|
Tender For Design, Manufacturing, Providing, Fitting, Testing And Commissioning Of Various Mechanical And Electrical Equipment Of Lift Water Supply Scheme Rakhi Hygam Under Ut Capex (Earlier Jkidfc)-Supply, installation, commissioning and creation of pole mounted, outdoor type Electric Sub Station for Stage 1st a ,,Providing, fitting, testing and commissioning of voltage stabilizer 3. Dismantling of 07 Nos. of existing poles and Acsr Conductor at WSS Wadoora (Stage–II), including shifting and re-erection of 04 Nos. of poles at WSS Ningli Ghat and 03 Nos. of poles at WSS Checkipora Nowpora. The item also includes dismantling and shifting of 01 No. of pole at WSS Ningli Ghat to another location, as directed by the Engineer-in-Charge. The rate shall be inclusive of excavation, erection, alignment, and cement concreting at pole base in 1:2:4 mix as per REC specifications, complete in all respects, with 0.5 Cum per pole. 4. Providing and fitting of G.l V cross with top Bracket including clamps. 5. Providing and fitting of Galvanized nuts and bolts (approx I kg/pole). 6. Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative, creepage distance 320 mm. 7. Earthing complete by Gl Pipe 40 mm or Gl Rod 20 mm 2.5 mtr long through Gl Strip. 8. Providing and applying of Red Oxide coating. 9. Providing and applying Aluminum Paint coating. 10. Providing and fitting of Gl Channel/Angle/Flat of sizes including clamps. 11. Laying of departmental conductor along the line shown and designated by the Site Engineer at site, including necessary handling, straightening, alignment, and installation. 12. Providing of bamboo ladder 18 feet long along with 15 feet long Link rods and HT Glove pair 13. Providing and fitting of 9” x 9”exhaust fan with complete wiring in 1.5 mm cu wire through conduit and 6 A modular control complete job. Reputed Make for Stage 2nd 14. Supply of heavy duty hand Pallet 2.5 Ton capacity with PU wheels of reputed make.The said equipment is used for lifting/shifting of electromechanical gadgets in the scheme. The minimum fork height approx. 85 m and maximum fork height approx- 200 mm / as per design opproved. Job includes supply of heavy duty lifting sling belts 3m long 3 MT capacity -4 nos 15. Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole vide Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Colour Temperature: 4K - 6.5K Beam Angle: 120° - 170° Lumens: >12000 Operating Temperature: -20°C to 60°C The LED is pressure die cast aluminum housing with power coated finish and having Ingress Protection up to IP-68. The LED is properly fitted on the arm of the pole and connected to the copper as provided in the high mast pole. 16. Providing and installation of Junction Box with DP 32Amp MCB to serve as main switch for LED lighting including complete wiring or as per site requirement up to control at machine room. This job also includes P/F 3 of 16/6 amps each for premises luminary of reputed make. Further job includes providing / fitting 2.5 mm² multistranded single core 1100 volts, PVC insulated copper conductor through PVC conduit as service line from main panel as per site requirements. 17. Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work upto plinth level 1:2:4 with stone aggregate 20 mm nominal size. For concrete grouting of MS pipe/Channels/ISA/ foundation for concrete base frame 18. Providing, Installation, testing and commissioning of MU-G75 (Ampere Rating 45-75) factory fabricated pump control panel/switch gear protection equipment Horizontal pumping unit suitable having automatic star delta starter contractor type and should provide protection (like single phase reversing, over voltage, under voltage, under current) indicating lamps, push buttons for on off, metering module and selector switch suitable for 415 V 50 Hz 3 Phase AC Supply including necessary interconnections etc. as required. Make of Mug starter should be reputed make and confirming to ISI standards. 19. Providing, fitting and testing of 250 Amp. MCCB (04 Pole) with breaking capacity of 50KA of approved make as per damaged MCCB at site including extraction of damaged ones, transportation, loading, unloading, fitting and successful testing on no and full load at site. The job also includes p/F of thimbles as per site requirement.
|
