Lockable) 1200Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 2 Bay Single Static Fixed 2400Mm X 455Mm X 2190Mm (1 No.) 2 Bay Double Movable 2400Mm X 910Mm X 2190Mm (5 Nos.) 2 Bay Single Last Movable (Lockable) 2400Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 915 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 915Mm X 910Mm X 2190Mm (2 Nos) 1 Bay Single Last Movable (Lockable) 915Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 915 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 915 Mm X 910Mm X 2190Mm (1 Nos) 1 Bay Single Last Movable (Lockable) 915 Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 2 Bay Single Static Fixed 2400Mm X 455Mm X 2190Mm (1 No.) 2 Bay Double Movable 2400Mm X 910Mm X 2190Mm (4 Nos.) 2 Bay Single Last Movable (Lockable) 2400Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 1200 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 1200Mm X 910Mm X 2190Mm (2 Nos) 1 Bay Single Last Movable (Lockable) 1200Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 2 Bay Single Static Fixed 1830Mm X 455Mm X 2190Mm (1 No.) 2 Bay Double Movable 1830Mm X 910Mm X 2190Mm (4 Nos.) 2 Bay Single Last Movable (Lockable) 1830Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 2 Bay Single Static Fixed 2400Mm X 455Mm X 2190Mm (1 No.) 2 Bay Double Movable 2400Mm X 910Mm X 2190Mm (4 Nos.) 2 Bay Single Last Movable (Lockable) 2400Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 1200 Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 1200Mm X 910Mm X 2190Mm (3 Nos) 1 Bay Single Last Movable (Lockable) 1200Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 2 Bay Single Static Fixed 1830Mm X 455Mm X 2190Mm (1 No.) 2 Bay Double Movable 1830Mm X 910Mm X 2190Mm (3 Nos.) 2 Bay Single Last Movable (Lockable) 1830Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 4 Bay Single Static Fixed 4800Mm X 455Mm X 2190Mm (1 No.) 4 Bay Double Movable 4800Mm X 910Mm X 2190Mm (4 No.) 4 Bay Single Last Movable (Lockable) 4800Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 4 Bay Single Static Fixed 4800Mm X 455Mm X 2190Mm (1 No.) 4 Bay Double Movable 4800Mm X 910Mm X 2190Mm (5 No.) 4 Bay Single Last Movable (Lockable) 4800Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm (2080 Body Plus 65 Undercarriage). The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated.Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 1 Bay Single Static Fixed 915Mm X 455 Mm X 2190 Mm (1 No.) 1 Bay Double Movable 915Mm X 910Mm X 2190Mm (3 Nos) 1 Bay Single Last Movable (Lockable) 915Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm . The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 3 Bay Single Static Fixed 3600Mm X 455Mm X 2190Mm (1 No.) 3 Bay Double Movable 3600Mm X 910Mm X 2190Mm (4 Nos.) 3 Bay Single Last Movable (Lockable) 3600Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm . The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 3 Bay Single Static Fixed 2745Mm X 455Mm X 2190Mm (1 No.) 3 Bay Double Movable 2745Mm X 910Mm X 2190Mm (2 Nos.) 3 Bay Single Last Movable (Lockable) 2745Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm . The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 3 Bay Single Static Fixed 2745Mm X 455Mm X 2190Mm (1 No.) 3 Bay Double Movable 2745Mm X 910Mm X 2190Mm (3 Nos.) 3 Bay Single Last Movable (Lockable) 2745Mm X 455Mm X 2190Mm (1 No.) , Providing And Placing Mechanically Assisted Drive Mechanism Mobile Compactor. The Structure Shall Be Made Out Of 0.8 Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Each Unit Have 5 Loading Levels Formed By 4 Nos. Of Adjustable Shelves. Body Units Are Bolted To Undercarriage. Compactor Height From Ground Should Be 2190 Mm . The Body Including Shelves Shall Be Given Antirust Surface Treatment And Powder Coated With Epoxy Polyester Powder Coating I.E. Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. It Shall Have Max. Load Bearing Capacity Of 60 Kg Uniformly Distributed Per Shelf. Shelves Shall Be Mounted On Support Brackets And Shelf Level Can Be Adjusted. The Undercarriage Shall Be Welded Frame Made Of Hr Sheet Minimum 2.5 Mm Thick Suitably Fabricated To Take The Loads Based On Configuration. A Centralized Locking Arrangement Shall Be Provided Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together. This Arrangement Occupies A Space Of 100 Mm. Each Drive Type Units Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units When A Person Is Using Those Units. End Stoppers Are Provided At The End Of Channels To Prevent Derailment. The Nuts And Bolts Are Galvanized / Zn Plated. Movement Of Units Shall Be Achieved Mechanically Through A Drive Wheel And ‘Sprocket-Chain-Tensioner’ Arrangement Mounted Rigidly Onto Body Side. 3 Bay Single Static Fixed 3600Mm X 455Mm X 2190Mm (1 No.) 3 Bay Double Movable 3600Mm X 910Mm X 2190Mm (5 Nos.) 3 Bay Single Last Movable (Lockable) 3600Mm X 455Mm X 2190Mm (1 No.) , Providing And Supplying 2 Seater Visitor Chair With 3 Arms. The Seat And Back Shall Be Made Up Of Reinforced Pu With Ms Perforated Sheet (Sheet Thickness - 2.5Mm).Seat Weight With Pu 6Kg±0.01 And Back Shall Be 6.11Kg±0.01. The Seat Mounted On Ms Powder Coated Square Cross Beam Having Cross-Section Area 60Mm X 60Mm With 2Mm Thick (Weight = 3.82Kg±0.01) Fitted With Polypropylene End Caps On Both Side. The Arm (Weight = 1.28±0.01) And Leg (Weight = 1.91±0.01) Shall Be Made Up Of Pressure Diecast Aluminium. There Shall Be Leveller Shoe Provided At The Bottom With Metal Insert. The Individual Seat Size Shall Be 515±10 Mm(W) X 505±10 Mm(D), Back Size Shall Be 515±10 Mm(W) X 510Mm±10 Mm(H) From Seat, Overall Depth Shall Be 660±10 Mm, Overall Height Shall Be 870±10 Mm And Overall Width Shall Be 1100 ±10 Mm. Total Weight = 36.8 Kg±0.01. (Seat Weight Without Pu 4.6Kg±0.01 And Back Shall Be 5.0Kg±0.01.). Colour Of Pu Shall Be Tan Brown And Powder Coating Shall Be Interpol 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. , Providing And Supplying 3 Seater Visitor Chair With 4 Arms. The Seat And Back Shall Be Made Up Of Reinforced Pu With Ms Perforated Sheet (Sheet Thickness - 2.5Mm).Seat Weight With Pu 6Kg±0.01 And Back Shall Be 6.11Kg±0.01. The Seat Mounted On Ms Powder Coated Square Cross Beam Having Cross-Section Area 60Mm X 60Mm With 2Mm Thick (Weight = 5.65Kg±0.01) Fitted With Polypropylene End Caps On Both Side. The Arm (Weight = 1.28±0.01) And Leg (Weight = 1.91±0.01) Shall Be Made Up Of Pressure Diecast Aluminium. There Shall Be Leveller Shoe Provided At The Bottom With Metal Insert. The Individual Seat Size Shall Be 515±10 Mm(W) X 505±10 Mm(D), Back Size Shall Be 515±10 Mm(W) X 510Mm±10 Mm(H) From Seat, Overall Depth Shall Be 660±10 Mm, Overall Height Shall Be 870±10 Mm And Overall Width Shall Be 1625 ±10 Mm. Total Weight = 55Kg±0.01. (Seat Weight Without Pu 4.6Kg±0.01 And Back Shall Be 5.0Kg±0.01.). Colour Of Pu Shall Be Tan Brown And Powder Coating Shall Be Interpol 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. , Providing And Supplying 4 Seater Visitor Chair With 5 Arms. The Seat And Back Shall Be Made Up Of Reinforced Pu With Ms Perforated Sheet (Sheet Thickness - 2.5Mm).Seat Weight With Pu 6Kg±0.01 And Back Shall Be 6.11Kg±0.01. The Seat Mounted On Ms Powder Coated Square Cross Beam Having Cross-Section Area 60Mm X 60Mm With 2Mm Thick (Weight = 7.56Kg±0.01) Fitted With Polypropylene End Caps On Both Side. The Arm (Weight = 1.28±0.01) And Leg (Weight = 1.91±0.01) Shall Be Made Up Of Pressure Diecast Aluminium. There Shall Be Leveller Shoe Provided At The Bottom With Metal Insert. The Individual Seat Size Shall Be 515±10 Mm(W) X 505±10 Mm(D), Back Size Shall Be 515±10 Mm(W) X 510Mm±10 Mm(H) From Seat, Overall Depth Shall Be 660±10 Mm, Overall Height Shall Be 870±10 Mm And Overall Width Shall Be 2175 ±10 Mm. Total Weight = 73.2Kg±0.01. (Seat Weight Without Pu 4.6Kg±0.01 And Back Shall Be 5.0Kg±0.01. Colour Of Pu Shall Be Tan Brown And Powder Coating Shall Be Interpol 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. , Providing And Supplying A High Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat And Back Frame Shall Be Made Up Of The Combination Of 15Mm Thick Hot Pressed Commercial Plywood And Ply-Board Padded With High Resilience Polyurethane Foam (50 Plus 25 Plus 30)Mm Thick Having Density (40, 32 And 32)Kg/M³ In Seat And (30 Plus 25)Mm Thick Having Density (32, 32)Kg/M³ In Back. The Same Shall Be Upholstered With Leatherite Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine For Lumbar Support Which Helps To Provide Full Back Support As Well As Head Support. Seat And Back Shall Be Covered With Polished Wooden At Both Side For Decorative Appearance. The Chair Shall Be Supplied With Natural Wood Arm Having Melamine Polish And Die Cast Aluminium End Caps. For Seating Durability The Chair Shall Have Torsion Bar 360 Degree Revolving Mechanism With Upright Position Locking And Tilt Tension Adjustment. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 65Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Should Have Metal Insert Crca Covered With Natural Wood Having Pitch Circle Dia. 630 Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chair Should Be Injection Moulded In Black 30% Glass Filled Nylon, Confirming To Ansi/Bifma Standards X5.1-2011 To Be Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 510±10 Mm(D) X 510±10 Mm(W) And Back Size Shall Be 525±10 Mm(W) X 710±10 Mm(H) From Seat. Overall Height Shall Be = 1170±10 Mm And Overall Width/Depth = 740±10 Mm. , Providing And Supplying A High Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat Shall Be Made Of 15Mm Thick Hot Pressed Commercial Plywood Padded With High Resilience Polyurethane Foam (50 Plus 25)Mm Thick Having Density 40Kg/M³ And The Back Shall Be Made Of (15 Plus 6)Mm Thick Double Layered Moulded Plywood Padded With High Resilience Polyurethane Foam 40Mm Thick Having Density 32Kg/M³. The Seat And Back Shall Be Upholstered With Leatherite Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine Which Helps To Provide Full Back Support As Well As Head Support. The Chair Shall Be Supplied With Aluminum With Cushion Arm Having Leatherite Top Completely Joint With Seat. For Seating Durability The Chair Shall Have Synchro Knee Tilt 360 Degree Revolving Mechanism With Four Position Locking And Tilt Tension Adjustment Which Provides Back Strength For The Chair. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 65Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Should Have Five Legged Made Of Die Cast Aluminium Having Pitch Circle Dia. 700 Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chair Should Be Injection Moulded In Black 30% Glass Filled Nylon, Confirming To Ansi/Bifma Standards X5.1-2011 Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 500±10 Mm(D) X 530±10 Mm(W) And Back Size Shall Be 540±10 Mm(W) X 750±10 Mm(H) From Seat. Overall Height Shall Be = 1210±10 Mm, Overall Depth = 630±10 Mm And Overall Width = 650±10 Mm. N , Providing And Supplying A High Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat Shall Be Made Of 15Mm Thick Hot Pressed Commercial Plywood Padded With High Resilience Polyurethane Foam (50 Plus 25)Mm Thick Having Density 40Kg/M³ And The Back Shall Be Made Of (15 Plus 6)Mm Thick Double Layered Moulded Plywood Padded With High Resilience Polyurethane Foam 40Mm Thick Having Density 32Kg/M³. The Seat And Back Shall Be Upholstered With Pure Leather Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine Which Helps To Provide Full Back Support As Well As Head Support. The Chair Shall Be Supplied With Aluminum With Cushion Arm Having Leatherite Top Completely Joint With Seat. For Seating Durability The Chair Shall Have Synchro Knee Tilt 360 Degree Revolving Mechanism With Four Position Locking And Tilt Tension Adjustment Which Provides Back Strength For The Chair. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 65Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Should Have Five Legged Made Of Die Cast Aluminium Having Pitch Circle Dia. 700 Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chair Should Be Injection Moulded In Black 30% Glass Filled Nylon, Confirming To Ansi/Bifma Standards X5.1-2011 Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 500±10 Mm(D) X 530±10 Mm(W) And Back Size Shall Be 540±10 Mm(W) X 750±10 Mm(H) From Seat. Overall Height Shall Be = 1210±10 Mm, Overall Depth = 630±10 Mm And Overall Width = 650±10 Mm. , Providing And Supplying A Medium Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat And Back Frame Shall Be Made Up Of The Combination Of 15Mm Thick Hot Pressed Commercial Plywood And Ply-Board Padded With High Resilience Polyurethane Foam (50 Plus 25 Plus 30)Mm Thick Having Density (40, 32 And 32)Kg/M³ In Seat And (30 Plus 25)Mm Thick Having Density (32, 32)Kg/M³ In Back. The Same Shall Be Upholstered With Leatherite Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine For Lumbar Support Which Helps To Provide Full Back Support. Seat And Back Shall Be Covered With Polished Wooden At Both Side For Decorative Appearance. The Chair Shall Be Supplied With Natural Wood Arm Having Melamine Polish And Die Cast Aluminium End Caps. For Seating Durability The Chair Shall Have Torsion Bar 360 Degree Revolving Mechanism With Upright Position Locking And Tilt Tension Adjustment. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 65Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Should Have Metal Insert Crca Covered With Natural Wood Having Pitch Circle Dia. 630 Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chair Should Be Injection Moulded In Black 30% Glass Filled Nylon, Confirming To Ansi/Bifma Standards X5.1-2011 And Should Be Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 510±10 Mm(D) X 510±10 Mm(W) And Back Size Shall Be 525±10 Mm(W) X 560±10 Mm(H) From Seat. Overall Height Shall Be = 1010±10 Mm, Overall Depth = 680±10 Mm And Overall Width/Depth = 740±10 Mm. , Providing And Supplying A Medium Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat Shall Be Made Of 15Mm Thick Hot Pressed Commercial Plywood And The Back Shall Be Supplied With Metal Pipe, Inserted Between Backrest. The Chair Shall Be Padded With High Resilience Polyurethane Foam 50Mm Thick Having Density 40Kg/M³ In Seat And 12Mm Thick Having Density 23Kg/M³ In Back. The Seat And Back Shall Be Upholstered With Leatherite Tapestry 0.8±0.1 Mm Thick And 535 Gsm And Breathable Mesh Tapestry Behind The Backrest.. Ms Chrome Plated Pipe Frame Shall Be Provided On Both Side Of Seat And Back With Size 25Mm X 10Mm. The Backrest Shall Be Supplied By Keeping The Natural Curvature Of The Spine Which Helps To Provide Full Back Support. The Armrest Shall Be Used Black Integral Polyurethane Arm Mounted On Crca Chrome Plated Pipe Having Size 40Mm X 10Mm Completely Joint With Seat And Back With The Assistance Of Allen Key Screw. A Chrome Plated Round Bend Pipe Of Dia. 9Mm Shall Be Provided Behind The Backrest Of The Chair And Welded With Main Frame. For Seating Durability The Chair Shall Have Knee Tilt 360 Degree Revolving Mechanism With Four Position Locking And Tilt Tension Adjustment Which Provides Back Strength For The Chair. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 100Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Shall Have Five Legged Crca Chrome Plated Having Pitch Circle Dia. 640Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chairs Should Be Injection Moulded In Black 30% Glass Filled, Confirming To Ansi/Bifma Standards X5.1-2011 Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 490±10 Mm(W) X 520±10 Mm(D) And Back Size Shall Be 450±10 Mm(W) X 535±10 Mm(H) From Seat And Overall Height = 980±10 Mm, Overall Width/Depth = 740±10 Mm. , Providing And Supplying A Medium Back Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat Shall Be Made Of 15Mm Thick Hot Pressed Commercial Plywood Padded With High Resilience Polyurethane Foam (50 Plus 25)Mm Thick Having Density 40Kg/M³ And The Back Shall Be Made Of (15 Plus 6)Mm Thick Double Layered Moulded Plywood Padded With High Resilience Polyurethane Foam 40Mm Thick Having Density 32Kg/M³. The Seat And Back Shall Be Upholstered With Pure Leather Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine Which Helps To Provide Full Back Support. The Chair Shall Be Supplied With Chrome Plated With Cushion Arm Having Leatherite Covering Top Completely Joint With Seat. For Seating Durability The Chair Shall Have Synchro Knee Tilt 360 Degree Revolving Mechanism With Four Position Locking And Tilt Tension Adjustment Which Provides Back Strength For The Chair. The Pneumatic Seat Height Adjustment For Healthy Seating, User Can Adjust Seat Height Up To 65Mm With Bifma Standard Class-3 Gas-Lift To Suit Them Using The Lever Under The Seat. The Gas-Lift Mechanism Should Be Tested As Per Ansi/Bifma X5.1-2011 Standards. The Pedestal Should Have Five Legged Made Of Die Cast Aluminium Having Pitch Circle Dia. 700 Mm Fitted With 5 Nos. Twin Wheel Castors. The Castors Of The Chair Should Be Injection Moulded In Black 30% Glass Filled Nylon, Confirming To Ansi/Bifma Standards X5.1-2011Tested To Perform 98,000 Cycles With 250Lbs Load. The Seat Size Shall Be 500±10 Mm(D) X 530±10 Mm(W) And Back Size Shall Be 525±10 Mm(W) X 580±10 Mm(H) From Seat. Overall Height Shall Be = 1040±10 Mm, Overall Depth = 620±10 Mm And Overall Width = 620±10 Mm. , Providing And Supplying A Visitor Chair With Ergonomic Design For User Comfort And Shall Have Aesthetically Appealing. The Seat Shall Be Made Of 15Mm Thick Hot Pressed Commercial Plywood And The Back Shall Be Supplied With Metal Pipe, Inserted Between Backrest. The Chair Shall Be Padded With High Resilience Polyurethane Foam 50Mm Thick Having Density 40Kg/M³ In Seat And 12Mm Thick Having Density 23Kg/M³ In Back. The Seat And Back Shall Be Upholstered With Leatherite Tapestry 0.8±0.1Mm Thick, 535 Gsm And Breathable Mesh Tapestry Behind The Backrest. Ms Chrome Plated Pipe Frame Shall Be Provided On Both Side Of Seat And Back With Size 25Mm X 10Mm. The Backrest Shall Be Supplied By Keeping The Natural Curvature Of The Spine Which Helps To Provide Back Support. The Armrest Shall Be Used Black Integral Polyurethane Arm Mounted On Crca Chrome Plated Pipe Having Size 40Mm X 10Mm Completely Joint With Seat And Back With The Assistance Of Allen Key Screw. Chrome Plated Round Bend Pipe Of Dia. 9Mm Shall Be Provided Behind The Backrest Of The Chair And Welded With Main Frame. The Frame Structure Shall Be Cantilever Support Type Made Of Ms Crca Chrome Plated Round Pipe Of Dia. 25.4Mm With 2Mm Thick. There Shall Be Ppcp Shoe Provided At The Base To Avoid Scratches On The Floor. The Seat Size Shall Be 500±10 Mm(W) X 510±10 Mm(D) And Back Size Shall Be 450±10 Mm(W) X 540±10 Mm(H) From Seat And Overall Height = 980±10 Mm, Overall Width = 560±10 Mm. N , Providing And Supplying A Visitor Chair With Ergonomic Design, Comfortable And Aesthetically Appealing. The Seat And Back Frame Shall Be Made Up Of The Combination Of 15Mm Thick Hot Pressed Commercial Plywood And Ply-Board Padded With High Resilience Polyurethane Foam (50 Plus 25 Plus 30)Mm Thick Having Density (40, 32 And 32)Kg/M³ In Seat And (30 Plus 25)Mm Thick Having Density (32, 32)Kg/M³ In Back. The Same Shall Be Upholstered With Leatherite Tapestry 0.8Mm Thick And 535 Gsm. The Backrest Shall Be Made By Keeping The Natural Curvature Of The Spine For Lumbar Support Which Helps To Provide Full Back Support. Seat And Back Shall Be Covered With Polished Wooden At Both Side For Decorative Appearance. The Chair Shall Be Supplied With Natural Wood Arm Having Melamine Polish And Die Cast Aluminium End Caps. The Frame Structure Shall Be Cantilever Support Type Made Of Ms Crca Chrome Plated Round Pipe Of Dia. 28.5Mm With 2Mm Thick. There Shall Be Ppcp Shoe Provided At The Base To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 510±10 Mm(W) And Back Size Shall Be 525±10 Mm(W) X 560±10 Mm(H) From Seat. Overall Height Shall Be = 1010±10 Mm, , Providing And Supplying Centre Table With An Overall Size 1200Mm X 1200Mm X 410Mm. The Top Should Be Made Up Of 75Mm Thick, It Would Be 25Mm At Mid And 75Mm At Sides. The Mdf Top Should Have Decorative Finish With Veneer And Pu Polish And Shade As Per Directions Of Engineer-In-Charge. The Understructure Shall Consist Of 4 Nos. Of Ms Sheet Gold Leg With 6Mm Thick. , Providing And Supplying Centre Table With An Overall Size 600Mm X 600Mm X 410Mm. The Top Should Be Made Up Of 75Mm Thick, It Would Be 25Mm At Mid And 75Mm At Sides. The Mdf Top Should Have Decorative Finish With Veneer And Pu Polish And Shade As Per Directions Of Engineer-In-Charge. . The Understructure Shall Consist Of 4 Nos. Of Ms Sheet Gold Leg With 6Mm Thick. , Providing And Supplying Kids Chair. The Complete Structure Shall Be Made Up Of One Piece Injection Moulded Polypropylene Shell. The Understructure Shall Consist Of Four Legs.There Is A Square Hole On The Backrest Of Size L 140 Mm X H 50 Mm For Air Flow.The Chair Is A Single Piece Unit Made From Virgin Grade Material. The Seat Size Shall Be 280±10 Mm(W) X 300±10 Mm(D) And Back Size Shall Be 310±10 Mm(W) X 330±10 Mm(H) From Seat And Overall Height = 610±10 Mm, Overall Depth = 420±10 Mm, Overall Width = 370±10 Mm.Seat Height = 330±10 Mm The Leg Dimension Is 47 Mm X 37 Mm, L Shaped. , Providing And Supplying Visitor Chair With Ergonomic Design For User Comfort. The Seat And Back Shall Be Made Of Hot Pressed Commercial Plywood Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. The Same Shall Be Upholstered With Leatherite Tapestry 0.8Mm Thick. The Backrest Of The Chair Shall Be Made By Keeping The Natural Curvature Of The Spine For Lumbar Support With The Assistance Of Cushion. The Armrest Shall Be Of Chrome Plated Frame Padded With Cushion With Leatherite Covering On Top. The Frame Structure Shall Be Cantilever Support Type Made Up Of Ms/Crca Chrome Plated Pipe Having Cross Section 40Mm X 20Mm. There Shall Be Co-Polymer Polypropylene Shoe Provided At The Base To Avoid Scratches On The Floor As Well As Uneven Surfacing. The Seat Size Shall Be 500±10 Mm(W) X 500±10 Mm(D) And Back Size Shall Be 490±10 Mm(W) X 550±10 Mm(H) From Seat And Overall Height = 960±10 Mm, Overall Width = 600±10 Mm And Overall Depth = 670±10 Mm. N , Providing, Placing And Installing A Slotted Angle Rack With An Overall Size 900Mm (W) X 600Mm (D) X 1800Mm (H). The Panel Shall Have 5 Nos. Of Shelves Made Up Of 0.8Mm Thick High Yield Strength Crca Sheet Of Grade ‘D’ Confirming To Is: 513. Crca Slotted Angle Shall Be Supplied With 2Mm Thick Having Size 40Mm X 40Mm. All Steel Components Shall Be Have Finishing With Powder Coating Of Interpon 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. Corner Plate (Gussets) And Fasteners Shall Be Provided For Complete Assembly. , Providing, Supplying And Placing In Position An Indoor Chair Complete In All Respects Manufactured Using 20% Glass-Filled Injection Moulded Polypropylene, Ensuring High Strength, Durability, And Resistance To Wear And Tear. The Chair Shall Be Of Single-Piece Moulded Construction With A Smooth Finish And Free From Any Sharp Edges Or Defects. The Frame Structure Shall Be Supported By Four Sturdy Polypropylene Legs Of Tapered Design, Having A Diameter Of 35 Mm At The Upper End And 25 Mm At The Lower End, Providing Adequate Stability And Load-Bearing Capacity. The Seat Size Shall Be 420 ± 10 Mm (Depth) × 460 ± 10 Mm (Width), And The Back Size Shall Be 395 ± 10 Mm (Width) × 360 ± 10 Mm (Height From Seat Level), Ergonomically Designed For Comfortable Seating Posture. The Overall Height Of The Chair Shall Be 790 ± 10 Mm And Overall Depth Shall Be 515 ± 10 Mm. The Chair Shall Have A Uniform Finish, Be Uv Stabilized, And Suitable For Long-Term Use. Colour Shall Be As Approved By The Department/Engineer-In-Charge. The Rate Shall Include Supplying, Transporting, And Placing The Chair At Site In Complete Condition. Sample Shall Be Submitted For Prior Approval Before Bulk Supply. , Providing, Supplying And Placing Steel Almirah In Perfectly Upright And Straight Position. The Overall Size Of The Almirah Shall Be 915Mm (W) X 485Mm (D) X 1980Mm (H) Including Legs. It Should Be Supplied With 4 Nos. Of Adjustable Shelves I.E. 5 Loading Compartments. All Components Shall Be Made Of 0.8Mm Thick High Yield Strength Crca Sheet Of Grade ‘D’ Confirming To Is: 513. Stiffeners Shall Be Provided In Shelf And Door. The Steel Hinged Door Shall Be Provided With Locking Mechanism Which Is Assembled With Bolt Arrangement. The Shelves Shall Have Folded Constructions Which Have Intrinsic Rigidity And High Load Carrying Capacity. Uniformly Distributed Load Capacity Per Each Shelf Shall Be 40Kg Maximum. The Complete Steel Structure Shall Be Constructed By Welding And Provide Finishing With Powder Coating Of Interpol 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. , Supplying And Placing A Modular Table With An Overall Size 1350Mm X 900Mm X 750Mm. The Top Of The Table Shall Be Made Of 18Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. The Profile Of The Top Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Top Shall Be Supported On Ms Crca Powder Coated Rectangle Pipe Frame Having Cross-Section Area 50Mm X 25Mm With 1.2Mm Thick. The Table Understructure Shall Be Supplied With Ms Powder Coated Round Leg Pipe 63 X 1.2Mm. The Gable End Shall Be Given At One Side Made Up Of 0.8Mm Thick High Yield Strength Crca Sheet Of Grade `D` Confirming To Is:513. Fixed Pedestal Unit Shall Be Supplied With 1 Nos. Of Drawer Plus 1 Filing At One Side. Facia Of Drawer And Filling In 18Mm Plpb Board The Drawer Shall Be Synchronized Locked With Central Locking Mechanism By One Single Key. The Drawer Shall Be Operated With Aluminium Recessed Handle. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. Finishing With Powder Coating Of Interpol 700 Ral 9002 Ec150N Semi Glossy Of Thickness 60?-80?. , Supplying And Placing Cafeteria Table With An Overall Size 1400Mm X 900Mm X 720Mm. The Top Of The Table Shall Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminated. The Top Profile Shall Be In Rectangle Shape With Round Corner And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Top Shall Be Supported On Ms Powder Coated Pipe Frame Having Size 40Mm X 20Mm With 1.6Mm Thick. The Legs Shall Have The Combination Of Ms Powder Coated And Chrome Plated. The Joints Shall Be Made By Using Tig Welding. There Shall Be Adjustable Leveler Provided With Metal Insert At Bottom To Avoid Scratches On The Floor. , Supplying And Placing Center Table With An Overall Size 1200Mm X 1200Mm X 450Mm. The Top Shall Be Made Up Of 12Mm Thick Toughened Glass. The Top Profile Shall Be In Rectangle Shape With Bevelled Edges. The Top Shall Be Supported On Vacuum Caps Situated Over Ss 202 Grade Pipe Frame. A Hanging Storage Shelf Shall Be Provided Below The Top Of Ss With An Overall Size 820Mm X 390Mm With The Assistance Of 31 Nos. Small Round Strips Having 5Mm Dia.The Under Structure Shall Have Ss 202 Grade Pipe Frame Having Size 30Mm X 10Mm. 2 Nos. Foot Step Shall Be Provided Between The Pipe Frame With Size 30Mm X 10Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. N , Supplying And Placing Center Table With An Overall Size 1200Mm X 600Mm X 450Mm. The Top Shall Be Made Up Of 12Mm Thick Toughened Glass. The Top Profile Shall Be In Rectangle Shape With Bevelled Edges. The Top Shall Be Supported On Vacuum Caps Situated Over Ss 202 Grade Pipe Frame. A Hanging Storage Shelf Shall Be Provided Below The Top Of Ss With An Overall Size 820Mm X 390Mm With The Assistance Of 31 Nos. Small Round Strips Having 5Mm Dia. The Under Structure Shall Have Ss 202 Grade Pipe Frame Having Size 30Mm X 10Mm. 2 Nos. Foot Step Shall Be Provided Between The Pipe Frame With Size 30Mm X 10Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. N , Supplying And Placing Center Table With An Overall Size 600Mm X 600Mm X 450Mm. The Top Of The Table Shall Be Made Up Of 12Mm Thick Toughened Glass. The Top Profile Shall Be In Square Shape And The Edges Shall Be In Chamfer Shape. The Top Shall Be Supported On Vacuum Caps Situated Over Ss 202 Grade Pipe Frame. A Hanging Storage Shelf Shall Be Provided Below The Top Of Ss With An Overall Size 270Mm X 390Mm With The Assistance Of 9 Nos. Small Round Strips Having 5Mm Dia. And 370Mm Length. The Under Structure Shall Have Ss With Shiny Chrome Finish Pipe Frame Having Size 30Mm X 10Mm. 2 Nos. Foot Step Shall Be Provided Between The Pipe Frame With Size 30Mm X 10Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. , Supplying And Placing Conference Table In Completely Knock Down Conditions With An Overall Size 1500Mm X 750Mm X 750Mm That Is To Be Assembled At Site. The Work Top Shall Have The Size 1500Mm X 750Mm Made Up Of 45Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Laminate And Finish As Per Shade Approved By Engineer-In-Charge. The Top Profile Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The End Wall Of The Table On The Side Shall Be Topped By Gable End. The Gable End Shall Be Made Up Of 18Mm Thick Pre-Laminated Particle Board And Profile Shall Be In Linear Shape With Extruded Aluminium Profile Shall Be Attached On The Both Side Front And Back Side Of The Gable Ends And Bottom Side Appropriate Pvc Edge Banding. The Table Shall Be Clad With 18Mm Thick Modesty Panel Which Provide Structural Support For The Table. It Should Be 18Mm Thick Pre-Laminated Particle Board Of Height 600Mm In Linear Shape With Appropriate Pvc Edge Banding Connected With Both End. There Shall Be Buffers Provided At The Base To Avoid Scratches On The Floor. , Supplying And Placing Conference Table In Completely Knock Down Conditions With An Overall Size 2100Mm X 900Mm X 750Mm That Is To Be Assembled At Site. The Construction Of The Main Table Shall Be Free Standing Structure Constructed With The Help Of Minifix Dowels And Pins. The Table Top Shall Have The Size 2100Mm X 900Mm Made Up Of 50Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With One Side Laminate And Finish As Per Approved Shade. The Table Top Profile Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edgebander Machine At 200 0C. The Table Top Shall Be Supported By Particle Board Base Gable End. The End Wall Of The Table On The Side Shall Be Topped By Gable End. The Gable End Shall Have The Size 1050Mm X 695Mm With 49Mm Thick And 100Mm X 695Mm With 18Mm Thick. The Gable End Shall Be Made Up Of Pre-Laminated Particle Board With Appropriate Pvc Edge Banding And Covered Both Side By Aluminium Section. The Table Shall Be Clad With 18Mm Thick Modesty Panel Which Provide Structural Support For The Desk. The Modesty Panel Shall Have An Overall Size 1400Mm X 400Mm With 18Mm Thick Pre-Laminated Particle Board With Appropriate Pvc Edge Banding Connected With Both End. There Shall Be Buffers Provided To Avoid Scratches On The Floor. The Table Connections Have To Be Made In Such A Way That No Gap Should Be Seen In Between. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. , Supplying And Placing Conference Table In Completely Knock Down Conditions With An Overall Size 7200Mm X 1200Mm X 750Mm That Is To Be Assembled At Site. The Construction Of The Main Table Shall Be Free Standing Structure Constructed With The Help Of Minifix Dowels And Pins. The Table Top Shall Be Made Up Of 25Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. The Table Top Profile Shall Be In Rectangle Shape With Round Front And Back And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Table Shall Be Supported On Particle Board Base Gable End. The End Wall Of The Table On The Side Shall Be Topped By Gable End.It Should Be Made Up Of 25Mm Thick Pre-Laminated Particle Board And Profile Shall Be In Linear Shape With Full Round Post Form And Other Edges Sealed With Appropriate Pvc Edge Banding. The Table Shall Be Clad With 18Mm Thick Modesty Panel Which Provide Structural Support For The Table. It Should Be 18Mm Thick Pre-Laminated Particle Board With Appropriate Pvc Edge Banding Connected With Both End. There Shall Be Buffers Provided At The Base To Avoid Scratches On The Floor. The Table Connections Have To Be Made In Such A Way That No Gap Should Be In Between.The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. , Supplying And Placing Conference Table In Completely Knock Down Conditions With An Overall Size Dia. 1200Mm X 750Mm That Is To Be Assembled At Site. The Table Top Shall Be Made Up Of 25Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. The Table Top Profile Shall Be In Circular Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Table Shall Be Supported On Ms Powder Coated Round Pipe Having 50Mm Dia With 1.6Mm Thickness And Over Particle Board Gable End Of 18Mm Thickness. The Table Understructure Shall Have 4 Nos. Of Legs. The Table Is Provided With 8Mm Thick Bottom Plate And 5 Mm Thick Top Plate. There Shall Be Gliders Provided At The Base To Avoid Scratches On The Floor. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. N , Supplying And Placing Conference Table In Completely Knock Down Conditions With Per Seat Size 675Mm X 600Mm X 750Mm That Is To Be Assembled At Site. The Construction Of The Main Table Shall Be With Minifix Dowels, Pins And Ms Brackets. The Top Shall Be Made Up Of 25Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. The Top Profile Shall Be In C Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Table Top Shall Be Supported On Particle Board Base Gable End. The End Wall Of The Table On The Side Shall Be Topped By Gable End. It Should Be Made Up Of 25Mm Thick Pre-Laminated Particle Board And The Profile Shall Be In Linear Shape With Appropriate Pvc Edge Banding. The Table Shall Be Clad With 18Mm Thick Modesty Panel Which Provide Structural Support For The Table. The Modesty Panel Shall Be 18Mm Thick Pre-Laminated Particle Board With Appropriate Pvc Edge Banding Connected With Both End. There Shall Be Buffers Provided At The Base To Avoid Scratches On The Floor. The Table Connections Have To Be Made In Such A Way That No Gap Should Be Seen In Between. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380 , Supplying And Placing Corner Table With An Overall Size 1200Mm X 600Mm X 450Mm. The Top Of The Table Shall Be Made Of 18Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823. The Top Profile Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Understructure Shall Consist Of Ss 202 Grade Pipe Frame With Shiny Chrome Finish With An Overall Size The Size 40Mm X 20Mm With 1.6Mm Thick. One Nos. Footstep Shall Be Provided Between The Frame With Same Size I.E. 40Mm X 20Mm. There Shall Be Ppcp Shoe Provided At The Bottom To Avoid Scratches On The Floor. , Supplying And Placing Modular Table In Completely Knock Down Conditions With An Overall Size 1800Mm X 1650Mm X 750Mm That Is To Be Assembled At Site. The Work Top Shall Have The Size 1800Mm X 750Mm Made Up Of 50Mm Thick Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Laminate I.E. Merino Luvih Antique Walnut 37380. The Top Shall Be 50Mm Thick On Edges, After 100Mm From Edges It Should Be 25Mm Thick. The Top Profile Shall Be In Rectangle Shape And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. Extruded Aluminium Profile Shall Be Inserted In The Side Edges Of The Table On Both Side. The Table Top Shall Be Supported On Ms Powder Coated Pipe Frame Having Cross-Section Area 50Mm X 25Mm With 1.6Mm Thick. The End Wall Of The Table On The Side Shall Be Topped By Gable End. The Gable End Shall Be Made Up Of 50Mm Thick Pre-Laminated Particle Board And Profile Shall Be In Linear Shape With Appropriate Pvc Edge Banding. The Table Shall Be Clad With 18Mm Thick Modesty Panel Which Provide Structural Support For The Table. It Should Be 18Mm Thick Pre-Laminated Particle Board In Linear Shape With Appropriate Pvc Edge Banding Connected With Both End. The Table Shall Have Side Unit For Storage Purpose With An Overall Size 900Mm X 450Mm X 750Mm. The Storage Shall Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Laminate I.E. Merino Luvih Antique Walnut 37380. The Top Shall Be 25Mm Thick And All Other Profile I.E. Side, Back, Shutter, Shelf, Skirting Shall Be 18Mm Thick. The Edges Shall Be Sealed With Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Storage Shall Have 1 Nos. Of Adjustable Shelf And 2 Nos. Of Door Shutters Shall Be Provided For Opening And Closing The Storage. The Shutter Shall Be Operated With Concealed Crank Hinge With Al Die Cast Handle As Well As Mp Lock Mechanism. To Protect The Wall From Kicks, Abrasion And Serve As A Decorative Moulding, Skirting Shall Be Provided At Bottom. There Shall Be Buffers Provided At The Bottom To Avoid Scratches On The Floor. A Mobile Pedestal Shall Be Provided With An Overall Size 400Mm X 450Mm X 680Mm. The Pedestal Shall Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823. Pedestal Side, Back, Top, Facia Shall Be 18Mm Thick And Drawer Base Shall Be 9Mm Thick. The Pedestal Shall Have 3 Nos. Of Drawer I.E. 2 Box Drawer And 1 Filing Drawer. The Drawer Shall Be Operated With Ss Handle And Easily Close And Open With The Assistance Of Roller Channel And Ball Bearing Channel To Enable Smooth Operation. The Drawer Shall Have Central Locking Mechanism In Which All The Drawer Shall Be Synchronized Locked With One Single Key. The Pedestal Shall Be Mounted Over 50Mm Injection Moulded Nylon Castor. All The Size Shall Have The Tolerance Of Upper And Lower Deviation Of ±10Mm For Board And ±0.2Mm For Metal. The Board Used Should Meet International Standard Of Quality, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Rupture And Modulus Of Elasticity Bending Tested As Per Is 2380. N , Supplying And Placing Nursery Classroom Table With An Overall Size 1400Mm X 300Mm X 550Mm. The Top Of The Table Shall Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminated. The Top Profile Shall Be In Curve Shape With Round Corner And The Edges Shall Be Sealed With 2Mm Thick Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Legs Shall Have The Combination Of Ms Powder Coated And Chrome Plated With 40Mm Dia. The Joints Shall Be Made By Using Tig Welding. There Shall Be Adjustable Leveler Provided With Metal Insert At Bottom To Avoid Scratches On The Floor. , Supplying And Placing Office Table In Completely Knock Down Conditions With An Overall Size 3000Mm X 1200Mm X 750Mm That Is To Be Assembled At Site. The Worktop Shall Be Made Up Of Medium Density Fibre-Board With Veneer Laminate Of Shade As Per Engineer-In-Charge. The Top Panel Shall Be In Rectangle Shape With 79Mm Thick (75Mm Mdf Plus 4Mm Natural Veneer And Pu). Veneered Portion Of Work Surface Shall Be Finish With Pu Polish. The Edges Of The Table Shall Be Supplied With Solid Brass Bar Strips Having Cross-Section Area 25Mm X 5Mm All Around Worktop. The Top Panel Shall Be Supported On Ms/Crca Rectangle Pipe Frame Having Cross-Section Area 40Mm X 20Mm With 1.6Mm Thick. The Table Top Shall Be Enclosed With Flapper Box On Both Sides For Electric Provision Duly Polished. The End Wall Of The Table On The Side Shall Be Topped By Gable End. It Should Be 63Mm Thick Made Up Of (59Mm Mdf Plus 4Mm Natural Veneer And Pu). The Table Shall Be Clad With 29Mm Thick (25Mm Mdf Plus 4Mm Natural Veneer And Pu) Modesty Panel Which Provide Structural Support For The Table. The Profile Of The Gable End And Modesty Panel Shall Be In Linear Shape With Appropriate Veneer Surface. There Shall Be Leveler Provided With Metal Insert At The Base To Avoid Scratches On The Floor As Well As Uneven Surfacing. The Table Shall Be Supplied With Both Side Pedestal Unit With An Overall Size 600Mm X 920Mm X 590Mm. Top, Side, Back, Facia Shall Be Made Up Of 18Mm Thick Mdf Board With Approved Veneer Laminate. It Shall Have 3 Nos. Of Drawer Operated With The Assistance Of Soft Closed Ball Bearing Channel And Grooves Handle For Easy Griping. The Complete Structure Shall Be Supplied With Approved Veneer Laminate And Pu Polish Accordingly. The Table And Pedestal Have To Be Made In Such A Way That No Gap Should Be Seen In Between. All The Size Shall Have The Tolerance Of Upper And Lower Deviation Of ±10Mm For Board And ±0.2Mm For Metal. , Supplying And Placing Single Seater Sofa That Shall Be Constructed From Natural Hard Wood And Commercial Plywood Having Inner Frame. The Thickness Of The Wood Should Allow For The Heavy Tension Webbing. The Sofa Shall Have Spring Attached And Also Be Padded Separately. The Frame Shall Be Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. There Shall Be Cushion Arm Provided Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³. The Structure Shall Be Upholstered With Leatherite Tapestry 1±0.2 Mm Thick And 571 Gsm And Color As Per Direction Of Engineer In Charge. The Understructure Shall Consist Of Pipe Frame Loop Leg Of Ss Shiny Chrome Finish Having Cross-Section Area 40Mm X 20Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 540±10 Mm(W), Seat Height = 435±10 Mm, Overall Width = 915±10 Mm, Overall Depth = 770±10 Mm And Overall Height = 800±10 Mm.N , Supplying And Placing Storage Unit With An Overall Size 600Mm X 450Mm X 1800Mm. It Should Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Approved Laminate And Finish As Per Approved Shade. All Profile I.E. Side, Back, Top, Shutter, Shelf, Skirting Shall Be 18Mm Thick And The Edges Shall Be Sealed With Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Storage Shall Have Four Nos. Of Adjustable Shelf. Door Shutters Shall Be Provided For Ease Of Opening With The Assistance Of Soft Closed Concealed Crank Hinge And Leather Handle. The Front Section Of The Shutter Shall Be Supplied Ss 202 Grade Pipe Frame (Loop) Having Cross-Section Area 40Mm X 20Mm With 1.6Mm Thick. The Understructure Shall Consist Of Ss 202 Grade Leg Having Cross-Section Area 80Mm X 20Mm With 1.6Mm Thick. There Shall Be Buffers Provided At The Bottom To Avoid Scratches On The Floor. The Boards Used Should Meet International Standards Of Quality And Safety, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Elasticity Bending Tested As Per Is 2380. , Supplying And Placing Storage Unit With An Overall Size 900Mm X 450Mm X 900Mm. It Should Be Made Up Of Pre-Laminated Particle Board Of Grade Ii Of Is 12823 With Laminate I.E. Merino Luvih Antique Walnut 37380 And Finish As Per Approved Shade. All Profile I.E. Side, Back, Top, Shutter, Shelf, Skirting Shall Be 18Mm Thick And The Edges Shall Be Sealed With Thin Strip Of Impermeable Pvc That Is Cut To Fit The Size Of Board Panel And Duly Pasted With The Assistance Of Edge Banding Machine At 200 Degree Celsius. The Storage Shall Have Two Nos. Of Adjustable Shelf. Door Shutters Shall Be Provided For Ease Of Opening With The Assistance Of Soft Closed Concealed Crank Hinge And Leather Handle. The Fornt Section Of The Shutter Shall Be Supplied Ss 202 Grade Pipe Frame (Loop) Having Cross-Section Area 40Mm X 20Mm With 1.6Mm Thick. The Understructure Shall Consist Of Ss 202 Grade Leg Having Cross-Section Area 80Mm X 20Mm With 1.6Mm Thick. There Shall Be Buffers Provided At The Bottom To Avoid Scratches On The Floor. The Boards Used Should Meet International Standards Of Quality And Safety, Indian Standard Is 12823 Grade Ii Should Meet Long Time Load Bending, Screw-Withdrawal Strength, Modulus Of Elasticity Bending Tested As Per Is 2380. , Supplying And Placing Three Seater Sofa That Shall Be Constructed From Natural Hard Wood And Commercial Plywood Having Inner Frame. The Thickness Of The Wood Should Allow For The Heavy Tension Webbing. The Sofa Shall Have Spring Attached And Also Be Padded Separately. The Frame Shall Be Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. There Shall Be Cushion Arm Provided Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³. The Structure Shall Be Upholstered With Leatherite Tapestry 1±0.2 Mm Thick And 571 Gsm. The Understructure Shall Consist Of Pipe Frame Loop Leg Of Ss Shiny Chrome Finish Having Cross-Section Area 40Mm X 20Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 1540±10 Mm(W), Seat Height = 435±10 Mm, Overall Width = 1900±10 Mm, Overall Depth = 770±10 Mm And Overall Height = 800±10 Mm. N , Supplying And Placing Three Seater Sofa That Shall Be Constructed From Natural Hard Wood And Commercial Plywood Having Inner Frame. The Thickness Of The Wood Should Allow For The Heavy Tension Webbing. The Sofa Shall Have Spring Attached And Also Be Padded Separately. The Frame Shall Be Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. There Shall Be Cushion Arm Provided Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³. The Structure Shall Be Upholstered With Pure Leather Tapestry 1±0.2 Mm Thick And 571 Gsm. The Understructure Shall Consist Of Pipe Frame Loop Leg Of Ss Shiny Chrome Finish Having Cross-Section Area 40Mm X 20Mm. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 1540±10 Mm(W), Seat Height = 435±10 Mm, Overall Width = 1900±10 Mm, Overall Depth = 770±10 Mm And Overall Height = 800±10 Mm. , Supplying And Placing Two Seater Sofa That Shall Be Constructed From Natural Hard Wood And Commercial Plywood Having Inner Frame. The Thickness Of The Wood Should Allow For The Heavy Tension Webbing. The Sofa Shall Have Spring Attached And Also Be Padded. The Frame Shall Be Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. There Shall Be Cushion Arm Provided Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³. The Complete Structure Shall Be Upholstered With Leatherite Tapestry 1±0.2 Mm Thick And 571 Gsm And Color As Per Direction Of Engineer In Charge. The Understructure Shall Consist Of Ss 202 Grade Loop Leg With Shiny Chrome Finish Having Cross-Section Area 40Mm X 20Mm With 1.6Mm Thick. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 1040±10 Mm(W), Seat Height = 435±10 Mm, Overall Width = 1360±10 Mm, Overall Depth = 770±10 Mm And Overall Height = 800±10 Mm. N , Supplying And Placing Two Seater Sofa That Shall Be Constructed From Natural Hard Wood And Commercial Plywood Having Inner Frame. The Thickness Of The Wood Should Allow For The Heavy Tension Webbing. The Sofa Shall Have Spring Attached And Also Be Padded. The Frame Shall Be Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³ In Seat And 32Kg/M³ In Back. There Shall Be Cushion Arm Provided Padded With High Resilience Polyurethane Foam Having Density 40Kg/M³. The Complete Structure Shall Be Upholstered With Pure Leather Tapestry 1±0.2 Mm Thick And 571 Gsm. The Understructure Shall Consist Of Ss 202 Grade Loop Leg With Shiny Chrome Finish Having Cross-Section Area 40Mm X 20Mm With 1.6Mm Thick. There Shall Be Shoe Provided At The Bottom To Avoid Scratches On The Floor. The Seat Size Shall Be 510±10 Mm(D) X 1040±10 Mm(W), Seat Height = 435±10 Mm, Overall Width = 1360±10 Mm, Overall Depth = 770±10 Mm And Overall Height = 800±10 Mm. , Wooden Bench 2.191 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 2.2 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respect , Wooden Bench 2.242 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 2.282 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 2.494 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 2.57 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 2.703 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.022 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.024 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.025 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.1 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.182 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.192 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.34 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.386 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.5 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.559 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.58 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.621 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.7 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.895 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.922 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects. , Wooden Bench 3.929 Meter Length. The Bench Shall Be Made Up Of `1St Class Seasoned Teak Wood` And Thickness Of Wood Plank (Seat And Back) Shall Be 38Mm And Clear Depth Of Seat And Back Support Shall Be 460Mm. The Arms/Legs On Both Ends Of The Bench Shall Be 60Mm Thick Wooden Planks And There Shall Be Legs/ Supports In Between Of 38Mm Thick Wooden Plank. The Shop Drawings Of The Bench With Size Are Enclosed And Photograph Of The Bench Is Also Enclosed For Reference. The Entire Bench Is Finished With High-Quality Melamine Polish Compling With Astm D1475 And Astm D2369 Complete In All Respects.

Contact Information