|
Flux Gel For Soldering Nc-559-Asm. Gel Flux Nc-559-Asm Is A No-Clean Gel Flux For Soldering Smd Components And Bgas. Activated Composition Based On Rosin. Provides Good Surface Wettability, Low Activation Temperature, Minimal Residues After Soldering., Choke 1Kohm@100Mhz Ferrite Bead 0805. Ferrite Bead 0805 (Choke 1Kohm@100Mhz) Is An Smd Component For Suppressing High-Frequency Interference. Impedance 1 Kohm At 100 Mhz. Size 0805. Maximum Current 200–500 Ma. Installed In Series In The Power Supply Or Signal Line For Emc Filtering., Indicator Led 0805. Indicator Led Of Standard Size 0805 Is An Smd Led For Surface Mounting. Operating Current 20 Ma. Forward Voltage 1.8–3.3 V (Depending On Color). Radiation Angle ~120°. Used To Indicate Status In Electronic Devices. Various Glow Colors Available., Flux Cleaner Flux-Off Solins 400 Ml For Removal. Flux Cleaner Flux-Off Solins, 400 Ml - Aerosol Solvent For Removing Flux Residues, Resins And Other Contaminants From Printed Circuit Boards And Electronic Components. Evaporates Quickly And Leaves No Residue. Safe For Most Plastics And Metals., Cleaning Liquid For Ultrasonic Baths Solins-Us 500Ml. A Specialized Cleaning Agent For Ultrasonic Baths. Effectively Removes Flux, Oils, Rosin And Other Contaminants From Circuit Boards And Electronic Components. Concentrated Composition, Water-Soluble, Does Not Damage Coatings., Schottky Diode Ss12 1A, 20V Sma/Do-214Ac Low-Power Rectifier Diode With Schottky Barrier. Maximum Current 1 A, Reverse Voltage 20 V. Forward Voltage Drop ~0.4 V. Sma Housing (Do-214Ac). Characterized By Short Recovery Time. Used In Protection And Rectification Circuits, Resistor 1 Mohm ±5%, 0.125 W, Size 0805 - Smd Resistor With A High Nominal Resistance. Used In Bias Circuits, Leakage Current Limiting Circuits, Rc Circuits With Large Time Constants. Power 0.125 W, Tolerance ±5%., Solder Pos-61 1Mm 100 Grams Winding. Solder Pos-61 (1 Mm, 100 G) - Tin-Lead Solder (61% Tin, 39% Lead), Diameter 1 Mm. Melting Point 183–190°C. Suitable For Mounting Larger Components And Wires. Provides A Strong And Reliable Solder Connection., Test Connector - A Special Connector For Connecting Measuring Probes, Probes Or Cables To A Board Or Device. Provides Reliable And Repeatable Electrical Contact In Measuring Circuits., Jumper (Jumper) 2.54 Mm - A Plastic Jumper With A Metal Contact For Shorting Two Adjacent Connector Pins With A Pitch Of 2.54 Mm. Used To Configure Boards (Select Operating Mode, Address). Reliable Fixation, Easy Installation And Removal., Safety Glasses Are A Means Of Personal Eye Protection When Soldering, Machining And Working With Chemicals. Provide Protection From Molten Metal Splashes, Flux, Fine Particles And Ultraviolet Radiation. Lightweight, Durable Design., Паяльная Паста Mechanic Xg30 Флюс Для Пайки Микросхем (16 Г). Solder Paste Mechanic Xg30, 16 G - Paste With Flux For Soldering Smd Chips And Components. Состав: Мелкодисперсный Порошок Олова И Флюс. Provides Uniform Application, Good Adhesion Of Components Before Soldering And High-Quality Solder Joints During Reflow., Vacuum Solder Extractor (Soldering Pump). A Vacuum Solder Extractor (De-Tin Extractor) Is A Hand-Held Tool For Removing Molten Solder. Works On The Principle Of A Vacuum Pump With Quick Release. The Tip Is Made Of Heat-Resistant Material. Effectively Cleans Mounting Holes From Tin Residues., 120 Pcs. Jumper Wires For Breadboards, Arduino Connecting Wires (10 Cm) 3 Types Of 40 Pieces Male-Male, Female-Female, Male-Female. Set Of Connecting Jumper Wires For Arduino Breadboards, 120 Pcs., Length 10 Cm. Three Types Of 40 Pcs Each: Male-Male, Female-Female, Male-Female. Provide Reliable Electrical Contact Without Soldering. Color Coding Simplifies Installation Of Circuits., The 6X6mm Tact Pushbutton Is A Miniature Pushbutton Switch For Board Mounting (Tht). Operating Voltage Up To 12 V, Current Up To 50 Ma. The Height Of The Rod Is 4–5 Mm. Type Of Action: Moment Of Pressing. Used For Resetting, Entering Commands And Controlling Electronic Devices., Co₂ Sensor Mh-Z19c Is An Infrared Ndir Carbon Dioxide Sensor With A Measurement Range Of 0–5000 Ppm. Uart/Pwm Interface. Power Supply 5 V. Built-In Automatic Calibration. Warm-Up Time ~3 Min. Used For Monitoring Air Quality In Ventilation And Climate Control Systems., Digital Ultrasonic Cleaner For Jewelry, Glasses, Ultrasonic Cleaner, 50W. Household And Professional Device For Ultrasonic Cleaning Of Jewelry, Glasses, Circuit Boards And Parts. Ultrasound Frequency ~40 Khz. Built-In Heating And Timer. Bath Capacity 600–800 Ml. Liquid Volume Up To 600 Ml., Resistor 22 Ohm ±5%, 0.125 W, Size 0805 - Low Resistance Smd Resistor. Used In Impedance Matching Circuits For Usb Lines, Led Current Limiting, And Current Measurement. Power 0.125 W, Tolerance ±5%., Microcontrollers Stm32l052k8t6. The Stm32l052k8t6 Microcontroller Is A 32-Bit Microcontroller With Ultra-Low Consumption Based On The Arm Cortex-M0+ Core. Operating Voltage 1.65–3.6 V. Flash 64 Kb, Ram 8 Kb, Eeprom 2 Kb. Lqfp-32 Housing. Frequency Up To 32 Mhz. Built-In Adc, Dac, Timers, Usart/Spi/I²c Interfaces., Pin Connector 2X20 2.54 Connection To Task Board Pls-40. Pin Connector 2×20 (40 Pins, Pitch 2.54 Mm) Pls-40 - Double-Row Pin Connector For Connecting To Task Board And Other Boards. Pitch 2.54 Mm. Allows You To Organize Reliable Inter-Board Connections. The Contacts Are Tinned, The Plastic Housing Is Standard Black., Resistor 1.5 Kohm ±5%, 0.125 W, Size 0805 - Smd Resistor. Nominal 1.5 Kohm, Tolerance ±5%, Power 0.125 W. Used In Current-Limiting Circuits, Voltage Dividers And Filters. Stable Parameters Over A Wide Temperature Range, Tantalum Capacitor 10 Μf, Size 0805 - Smd Capacitor With Solid Tantalum Electrolyte. High Capacity In A Small Body, Stable Parameters. Used For Filtering Power Supply And Decoupling Analog Circuits. It Is Important To Observe Polarity And Not Exceed Operating Voltage., Rosin For Soldering, 100 Gr. Pine Rosin For Soldering, 100 G - Natural Resin Flux. Provides Cleaning Of Soldered Surfaces From Oxides, Good Solder Spreadability And Wetting. Used For Soldering Copper And Its Alloys. Leaves Minimal Neutral Residues., 120 Pcs. Jumper Wires For Breadboards, Arduino Connecting Wires (20 Cm) 3 Types Of 40 Pieces Male-Male, Female-Female, Male-Female. Set Of Connecting Jumper Wires For Arduino Breadboards, 120 Pcs., Length 20 Cm. Three Types Of 40 Pcs Each: Male-Male, Female-Female, Male-Female. Flexible Wires With Reliable Connectors Provide A Stable Connection During Installation And Prototyping Of Electronic Circuits., Ceramic Capacitor 100 Nf 50 V, Size 0805 - Smd Capacitor. Capacitance 100 Nf (0.1 Μf), Operating Voltage 50 V. Dielectric X7r. Used To Block High-Frequency Interference In Power Supply Circuits Of Microcircuits (Bypass Capacitor). Stable Over A Wide Temperature Range., Rfid Reader Mfrc522. Rfid Reader Mfrc522 Is A Module For Contactless Reading And Writing Of Iso/Iec 14443A Standard Tags At A Frequency Of 13.56 Mhz. Spi/I²c/Uart Interface. Operating Voltage 3.3 V. Reading Range Up To 5 Cm. Includes Card And Mifare 1K Key Fob., 120 Pcs. Jumper Wires For Breadboards, Arduino Connecting Wires (30 Cm) 3 Types Of 40 Pieces Male-Male, Female-Female, Male-Female. Set Of Connecting Jumper Wires For Arduino Breadboards, 120 Pcs., Length 30 Cm. Three Types Of 40 Pcs Each: Male-Male, Female-Female, Male-Female. Extended Wires For Connecting Remote Elements On A Breadboard. Flexible, With Reliable Insulation And Durable Connectors., Exclusive Set For Learning To Solder Smd. Exclusive Training Kit For Smd Soldering - Includes A Training Board With Smd Components Of Various Sizes (Resistors, Capacitors, Microcircuits). Designed For Mastering Surface Mount Soldering Techniques. Suitable For Beginners And Intermediate Learners., Stm32f103c8t6 Microcontroller Board. Development Board Stm32f103c8t6 (Blue Pill) Is A Compact Board Based On A 32-Bit Arm Cortex-M3 Mcu. Frequency Up To 72 Mhz, Flash 64 Kb, Ram 20 Kb. Supply Voltage 3.3/5 V. Interfaces Usb, Usart, Spi, I²c, Can. St-Link Programming Connector., Goot Wick Cp-2515 Desoldering Braid, 2.5 Wide. Goot Wick Cp-2515 Desoldering Braid Is A 2.5Mm Wide Copper Braided Tape Impregnated With Flux. Effectively Absorbs Molten Solder By Capillary Method. Allows You To Carefully Remove Tin From Smd Pads And Lead Components Without The Risk Of Damaging The Board., 6F22 9V Battery For Devices. Battery 6F22 9V (Crown) Is A Primary Rectangular Chemical Battery With A Voltage Of 9 V. Type: Saline Or Alkaline. Capacity 450–600 Mah. Used In Multimeters, Testers, Alarms And Other Measuring Instruments. Standard “Button” And “Socket” Contacts., St-Link Programmer. St-Link Programmer Is A Usb Programmer And Debugger For Stm32 And Stm8 Microcontrollers. Supports Swd And Jtag Interfaces. Compatible With Development Environments Iar, Keil, Stm32cubeide. Provides Firmware, Real-Time Debugging And Monitoring Of Mk Status., Solder Pos-61, 0.5 Mm 100 Grams Wound. Pos-61 Solder (0.5 Mm, 100 G) Is A Low-Melting Tin-Lead Solder (61% Tin, 39% Lead) In The Form Of A Thin Wire 0.5 Mm Thick, Intended For Soldering Electronic Components, Printed Circuit Boards And Copper. Characterized By A Low Melting Point (183-1900C), High Spreadability And Reliable Connection, Mg996r-360 Degree Servo - Metal Gear. The Mg996r Servo Drive Is A High-Torque Servo Motor With A Metal Gearbox. Torque 9.4 Kg Cm (At 4.8 V), 11 Kg Cm (At 6 V). Rotation Angle 360°. Speed 0.17 S/60°. Power Supply 4.8–7.2 V. Pwm Signal Control. Used In Robots, Manipulators And Mechanisms., Soldering Flux Lti-120 With Brush 22 Ml. Soldering Flux Lti-120 Is A Liquid Alcohol-Rosin Flux With A Brush. Volume 22 Ml. Actively Removes Oxides From Metal Surfaces And Ensures Good Solder Spreading. Suitable For Soldering Copper, Brass, Stainless Steel. Requires Cleaning After Soldering., Usb Type B Connector Usb 2.0 Usb-B Female Connector For Surface Or Through-Board Mounting. Usb 2.0 Standard. Used In Printers, Scanners, Arduino Boards And Other Peripheral Devices. Ensures Reliable Connection Of The Usb-A – Usb-B Cable., (O061) Led Smd Ne555 Diy Kit Fanny Skill Rotating Soldering Practice Board. Soldering Training Kit - Ne555 Based Rotating Board With Smd Rgb Leds. Model O061. Designed For Practicing Component Soldering Skills. After Assembly, Performs Lighting Effects. Includes All Necessary Components And Instructions., Solder Pos-61 0.8 Mm 100 Grams Winding. Solder Pos-61 (0.8 Mm, 100 G) - Tin-Lead Solder With 61% Tin And 39% Lead, Diameter 0.8 Mm. Melting Point 183–190°C. Used For Soldering Electronic Components And Printed Circuit Boards. Provides A Reliable And High-Quality Connection., Ready-Made Printed Circuit Board Or Fr4 Fiberglass Blank With Copper Traces. Used For Mounting Electronic Components. Provides Mechanical Fastening And Electrical Connections Of Circuit Elements. Specific Parameters Depend On The Specific Board Model., Ceramic Capacitor 10 Uf 25 V, Size 0805 - Smd Capacitor For Surface Mounting. Capacitance 10 Μf, Operating Voltage 25 V. Dielectric X5r Or X7r. Used For Power Decoupling, Filtering And Buffering. Small Dimensions, High Reliability., Flux Syringe Dispenser Pusher. A Pusher-Dispenser For Syringes With Flux Is A Mechanical Device For Precise And Uniform Application Of Solder Pastes And Fluxes From Syringes. Allows You To Control The Amount Of Material Applied And Eliminates Accidental Releases. Compatible With Standard Syringes., Ncp1117lp Chip Voltage Stabilizer Ldo 3.3V 1 Asot-223. Ncp1117lp - Ldo 3.3 V Linear Voltage Regulator Chip, Maximum Current 1 A. Sot-223 Package. Input Voltage Up To 15 V. Internal Voltage Drop ~1.2 V At Full Load. Overheat And Overcurrent Protection. Used In Power Supplies For Digital Devices., 300Ma Fuse 1206. 300Ma Fuse, Size 1206 Is A Surface Mount Smd Fuse. Rated Current 300 Ma. Voltage 63 V. Fast Acting (F-Type). Protects Electronic Circuits From Overcurrent. Standard 1206 Case (3.2X1.6 Mm)., Ceramic Capacitor 470 Pf 50 V, Size 0805 - Low-Capacity Smd Capacitor. Capacitance 470 Pf, Operating Voltage 50 V. Dielectric C0g (Np0) - High Stability Of Capacitance Depending On Temperature And Voltage. Used In High-Frequency Filters, Timer And Resonant Circuits., 2X10 Pin Connector. (20 Pins, Pitch 2.54 Mm) - Double-Row Pin Connector For Board Mounting. Contact Pitch 2.54 Mm. Used For Board-To-Board Connections And Module Connections. Contact Material Is Tinned Copper., Radio Receiver Kipo-308 Ac. Radio Kipo-308 Ac Is A Portable Analog Am/Fm Radio Receiver Powered By Ac Power. Telescopic Antenna. Availability Of A Headphone Jack. Compact Case With Volume And Tuning Controls. Designed To Receive Am And Fm Radio Stations., Resistor 10 Kohm ±5%, 0.125W 0805. Resistor 10 Kohm ±5%, 0.125 W, Size 0805 - Smd Resistor For Surface Mounting. Nominal 10 Kohm, Tolerance ±5%, Power 0.125 W. Operating Voltage Up To 150 V. Temperature Range −55…+155°C. Widely Used As A Pull-Up Or Sharing Resistor., Ring Of 12 Addressable Ws2812b Leds. Rgb Ring Ws2812b, 12 Addressable Leds - Circular Led Assembly With A Diameter Of ~37 Mm. Each Led Is Controlled Independently On One Data Bus. Built-In Ws2812b Controller. Operating Voltage 5 V. Any Color (R+G+B). Compatible With Arduino, Raspberry Pi.
|
