|
Tender for Repair To Pot Holes And Removal Of Loose Material, Trimming Of Sides, Cleaning Of Surface By Providing Tack Coat With Bitumen Emulsion, 20 Mm Thick Pre-Mix Carpet Using Catonic Bitumen Emulsion @ 21.5 Kg Per 10 Sqm And Seal Coat Type B With Bitumen Emulsion @ 10Kg Per 10 Sqm As Per Technical Specification And Compacting With Three Wheeled 80-100 Kn Static Roller. , Repair Of Pot Holes, Patch Repair Providing, Laying And Rolling Of Built-Up-Spray Grout Layer Over Prepared Base Consisting Of Composite Construction Of Compacted Crushed Coarse Aggregates And Key Stone Chips With Application Of Bituminous Binder After Each Layer, And With Key Aggregates Placed On Top Of The Final Layer To Serve As A Base Conforming To The Line, Grades And Cross-Section Specified, (Number Of Layers Of Coarse Aggregate Shall Be As Per Site Requirement). , Wet Mix Macadam Providing, Laying, Spreading And Compacting Graded Stone Aggregate To Wet Mix Macadam Specification Includingpremixing The Material With Water At Omc In Mechanical Mix Plant Carriage Of Mixed Material By Tipper To Site, Laying In Uniform Layers With Paver In Sub- Base / Base Course On Well Prepared Surface And Compacting With Vibratory Roller To Achieve The Desired Density In Accordance To Table No. 400-12, 400-13 And As Per Clause Of Section 406 Of Specifications. , Deduction For Item No.4.3 If Sensor Paver Is Not Used. , Prime Coat Over Wmm/Wbm (I) Providing And Applying Primer Coat With Catonic Bitumen Emulsion On Prepared Surface Of Granular Base Including Cleaning Of Road Surface And Spraying Primer At The Rate Of 0.70 To 1.00 Kg/Sqm Using Mechanical Means As Per Clause 502 Of Specifications , Providing And Applying Tack Coat With Low Viscosity Bitumen Of Vg 10 Grade Using Bitumen Pressure Sprayer On The Prepared Bituminous/Granular Surface Cleaned With Mechanical Broom And As Per Relevant Clauses Of Section-503 Of Specifications. (I) @ 0.25 Kg Per Sqm (Normal Bituminous Surfaces) , (Ii) @0.30 Kg Per Sqm (Dry & Hungry Bituminoussurfaces / Granular Surfaces Treated With Primer) , Dense Graded Bituminous Macadam Providing And Laying Dense Bituminous Macadam Using Crushed Aggregates Of Specified Grading, Premixed With Bituminous Binder @ 4.0 To 4.5% By Weight Of Total Mix Of Mix And Filler, Transporting The Hot Mix To Work Site, Laying With A Electronic Sensor Paver Finisher With Sensor Control To The Required Grade, Level And Alignment, Rolling With Smooth Wheeled, Vibratory And Tandem Rollers To Achieve The Desired Compaction As Per Clause 505 Of Specification Complete In All Respects B) Using Drum Mix Plant Of Appropriate Capacity (Iv) For Grading Ii (26.5 Mm Nominal Size) Bitumen Content Minimum 4.5% With Bitumen 60/70 (Vg 30) , Bituminous Concrete Providing And Laying Bituminous Concrete Using Crushed Aggregates Of Specified Grading, Premixed With Bituminous Binder @ 5.4 To 5.6 % By Weight Of Total Mix Of Mix And Filler, Transporting The Hot Mix To Work Site, Laying With An Electronic Sensor Paver Finisher With Sensor Control To The Required Grade, Level And Alignment, Rolling With Smooth Wheeled, Vibratory Tandem And Pneumatic Tyre Rollers To Achieve The Desired Compaction As Per Clause 507 Of Specification B) Using Drum Mix Plant Of Appropriate Capacity (V) For Grading-Ii (30-40 Mm Thickness) Bitumen Content Minimum 5.4% With 60/70 Bitumen (Vg-30) , Construction Of Shoulders With Approved Material/Selected Soil I/C Excavation All Lifts & Leads I/C Grading To Required Slope & Camber Of 4% And Compacting Using Vibratory Roller Of 80 To 100 Kn Static Weight To Meet Requirement As Per Relevant Clause Of 400. (B) Hard Shoulders (Cbr Value 12) , Providing And Laying Reinforced Cement Concrete Pipe 300Mm Dia Np-4 For Service Ducts Below Concrete Pavement. A) 300 Mm Dia , B) 600 Mm Dia , Retro- Reflectorised Traffic Signs Providing And Fixing Of Retro-Reflectorised Cautionary, Mandatory And Informatory Sign Board As Per Irc 67-2012 Made Of High Intensity Micro-Prismatic Grade Sheeting (Type Xi) Vide Irc: 67:2012 Clause 6.7.3.2 And Clause 801.3.3 Of Mort&H Fixed Over Aluminum Composite Material Sheet With Thermoplastic Core Of Low Density Polyethylene (Ldpe) Between Two Thick Skins/Sheets Of Aluminum With Overall Thickness Of 4Mm And Aluminum Skin Of Thickness 0.3 On Both Side, The Acm Shall Conform To Table 6.1 Of Irc:67:2012 And Table 800-1 Of Mort&H Specification And High Intensity Micro Prismatic Grade Sheeting Shall Onform To Table 6.6 Of Irc:67:2012 And Table 800-3 Of Mort&H Specification Of In The Clause Irc 6.8 Of The Irc 67-2012 And Clause 801.3.7 Of Morth Message Legend Numerical Letter Etc. And Borders Shall Be Screen Printed On High Intensity Micro Prismatic Sheeting Shall Conform To Clause 801.3.7 With Digital Printing Ink Or Of Cutout From Transparent Durable Overlay Or Cutout From The Same Type Of Reflecting Sheeting For Cautionary/ Mandatory/ Signs, Supported On An Irc Accredited Triangular Sign Post Of Size 75Mm X 60 Mm X60 Mm (4 Mm Wall Thickness) Made Of Advance Polymer Composite Of 3.60 Meter Over All Length And Fix To Ground By Means Of Properly Designed Foundation Of Dimension 450X450x600mm With M20 Grade Concrete. The Acm Sheet Shall Be Fixed To The Post With Four Minimum Number Breakaway Bolts. & Supported With A Back Support Frame Of 25Mmx25mmx3mm Angle. 7 Years Warranty For Retro Reflection Sheeting To Be Provided From The Original Sheeting Manufacture As Per Clause 6.9 Of Irc: 67:2012 & A Certified Copy For Three Years For Out Door Exposure Report From An Independent Test Lab As Per Clause 6.7 Of Irc: 67:2012 For The Product Offered Shall Be Submitted By The Contractor Xii ) 60 Cm X 45 Cm Rectangular , 80 Cm X 60 Cm Rectangular , 60 Cm Equilateral Triangle , 60 Cm Circular , Direction And Place Identification Signs Upto 0.9 Sqm Size Board. Providing And Fixing Of Retro-Reflectorised Cautionary, Mandatory And Informatory Sign Board As Per Irc 67-2022 Made Of High Intensity Micro-Prismatic Grade Sheeting (Type Iv) Vide Irc: 67:2022 Clause 6.7.3.2 And Clause 801.3.3 Of Mort&H Fixed Over Aluminum Composite Material Sheet With Thermoplastic Core Of Low Density Polyethylene (Ldpe) Between Two Thick Skins/Sheets Of Aluminum With Overall Thickness Of 4Mm And Aluminum Skin Of Thickness 0.3 On Both Side, The Acm Shall Conform To Table 6.1 Of Irc:67:2022 And Table 800-1 Of Mort&H Specification And High Intensity Micro Prismatic Grade Sheeting Shall Conform To Table 6.6 Of Irc:67:2022 And Table 800-3 Of Mort&H Specification Of In The Clause 6.8 Of The Irc 67-2022 And Clause 801.3.7 Of Mort&H Message Legend Numerical Letter Etc. And Borders Shall Be Screen Printed On High Intensity Micro Prismatic Sheeting Shall Conform To Clause 801.3.7 With Digital Printing Ink Or Of Cutout From Transparent Durable Overlay Or Cutout From The Same Type Of Reflecting Sheeting For Cautionary/ Mandatory/ Signs, Supported On 2 Nos. Of Ms Sign Post Of Size 75Mm X75mm X 6Mm Of 3.60 Meter Over All Length And Fix To Ground By Means Of Properly Designed Foundation Of Dimension 450X450x600 Mm With M20 Grade Concrete. The Acm Sheet Shall Be Fixed To The Post With Four Minimum Four Number Breakaway Bolts. & Supported With A Backsupport Frame Of 25Mmx25mmx3mm Angle. 7 Years Warranty For Retro Reflection Sheeting To Be Provided From The Original Sheeting Manufacture Brand Like 3M/Avery Dennison/ Orafol Make As Per Clause 6.9 Of Irc: 67:2022 & A Certified Copy For Three Years For Outdoor Exposure Report From An Independent Test Lab As Per Clause 6.7 Of Irc: 67:2022 For The Product Offered Shall Be Submitted By The Contractor , Kilo Metre Stone Reinforced Cement Concrete M15grade Kilometre Stone Of Standard Design As Per Irc:8-1980, Fixing In Position Including Painting And Printing Etc (Ii) Ordinary Kilometer Stone (Precast) , Hectometer Stone (Precast) , Road Markers/Road Stud With Lense Reflector Providing And Fixing Single Mound Twin Shanked Molded Roadmarkers/Road Stud Made Of Poly Carbonate Or Abs Body And Shallsupport A Load Of 13635 Kg Tested In Accordance To Astm D 4280 And Complying Lo Specifications Of Section-5 Of Irc:35-2015 And Clause 804.2.2 Of Mort&H And Section-5 Of Irc:35-2015. He Reflecting Panels Shall Consist Of Number Of Lenses Containing Single Or Dual Prismatic Cubes Capable Of Providing Total Internal Reflection Of The Light Entering The Lens Face. The Slope Or Retro-Reflecting Surface Should Be 35 + 5 Degree To Base. The Reflective Marker Shall Be Fixed To The Road Surface Using The Epoxy/ Adhesives And The Procedure Recommended By The Manufacturer. No Nails Shall Be Used To Affix The Markers So Cubes Capable Of That They Do Not Pose Safety Hazard On The Road. The Contractor Shall Submit A Two-Year Replacement Warranty. For Satisfactory Field Performance Including Stipulated Retroreflectance Of The Reflecting Panel. (Make- 3M /Avery Dennison/ Orafol / Alcolitea / Automark) , Boundary Pillar Reinforced Cement Concrete M15 Grade Boundary Pillars Of Standard Design As Per Irc:25-1967, Fixed In Position Including Finishing And Lettering But Excluding Painting. , Road Delineators Supplying And Installation Of Delineators (Road Way Indicators, Hazard Markers, Object Markers), 80-100 Cm High Above Ground Level, Painted Black And White In 15 Cm Wide Stripes, Fitted With 80 X 100 Mm Rectangular Or 75 Mm Dia Circular Reflectorised Panels At The Top, Buried Or Pressed Into The Ground And Confirming Toirc-79 And The Drawings , Road Marking With Hot Applied Thermoplastic Compound With Reflectorising Glass Beads On Bituminous Surface Providing And Applying (Cleaning Of Bituminous Surface) Thermoplastic Compound Having Composition Of Binder (Regin) Minimum 18 %, Titanium Dioxide Minimum 10 % And Intermixed Glass Beed, Minimum 30% Of Brand Like Asian, Burger Or Equivalent Make Of 2.5 Mm Thick Including Drop Down Reflectorizing, Glass Beeds @ 250 Gms Per Sqm Area Thickness Of 2.5 Mm Is Exclusive Of Surface Applied Glass Beeds As Per Irc:35.The Finished Surface To Be Level, Uniform And Free From Streaks And Holes, All Complete As Per Clause 803 Of Specifications.
|
