|
Tender For Supply Of Various Items At Iti Nalwa-Manual Motor Coil Winding Machine1. With step arbor winding speed, 60 to 100 rpm 2.5 digitmechanical counter 3.Wire Range: 18-46 SWG 4. Centre Distance : 190 mm 5. manully operated with wooden handle 6. Die casting stainless steel gear. 7. Body material cast iron. 8. IS 8783 (Part 4/Sec3)/ 1 2 Shaded Pole Motor 1 Fractional HP, 2 240 V, 50 Hz with copper winding, 3Dimensions: 48 x 70 mm, 4Shalf Diameter: 4.0mm, 5 Voltage: 230VAC, 50 Hz, 6No Load Speed: 2770 rpm, 7No Load Current: 0.096 A, 8Maximum Output Power: 2.38 W, 9Stall Torque: 8.87 mNm, 10 Life (typical) : 3000 hours, 11 Weight: 400 g, 12 Operating Temperature: -10 to 50 Degree C, 13 Storage Temperature: -20 to 100 degree C, 14Electrical Connection: Terminal, 15Torque: 10.79 (maximum power) 16Efficiency 16.50 % 3 4- Point D.C. Starter 1 For 2.5 KW DC motor 2 With NO volt coil & Over load protaction 3 Withbrass contacts 4Carrying handle 5 BTI-30 Terminalshould be provided for power supply,motorconnections should be brought out in front of starter. 4 Laser Light Pen 11.Laser Class: Class II (Safe for general workshop use) 2. Laser Wavelength: 650 nm (red) or similar visible light 3. Output Power: <1 mW (within Class II safety standard) 4. Beam Color: Red (typically) 5. Range: Up to 100 m (approx.) visible beam range 6. Power Source: 2 × AAA batteries / Rechargeable battery 7. Body Material: Aluminium alloy / robust plastic housing 8. Switch: On/Off push button 9. Size: Approx. 130 mm × 12 mm diameter (pen‑type form) 10. Weight: Approx. 30–50 g (with batteries) 11. Accessories: Batteries, cap/clip, instruction manual 5 Caliper outside Spring Joint 150mm Nominal Size (l) 75 mm 100 mm 150 mm 200 mm 250 mm 300 mm Max. Measuring Capacity 75 mm 100 mm 150 mm 200 mm 250 mm 300 mm Dia of Nominal (d) 5 mm 6 mm 7 mm 7 mm 8 mm 8 mm Fulcrum Dia (h) 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm Tip Thickness (s) 3 mm 3 mm 3 mm 4 mm 4 mm 4 mm Tip Width (w) 6 mm 8 mm 9.5 mm 11 mm 11 mm 11 mm Width (a) 40 mm 50 mm 76 mm 100 mm 125 mm 150 mm 6 Caliper inside spring joint 150mm Nominal Size (l) 75 mm 100 mm 150 mm 200 mm 250 mm 300 mm Max. Measuring Capacity 75 mm 100 mm 150 mm 200 mm 250 mm 300 mm Dia of Nominal (d) 5 mm 6 mm 7 mm 7 mm 8 mm 8 mm Fulcrum Dia (h) 20 mm 20 mm 20 mm 20 mm 20 mm 20 mm Tip Thickness (s) 3 mm 3 mm 3 mm 4 mm 4 mm 4 mm Tip Width (w) 6 mm 8 mm 9.5 mm 11 mm 11 mm 11 mm 7 Caliper odd-leg firm Joint 150mm Item’s Specifications:- 3.1Range: - 0 – 150 mm. 3.2Accuracy: - 0.5 mm. 3.3Material: - Legs, Screw & Nut Washer: - Carbon and alloy tools steel. 3.4Heat Treatment: - Measuring Face Hardness: - 650HV (±50HV) 3.5Finishing: - Polished. 3.6Nut & Joint:- Nut. 3.7Others: - Odd leg, Adjustable Tip, sturdy & corrosion resistance. 8 Prick Punch 100m1 Size: - dia 6x length 100 mm. 2 Tip angle: -60°. 3 Material:-Highcarbonsteel 4 KnurledBodyforgrip 5 Point Hardness:52-58 HRC 6 Head/FaceHardness:38-46 HRC 7 Finishing:- Polished finish. 8 Others:- Precision centered tip for accuracy. 9 Divider Spring Joint 150 mm Item’s Specifications:- 9.1 Range: - 0 – 150 mm. 9.2 Length of Legs:- 150 mm. 9.3 Joint type:- Spring. 9.4 Material: - (i) Legs: - Carbon and alloy tools steel. (ii) Spring: - Carbon spring steel. (iii) Fulcrum roller, Adjusting Screw and Nut Hardness: - 400-500 HV. (iv) Measuring Tip Hardness: - 650HV (±50HV) 9.6 Finishing: - Polished. 9.7 Others: - Adjustment Screw, sturdy & corrosion resistance. Fine adjusting nut should be knurled. 10 Universal Surface Gauge Item’s Specifications: 16.1 Size:- Spindle Height:-250mm. Spindle dia:- 10mm. Base:- 80x65 mm.(L x W). Fine Screw:- Adjustable . 16.2 Material:- Base- Case Hardened steel, Scriber- High carbon steel with size 150 mm x dia. 6 mm, spindle material: Stainless steel with case hardened and tempered. 16.3 Heat Treatment:- Scriber point hardened & tempered. 16.4 Finishing for base and spindle:- Chrome plating after machining. 16.5 Scriber Point Hardness: 52-58 HRC 16.6 Others:- Fine adjustment screw and clamping nut should be knurled . 11 File Half Round Smooth (150mm)26.1 Type of cut: Double cut 26.2 Length excluding tang (L): 150 mm 26.3 Width (b): 16 mm 26.4 Thickness (t): 4 mm 26.5 Length of taper (Ll): 50 (L/3) 26.6 Point thickness (t1): 4 mm 26.7 Length of tang (a): 50 mm 26.8 No. of up cut per cm: a) Front side: 20 b) Convex side: 19 26.9 General Requirements: a) The files shall generally conform to the shapes and dimensions. b) The teeth on the surfaces and sides shall be uniform. c) Safe edges shall be smooth and free from burrs. d) When held near the middle of file length and struck by a piece of steel, the files shall give a clear metallic ring. 26.10 Workmanship and Finish: File shall be well shaped and shall be reasonably straight. They shall be properly cleaned and shall not show cracks, scales, rust or other manufacturing defects. 26.11 Handles: The handles are required to be supplied with files, these shall conform to IS 2895. 26.12 Preservative Treatment and Packing: a) The files must be given a suitable rust preventive treatment before packing. b) File shall be packed in a plastic box. 26.13 Marking: Each file shall be stamped with manufacturer’s name/trade mark on the uncut portion of the file. 26.14 Material: High carbon steel as per IS3748 26.15 Hardness: 60 – 64 HRC 12 Caliper Transfer Inside Item’s Specifications:- 33.1 Range: - 0 – 150 mm. 33.2 Accuracy: - 0.5 mm. 33.3 Material: - Legs, Screw & Nut Washer: - Carbon and alloy tools steel. 33.4 Heat Treatment: - Measuring Face Hardness: - 650HV (±50HV) 33.5 Finishing: - Polished. 13 Tap Wrench (Adjustable)83.2 Wrench size for the taps: – M6, M8, M10, M12 as per syllabus. 83.3 Material: – Jaws:- Steel having tensile strength not less than 400 MPa. Handles and Body:- Malleable case iron according to IS2107:1977 83.4 Type: – Adjustable. 83.5 Hardness: - Jaws (working surface): 600 – 660 HV. 83.6 Others:- Supply in a wooden box, both ends of the handle should be knurled for proper griping. 14 Reamer AdjustableItem’s Specifications:- 70.1 Range: - Dia.- 10-20mm by1mm (11pcs. in a set). 70.2 Shape:- Straight flute. 70.3 Adjustable limit:- 0.8mm. 70.4 Material: - High speed steel. 70.5Hardness: - Cutting Portion: 760 – 900 HV Shank Portion: 240 HV min. 70.6 Others: -, High accuracy, long life, reamers should have 2 numbers of adjustable nuts to adjust the size, corrosion resistant, with square head to hold in handle, with adjustable handle and both ends of the handle should be knurled, ISI marked. 15 Parting Tool Holder with H.S.S. Blade 72.1 Size:- Blade- 1.5 x 5.5 x 63mm.(T x W x L). 72.2 Material (blade):- High speed steel. 72.3 Size of tool holder:- 25.4mm square shank x150mm length. 72.4 Material (tool holder):- High carbon steel. 72.5 Others: - Precision-designed, high strength, corrosion resistance, tool holder should have allen key for loading and unloading the parting blade, each tool holder shall be stamped with manufacturer’s name/trade mark. 16 Die Wrench 84.1 Die stock size for dies size:-dia6-12mm. 84.2 Material: - Steel or Malleable Iron. 84.3 Hardness: - 600 – 660 HV. 84.4 Others: - die stock (adjustable) suitable for die (dia.6-12), both ends of the die stock handle should be knurled, Adjusting screws in die stock should be of slotted pan head type with conical point. 17 CrimperIconic professional 59+ 18 plain switches 10x60 x60 mm color black, material fiber 19 switch stand height -13.8" material plastic 20 Lab coat40x60 cm 21 Ceramic straightening iron havells hs4122 rated volatege=100v-240v a.c 50hz power -55w-60w 22 Hair cutting scissors stainless steel,5.0 - 7.9 23 Braid 24 Cutting sheet polyster material length 140-160 cm width 120-140 cm water and chemical resistant 25 Barber scissors lenth 10 mm, lenth inch 3/8 "medium stainless steel 26 Thinning scissors lenth 5.5"-6.5"(14 cm -17 cm) stainless steel 27 Dye Brush flat wide bristles , vegs company , wider 2inch app 5cm 28 Dye bowl silicon,200-400 ml capacity, light weight 29 Dummy head on stand with slip on maxbell company 53 cm height, adjustable height rubberiza plastic material 360 ° rotable head 30 Dryer 1200-1800 w power(home), 220-224 v, 1800-2400 w professional 2-3 m cable length, 500-800 g weight ,Agaro campany 31 Re-bonding Boards heat resistant plastic material, 22-30cm length, 7-10 cm width, 220-250°c,heat resistant(temp) 32 Wax heater 150-600 w power , 220-240 v,40 °c-120 °c, wax hot size 50-800ml 33 Manicure bowl plastic material, 15-20cm size, 400-1500 ml capacity, light weight material. 34 Pedi spa tub 68-140 cm length, 44-72 cm width, fibre glassnet.
|
