Tender For Interior Furnishing Work For School At Vanakbara Bus Stop And School Near Vadlimata Temple At U.T ... in India

Work Detail

Tender For Interior Furnishing Work For School At Vanakbara Bus Stop And School Near Vadlimata Temple At U.T. Of Diu-2 Round stage_ Music room Provide and install a 3000 mm in diameter and 300 mm high, circular stage supported by 50 x 50 mm thick teakwood supports, as per the sizes mentioned in the drawing. The top surface consists of a backing 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick teakwood planks finished with one coat of lacquer and two coats of matte/satin/glossy melamine polish as per the approved sample. The plywood and teakwood planks were fixed to the teakwood frames. The sides are covered with 12 mm thick BWP flexible plywood (Green Ply, Everest or of equivalent make) and 12 mm melamine-polished teakwood beading. Heavy-duty plastic moulded buffers are to be provided at the bottom of the approved wooden supports. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 3 Working table_CCTV roomProvide and install the working table, made of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) on the tabletop and bottom supports, and 12 mm thick BWP plywood for drawers as per the sizes mentioned in the drawing. The tabletop surface to be finished with 1mm thick anti-scratch laminate, all the external surfaces to be finished with 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make), and internal surfaces and drawers to be finished with 0.8 mm thick off-white liner laminate (Century, Green Lam, Royal Touché or of equivalent make) as per the approved sample.All the edges will have 10 mm thick melamine-polished teakwood beading. The study table will include locks and drawer channels fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make).The drawer shutter will have recessed handles (details as per the drawing). Table will include cable management port and ventilation opening as specified in the drawing. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 4 Working table_Accounts room Provide and install the working table, made of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) on the tabletop and bottom supports, and 12mm thick BWP plywood for drawers as per the sizes mentioned in the drawing. The tabletop surface to be finished with 1 mm thick anti-scratch laminate, all the external surfaces to be finished with 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make), and internal surfaces and drawers to be finished with 0.8 mm thick off-white liner laminate as per the approved sample. All the edges will have 10 mm thick melamine-polished teakwood beading. The study table will include locks and drawer channels fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). The drawer shutter will have recessed handles (details as per the drawing). Table will include cable management port and ventilation opening as specified in the drawing.All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 5 Working table–‘a’_Computer lab tableProvide and install the table, using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). The support structure consists of 19 mm thick plywood, vertical and horizontal teakwood supports. Heavy-duty plastic moulded buffers to be provided at the bottom of supports. All the external and internal surfaces to have 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) with one coat of lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the edges will have melamine-polished teakwood beading. Table will include cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 6 Working table–‘b’_Social science lab table / Science lab tableProvide and install the table, using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). The support structure consists of 19 mm thick plywood, vertical and horizontal teakwood supports. Heavy-duty plastic moulded buffers to be provided at the bottom of the wooden supports. Provide 75-125µm functional powder-coated (Asian, ICA, or equivalent make) MS- ‘L’ angle as per size mentioned in drawing, with horizontal teakwood frame to support tabletop. All the external and internal surfaces have a 4 mm thick veneer with one coat of lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the edges have melamine-polished teakwood beading. Table will include cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 7 Working table– ‘c’_lab teacher’s table/lab discussion table/library discussion table Provide and install the table using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) on the table top and 19 mm thick BWP Plywood as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). The support structure consists of 19 mm thick plywood, vertical and horizontal teakwood supports. Heavy-duty plastic moulded buffers to be provided at the bottom of the wooden supports. Provide 75-125µm functional powder-coated (Asian, ICA, or equivalent make) MS- ‘L’ angle as per size mentioned in drawing, with horizontal teakwood frame to support tabletop. All the external and internal surfaces have a 4mm thick veneer with one coat of lacquer and approved melamine polish. All the edges have melamine-polished teakwood beading. Table will include cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 8 Working table–‘d’_Social science lab table / NCC roomProvide and install the table, using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). The support structure consists of 19 mm thick plywood, vertical and horizontal teakwood supports. Heavy-duty plastic moulded buffers to be provided at the bottom of supports. All the external and internal surfaces to have 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) with one coat of lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the edges will have melamine-polished teakwood beading. Table will include cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 9 Working table– ‘e’_Classroom teacher’s table / Staff room tableProvide and install the table using 25 mm and 19 mm thick BWR plywood (IS: 710 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). The support structure consists of 19 mm thick plywood, vertical and horizontal teakwood supports with one coat of lacquer and two coats of matt/satin/glossy finish melamine polish as approved by the architect, heavy-duty plastic moulded buffers to be provided at the bottom of supports. All the external and internal surfaces to have 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) with approved melamine polish. Table will include cable management port and ventilation opening as specified in the drawing. All the edges will have melamine-polished teakwood beading. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 10 Working table– ‘f’_Instructor cabin table + Side storageProvide and install the table, using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). Supports and drawers to be made of 19 mm and 12 mm thick plywood. Heavy-duty plastic moulded buffers are to be provided at the bottom of the plywood, while the 45° niche drawer handle edge will have 2 mm PVC beading of Rehau polymers or an equivalent make with a similar shade of approved polish. All the external surfaces have 4 mm thick veneer with one coat of lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the internal surfaces of the drawers will have 0.8 mm thick off-white liner laminate as per the approved sample. All the edges have melamine-polished teakwood beading. Provide 75-125µm functional powder-coated (Asian, ICA, or equivalent make) MS- ‘L’ angle as per size mentioned in drawing, with horizontal surface of plywood to support the tabletop. The table includes cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 11 Working table–‘g’_HM room table + Side storageProvide and install the table, using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). Supports and drawers to be made of 19 mm and 12 mm thick plywood. Heavy-duty plastic moulded buffers are to be provided at the bottom of the plywood, while the 45° niche drawer handle edge will have 2 mm PVC beading of Rehau polymers or an equivalent make with a similar shade of approved polish. All the external surfaces have 4 mm thick veneer with one coat of lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the internal surfaces of the drawers will have 0.8 mm thick off-white liner laminate as per the approved sample. All the edges have melamine-polished teakwood beading. Provide 75-125µm functional powder-coated (Asian, ICA, or equivalent make) MS- ‘L’ angle as per size mentioned in drawing, with horizontal surface of plywood to support the tabletop. The table includes cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 12 Working table– ‘h’_Admin room workstationProvide and install the table using 25 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The tabletop consists of 25 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make). Supports and drawers to be made of 19 mm and 12 mm thick plywood. Heavy-duty plastic moulded buffers are to be provided at the bottom of plywood supports. All the external and surfaces have 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) with one coat of lacquer and approved melamine polish. All the internal surfaces of the drawers will have 0.8 mm thick off-white liner laminate as per the approved sample. All the edges will have melamine-polished teakwood beading. The table includes cable management port and ventilation opening as specified in the drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 13 Working table– ‘i’_Conference room tableProvide and install the table using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 25 x 25 mm MS box section, 5 mm thick MS plate, and an MS ‘C’ channel as per the sizes mentioned in the drawing. The tabletop consists of 19 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), with 10mm thick melamine-polished teakwood beading on edges. The table is supported by 75-125µm functional powder-coated MS box section frame MS base plate support as per detailed drawing. MS plate supports including 75 mm diameter MS pipe and heavy-duty plastic-moulded buffers to be provided at the bottom. All MS frame surfaces are covered with 12 mm thick plywood and 4mm thick veneer with one coat of lacquer and two coats of matte/satin/glossy finish melamine polish as approved by the architect. Provision for pop up switchboard, cable management port and ventilation opening is to be included as specified in the drawing. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 14 Faculty dining table Type-"j"Provide and install a table using 25mm thick BWP plywood (IS:710 Grade of Century, Green ply, Everest or of equivalent make) for the table top and 6mm thick BWP plywoodfor underside as per sizes mentioned in the drawing. Finish the tabletop with 4mm thick veneer (Century, Green panel, Archid, Timex or of equivalent make) and apply one coat of lacquer and two coats of matte/satin/glossy finish melamine polish as approved by the architect. All the edges will have 6mm melamine-polished teakwoodbeading. The table will be supported with vertical wooden members and wooden frame below the table top finished with melamine-polish. The buffer strips to be provided at the bottom of the wooden supports. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 15 Library reception tableProvide and install the ‘L’-shaped table using 19mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The lower and upper tabletop consists 19 mm thick plywood and 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) with one coat of lacquer and two coats of matte/satin/glossy finish melamine polish as approved by the architect. Supports and drawers are to be made from 19mm and 12mm thick plywood. All the internal surfaces of the drawers will have 0.8 mm thick off-white liner laminate. The table includes 75 mm plywood skirting; 45° niche drawer handle with 2mm PVC beading of Rehau polymers or equivalent make with a shade similarto the approved polish. All the external surfaces have a 4 mm thick veneer with lacquer and approved melamine polish, while non-visible surfaces have one lacquer finish coat. All the edges have approved melamine-polished teakwood beading. The table includes cable management port and ventilation opening as specified in the drawing. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 16 Stackable table type- ‘a’Provide and assemble stackable table using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports as per detail shown in the drawing and finish 25 mm thick plywood table top with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix table top and legs as per detail drawing. Edges will have 10 mm thick melamine-polished teakwood beading. Rubber gaskets are provided at the table top base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 17 Stackable table type- ‘b’Provide and assemble stackable table using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports as per detail shown in the drawing and finish 25 mm thick plywood table top with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix table top and legs as per detail drawing. Edges will have 10 mm thick melamine-polished teakwood beading. Rubber gaskets are provided at the table top base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 18 Stackable table type- ‘c’Provide and assemble stackable table using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports as per detail shown in the drawing and finish 25 mm thick plywood table top with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix table top and legs as per detail drawing. Edges will have 10 mm thick melamine-polished teakwood beading. Rubber gaskets are provided at the table top base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 19 Stackable table type- ‘d’Provide and assemble stackable table using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports as per detail shown in the drawing and finish 25 mm thick plywood table top with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix table top and legs as per detail drawing. Edges will have 10 mm thick melamine-polished teakwood beading. Rubber gaskets are provided at the table top base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 20 Curved seating_ Music roomProvide and install curved and circular sitting furniture, as per sizes and shapes mentioned in the drawing, supported by teakwood frame supports. The top surface consists of a backing of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make), covered with 75 mm foam. Sides will be covered with 25 mm thick foam on 12 mm thick BWP flexible plywood (Green Ply, Everest or of equivalent make). The top and sides is to be finished with the selected fabric. The lower edge of the sitting area will be framed with 6 mm thick plywood for fabric fixation. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 21 Circular seating_ Music roomProvide and install curved and circular sitting furniture, as per sizes and shapes mentioned in the drawing, supported by teakwood frame supports. The top surface consists of a backing of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make), covered with 75 mm foam. Sides will be covered with 25 mm thick foam on12 mm thick BWP flexible plywood (Green Ply, Everest or of equivalent make). The top and sides is to be finished with the selected fabric. The lower edge of the sitting area will be framed with 6 mm thick plywood for fabric fixation. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 22 Seating outside computer labProvide and install column to column seating, supported by MS supports as per the detailed drawing. The top surface consists of teakwood planks fixed on 19 mm thick plywood BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make), supported by four brackets fabricated from 8 mm MS plates, as per design. Additionally, one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood planks and beading shall cover the MS supports with a seamless finish. All materials include adhesives and hardware must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 23 Waiting area seating_ Admin roomProvide and install a wall-to-wall seat, supported by MS supports as per the detailed drawing. The top surface consists of teakwood planks fixed on 19 mm thick plywood BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make), supported by 75-125µm functional powder-coated MS box sections and four brackets fabricated from 8 mm MS plates, as per design. Additionally, one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood planks and beading shall cover the MS box sections with a seamless finish. All materials include adhesives and hardware must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 24 Library racks type-‘a’ Provide and install a library rack using 8 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. All the external and internal surfaces have 4mm thick veneer with one coat of lacquer and two coats of matte/satin/glossy finish melamine polish as approved by the architect. All the edges have approved melamine-polished teakwood beading as per detailed drawing. The rack includes 75-125µm functional powder-coated MS name plates bolted onto shelves as per detailed drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 25 Library racks type-‘b’Provide and install a library rack using 8 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. All the external and internal surfaces have 4mm thick veneer with one coat of lacquer and two coats of matt/satin/glossy finish melamine polish as approved by the architect. All the edges have approved melamine-polished teakwood beading as per detailed drawing. The rack includes 75-125µm functional powder-coated MS name plates bolted onto shelves as per detailed drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 26 Type-"c" (single side racks)Provide and install a library rack using 8 mm and 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. All the external and internal surfaces have 4mm thick veneer with one coat of lacquer and two coats of matte/satin/glossy finish melamine polish as approved by the architect. All the edges have approved melamine-polished teakwood beading as per detailed drawing. The rack includes 75-125µm functional powder-coated MS name plates bolted onto shelves as per detailed drawing. A sample must be approved before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 27 Cupboard_Instructor’s cabin + seatProvide and install the Cupboard made of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The cupboard comprises two closed units separated by open shelves. The sides, bottom, shutter, and shelves are to be made of 12 mm, 19 mm and 25 mm thick plywood and back side to be made of 8 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate and all the external surface will have 1mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make), as approved by the architect. All the internal shelf edges will have 10 mm thick approved melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels and magnet fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). The shutter will have recessed handles and 8 mm Saint Gobain glass with flat edges to be fixed with a teakwood frame using silicon and teakwood beading as per the drawing. Additionally, a seating space as detailed in the drawing is featured at the back of the cupboard, assembled from 19 mm and 25 mm plywood (IS: 710 Grade of Century, Green Ply, Everest, or of equivalent make). This seating will be covered with 10 mm thick teakwood beading and 1 mm laminate (Century, Green Lam, Royal Touché or of equivalent make), as per selection. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC).All sizes as indicated in drawings. 28 Cupboard _ CCTV roomProvide and install an ‘L’-shaped cupboard made of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, bottom, shutter, and internal shelves are to be made of 12 mm, 19 mm, and 25 mm thick plywood and back side to be made of 8 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate and all the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make), as approved by the architect. All the internal shelf edges will have 10 mm thick approved melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). The shutter will have recessed handles and 8 mm Saint Gobain glass with flat edges to be fixed with a teakwood frame using silicon and teakwood beading with location and size as per the drawing. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 29 Cupboard _ Accounts room Provide and install a cupboard, made of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, bottom, shutter, and internal shelves are to be made of 12 mm, 19 mm and 25 mm thick plywood and the back side is to be made of 8 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate and all the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. All the internal shelf edges will have 10 mm thick approved melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnet fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). The shutter will have recessed handles and 8 mm Saint Gobain glass with flat edges to be fixed with a teakwood frame using silicon and teakwood beading with location and size as per the drawing. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 30 Cupboard types_Sports RoomProvide and install a cupboard, made in three parts using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matt/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, back, bottom, shutter, and internal shelves are to be made of 12 mm and 19 mm thick plywood. All the internal surfaces will have 0.8 mm thick liner laminate of VIR laminates (SF2001 off white), and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing. The center part of the cabinet includes drawer with veneer finish.All the internal shelf edges will have melamine-polished 10 mm thick teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). This also will include installing a writing board assembly, comprising a white board, niche for smart LCD and duster holder. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). 31 Cupboard types ‘a’_Admin roomProvide and install a cupboard, made with 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, back, bottom, shutter, and internal shelves are to be made of 12 mm and 19 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutter will have 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 32 Cupboard types ‘b’_Staff roomProvide and install a cupboard, made in two parts using 19 mm thick BWR plywood (IS: 710 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matt/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, back, bottom, shutter, and internal shelves are to be made of 12 mm and 19 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 33 Cupboard types ‘c’_Staff room / Atal Tinkering LabProvide and install a cupboard, made in two parts using 19 mm thick BWR plywood (IS: 710 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matt/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, back, bottom, shutter, and internal shelves are to be made of 12 mm and 19 mm thick plywood. All the internal surfaces will have 0.8 mm thick liner laminate of VIR laminates (SF2001 off white), and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have melamine-polished 10 mm thick teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 34 Cupboard types ‘d’_LibraryProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 35 Cupboard types ‘e’_Conference roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 36 Cupboard types ‘f’_Conference roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 37 Cupboard types ‘g’_Conference roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 38 Cupboard types ‘h’_Conference roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 39 Cupboard types ‘i’_Staff roomProvide and install a cupboard, made in two parts using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), according to the sizes of shelves mentioned in the drawing, with teakwood shutters on top finished with one coat of lacquer and two coats of matte/satin/glossy melamine-polish, as approved by the architect. The sides, back, bottom, lower shutters, and internal shelves are to be made of 12 mm and 19 mm thick plywood, as mentioned in the drawings. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnet fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 40 Cupboard types ‘j’_Admin roomProvide and install a cupboard, made in two parts using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polished teakwood shutters and shelves according to the sizes mentioned in the drawing. The sides, back, bottom, shutter, and internal shelves are to be made of 12 mm and 19 mm thick plywood. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 41 Cupboard types ‘k’_Staff roomProvide and install a cupboard, made in two parts using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), according to the sizes of shelves mentioned in the drawing, with teakwood shutters on top finished with one coat of lacquer and two coats of matte/satin/glossy melamine-polish, as approved by the architect. The sides, back, bottom, lower shutters, and internal shelves are to be made of 12 mm and 19 mm thick plywood, as mentioned in the drawings. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The lower shutter will have polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make), recessed handles, while the upper shutter includes 8 mm Saint Gobain glass with flat edges, fixed with a teakwood frame using silicon and teakwood beading as per detailed drawing.All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnet fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 42 Cupboard types ‘l’_Admin roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing. All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 43 Cupboard types ‘m’_Staff roomProvide and install a cupboard using 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) and 12 mm thick plywood for shelves according to the sizes mentioned in the drawing. All the internal surfaces will have 0.8 mm thick off-white liner laminate, and the external surfaces will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), as approved by the architect. The shutters will be finished with one coat of lacquer and two coats of matte/satin/glossy finish melamine- polished 4 mm thick veneer (Century, Green Panel, Archid, Timex, or of equivalent make) and will have recessed handles as per detailed drawing.All the internal shelf edges will have 10 mm thick melamine-polished teakwood beading. The cupboard will include locks, stoppers, hinges, powder-coated MS pipe, drawer channels, and magnate fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 44 Kitchen / pantry / Toilet / Lab: Under the counter cabinet :Provide and install the under the counter cabinet, made of 19 mm thick and 12 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The shutters and side supports are to be made with 19 mm thick plywood and 12 mm thick plywood to be used in the rear. All the external surfaces to have 1 mm thick laminate (Century, Green Lam, Royal Touché or equivalent make), as approved by the architect. All the internal surfaces to have 0.8 mm thick off-white laminate, as approved by the architect. The cabinet will include hinges and magnet fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). The cabinet shutter will have bare aluminium finish profile handles of the approved make. A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 45 Kitchen / pantry: Under the counter drawerProvide and install the under the counter drawer, made of 19 mm thick and 12 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make) as per the sizes mentioned in the drawing. The shutters are to be made with 19 mm thick plywood and 12 mm thick plywood to make the drawer boxes. All the external surfaces to have 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make) and all the internal surfaces and drawers to have 0.8 mm thick off-white laminate, as approved by the architect.The drawers will have channels fixed with necessary hardware (Hettich, Hafele, Blum, Ozone, or of equivalent make). Drawer shutters will have bare aluminium finish profile handles of the approved make. A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 46 Writing Board (Type -a )Provide and install a writing board assembly, comprising a white board and green sliding board using 19 mm and 12 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) with teakwood framing and aluminium sliding channels as per the sizes mentioned in the drawing. The assembly includes 8 mm thick frosted glass (etched finish with grid lines) with two coats of green enamel paint, framed with 38 mm wide sliding aluminium sections and polished teakwood beading along all edges. Provide a fixed white magnetic board (Alkon or of equivalent make) according to the sizes mentioned in the drawing. Necessary heavy-duty hardware shall be used for securing the aluminium sliding assembly. All the external surfaces to have 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make) and all the teakwood polished with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polish as approved by the architect. All the edges have approved 12mm thick melamine-polished teakwood beading as per detailed drawing. Additionally, fix the LCD TV as directed by the concerned department. The contractor shall package, transport, and install the LCD TVs, ensuring damage – free delivery. The scope encompasses timely completion, compliance with client instruction, a smart LCD stand on the back wall, chalk and duster holders, necessary studs, fasteners, and hardware. A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 47 Writing Board (Type -b)Provide and install a writing board assembly, comprising a white board, niche for smart LCD and duster holder using 19 mm and 12 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) as per the sizes mentioned in the drawing. The assembly includes teakwood frame and 12 mm thick melamine-polished teakwood beading with white magnetic board (Alkon or of equivalent make) according to the sizes mentioned in the drawing. All the external surfaces to have 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make) and all the teakwood polished with one coat of lacquer and two coats of matte/satin/glossy finish melamine-polish as approved by the architect. Additionally, fix the LCD TV as directed by the concerned department. The contractor shall package, transport, and install the LCD TVs, ensuring damage – free delivery. The scope encompasses timely completion, compliance with client instruction, a smart LCD stand on the back wall, chalk and duster holders, necessary studs, fasteners, and hardware. A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 48 Lectern/PodiumProvide and install a Lectern as per size mentioned in the drawing using 19 mm and 12 mm thick plywood (IS: 710 Grade of Century, Green Ply, Everest, or of equivalent make). The cabinet is divided horizontally into two parts. The cabinet is made with 12 mm thick plywood shutters. The external surface will have 1 mm thick laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect, and internal surfaces of plywood are polished with one coat of lacquer. The longer shutters shall be provided with PVD/ZINC-coated SS D-shaped handles with mortice lock externally and tower bolt internally on the opposite shutter. The shorter shutters shall be given aluminium knobs. 75-125µm functional powder-coated MS SHS (size mentioned in drawing) is to be provided at the all the corners and in the center of the total height. Melamine-polished teakwood beading is to be provided as shown in drawing. Table will include cable management port and ventilation opening as specified in the drawing. A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 49 Map Stand _Social science labAssemble a freestanding stand using 50 x 50 mm MS SHS, 5 mm thick MS plate and 5 mm thick solid bar as per the sizes mentioned in the drawing. Provide 600 mm wide support with rubber strips at the bottom fabricated with 50 x 50 mm MS SHS and 5 mm thick MS plate. Integrate 5 mm thick metal hooks, welded into the vertical supports of the stand as a map holder. Finish metal welds with grinding and sanding. Apply 75-125µm functional powder-coated for a durable and scratch-resistant finish. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 50 Stackable stool type-’a’ Provide and assemble stackable stool using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports and 25 mm thick plywood seating with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix seating top and legs as per detail drawing. Edges will have melamine-polished 10 mm thick teakwood beading. Rubber gaskets are provided at the seating base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 51 Stackable stool type-’b’ Provide and assemble stackable stool using 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make), 8 mm thick MS plate, 15 x 15 mm MS SHS and teakwood as per the sizes and shapes mentioned in the drawing. Fabricate legs by bending and appropriate welding of MS plate and Box sections, finishing with grinding and sanding. Apply 75-125µm functional powder-coating for a durable and scratch-resistant finish. Include teakwood buffers at the bottom of the supports, as per detail shown in the drawing and 25 mm thick plywood seating with 1 mm laminate (Century, Green Lam, Royal Touché, or of equivalent make), approved by the architect. Fix seating top and legs as per detail drawing. Edges will have melamine-polished 10 mm thick teakwood beading. Rubber gaskets are provided at the seating base for stacking. A sample will have to be made for approval before mass execution of the work. All materials and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 52 Chair type - 1Provide and install a rocking chair made of glass-reinforced concrete of approved make as per sizes mentioned in the drawing. The chair’s seating, hand rest and backrest shall be moulded in glass-reinforced concrete as one single entity, with pigment approved by the architect. The chair features rounded edges and sealed surfaces for outdoor durability. The support structure consists of an 18° bended MS plate with three coats of synthetic enamel paint of approved shade over a coat of zinc chromate primer, and MS base plate with rubber strips at the bottom as per the detailed drawing. MS plate supports include a compression spring for easy movement.A sample will have to be made for approval before mass execution of the work. All materials, including adhesives and hardware, must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC).All sizes as indicated in drawings.Colour to be approved by the Architect. 53 Chair type - 2 roviding and placing in position ergonomic medium back revolving office chair with AN-70 breathable mesh backrest, single-lock synchro tilt mechanism with tilt tension adjustment, and adjustable lumbar support. Chair to have one-way heightadjustable armrests made of polypropylene, a cushioned seat with high-density PU foam upholstered in fabric, and a sturdy nylon five-star base with twin-wheel castors for smooth mobility. Suitable for long working hours with optimal comfort and posture support. Finish and color as approved by the architect. Make: Featherlite Versa or approved equivalent 54 Chair type -3 Supplying and placing in position ergonomic high back executive mesh chair with integrated headrest, made with IS 20D breathable mesh for enhanced airflow and seating comfort. Chair shall have a multi-lock synchro tilt mechanism allowing multiple reclining positions, and one-way (height adjustable) polypropylene armrests. Seat to be upholstered with high-density PU foam and durable fabric. The base shall be a five-star black nylon structure with twin-wheel castors for smooth movement. Suitable for executive cabins or prolonged work use with ergonomic support. Finish and color as per architect approval. Make: Featherlite Liberate or approved equivalent 55 Chair type -4Supplying and placing ergonomically designed chairs suitable for library and laboratory use, with cushioned seat and back upholstered in durable fabric/leatherette for user comfort during prolonged sitting. Chair to have a strong powdercoated metal sledge base ensuring stability, low maintenance, and non-scratch movement on floor surfaces. Ideal for educational and institutional settings, with available color options including Black, White, Red, Orange, and Green (as approved by architect). Make: Featherlite Loop Cushion or approved equivalent 56 Chair type -5Supplying and placing in position ergonomically designed low back mesh office chair with AC-60 breathable mesh backrest and fabric upholstered high-density cushion seat. The chair shall be fitted with a centre tilt mechanism for basic recline functionality and fixed polypropylene armrests. Base to be made of durable nylon with twin-wheel castors for smooth mobility. Suitable for visitor seating, conference rooms, or short-duration workstations. Finish and color as approved by the architect. Make: Featherlite Smart or approved equivalent 57 Bed_Girls rest room area Provide and install a bed, made of 25 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or of equivalent make) for the bed top, 19 mm thick for supports and 12 mm thick for the bed back according to the sizes mentioned in the drawing. The external surfaces will have the 1 mm thick laminate (Century, Green Lam, Royal Touché or of equivalent make) and all the internal surface will have 0.8 mm thick off-white liner laminate, as approved by the architect.. Edges will have 2 mm PVC beading of Rehau polymers or equivalent make with similar shade of approved laminate. A sample must be approved before mass execution of the work. All materials, including of adhesive and hardware must be approved by the consultant as per the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 58 Pre – Primary school sofaProvide and install rectangular sitting furniture, as per sizes and shapes mentioned in the drawing, supported by teakwood frame supports. The top surface consists of a backing of 19 mm thick BWR plywood (IS: 303 Grade of Century, Green Ply, Everest, or equivalent make), covered with 75 mm foam. Sides will be covered with 25 mm thick foam with rounded edges on 12 mm thick BWP plywood (Green Ply, Everest or of equivalent make). The top and sides is to be finished with the selected fabric. The lower edge of the sitting area will be framed with 6 mm thick plywood for fabric fixation. All materials, including adhesives and hardware, must be approved by the consultant according to the detailed specifications in the drawing and as directed by the Engineer-in-Charge (EIC). All sizes as indicated in drawings. 59 HM Room Sofa / Conference room sofaSEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.Approved make: Godrej, bonton, Geeken or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 60 Student Desk Type - 1Providing, supplying and placing of Desk cum Bench N Seater. Its size shall be 1040x1060x625. Desk-Top Panel-All panels are made from 18mm thick Pre-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides. The panels have corners rounded for safety usageUnderstructure: All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thick(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thick(approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thick(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together. The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating. Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thick(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating. The storage shelves are made from 0.6 mm thick MS sheet(As per IS:513) fixed below the desk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thick MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The understructure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Countersunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986) Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of PP Glass filled (30%)Plastic Caps made of PP copolymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product. M6 high tensile TVS make bolt(Class 8.8) with glasss filled nylon level adjustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx 15mm.Approved make: Godrej, bonton or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 61 Student Desk Type - 2Providing, supplying and placing of Desk cum Bench N Seater. Its size shall be 1140x1095x710.Desk-Top Panel-All panels are made from 18mm thick Pre-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides. The panels have corners rounded for safety usageUnderstructure: All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thick(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thick (approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thick(approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together. The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating. Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thick(approx. 18 SWG) rectangular ERW tubes(As per IS:7138).The tubes are coated with min. 45 micron thickness of epoxy polyester coating. The storage shelves are made from 0.6 mm thick MS sheet(As per IS:513) fixed below the desk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thick MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The understructure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Countersunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on th top of round tubes for wooden panels fixing. They are made of PP Glass filled (30%)Plastic Caps made of PP copolymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glasss filled nylon level adjustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx 15mm.Approved make: Godrej, bonton or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 62 Student Desk Type - 3Providing, supplying and placing of Desk cum Bench N Seater. Its size shall be 1240 x 1130 x 760.Desk-Top Panel-All panels are made from 18mm thick Pre-laminated twin board (E1/P2 GRADE) with PVC edge banding on all sides. The panels have corners rounded for safety usageUnderstructure: All side metal frames and cross connectors are made from combination of 25.4 x1.2 mm thick(approx. 18 SWG) Round ERW tubes ,31.8 x 1.2 mm thick (approx. 18 SWG) Round ERW tubes and 28.6 x 1.2 mm thick (approx. 18 SWG) Round ERW tubes(As per IS:7138) which are welded together. The Welded structures and cross connectors are coated with min. 45 micron thickness of epoxy polyester coating. Back supports which are provided at the rear back are made of 50.8 x 25.4 x 1.2 mm thick (approx. 18 SWG) rectangular ERW tubes (As per IS:7138). The tubes are coated with min. 45 micron thickness of epoxy polyester coating. The storage shelves are made from 0.6 mm thick MS sheet(As per IS:513) fixed below the desk top panel and are coated with min. 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thick MS sheet(As per IS:513) and are coated with min. 45 micron thickness of epoxy polyester coating.The understructure is assembled using M6 trilobular screws(As per DIN 7500)with Zn blue plating.Compact Laminate seat and back panels are assembled using M6 Countersunk Trilobular screws(as per DIN 7500) with Zn Black Plating (As per IS 1573:1986)Spacers Are provided on the top of round tubes for wooden panels fixing. They are made of PP Glass filled (30%)Plastic Caps made of PP copolymer(3530 Grade) are also provided on the rear frames adding more aesthetic value to the product.M6 high tensile TVS make bolt(Class 8.8) with glass filled nylon level adjustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx. 15mm.Approved make: Godrej, bonbon or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 63 EPDM flooring Multicolour EPDM flooring for Pre school classroom. The interlocking tile to be 500 mm x 500 mm. The thickness of EPDM tile to be 25mm & tensile failure stress of 17MPa. Laying of tile with thin coat of water based adhesive. The sample to be approved by the Engineer in Charge (EIC). 64 RugProviding of the rug for HM rooms of the size 2000 x 3000 and placed as per the location provided by the architect. The rug should have vinyl rubber bottom. The sample to be approved by the architect. 65 Anti-Skid Door MatProviding of the door/rubber mat for boys/girls/handicap toilet placed as per the location provided by the architect. The mat should have anti-skid bottom. The sample to be approved by the architect 66 MDM Roll carpetHand woven reversible 100% natural cotton striped / roll carpet (Blue - Border, 600mm wide x 5m roll), washable, fade resistant, durable and easily foldable. 67 Carpet tile flooringProviding and laying Flotex floor covering (or approved equivalent), a high-performance textile flooring solution suitable for music rooms in schools. The flooring shall be made of dense nylon 6.6 fibers electrostatically flocked onto a waterproof PVC backing, offering excellent durability, acoustic absorption, slip resistance, and ease of maintenance. Flotex shall combine the resilience of a resilient floor with the comfort and acoustic benefits of a textile floor. The material shall be anti-microbial, allergy-friendly, stain-resistant, and suitable for high foot traffic educational areas. Flooring shall be laid with recommended adhesive on a properly prepared subfloor, ensuring neat joints and smooth finish. Color/Pattern: As per architect’s selection 68 Aluminium galvanized wooden finish ceilingProviding and fixing aluminium galvanized ceiling panels in 100mm / 150mm / 200mm width, with wood grain finish (teak/oak/walnut or approved), fixed on concealed GI/aluminium suspension system with all necessary accessories (trims, hangers, fasteners). Panels shall be pre-coated/powder-coated, rust-proof, and suitable for indoor ceiling applications. 69 Acoustic Wall panellingProvide and install acoustic panels as per approved design and sample by Architect. The panels shall feature fabric-wrapped high- density glass wool/wood wool/ combinations of foam and fabric/basophilic elements like cork and moss measuring 600 x 600/1200mm with a thickness of 25-50mm. Fixing of the panelling should be approved by the Engineer-in-Charge (EIC). 70 Ceiling panellingProvide and install medium-density fibreboard(MDF) acoustic panels for slab and wall applications. The perforated panels, manufactured from high-quality MDF with a density of 750-850 kg/cubic meter and thickness of 1 mm ( ½” to 1”), shall have a sound absorption coefficient of 0.5-0.8 and a noise reduction coefficient of 0.55 for a 3.12 sq.m area. The panels measure 190mm x 1190mm with 6mm perforation holes and shall be fixed using aluminium channels and hold clips. The sample must be approved by the Engineer-in-Charge (EIC). 71 Acoustic Baffle and cloud CeilingProvide Rockwool rigid baffles and clouds, manufactured from high-density rock wool, with specifications including: 1200 x 1200mm size, 40mm thickness and a Noise Reduction coefficient (NRC) of 0.9. The baffles and clouds shall be wrapped in a textured finish fabric, offering various colour and fabric options. Fixing shall be done using anchor bolts to secure the baffles to the slab and suspension system for the clouds. Fixing of the panelling should be approved by the Engineer-in-Charge (EIC). 72 Painting work on MS FabricationApply painting work on MS fabrication, including PU coating, touch-ups and surface rubbing to rectify poor finishes. This involves two or more coats of Deluxe Multi Surface Paint to achieve an even shade, applying two or more coats (@0.90 litter/10sqm) over a primer undercoat (@0.80 litter/10 sqm) to achieve an even shade on existing steel columns, following thorough surface cleaning, using materials from approved brands and manufacturers. 73 Roller BlindsProviding and fixing roller blinds with fabric of approved shade and design, mounted on heavy-dutyaluminum roller tube with powder-coated finish. The fabric shall be UV-resistant, dust-repellent, and fade-proof, suitable for interior applications,with smooth rolling action using a chain and clutch mechanism for manual operation. The blinds shall be fixed with appropriate MS/Aluminium brackets, end caps, and fittings for wall or ceiling mounting, as per site condition. Edges of the fabric shall be heat sealed or hemmed to prevent fraying.Material: Polyester fabric / Sunscreen / Blackout fabric (as specified)Color/Shade: As approved by architect 74 Dustbin Type - "a"Providing of the black finished stainless steel perforated open top waste bin of the size 175 x 250 for classroom, lab, toilets and girls rest room as per the location provided by the architect. The waste bin to be made of NON MAGNETIC SS 200 SERIES Thickness - 0.4 mm, Metallic Elegant look. The waste bin to have anti-slip base. The sample to be approved by the architect. The items shall be in working condition. Approved Make :IKEA, Mofna Industries pvt. ltd. 75 MirrorProviding and fixing bevelled edge mirror of required size and shape as per architectural drawings, made from 5mm thick high-quality float glass with polished bevelled edges (bevel width approx. 18–25mm). The mirror shall be fixed to the wall using concealed fixtures, stainless steel studs/spacers, or adhesive as per site condition, ensuring a secure and flush installation. All necessary fittings and supports shall be included in the scope. Approved Make: Saint-Gobain, Modiguard, or equivalent 76 Toilet paper holdersProviding and fixing wall-mounted toilet paper holder made of corrosion-resistant stainless steel with brushed/matte finish. The design shall be minimal and contemporary, suitable for modern toilet interiors. Holder to be fixed using concealed fasteners for a clean look. All necessary screws, wall plugs, and installation accessories to be included. Suitable for use in residential, commercial, or institutional toilets. Approved Make: IKEA (BROGRUND), Jaquar, Kohler, or equivalent 77 Soap Dispensers and dispenser holderProviding and fixing wall-mounted liquid soap dispenser complete with stainless steel holder, suitable for residential, commercial, or institutional toilets. The dispenser container shall be made of durable acrylic or frosted glass with a hand-operated pump mechanism. The holder shall be fabricated from corrosion-resistant stainless steel (SS 304 or equivalent) with a brushed finish, designed to securely support the dispenser. The unit shall be installed with concealed fasteners and shall include all necessary mounting hardware and accessories. Approved Make: Jaquar, Kohler, or equivalent 78 Wall clockProviding and fixing wall-mounted round analog clock of 380mm diameter (38 cm), with a clear, easy-toreaddial featuring bold hour and minute markings. The clock shall have a durable plastic frame and a front cover made of glass/acrylic,equipped with a silent quartz movement mechanism for smooth and noise-free operation. Battery-operated and suitable for classrooms,offices, or institutional spaces. Color and design as approved by architect. Approved Make: IKEA (Tagged model), Ajanta, or equivalent 79 Type - 1 SignagesSupply & fixing ONE 100mm in height Stainless Steel Cut-out (5mm Thick), displaying classroom number, name of room, etc., complete matter will be Laser Cut from natural SS with Matt Finish & Matt Lacquer, fitting directly on wall with 3M Double-Gum tape 80 Type - 2 SignageSupply & fixing reverseLit channel letter, displayingschool name as per your design in which letter will be 450mm in height, complete with all accessories i.e. 1.5” emboss Stainless Steel Matt Finish (0.8mm Thick) Letters with with Groove cut 25mm Thick Acrylic Letters assembled behind SS Letter, LED’s (Warm White or White), SMPS, L.T.Wire for inside Wiring etc. 81 Type - 3 SignageProviding and fixing of the evacuation diagram, made on acrylic sheet with eco-solvent print. The evacuation diagram to be of the size 297 x 210mm and made from 5mm thick acrylic sheet. The diagram to be printed on the sheet with the eco-solvent print. The diagram to be fixed on the surface with 3M adhesive tape as per the location provided by the architect. Diagram for printing in required format shall be provided by architect. 82 S.S. RailingProviding and fixing stainless steel (Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) and as directed by EIC. The rate to include all scaffolding and hoisting charges. 83 100mm foam mattressProviding of the 100mm thick foam mattress of the size 850 x 1700 as per the location provided by the architect. The foam mattress to include the layer of PU foam, a layer of Resitec foam, a layer of double layered quilting foam and a layer of knitted fabric as the top most layer. The sample to be approved by the architect. Approved Make: Sleepwell or equivalent 84 Notice Board: Providing and fixing wall-mounted notice board of size 900mm × 600mm (3 feet × 2 feet), constructedwith 12mm thick soft board mounted on 6mm thick BWR Grade plywood conforming to IS:303 (Century Ply or equivalent). The board surfaceshall be covered with fabric/felt cloth in approved color for pin-up use. The notice board shall be enclosed in a polished hardwood frame andfitted with a hinged front-opening 4mm thick clear glass shutter, complete with brass/SS hinges, magnetic catch, and handle. Suitable forsecure display of notices in educational or institutional spaces. 85 Soft BoardProviding and fixing pin-up soft board of size 2400mm × 1200mm (8 feet × 4 feet), comprising 12mmthick soft board mounted on 6mm thick BWR Grade plywood of IS:303 Century Ply or equivalent. The board surface shall be covered withfabric/felt cloth in approved shade, suitable for classroom and lab use. The board shall be finished with an anodized aluminium frame withmitred corners, fixed flush to wall with concealed fasteners and necessary supports. 86 Smart TVSITC of 65 inch Smart Interactive display true 4K UltraHD (3,840 × 2,160) resolution for outstanding details and stunning visuals. It should be IPS Panel with 3mm-thick toughened glass for added protection against scratches or screen damage, Anti-Glare + Anti-Fingerprint + Antimicrobial. with Pen including all required wall mounting stand and all accessoriesIt must equip front bezel USB-A, USB-C ports for quick connection to USB keyboards/mice, memory drives and data, High-speed Wi-Fi 6 connection, Bluetooth 5.2, Dual RJ45 ports. Brightness 400 cd/m² or above. 20-point touch, 18W x 2 (Stereo), OS Android v13 or above, Speakers: 18W x 2 (Stereo), 32GB Internal memory + 4GB RAMPreloaded software like whiteboard, screen share, screen annotation and recording tools, centralized device management through Remote Manager Cloud or Windows software, Browser, App Store, Media Player. Screen lock, Dual Network Environment. OPS: Intel® i5 Processor Iris® Xe Graphics, 8GB RAM, 256 GB name SSD, 3 nos. USB 3.0 ports,1 HDMI port, 1 DP interface,1 Type-C port, Support dual channel memory, Wi-Fi IEEE 802.11. Windows 11 Pro Licence. ISO 27001 Certified. 3 years warranty of Samsung, LG Panasonic, DELTA 87 Movable Softboard: Suppling, fabricating and installing movable soft board with anodized aluminium frame and high density 12mm thick softboard surface finished with approved fabric of Red/blue/brown/white colour. The Board shall be mounted on smooth castor wheels with locking mechanism for stability ensuring durability and ease of mobility. Dimension 2400 x 1200 with precise fitting and smooth edge for safety. 88 Metal Box Kitchen StorageProviding and supplying grain storage container fabricated from galvanized iron (GI) sheet, suitable foruse in school kitchen store under the Mid-Day Meal scheme. The container shall be made from 22–24 gauge GI sheet, rust-resistant and foodsafe, with a capacity to hold up to 100 kg of food grains (such as rice or wheat). The container shall be of cylindrical or rectangular shape (as approved), with a tight-fitting hinged or lift-off lid to protect contents from moisture, pests, and contamination. All edges shall be folded or crimped for safety and strength. 89 Metal Box Kitchen StorageProviding and supplying grain storage container fabricated from galvanized iron (GI) sheet, suitable foruse in school kitchen store under the Mid-Day Meal scheme. The container shall be made from 22–24 gauge GI sheet, rust-resistant and foodsafe, with a capacity to hold up to 20 kg of food grains (such as rice or wheat). The container shall be of cylindrical or rectangular shape (as approved), with a tight-fitting hinged or lift-off lid to protect contents from moisture, pests, and contamination. All edges shall be folded or crimped for safety and strength. 90 MDM Storage RacksProviding and placing in position storage rack fabricated from mild steel (MS) sections, suitable for the store area of a school kitchen under the Mid-Day Meal scheme. The rack shall be free-standing, made with MS tubular vertical supports and horizontal bracing, and shelves fabricated from 24-gauge (approx. 0.6mm thick) MS sheet, fixed or adjustable as per site condition. The entire structure shall be degreased, pre-treated, and finished with oven-baked powder coating of minimum 50–60 microns in approved color. The rack shall have a minimum of four shelves, with sufficient load-bearing capacity to store grains, containers, and kitchen supplies. All edges shall be smooth and safe to handle.Material: Mild Steel frame with 24-gauge MS sheet shelvesFinish: Powder-coated (min. 50–60 microns) in approved shadeSize: As per drawing / approx. 5"–6" height, 3"–4" length, 18"–24" depth 91 Dish RackProviding and fixing stainless steel dish rack made of SS 304 grade material, designed specifically for use in school kitchens for mid-day meal purposes. The rack shall be multi-tiered to accommodate large plates, glasses, and utensils, with proper drainage and a detachable drip tray to ensure hygiene. The design will include durable, corrosion-resistant stainless steel with smooth, easy-to-clean surfaces and rounded edges to prevent damage to the dishes. The rack shall be wall-mounted or free-standing based on the kitchen layout and shall include all necessary brackets, screws, and hardware for secure installation. 92 WoodProviding and supplying seasoned Indian Teak Wood of approved quality and grade (CP/MP or equivalent), free from warping, cracks, knots, or other defects, with uniform grain and texture. The wood shall be properly kiln/air dried with a moisture content not exceeding 12–14%, suitable for use in premium interior applications such as furniture, panelling, door frames, or customized joinery works. Rate to include loading, unloading, handling, and stacking at site. 93 Wall Table (VB_Bio) 7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns. Worktop is 19mm (+/- 2mm) thickJet Black Granite construction. Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle leg space and 1 no of 600mm wide corner leg space. Master uprights, uprights and height adjustable reagent racks,8 nos of one way LPG gas valves and 5 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 94 Island Table (VB_Bio)4880L X 1540D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 8 nos of 600mm wide 2 shutter 1 drawer units with 6nos of 600mm widemiddle legspace and 2 no of 600mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 4 nos of two way lpg valves and8 nos of stools are considered inthe same table. 14 nos of 6 module plate with 28 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 95 Wall Table (VB_Bio)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction. Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks ,6nos of one way lpg gas valves and 6 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 96 MS Apparatus Storage Cabinet (VB_Bio)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plate. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 97 Wall Table (VB_Physics)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, and electrical trunkings and 6 nos of stools are considered inthe same table. 17 nos of 6 module plate with 34 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 98 Island Table(VB_Physics)4880L X 1540D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 8 nos of 600mm wide 2 shutter 1 drawer units with 6nos of 600mm widemiddle legspace and 2 no of 600mm wide Corner legspace. Master uprights,electrical trunkings and8 nos of stools are considered inthe same table. 22 nos of 6 module plate with 44 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 99 Wall Table(VB_Physics)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns. Worktop is 19mm (+/- 2mm) thickJet Black Granite construction. Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, and electrical trunkings and 6 nos of stools are considered inthe same table. 17 nos of 6 module plate with 34 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 100 Full Height Acid/Corrosive Storage Cabinet(VB_Physics)1000 x 1500 x 486Full Height Acid/Corrosive Storage Cabinet (Resilience). Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 101 MS Apparatus Storage Cabinet(VB_Physics)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plate. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 102 Wall Table(VB_Chemistry)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 6 nos of one way lpg gas valves and 5 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 103 Island Table (VB_Chemistry)4880L X 1540D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 8 nos of 600mm wide 2 shutter 1 drawer units with 6nos of 600mm widemiddle legspace and 2 no of 600mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 4 nos of two way lpg gas valves and8 nos of stools are considered inthe same table. 14 nos of 6 module plate with 28 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 104 Wall Table (VB_Chemistry)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 6 nos of one way lpg gas valves and 5 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 105 MS Apparatus Storage Cabinet(VB_Chemistry)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plate. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 106 Wall Table (VD_Bio)6830L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered3 nos of 750mm wide 2 shutter sink unit including 3 no of PP sinks of size 560x355 with 3 water faucets, 2nos of 1500mm widemiddle legspace and 2 no of 750mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 4 nos of one way lpg gas valves and 6 nos of stools are considered inthe same table. 4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 107 Island Table (VD_Bio)4880L X 1540D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 4 nos of 750mm wide 2 shutter sink unit including 4 no of PP sink of size 560x355 with 4 water faucet, 2nos of 1500mm widemiddle legspace and 4 no of 750mm wide Corner legspace.Master uprights, uprights and height adjustable reagent racks, 3 nos of two way lpg gas valves and8 nos of stools are considered inthe same table,4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 108 Wall Table (VD_Bio) 6830L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered3 nos of 750mm wide 2 shutter sink unit including 3 no of PP sinks of size 560x355 with 3 water faucets, 2nos of 1500mm widemiddle legspace and 2 no of 750mm wide Corner legspace.Master uprights, uprights and height adjustable reagent racks, 4 nos of one way lpg gas valves and 6 nos of stools are considered inthe same table. 4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 109 MS Apparatus Storage Cabinet (VD_Bio)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plate. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 110 Wall Table (VD_Physics)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction. Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, electrical trunkings and 6 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 111 Island Table(VD_Physics)4880L X 1540D X 900H Floor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction. Considered with 8 nos of 600mm wide 2 shutter 1 drawer units with 6nos of 600mm widemiddle legspace and 2 no of 600mm wide Corner legspace. Master uprights,electrical trunkings and8 nos of stools are considered inthe same table. 22 nos of 6 module plate with 44 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 112 Wall Table(VD_Physics)7280L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 6 nos of 600mm wide 2 shutter 1 drawer units with 5nos of 600mm widemiddle legspace and 1 no of 600mm wide Corner legspace. Master uprights, electrical trunkings and 6 nos of stools are considered inthe same table. 12 nos of 6 module plate with 24 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 113 Full Height Acid/Corrosive Storage Cabinet(VD_Physics)1000 x 1500 x 486 Full Height Acid/Corrosive Storage Cabinet (Resilience). Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 114 MS Apparatus Storage Cabinet(VD_Physics)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plat. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 115 Wall Table(VD_Chemistry)6830L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered3 nos of 750mm wide 2 shutter sink unit including 3 no of PP sinks of size 560x355 with 3 water faucets, 2nos of 1500mm widemiddle legspace and 2 no of 750mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 4 nos of one way lpg gas valves and 6 nos of stools are considered inthe same table. 4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 116 Island Table (VD_Chemistry)4880L X 1540D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered with 4 nos of 750mm wide 2 shutter sink unit including 4 no of PP sink of size 560x355 with 4 water faucet, 2nos of 1500mm widemiddle legspace and 4 no of 750mm wide Corner legspace.Master uprights, uprights and height adjustable reagent racks, 3 nos of two way lpg gas valves and8 nos of stools are considered inthe same table,4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 117 Wall Table (VD_Chemistry)6830L X 770D X 900HFloor Based Cabinet with Metal Skirting powder coated withpure epoxy of thickness 40-50 microns.Worktop is 19mm (+/- 2mm) thickJet Black Granite construction.Considered3 nos of 750mm wide 2 shutter sink unit including 3 no of PP sinks of size 560x355 with 3 water faucets, 2nos of 1500mm widemiddle legspace and 2 no of 750mm wide Corner legspace. Master uprights, uprights and height adjustable reagent racks, 4 nos of one way lpg gas valves and 6 nos of stools are considered inthe same table. 4 nos of 6 module plate with 8 nos of 6/16A switch and sockets also maintained in the layout. Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender document Colour to be approved by the Architect. 118 MS Apparatus Storage Cabinet(VD_Chemistry)900W X560D X 2100HMS Apparatus Storage Cabinet with top cover plat.Approved make: Godrej or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 119 Lab Stool/ Drg. Stool- Specification: Size:H:710, Seat:H:550, D:300,Under Structure:-Made up of MS cold rolled close annealed,18G tube. Topmade of 18mm thick pre-laminated particle board. Side edges covered with teak wood beading duly polished. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. Approved make: Godrej, bonbon or as specified in the list of approved furniture manufacture in the tender documentColour to be approved by the Architect. 120 Kesariyaji Green MarbleProviding and laying kesariyaji green marble, 18-20 mm thick machine cut and polished to a smooth finish. Marble laid over a 1:4 cement mortar bed with white cement slurry, ensuring proper alignments and vein continuity. Joints to be filled with matching epoxy joint. 121 Wooden Laminate FlooringSupply and instakkation of 8mm thick wooden laminate flooring with a screatch-resistant, anti slip surface and click-lock joint system. Incudes foam/felt underlayment for sounfproofing and moisture resistance, skirting, trims and post-installation cleaning.

Contact Information