|
Bids Are Invited For Erection Of 01 No 132 Kv Garda Solar Private Limited Bay (2*Main+1*Trasfer Bus Scheme) On Deposit Head At 220 Kv S/S Charkhari Under Etd Hamirpur; 1 Erection of Main and auxiliary structure consisting of columns, beams, peaks, masts etc. and auxiliary structure required for installation of isolators, C.Ts. P.Ts. L.As. and all other equipments. All material to be erected shall be supplied by UPPTCL free of cost but all men, material and T&P required for satisfactorily completion of work shall be arranged by the contractor at his own cost. a 132KV side (Main & Auxilary structure) MT 8.09 b Shifting of all material equipment from store to site to work site like breaker,CT,Isolatoretc. by hydra/conventional means Job 1 2 Erection of following equipments 01 no.132kV Bay of M/s Garda Solar Bay at 220kV Substation Charkhari i 145 KV Circuit Breaker No. 1 ii 145 KV Potential Transformer No. 3 iii 145 KV Current Transformer No. 3 iv 145 KV Post Insulator No. 32 v 145 KV Line Isolator (Motorised) without polycone No. 1 vi 145 KV Bus Isolator (Motorised) without polycone No. 1 vii 145 KV Tendem Isolator (Motorised) without polycone No. 2 viii 120 KV L.A. No. 3 ix CT Junction Box No. 1 x PT Junction Box No. 1 xi 132 KV Simplex feeder C&R Panel (SAS Based) No. 1 xii Meter Cubical with 02 No. ABT Meter No. 1 3 Jumpering ,interconnection of equipment with specified conducter of various 132kV equipments with main and transfer bus bar.The work includes cutting and bending of conducter in proper shape clamping with the help of the clamps and shifting of material from store room to erection site to work site and all other associated to complete the work at 132kV line bay No. 52 4 Cutting,strengthening,bending,laying 600mm.below in side ground and above ground of following size of MS Flat for earthing of main and auxiliary structure, equipment structure and its material etc. Including welding with main earth mat and with object to be earthed /excavation of trenches its back filling painting and all other associated work. Excluding cost of MS Flat i 75X10mm RMT 200 ii 50X6mm RMT 250 iii 25X6mm RMT 100 6 Preparation of interconnection diagram of various connection between CB, CT, PT & CRP etc. Job 1 7 Laying of following sizes of control cable in the cable trench from control relay panel to various equipments / marshalling boxes and JB etc. In switchyard as per cable schedule. i 2C x 2.5 Sq mm. unarmoured. Km 1.5 ii 4C x 2.5 Sq mm. unarmoured. Km 4 iii 6C x 2.5 Sq mm. unarmoured. Km 3.5 iv 10x2.5 Sq mm. unarmoured. Km 1 8 Termination of various sizes of above laid control cable as per cable schedule including making necessary holes in glands plates or box where ever required supply and fixing of cable glands of appropriate size, supply & providing ferrules & Nos for each core of cable and its termination with crimping type lugs of dowell/tension make and all other associated work to complete the job satisfactory. Nos 1 9 Making earthing of LA including work of digging of soil upto 1 Mtr depth or as per reqirements removel of stone and brick work if required. Making 06 no holes in soil across structure of 132kv side LA. Fabrication minimum 3 mtr long electrodes from 40mm dia MS round having one side conical shape. Placing of electordes and laying of 75x10 mm MS flat as per drawing or site condition including work of shifting of material cutting, bending, drilling and welding at joints of 75x10mm MS flat and 40mm round etc. Connecting the newly made delta by X - Y MS round of existing earthmate as per drawing with the help of 75x10 mm MS flate. Back filling of soil etc. Making connection of LA/surge counter by riser from 75*10 ms Flate as per standard approved drawing . Job 1 10 Cutting, Fabrication and fixing of angle iron by welding including cost of electrodes, labour, T&P. Details of every job includes- Nos 20 (a) Taking out scrap angle heap of scrap, cutting the cleats of 50x50x6mm angle iron & shifting back the scrap (b) Fixing of cleats of angle iron by welding including cost of electrodes, labor, T&P. 11.1 Fabrication of 3M long Electrode with 40MM dia M.S. rod having 150mm long conical shape and then its piercing vertically in side the ground with top 600mm.below ground level and its welding with earthmat, excluding the cost of M.S. bar. Nos 10 11.2 Boring with 150 mm Dia casing pipe to a depth of 27.00 meter long from ground level with skilled and unskilled labour including all T&P, boring apparatus and supervision charges etc. required for proper completion of work. By Inserting 40x6 mm GI Flat in 50 mm Dia B-class (Jindal) ISI mark 6.0 meter long 3 pipe placed horizontally on ground and bolting the G.I flat with 150 mm long 75x6 mm copper plate conical piece on and then bolting the G.I flat with G.I pipe in such a way that flat remains in contact with the pipe, Lowering of 6.0 meter long with G.I pipe with conical copper plate connected and at bottom along with G.I flat inside the pipe in boring of 150 mm G.I pipe pieces by G.I sockets along with 40x6 mm G.I flat from the upper end of pipe by making a cut of 45 mm wide up to a depth of 50 mm in upper portion of G.I pipe and providing 01 no. cap type G.I socket on upper treaded portion of pipe for water pouring in the pipe at regular intervals filling the space. Mtr. 30 11.3 Excavation of pit of size 2.00x2.00x4.5 driven of M.S electrodes of 40/36/32 mm dia 3.0 mtr long in the earth at four corners of the pit at equal distance of 2.0 mtr long, keeping the top of electrode 50 cm above the pit ground level, welding of 40 mm M.S round pieces of 03 mtr long on all four sides of electrodes and 15 cm below of top of electrodes by 08 nos U type clamp of 50x6 mm G.I flat on opposite side of square welding of 40x6 mm G.I flat on opposite M.S electrode driven in ground and connecting the 40x6 mm G.I flat. MS Flat will be provided by department free of cost as per actual consumption. Job 1 11.4 Interconnecting work of connecting bore earth point with near by Main structure of 132 KV Gaintry of 132 KV GARDA SOLAR PRIVATE LIMITED bay equipments with MS Flat of size 50x6 mm. This work includes laying, cutting, bending, welding and painting of MS Flat with one coat of Red oxide primer and two coats of Green colour of standard make like Nerolac, Berger, Asian etc. Mtr. 50 12.1 Supply and fixing of 120 watt LED Lamps Cropmton Greaves, Bajaj/Havells make fitting including lamp, Ballast Igniter etc. For fixing of structure including cost of all material labour and T&P for completion of work. Job 10 12.2 Supply and fixing of Junction Box on lighting polls of size 200x200x150mm of MS seat SWG duly painted with synthetic enamel paint box should be fixing and Backlite terminal strip of 4 Nos terminal both should be fixing on Sunmica seat and half round MS clamp with GI pipe for fixing the Junction box on the structure Job 10 12.3 Supply and fixing of 16 Amp. MCB make Crompton Greaves, Bajaj/Havells make fitting on structure including cost of all material, labour and T&P for completion of work. JOb 10 12.4 Laying of 2x2.5/4x2.5mm sq.mm PVC cable 50 cm below the ground level in PVC conduit pipe after excavation and back filling including all labour PVC pipe etc. Mtr. 250 13 Laying the 01 Nos. 4x2.5 Sq. mm control cable for CT & PT with provision of vermin proofing in galv. MS pipe in individual 'B' Class pipe of Jindal/TATA/JSW/SAIL, 1" dia with jointing with Tee, Elbow, bend, Socket etc. Including cost of material of pipe and other accessories. Separate pipe will be made in trench for each control cable. Control cable will be provided by the department as per actual consumption. RMT 300 14.1 Digging of trench of 300 mm depth from surface level and suitable width for laying of 40 mm Gl pipe nearby the approch road of through-out the switch yard including cutting of concreate road (if necessary for road crossing) and hack filling of trech with re concreating of cutting road after laying of pipe line. Mtr. 100 14.2 Provinding and laying of 40 mm din B-class, ISI marked Gl pipe complete with suitable bends, Tee, Socket, clamps, shadle, ete through the digged trench. Rate also including concealed Gl fitting where required Also provinding of outlet valve, tee-joint, bend and 25 mm dia G.1 pipe and fixing it every 6 mtr length with main pipe. The height of every rising cutlet point must be 300 mm above the surface level. The pipe line must be connected with both main supply and water Storage tank by fixing separate valve. Mtr. 100 15 Providing & fixing work of Name Plate made of 2mm thick aluminium sheets with covering of 3HP retroreflective sheeting of size 300x150 mm plate to be fixed with the help of nuts & bolts of already installed equipment , structures as per sample, provided by department free of cost. Nos. 12 16 Providing & fixing of Phase Plate equipment (R,Y,B) phase made of 2mm thick aluminium sheets with covering of 3HP retroreflective sheeting of size 5" dia plate to be fixed with the help of nuts & bolts of already installed equipment , structures as per sample, provided by department free of cost. Nos. 11 17 Calibration of metering system (03Ct+03PT+02 Energymeter) of 132 kV M/s GARDA SOLAR PRIVATE LIMITED bay at 220kV S/s Charkhari by reputed NABL accridated Laboratory with recomommanded instrument with proper calibration Certificate including prepration of test report at site Au 1 18 Necessary Interconnection for Data Transmission of already installed SAMAST compliant meters to LAN Switch upto DCU/Gateway and all other H/W, S/W per No. Job. 1 19 Misscellaneous work of Carriage of required materials like Control Cable, MS Flats, MS Round Bar,CT PT and other important items from different Sub-Stations under ETC Banda as per requirement. JOB 1 B Supply of Materials 1 Single Suspension Fittings Suitable for i ACSR Moose Nos 3.00 2 PG clamps suitable for - i Moose/Panther Nos 25.00 ii Moose/Moose Nos 35.00 3 Bus Post Clamps suitable for- i Moose Nos 12.00 4 Terminal connector suitable 145kV CT for MOOSE conductor Nos 3.00 5 Terminal connector suitable 145kV PT for MOOSE conductor Nos 3.00 6 Supply of Flexible Copper Bond made of electrolyte copper rope of size 37/7/0.457 having length 750mm tinned copper lug shall be pressed jointed both end of copper bond Nos. 30 7 Supply of Fire bucket stand made of angle iron, size 40X40X6 mm having arrangement for having 10 nos. buckets on suitable hooks made of M.S. sheets of 18 S.W.G. and printed with post office red enamel paint. The stand should be as per site requirement. Nos. 1 8 Supply of Fire bucket having 9 ltr. Capacity and painted with red color paint from outside & white color paint from inside written with FIRE on outer surface. Nos. 10 9 Supply of Hot dip galvanized Cable Tray 18 SWG having weight 225mm as per technical specification. RMT 58 10 Supply of Hot dip galvanized Cable Tray 18 SWG having weight 75mm as per technical specification. RMT 58 11 Portable AFF mechanical foam type Fire Extinguisher complete with initial charge hoose pipe and all other accessories and fittings as per IS 1024 trolley mounted 45/50 ltr capacity Nos. 2 12 Spacer suitable for Twin ACSR Moose conducter No. 20 13 Galvanized U Bolt 20mm dia. with double nut and washer Nos. 22 14 Cable dressing Saddle Clamp of size 25x3mm of aluminum flat with 200mm long bent suitable and having 2 No. holes at both end with galvanized nut bolt. Nos. 100 15 Cart wheel mounted Aluminium ladder as per UPPTCL technical specification Nos. 1 16 LAN Cable Km 0.1 17.1 40mm MS Rod for Main Earthmat RMT 40 17.2 40mm dia MS Electrodes (3 M Long) Nos 20 18 MS Flat for earthing i 75x10mm RMT 200 ii 50x6mm RMT 250 iii 25x6mm RMT 100 19 Supply of 70kN Antifog Disc Insulator Nos. 35
|
