Tender For Renovation And Upgradation Works Of Govt. Residential Qtr No. E-5 At Senior Officers Colony, Khan ... in India

Work Detail

Tender For Renovation And Upgradation Works Of Govt. Residential Qtr No. E-5 At Senior Officers Colony, Khanapara, Guwahati-22 , Earth Work In Excavation By Mechanical Means (Hydraulic Excavator)/Manual Means Over Areas (Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan) Including Getting Out And Disposal Of Excavated Earth Lead Upto 50 M And Lift Upto 1.5 M, As Directed By Engineer-Incharge. All Kinds Of Soil , Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level : 1:4:8 (1 Cement : 4 Coarse Sand (Zone-Iii) Derived From Natural Sources : 8 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources) , Brick Work With Common Burnt Clay F.P.S. (Non Modular) Bricks Of Class Designation 7.5 In Foundation And Plinth In: Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) , Cement Plaster 1:3 (1 Cement: 3 Coarse Sand) Finished With A Floating Coat Of Neat Cement. 20 Mm Cement Plaster , Structural Steel Work Riveted, Bolted Or Welded In Built Up Sections, Trusses And Framed Work, Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer All Complete. , Steel Work In Built Up Tubular (Round, Square Or Rectangular Hollow Tubes Etc.) Trusses Etc., Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer, Including Welding And Bolted With Special Shaped Washers Etc. Complete. Hot Finished Welded Type Tubes , Providing And Fixing Roofing Consist Of 0.8 Mm Thick Galvanized Steel Deck Sheet Confirming To Is 277:1992 Used As Permanent Shuttering Over Which Ms Wire Mesh 3Mm Laid At 100X100 Mm Grid Including Edge Trim Covered With Concrete. This Metal Deck Will Be Supported On Structural Steel Beam With Shear Studs. (Structural Steel Like Beam,Column, Joists Etc. & Concrete Of Different Grade As Per Design Will Be Paid Separately). , Steel Reinforcement For Reinforced Cement Concrete Work Including Straightening, Cutting,Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo-Mechanically Treated Bars Of Grade Fe-500D Or More. Kg 89.65 , Providing And Laying In Position Ready Mixed Or Site Batched Design Mix Cement Concrete For Reinforced Cement Concrete Work; Using Coarse Aggregate And Fine Aggregate Derived From Natural Sources, Portland Pozzolana / Ordinary Portland /Portland Slag Cement, Admixtures In Recommended Proportions As Per Is: 9103 To Accelerate / Retard Setting Of Concrete, To Improve Durability And Workability Without Impairing Strength; Including Pumping Of Concrete To Site Of Laying, Curing, Carriage For All Leads; But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement As Per Direction Of The Engineer-In-Charge; For The Following Grades Of Concrete. Note: Extra Cement Up To 10% Of The Minimum Specified Cement Content In Design Mix Shall Be Payable Separately. In Case The Cement Content In Design Mix Is More Than 110% Of The Specified Minimum Cement Content, The Contractor Shall Have Discretion To Either Re-Design The Mix Or Bear The Cost Of Extra Cement. All Works Above Plinth Level Upto Floor V Level Concrete Of M25 Grade With Minimum Cement Content Of 330 Kg /Cum , Providing Wood Work In Frames Of Doors, Windows, Clerestory Windows And Other Frames, Wrought Framed And Fixed In Position With Hold Fast Lugs Or With Dash Fasteners Of Required Dia & Length (Hold Fast Lugs Or Dash Fastener Shall Be Paid For Separately). Second Class Teak Wood , Providing And Fixing Bright Finished Brass Single Acting Spring Hinges With Necessary Brass Screws Etc. Complete : 150 Mm , Providing And Fixing Factory Made Laminated Veneer Lumber Glazed Shutter Conforming To Is: 14616 And Tads 15:2001 (Part B), Using 4 Mm Thick Float Glass Panes For Doors, Windows And Clerestory Windows, Fixing With Butt Hinges Of Required Size With Necessary Screws, All As Per Directions Of Engineer-In-Charge (Note:- Butt Hinges And Necessary Screws Shall Be Paid Separately) 30 Mm Thick Shutters , Extra For Providing Frosted Glass Panes 4 Mm Thick Instead Of Ordinary Float Glass Panes 4 Mm Thick In Doors, Windows And Clerestory Window Shutters. (Area Of Opening For Glass Panes Excluding Portion Inside Rebate Shall Be Measured). , Polishing In High Gloss/Matt Finish Melamine Clear Polish On Wood Work In Required Color/Wooden Shade Texture With Following Process In The Sequence As Detailed Below: 1. The Surface To Be Polished Is Rubbed With Sand Paper 80/120 No.And Then With Sand Paper Of 160/180 Nos. 2. Applying Two Coats Of Sealer With Spray Gun And Allowing Sufficient Drying Time For 1St Coat And 2Nd Coat Is Allowed To Dry For 8 To 12Hrs. 3. On Drying Of Sealer Coat, Wet Rubbing With Emery Cloth Of Finer Grading With Ample Water To Remove Excess Sealer Layer And Make The Surface Further Smooth After This Wet Rubbing, Then Surface Is Applied With Special Grade Melamine Fillers To Fill All The Small And Big Holes/Grooves Etc. Filler Coat To Be Allowed To Dry For 4 To 6 Hrs On Which Again A Light Wet Rubbing Is Done This Surface Is Further Allowed To Dry For 12 Hrs. 4. On This, 1St Coat Of Melamine Polish Is Applied With Spray Gun Using Melamine Clear Polish And Melamine Thinner In Required Proportion. This 1St Coat Is Allowed To Dry For 24 Hrs Then This Dry Surface Is Again Fine Wet Rubbed Smooth, Which Is Further Allowed To Dry For 12 Hrs. The Final Melamine Polish Is Applied With Compressor Pressure Spray Gun Using Melamine Clear Polish And Melamine Thinner Mixed In Required Proportion Complete As Per Direction Of Engineer-In-Charge. (Final Coat To Be Done In 1 Or 2 Layers Without Gap Of Time.) , Providing And Fixing Brass 100Mm Mortice Latch And Lock With 6 Nlevers Without Pair Of Handles (Best Make Of Approved Quality) For Aluminium Doors Including Necessary Cutting And Making Good Etc.Complete. , Providing And Fixing Factory Made Upvc White Colour Casement/ Casement Cum Fixed Glazed Door Comprising Of Upvc Multi-Chambered Frame,Sash And Mullion (Where Ever Required) Extruded Profiles Duly Reinforced With 1.60 ± 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), Upvc Extruded Glazing Beads Of Appropriate Dimension, Epdm Gasket, Zinc Alloy (White Powder Coated) 3D Hinges And One Handle On Each Side Of Panels Along With Zinc Plated Mild Steel Multi Point Locking Having Transmission Gear, Cylinder With Keeps And One Side Key, G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall And Necessary Stainless Steel Screws, Etc. Profile Of Frame & Sash Shall Be Mitred Cut And Fusion Welded At All Corners, Mullion (If Required) Shall Be Also Fusion Welded Including Drilling Of Holes For Fixing Hardwares And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealent Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single / Double Glass Panes And Silicon Sealent Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame, Sash And Mullion Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Casement Door With 3D Hinges Made Of (Big Series) Frame 67 X 64 Mm & Sash 67 X 110 Mm Both Having Wall Thickness Of 2.3 ± 0.2 Mm And Single Glazing Bead / Double Glazing Bead Of Appropriate Dimension. (Area Of Door Upto 2.00 Sqm). , Providing And Fixing Factory Made Upvc White Colour Fixed Glazed Windows/Ventilators Comprising Of Upvc Multi-Chambered Frame And Mullion (Where Ever Required) Extruded Profiles Duly Reinforced With 1.60 ± 0.2Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), , Upvc Extruded Glazing Beads Of Appropriate Dimension, Epdm Gasket, G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall, Plastic Packers, Plastic Caps And Necessary Stainless Steel Screws Etc. Profile Of Frame Shall Be Mitred Cut And Fusion Welded At All Corners, Mullion (If Required) Shall Be Also Fusion Welded Including Drilling Of Holes For Fixing Hardwares And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealant Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge.(Single / Double Glass Panes And Silicon Sealant Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame, Sash And Mullion Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Fixed Window / Ventilator Made Of (Small Series) Frame 47 X50 Mm & Mullion 47 X 68 Mm Both Having Wall Thickness Of 1.9 ± 0.2 Mm And Single Glazing Bead Of Appropriate Dimension. (Area Upto 0.75 Sqm.) , Providing And Fixing Factory Made Upvc White Colour Sliding Glazed Window Upto 1.50 M In Height Dimension Comprising Of Upvc Multi-Chambered Frame With In-Built Roller Track And Sash Extruded Profiles Duly Reinforced With 1.60 ± 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), Appropriate Dimension Of Upvc Extruded Glazing Beads And Upvc Extruded Interlocks, Epdm Gasket, Wool Pile, Zinc Alloy (White Powder Coated) Touch Locks With Hook, Zinc Alloy Body With Single Nylon Rollers (Weight Bearing Capacity To Be 40 Kg), G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall And Necessary Stainless Steel Screws Etc. Profile Of Frame & Sash Shall Be Mitred Cut And Fusion Welded At All Corners, Including Drilling Of Holes For Fixing Hardwares And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealent Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single /Double Glass Panes,Wire Mesh And Silicon Sealent Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame And Sash Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Two Track Two Panels Sliding Window Made Of (Small Series)Frame 52 X 44 Mm &Sash 32 X 60 Mm Both Having Wall Thickness Of 1.9 ± 0.2 Mm And Single Glazing Bead Of Appropriate Dimension. (Area Of Window Upto 1.75 Sqm) , Two Track Two Panels Sliding Window Made Of (Big Series) Frame 67 X 50 Mm & Sash 46 X 62 Mm Both Having Wall Thickness Of 2.3 ± 0.2 Mm And Single Glazing Bead / Double Glazing Bead Of Appropriate Dimension . (Area Of Window Above 1.75 Sqm Upto 2.50 Sqm). , Three Track Three Panels Sliding Window With Fly Proof S.S Wire Mesh (Two Nos. Glazed & One No. Wire Mesh Panels) Made Of (Big Series) Frame 116 X 45 Mm & Sash 46 X 62 Mm Both Having Wall Thickness Of 2.3 ± 0.2 Mm And Single Glazing Bead / Double Glazing Bead Of Appropriate Dimension. (Area Of Window Above 1.75 Sqm). , Providing And Fixing Glazing In Aluminium Door, Window, Ventilator Shutters And Partitions Etc. With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Architectural Drawings And The Directions Of Engineer-In-Charge . (Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item): With Float Glass Panes Of 5 Mm Thickness (Weight Not Less Than 12.50 Kg/Sqm) , Filling The Gap In Between Aluminium Frame & Adjacent Rcc/ Brick/Stone Work By Providing Weather Silicon Sealant Over Backer Rod Of Approved Quality As Per Architectural Drawings And Direction Of Engineer-In-Charge Complete. Upto 5Mm Depth And 5 Mm Width , Providing And Fixing Fly Proof Stainless Steel Grade 304 Wire Gauge, To Windows And Clerestory Windows Using Wire Gauge With Average Width Of Aperture 1.4 Mm In Both Directions With Wire Of Dia. 0.50 Mm All Complete. With 2Nd Class Teak Wood Beading 62X19 Mm Sqm 1404.25 With 12 Mm Mild Steel U Beading , Providing And Fixing 19Mm Thick Both Side Balancing Lamination Factory Pressed Bwp Grade Marine Ply As Per Is 710 Of Approved Brand Boxes,Shelves,Racks,Almirah,Cupboard And Drawer Etc. Including Necessary Nails,Screws Etc. Complete As Per Direction Of Engineer-Incharge. , Providing And Fixing Cupboard Shutter With 19Mm Thick One Side Decorative And Other Side Balancing Lamination Factory Pressed Bwp Grade Marine Ply As Per Is 710 Of Approved Brand Including 2Mm Thick Pvc Edge Banding Tape With Hot Glue By Edge Bending Machine Etc. With Auto Closing Spring Loaded Hinges (Hydraulic Type) Etc. Complete As Per Direction Of Engineer-In-Charge.(Payment Of Providing And Fixing Auto Closing Hinges Shall Be Paid Separately) , Providing & Fixing Glass Panes With Putty And Glazing Clips In Steel Doors,Windows, Clerestory Windows, All Complete With : 4.0 Mm Thick Glass Panes , Providing And Fixing Stainless Steel Soft Closing Spring Hinges At 0 Degree Hinges (Hydraulic Type) Of Approved Make/Brand To Cupboard Shutters With Full Threaded Steel Screws Including Making Necessary Recess In Board And Finished Etc. Complete As Per Direction Of Engineer-In-Charge. , Providing And Fixing Stainless Steel Soft Closing Heavy Type Telescopic Drawer Channels Of Approved Make 500 Mm Long With Screws Etc.Complete As Per Directions Of Engineer- In-Charge. , Providing And Fixing 2Mm Thick 16 To 19Mm Wide Pvc Edge Binding Tape Of Approved Quality For Cupboard/Wardrobe Shutters Including Necessary Synthetic Resin Hot Pressed To Edges On Binding Machine Etc. Complete As Per Directions Of Engineer- In-Charge. , Cement Concrete Flooring 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) Finished With A Floating Coat Of Neat Cement, Including Cement Slurry, But Excluding The Cost Of Nosing Of Steps Etc. Complete. 40 Mm Thick With 20 Mm Nominal Size Stone Aggregate , Providing And Laying Vitrified Tiles In Floor In Different Sizes (Thickness To Be Specified By The Manufacturer) With Water Absorption Less Than 0.08% And Conforming To Is:15622, Of Approved Brand & Manufacturer, In All Colours And Shade, Laid On 20 Mm Thick Cement Mortar 1:4 (1 Cement:4 Coarse Sand) Jointing With Grey Cement Slurry @3.3 Kg/Sqm Including Grouting The Joints With White Cement And Matching Pigments Etc. The Tiles Must Be Cut With The Zero Chipping Diamond Cutter Only . Laying Of Tiles Will Be Done With The Notch Trowel, Plier, Wedge, Clips Of Required Thickness, Leveling System And Rubber Mallet For Placing The Tiles Gently And Easily. Glazed Vitrified Floor Tiles Polished Finish Of Size Size Of Tile 600 X 1200 Mm , Providing And Laying Vitrified Tiles In Different Sizes (Thickness To Be Specified By Manufacturer), With Water Absorption Less Than 0.08 % And Conforming To I.S. 15622, Of Approved Make, In All Colours & Shade, In Skirting, Riser Of Steps, Over 12 Mm Thick Bed Of Cement Mortar 1:3 (1 Cement: 3 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/Sqm Including Grouting The Joint With White Cement & Matching Pigments Etc. Complete. Size Of Tile 600X600 Mm , Providing And Laying Polished Granite Stone Flooring In Required Design And Patterns, In Linear As Well As Curvilinear Portions Of The Building All Complete As Per The Architectural Drawings With 18 Mm Thick Stone Slab Over 20 Mm (Average) Thick Base Of Cement Mortar 1:4 (1 Cement : 4Coarse Sand) Laid And Jointed With Cement Slurry And Pointing With White Cement Slurry Admixed With Pigment Of Matching Shade Including Rubbing, Curing And Polishing Etc. All Complete As Specified And As Directed By The Engineer-In-Charge. Polished Granite Stone Slab Colour Of Black, Cherry/Ruby Red Or Equivalent , Providing And Laying Flamed Finish Granite Stone Flooring In Required Design And Patterns, In Linear As Well As Curvilinear Portions Of The Building All Complete As Per The Architectural Drawings With 18 Mm Thick Stone Slab Over 20 Mm (Average) Thick Base Of Cement Mortar 1:4 (1 Cement : 4Coarse Sand) Laid And Jointed With Cement Slurry And Pointing With White Cement Slurry Admixed With Pigment Of Matching Shade Including Rubbing, Curing And Polishing Etc. All Complete As Specified And As Directed By The Engineer-In-Charge : Flamed Finish Granite Stone Slab Jet Black, Cherry Red, Elite Brown, Cat Eye Or Equivalent. , Providing And Fixing 18 Mm Thick Gang Saw Cut, Mirror Polished, Premoulded And Prepolished, Machine Cut For Kitchen Platforms, Vanity Counters, Window Sills, Facias And Similar Locations Of Required Size, Approved Shade, Colour And Texture Laid Over 20 Mm Thick Base Cement Mortar 1:4 (1 Cement : 4 Coarse Sand), Joints Treated With White Cement, Mixed With Matching Pigment, Epoxy Touch Ups, Including Rubbing, Curing, Moulding And Polishing Of Edges To Give High Gloss Finish Etc. Complete At All Levels. Granite Stone Slab Of Colour Black, Cherry/Ruby Red Area Of Slab Over 0.50 Sqm , Extra For Providing Opening Of Required Size & Shape For Wash Basin/Kitchen Sink In Kitchen Platform, Vanity Counter And Similar Location In Marble/ Granite/ Stone Work, Including Necessary Holes For Pillar Taps Etc. Including Moulding, Rubbing And Polishing Of Cut Edges Etc. Complete. , Providing And Fixing False Ceiling At All Height Including Providing And Fixing Of Frame Work Made Of Special Sections, Power Pressed From M.S. Sheets And Galvanized With Zinc Coating Of 120 Gms/Sqm (Both Side Inclusive) As Per Is : 277 And Consisting Of Angle Cleats Of Size 25 Mm Wide X 1.6 Mm Thick With Flanges Of 27 Mm And 37Mm, At 1200 Mm Centre To Centre, One Flange Fixed To The Ceiling With Dash Fastener 12.5 Mm Dia X 50Mm Long With 6Mm Dia Bolts, Other Flange Of Cleat Fixed To The Angle Hangers Of 25X10x0.50 Mm Of Required Length With Nuts & Bolts Of Required Size And Other End Of Angle Hanger Fixed With Intermediate G.I. Channels 45X15x0.9 Mm Running At The Spacing Of 1200 Mm Centre To Centre, To Which The Ceiling Section 0.5 Mm Thick Bottom Wedge Of 80 Mm With Tapered Flanges Of 26 Mm Each Having Lips Of 10.5 Mm, At 450 Mm Centre To Centre,Shall Be Fixed In A Direction Perpendicular To G.I. Intermediate Channel With Connecting Clips Made Out Of 2.64 Mm Dia X 230 Mm Long G.I. Wire At Every Junction, Including Fixing Perimeter Channels 0.5 Mm Thick 27 Mm High Having Flanges Of 20 Mm And 30 Mm Long, The Perimeter Of Ceiling Fixed To Wall/Partition With The Help Of Rawl Plugs At 450 Mm Centre, With 25Mm Long Dry Wall Screws @ 230 Mm Interval, Including Fixing Of Gypsum Board To Ceiling Section And Perimeter Channel With The Help Of Dry Wall Screws Of Size 3.5 X 25Mm At 230 Mm C/C, Including Jointing And Finishing To A Flush Finish Of Tapered And Square Edges Of The Board With Recommended Jointing Compound , Jointing Tapes , Finishing With Jointing Compound In 3 Layers Covering Upto 150 Mm On Both Sides Of Joint And Two Coats Of Primer Suitable For Board, All As Per Manufacturers Specification And Also Including The Cost Of Making Openings For Light Fittings, Grills,Diffusers, Cutouts Made With Frame Of Perimeter Channels Suitably Fixed, All Complete As Per Drawings, Specification And Direction Of The Engineer In Charge But Excluding The Cost Of Painting With : 12.5 Mm Thick Tapered Edge Glass Reinforced Gypsum (Grg) Board Conforming To Is: 2095- (Part 3):1996 (Boards With Bis Certification Marks) , Providing And Fixing At All Height False Ceiling Of 4Mm Thick Phenol Bonded Bamboo Mat Board (595X595mm) Conforming To Is:13958-1994 Including Providing And Fixing Of Frame Work Made Of Gi Angle 25X25x0.4 Mm Thick All Around Suitably Fixed To Wall With The Help Of Dash Fastener And Hanger Frame (600X600 C/C) Made Gi Slotted Tee Having Powder Coating On Bottom Side (30X25x0.3 Mm Thick For Main Member & 25X25x0.3 Mm For Cross Member) Connected To Ceiling With 2.64Mm Gi Wire And Anchor Fastener At Every Junction And Also Including Cost Of Making Openings For Light Fittings, Grills, Diffusers,Cut Outs Made With Frame Of Perimeter Channels Suitably Fixed All Complete As Per Direction Of Engineer-In-Charge. , Providing And Fixing 15 Cm Wide, 45 Cm Overall Semi-Circular Plain G.S. Sheet Gutter With Iron Brackets 40X3mm Size, Bolts, Nuts And Washers Etc., Including Making Necessary Connections With Rain Water Pipes Complete. 0.63 Mm Thick With Zinc Coating Not Less Than 275 Gm/M² , Providing Corrugated G.S. Sheet Roofing Including Vertical / Curved Surface Fixed With Polymer Coated J Or L Hooks, Bolts And Nuts 8Mm Diameter With Bitumen And G.I. Limpet Washers Or With G.I. Limpet Washers Filled With White Lead, Including A Coat Of Approved Steel Primer And Two Coats Of Approved Paint On Overlapping Of Sheets Complete (Up To Any Pitch In Horizontal/ Vertical Or Curved Surfaces),Excluding The Cost Of Purlins, Rafters And Trusses And Including Cutting To Size And Shape Wherever Required. 0.80 Mm Thick With Zinc Coating Not Less Than 275 Gm/M² , Finishing Walls With 100% Premium Acrylic Emulsion Paint Having Voc Less Than 50 Gm/Litre And Uv Resistance As Per Is 15489:2004,Alkali & Fungal Resistance, Dirt Resistance Exterior Paint Of Required Shade (Company Depot Tinted) With Silicon Additives. New Work (Two Or More Coats Applied @ 1.43 Litre/ 10Sqm. Over And Including Priming Coat Of Exterior Primer Applied @ 0.90 Litre/10 Sqm. , Providing And Fixing Approved Brand And Manufacture Ss Handle Of Size 600 Mm Fixed With Ss Screws Etc, Complete In All Respects As Per Manufacturers Specifications & As Directed By Engineer-In-Charge. , Providing And Fixing Approved Brand And Manufacture Ss 304 Grade Top & Bottom Patch Fixed With Ss Screws Etc. Complete In All Respects As Per Manufacturers Specifications & As Directed By Engineer-In-Charge. , Providing And Fixing Approved Brand And Manufacture Ss 304 Grade 900Mm Pull Handle With 32Mm Dia Fixed With Ss Screws Etc. Complete In All Respects As Per Manufacturers Specifications & As Directed By Engineer-In-Charge. , Providing And Fixing Approved Brand And Manufacture Ss 304 Grade Glass To Glass Lock Round Type With Ss Screws Etc. Complete In All Respects As Per Manufacturers Specifications & As Directed By Engineer-In-Charge. , Providing And Fixing Approved Brand And Manufacture Ss 304 Grade Floor Spring (Weight Approx 100-120Kgs) Fixed With Ss Screws Etc. Complete In All Respects As Per Manufacturers Specifications & As Directed By Engineer-In-Charge. , Supplying, Fitting And Fixing Full Height Wooden Partition Made Of Secondary Seasoned Hard Wood As Approved, Out Of 60Mm X 50Mm Section Both Horizontal And Vertical @ 600 C/C Including Covering The Above Frame (Primary Surface) With 12Mm Bwr Ply Wood On Both Side With 1.0 Mm Thk Laminate Finish And Necessary Edge Finish As Approved All Complete As Per Architectural Drawings And The Directions Of Engineer-In-Charge. , Providing And Fixing 40Mm Thick Cladding Comprising Of Wooden Framework Using 25Mx50mm Sections At A Maximum Spacing Of 600Mm In Any One Direction (Including Adding Members As Required) Covered With12mm Thick Bwp Ply Layered With 4Mm Thk. Veneer (Basic Rate Rs.60/-Sqftjon One Side Pasted And Pressed With Adhesive To Give A Uniform And Smooth Finish, Including 4Mm Thk. S.S. Strip Framework On All Sides Of Veneer Panels With Wooden Member Surround, Top Moldings/Margins, Etc. To Finish The Thickness, As Shown Complete In Drawing. All Members/Ply Etc. Shall Be Treated With Anti-Termite Solution As Per Norms. No Extra Shall Be Pald For Maling Of Openings, Door / Window Frames And For Making Provisions For Electric Condults. , Providing And Fixdng 18Mm Thick Granite Stone Work For Wall Lining Upto 10 M Height In Cement Mortar 1:3 (1Cement: 3 Coarse Sand) Including Pointing With White Cement Mortor With An Admixture Of Pigment To Match The Granite Shade Complete As Per Direction Of Engineer-In-Charge. , Providing And Laying Laminate Wooden Flooring (Grade Ac4, 8 Mm Thick Ambience Premium-Ac4), Having A Good Backing Layer Made Up Of Plastic Laminate Or Melamine As Specified By The Manufacturer And Approved By Engineer-Incharge. , Providing And Fixing Bamboo Composite Roof All Complete As Per Direction Of Engineer-In-Charge. , 1650 Mm Height Bamboo Boundary Wall As Per Direction Of Engineer-In Charge. , Providing Fitting And Fixing Of Branded Modular Lit And Wall Cabinet For Iitchen Along With Hardware Fittings At Senior Officers Colony As Per Direction Of Engineer-In-Charge. , Wiring For Light Point/ Fan Point/ Exhaust Fan Point/ Call Bell Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface/ Recessed Medium Class Pvc Conduit With Modular Switch Modular Plate Suitable Gi Box And Earthing The Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc.As Required. Group C , Wiring For Circuit/ Submain Wiring Alongwith Earth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface/ Recessed Medium Class Pvc Conduit As Required. 2 X 1.5 Sq.Mm. + 1 X 1.5 Sq.Mm. Earth Wire. , 2 X 2.5 Sq.Mm. + 1 X 2.5 Sq.Mm. Earth Wire. , 2 X 4 Sq. Mm + 1 X 4 Sq. Mm Earth Wire , 2 X 6 Sq. Mm + 1 X 6 Sq. Mm Earth Wire , 4 X 16 Sq. Mm + 2 X 6 Sq. Mm Earth Wire , Supplying And Fixing Following Modular Switch/ Socket On The Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Required. 5/6 Amps Switch , 15/16 Annual Periodical Maintenance Switch , 3 Pin 5/6 Annual Periodical Maintenance Socket Outlet , 6 Pin 15/16 Annual Periodical Maintenance Socket Outlet , Telephone Socket Outlet , Tv Antenna Socket Outlet , Bell Push , Supplying And Fixing Two Module Stepped Type Electronic Fan Regulator On The Existing Modular Plate Switch Box Including Connections But Excluding Modular Plate Etc. As Required. , Supplying And Fixing Following Size/ Modules, Gi Box Along With Modular Base & Cover Plate For Modular Switches In Recess Etc As Required. 3 Module (100Mmx75mm) , 4 Module (125Mmx75mm) , 6 Module (200Mmx75mm) , 8 Module (125Mmx125mm) , 12 Module (200Mm X 150Mm) , Supplying And Fixing Following Modular Base & Cover Plate On Existing Modular Metal Boxes Etc. As Required. 3 Module , 4 Module , 6 Module , 8 Module , 12 Module , Supplying And Fixing Call Bell/ Buzzer Suitable For Single Phase, 230 Volts, Complete As Required. , Installation, Testing And Commissioning Of Ceiling Fan, Including Wiring The Down Rods Of Standard Length (Upto 30 Cm) With 1.5 Sq. Mm Frls Pvc Insulated, Copper Conductor, Single Core Cable Etc. As Required. , Supplying And Fixing 5 Amps To 32 Amps Rating, 240/415 Volts, C Curve, Miniature Circuit Breaker Suitable For Inductive Load Of Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required. Single Pole , Supplying And Fixing Following Rating, Four Pole, 415 Volts, Isolator In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required. 63 Amps , Supply, Installation, Testing And Commissioning Of 1200 Mm Sweep, Bee 5 Star Rated, Ceiling Fan With Brush Less Direct Current (Bldc) Motor, Class Of Insulation: B, 3 Nos. Blades, 30 Cm Long Down Rod, 2 Nos. Canopies, Shackle Kit, Safety Rope, Copper Winding, Power Factor Not Less Than 0.9, Service Value (Cm/M/W) Minimum 6.00, Air Delivery Minimum 210 Cum/Min , 350 Rpm (Tolerance As Per Is : 374-2019), Thd Less Than 10%, Remote Or Electronic Regulator Unit For Speed Control And All Remaining Accessories Including Safety Pin, Nut Bolts, Washers, Temperature Rise=75 Degree C (Max.), Insulation Resistance More Than 2 Mega Ohm, Suitable For 230 V, 50 Hz, Single Phase Ac Supply, Earthing Etc. Complete As Required. , Supplying Including Fitting Fixing Of Following A.C. 2 Model Starter In The Existing 2 Model Modular Board Necessary Connection As Approved By The Deptt.)As 6 Required Complete And As Directed By The Department.25 Amps 2 Module Starter , Supplying Installation Testing And Commissioning Of Exhust Fan 225 Mm Air Flow As Required 1.5 Sq Mm Copper Multstrand Wire Connection An As Specified 3 And Directed By The Deptt. Orient/Usha/Cromton Make , Supplying And Fixing Of Recessed Jaquar Or Equivalent Philips/ Wipro Led Spot Light Fittings Complete With Shade, Back Plate Including Connection Cable, As 5 Approved By The Deptt.S Etc. As Required. 7W Led Cob , Supplying, Installation, Testing And Commission Of The Following Indoor Decorative Recess Mounted Led Down Lighter Luminaries Of Model No- Dn296b Led15s-6500Psu Wh Hsn Code 9405 Complete With All Accessories Such As Ballast, Starter Etc. In The False Ceiling Type Armstrong /Gypsum Or Similar Celling 6 Mounting With Necessary Support With 1.5 Sq.Mm. P.V.C. Insulated S.C.Copper Conductor As Required And As Directed By The Department (Philips/Jaquar / Lt/Wipro Make) , Supplying, Installation, Testing And Commission Of The Following Indoor Decorative Recess Mounted Liner Led Strip Light Premium 50W With Derver Complete With All Accessories Such As Ballast, Starter Etc. In The False Ceiling Type Armstrong/Gypsum Or Similar Celling Mounting With Necessary Support With 1.5 Sq.Mm. P.V.C. Insulated S.C.Copper Conductor As Required And As Directed By The Department (Philips/Jaquar/Lt/Wipro Make). 50 W Led Strip Light

Contact Information