|
Tender For Supplying And Erecting Of 3M Height Designer Decorative Post Top Mounting Pole Made In Combination Of Galvnizing Pipe Which Is Fabricated Using 114M Dia X 3.0Mm Thick Base Section With Minimum Height Of 600Mm, The Middle Section Is Of 76Mm (+/-3%) Dia Gi Pipe With Height Of Section Is More Than 1350Mm And The Remaining Section Is Of 60Mm (+/- 3%) Dia Gi Pipe With Height Of Section Is More Than 1050Mm. The Complete Pole Shall Be Coated With Etch Primer And Further With Epoxy Zinc Phosphate Primer & Then Painted With Environmentally Stable Polyurethane Paint (Coating Thickness - 80 Microns Minimum). The Bottom And Middle Section Of The Pole Shall Be Provided With Decorative Cast Aluminium Embellishment To Add Aesthetic On The Pole As Shown In The Drawing. The Brackets Shall Be A Single Piece Assembly And Should Be Capable Of Orientation In Any Direction And Secured With Stainless Steel 304 Grade Hardware. The Pole Is To Be Provided With A Surface Mounting Suitable Base Plate Dia Of 350Mm And Suitable Thickness As Per Is Standards And Structural Reports. Decorative Ring Between Base Pole And Bracket Is Made Of Cast Aluminium Material. The Decorative Bottom Most Base Is Made Of Single Piece Cast Aluminium Material With 9W 30K Foot Light With (Ingress Protection) Ip66 Of Lamp Compartment. (All Al Casting Should Not Be In 2 Parts With Any Vertical Cuts Which Are Then Bolted Or Welded From Centre Which Spoils The Aesthetics Of The Designer Decorative Pole) With The Company / Brand Logo Embossed On It. All Dimension Is Within +/- 5% Tolerance. The Pole Should Be Provided With An Inbuilt Junction Box To Fix Four-Way Connector And 6A Mcb At The Bottom - The Inbuilt Box Should Have A Flush Door Of Suitable Size. The Decorative Pedestal To Be Mounted On A Suitable Size Steel Plate. The Mounting Plate Shall Be Provided With Elongated Holes For Alignment Of The Pole. The Suitable Size Foundation Bolt Shall Be Supply Along With The Pole Of En 8 Grade. The Manufacturer Needs To Provide A Structural Analysis For Structural Stability Of The Pole With The Relevant Is Standards Is 1239/1161/E250 Needs To Be Clearly Mentioned. The Same Needs To Be Confirmed In Form Of Test Certificates From The Manufacturer. The Manufacturer Should Have Valid Iso 9001:2015 From Ce Certification. Please Refer The Attached Drawing No - Cameroon 3M Sa Tm Pole. , Supplying And Erecting Of Decorative Luminaire Made Of Spun Aluminium Body With An Effective Heat Sink Design To Maintain The Operating Temperatures At Led Junction And Other Components Within Permissible Limits Corresponding To The Designated Design Life. The Luminaire Shall Be Provided With Highly Efficient Pc/Pmma Lens To Provide Uniform Photometric Distribution Suitable For Typical Streetlight Application And Facilitate Minimum Glare, With Degree Of Protection As Ip66 Lamp Compartment. The Luminaire Nabl 3Rd Party Report Needs To Be Attached For Ip66 And Ies File For Lighting Distribution From Goniometer And Lm79 Report From 3Rd Party Nabl. The Diffuser Shall Be Injection Moulded Polycarbonate With Ik Rating Of /=10 (With Attached Internal Ik Report From The Manufacturer) With A Diameter Of Not Less Than 285Mm And Height Not Less Than 86Mm To Maintain The Aesthetics Of The Product As Shown In The Drawing. The Design Of The Fixture Has To Be The Same Aesthetics As Shown In The Drawing. The System Ac Wattage Of The Luminaire Shall Be 30-40W (± 10%) With Mcpcb Of Not Less Than 1.6 Mm Thickness And Cu Of 35 Microns And 2.5 Thermal Conductivity For Fixture. Colour Temperature (Cct) Of 3000K, Colour Rendering Index Cri /= 70 And Residual Flux Of 70% (L70) @ 50,000 Hours At Ta Of 25°C. The Luminaire Shall Be Suitable For Operating Within Temperature Range From - 10°C To + 40°C. The Led Used Should Be High Power Leds (Make- Osram/Bridgelux/Nichia/Cree/Lumiled) With Macadam /= 5. The Luminaire Should Be Deigned To Operate At Any Voltage From 140V To 280V, With Power Factor = 0.95 And Shall Be Provided With Optional Built In Over Voltage And Under Voltage Protection And Internal Surge Protection Of 4/4 Kv In Both Common & Differential Modes And External Surge Protection Of 10 Kv, Electrical Class I. The Driver Arrangement Should Be Such That It Can Be Easily Maintained Without Opening The Ip66 Lamp Compartment. All The Mounting Hardware Shall Be Ss316 Grade For Better Life. The Luminaire Shall Comply With Safety Requirements Of Applicable Bis Standard. Overall Outer Dimensions Of Luminaire Shall Be Ø540Mm (±3%) And 975Mmh (±3%) Height And The Shape Shall Be As Per The Sketch Attached And Non-Responsive And Accordingly Rejected. Approved Makes: Schreder/Reytek/Ligman. Important: In Case The Bidder Proposes Alternate Make, It Would Be Necessary To Submit A Fully Functional Sample Of The Luminaire Along With The Bid Failing Which The Bid Will Be Considered And Non-Responsive And Rejected. The Luminaire Should Be Having A Warranty For A Period Of 5 Years Against Any Manufacturing Defects. The Manufacturer Should Have Valid Iso 9001:2015 From Ce Certification. The Manufacturer Should Have Internal Testing Equipments Especial 2M Integrating Sphere, Ipx6, Ik10, Humidity Chamber. Similar To Model No. Rigel Pt Clear Sl 30W Led 30K The Luminaire Should Be With A Valid Bis Number. , Supplying And Erecting Of Decorative Desing Bollard Of 0.6Mtr Height Decorative Bollard Made Of Steel Pipe Which Is Fabricated Using 114M Dia X 3.0Mm Thick. The Luminaire Should Be With High Pressure Die- Cast Thermal Management For Longer Life Of The Leds And The Ip65 Optical Compartment. The Diffuser Shall Be Optical Grade Clear Pc / Pmma Pipe. The System Ac Wattage Of The Luminaire Shall Be 9W (± 10%), Colour Rendering Index Cri /= 70 And Residual Flux Of 70% (L70) @ 50,000 Hours At Ta Of 25°C. Colour Temperature (Cct) Of 3000K. The Luminaire Shall Be Suitable For Operating Within Temperature Range From - 10°C To + 40°C. The Light Source Should Be (Make- Osram/Bridgelux/Nichia/Cree/Lumiled) With Macadam /= 5. The Luminaire Should Be Deigned To Operate At Any Voltage From 140V To 280V, With Power Factor = 0.95 And Shall Be Provided With Optional Built In Over Voltage And Under Voltage Protection And Internal Surge Protection Of 4/4 Kv In Both Common & Differential Modes. The Bollard Shall Be Provided With Decorative Die Cast Aluminium Embellishment To Add Aesthetic On The Bollard As Shown In The Drawing. The Bollard Is To Be Provided With A Surface Mounting Suitable Base Plate Of 200Mm X 200Mm X And Suitable Thickness As Per Is Standards. The Decorative Base Embellisment Is Made Of Cast Aluminium Material With Minimum Dia Of The Base Is 155Mm & Height Is 120Mm. All Dimension Is Within +/- 5% Tolerance. The Base Plate Shall Be Hot Dip Galvanized. The Mounting Plate Shall Be Provided With Round Holes For Alignment Of The Bollard. Overall Outer Dimensions Of Bollard Shall Be Ø130Mm (±3%) And 600Mm (±3%) Height And The Shape Shall Be As Per The Sketch Attached Herewith. Similar To Model No. Ara Ø130Mm Bp 600H Clear 9W Led 30K. , Supplying And Erecting Of Swimming Pool Light 18W Dc Operated With Drivers And All Accessories Cct -3000K/ Rgb Ingress Protection-Ip 68 With Ss Housing, High Power Led To Be Operated On Dc, In Order To Keep The Area Safe And Shock Proof. , Supplying & Erecting Three Phase, 415V, Street Light Control Panel Up To The Max Load Of 6Kw, Tpn Mcb 40A, Powder Coated Crca 14 Swg Sheet, Outdoor Type, Having Ip54,Ik10 Protection, Suitable Rating Contactor, 24 Hrs. Astronomical Time Switch With Minimum 5 Years Battery Back Up, Auto/Manual Selector Switch, On/Off Push Buttons, Indicator Lamps, Control Wiring, Metering Device, Etc. For Automatic Operation, With Overcurrent, Short Circuit, Earth Fault Protection On Provided Iron Frame / Cement Concrete Foundation. , Supplying, Erecting & Marking Spmcb 6A To 32A, B-Series With Rated Short - Circuit Breaking Capacity (Icn) 10Ka In Provided Distribution Board As Per Specification No. Sw-Swr/Mcb , Supplying, Erecting & Marking Tpmcb 6A To 32A, With Rated Short - Circuit Breaking Capacity (Icn) 10Ka In Provided Distribution Board As Per Specification No. Sw-Swr/Mcb , Supplying, Erecting And Marking Four Pole Isolators Only Switch Version Of Miniature Circuit Breakers Of 40A In Provided Distribution Board. , Supplying & Erecting Triple Pole And Neutral Distribution Board (Tpndb), Sp/Tp Mcbs Total 4 Ways /12 Poles, With Door, 1.2Mm Thickness Surface/Flush Mounted, Ip 43 Protection On Iron/Gi Frame (Vertical Busbar Type) As Per Specification No. Sw-Swr/Mcbdb , Supplying, Erecting & Terminating Fr Xlpe Insulated, Galvanised Steel Formed Wire Armoured (Strip) Cable 1100 V, 3½ Core 25 Sq. Mm. Aluminium Conductor Complete Erected With Glands & Lugs, On Wall/ Trusses/Pole Or Laid In Provided Trench/ Pipe As Per Specification No. Cb-Lt/Al , Supplying, Erecting & Terminating Fr Xlpe Insulated, Galvanised Steel Formed Wire Armoured (Strip) Cable 1100 V, 4 Core 10 Sq. Mm. Aluminium Conductor Complete Erected With Glands & Lugs, On Wall/ Trusses/Pole Or Laid In Provided Trench/ Pipe As Per Specification No. Cb-Lt/Al , Supplying, Erecting & Terminating Fr Xlpe Insulated, Galvanised Steel Formed Wire Armoured (Strip) Cable 1100 V, 4 Core 16 Sq. Mm. Aluminium Conductor Complete Erected With Glands & Lugs, On Wall/ Trusses/Pole Or Laid In Provided Trench/ Pipe As Per Specification No. Cb-Lt/Al , Providing Pipe Type Earthing With 40Mm. Dia. G.I. Pipe Or 20 Mm Dia. G.I. Rod Complete With All Materials Testing And Recording The Results As Per Specification No. Ea-Ep , Making M- 20 Grade Reinforced Cement Concrete Foundation By Considering The Safe Soil Bearing Capacity As 10 T/Sq.M At 1.5 M Depth Including Supply Of Steel, Concrete, Excavation, Fixing Provided Nut Bolts With The Help Of Template, Duly Plastered As Per Design Complete (For 3 To 5M Octagonal / Conical Gi Pole). , Making Cement Concrete Foundation In 1:3:6 Cement Concrete, (20 To 25) Mm.Stone Metal Duly Plastered With Necessary Curing For Complete. (Pole Muffing Or Any Other Purpose). , Supplying And Laying (Including Excavation Of Suitable Width & Depth Up To 90 Cm) 50 Mm Outside Dia. Double Wall Corrugated Pipes (Dwc) Of Hdpe For Enclosing Cable Below Ground/Road Surface, To Required Depth Complete. , Supplying And Erecting Pvc Insulated Pvc Round Sheathed 1.5 Sq.Mm (30 No. X 0.25 Mm Dia.) 3 Core Flexible Multi Stranded Copper Industrial Cable For Voltage Grade Up To 1.1 Kv , Supplying, Erecting & Terminating Fr Xlpe Insulated, Galvanised Steel Formed Wire Armoured (Strip) Cable 1100 V, 4 Core 6 Sq. Mm. Aluminium Conductor Complete Erected With Glands & Lugs, On Wall/ Trusses/Pole Or Laid Inprovided Trench/ Pipe As Per Specification No. Cb-Lt/Al , Supplying And Erecting Integrated Led Flood Light Fitting Max. 155W Ip65 & Ik07 Class Having Pressure Die-Cast Aluminium Housing, Having System Lumens Output Of Min. 18600 Lumens, Min. Efficacy Of 120 Lumen/W, Cri70, Cct Upto 6500K, Thd10%, P.F. 0.90, Operating Range Of 140-270V, Inbuilt Surge Protection Of 4 Kv, Life Class Of 50,000 Hrs. At L70B50, Including Driver With U Shaped Bracket With 3 Years Warranty As Per Specification No Fg-Odf/Fls2. , Supplying, Erecting & Terminating Fr Xlpe Insulated, Galvanised Steel Formed Wire Armoured (Strip) Cable 1100 V, 4 Core 16 Sq. Mm. Aluminium Conductor Complete Erected With Glands & Lugs, On Wall/ Trusses/Pole Or Laid In Provided Trench/ Pipe As Per Specification No. Cb-Lt/Al , Supplying And Laying (Including Excavation Of Suitable Width & Depth Up To 90 Cm) 50 Mm Outside Dia. Double Wall Corrugated Pipes (Dwc) Of Hdpe For Enclosing Cable Below Ground/Road Surface, To Required Depth Complete. , Supplying And Erecting 12.5 M (Clear Height) Motorized High-Mast (Top -150Mm, Bottom- 360Mm) Hot Dipped Galvanized Material With Average Minimum Thickness 65 Micron, Made From High Tensile Structure Grade Steel As Per Bsen - 10025 S 355/E350 & 3Mm Thickness, With Base Plate 25 Mm Thick X Od 520 Mm Grade As Per Is-2062, Pole Made In Single Section & Submerge Annual Rate Contract Welded, With Lowering & Raising Motorized Unit, Wire Rope Stainless Steel 316 Grade 2 Nos., 7X19 Construction 5Mm, Sg-Dg U Clamps, Double Drum With Assembly 250 Kg, 5X2.5 Sq.Mm. Flexible Copper Cable With Lantern Carriage Assembly Suitable For Max. 12 Nos. Luminaires And Its Control Gear Box, Lightning Arrestor, Arrangement For Fixing Aviation Light, High-Mast With Serial Number, Factory Inspection Report/Test Report Of High-Mast Should Be Provided As Per Specifications On Provided Foundation J Type Stud/Bolts With Necessary Accessories Complete As Per Specification No. Ohpl/ Hm (Excluding Luminaries) , Supplying And Erecting Outdoor Stand Mounted Feeder Pillar For High-Mast Of The Same Manufacturer With 32A Tpn Mcb Incomer, 24Hr Astronomical Time Switch With Minimum 5 Years Battery Backup, Ip 54 And Ik10 Protection, 25 A Tp Contactor For Automatic Switching Of Luminaires, 2 No. 9A Contactors And Raise/Lower Push Button, And Provision For Termination Of Adequate Size Of Incoming And Outgoing Cables Complete Erected In Min. 14 Swg Crca Sheet Box With Supporting Angles, Self Lock, Gasket And Slanting Top Erected On Cement Concrete Foundation Complete. , Providng Earthing With Galvanized Iron Earth Plate Size 60 X 60 X 0.6 Cm Complete With All Materials, Testing & Recording The Results As Per Specification No. Ea-Ep , Making M- 20 Cement Concrete Foundation By Considering The Safe Soil Bearing Capacity At Site As 10 T/Sq. M At 2 M Depth Including Excavation And Fixing Provided Nut Bolts With The Help Of Template, Duly Plastered As Per Design Complete (For 12.5 M Raising Lowering High Mast).
|
