Tender For One Panchayath One Playground-Development Of Playground At Sreekrishnapuram Grama Panchayath In O ... in India

Work Detail

Tender For One Panchayath One Playground-Development Of Playground At Sreekrishnapuram Grama Panchayath In Ottappalam Lac, Palakkad-Supply And Installation Of Outdoor Gym Equipment , Open Gym Equipment , Od271451/2025-2026 : Horse Rider - Supply And Installation Of Horse Rider Having The Following Specifications: Dimensions: (L X W X H) 1140 X 400 X 1400 Mm. Main Frame - Ø 114 Mm Od B Class Gi Pipe. Foundation Plate M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame Is Made By Ø 48 Mm Od B Class Gi Pipe. Seat Frame Is Made By Ø 48 Mm Od B Class Gi Pipe. Seat Position Must Be Horizontal To 110 -120 Degree. Link - Made Up Of Ø 48 Mm Od B Class G.I. Pipe. Angle Between Link And Ground Position Is 10-20 Degree. Handle - Ø 33 Mm Od B Class Gi Pipe. Paddle Vertical Support - Ø 60 Mm Od B Class Gi Pipe. Handle Frame- Ø 42 Mm Od B Class Gi Pipe Dually Bending Design. Foot Pipe - Ø 33 Mm Od B Class Gi Pipe. Support Frame 10 Mm Thick Ms Flat Is Used. Seat- Dimension 320 X 270 X 100 Mm Blow Moulded Wall Thickness 4Mm Material Hdpe. Bearing Bush Closing Cap Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin Made Of Ø 25 Mm M.S. Bright Bar. Grips - High Quality Rubber Ø 46 Mm Od. Circlips A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 60 To 70 Micron. Safety Instructions And Exercise Chart - Start &Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271452/2025-2026 : Air Walker - Supply And Installation Of Air Walker Having The Following Specifications: Dimensions: (L X W X H) 1190 X 380 X 1244 Mm. Main Frame- Ø 88 Mm Od &Quot;B&Quot; Class Gi Pipe Dually Bending Design. Foundation Plate- M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Ø 42 Mm Od Round Gi Pipe. Handle - Ø 33 Mm Od &Quot;B&Quot; Class Gi Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use To Support It. Top Closing Cap Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap'S - Pp / Nylon / Hdpe Material. Bracket - 8 Mm Thick Laser Profile Is Used To Support Paddle Frame. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Pin'S Ø 25Mm M.S. Bright Bar Pin. Circlips- A 24 Circlips Are Used For Assembly. Bearing Bushes -Ø 60 Mm Od Seamless Pipe. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271453/2025-2026 : Leg Press (Double) - Specifications: Dimensions: (L X W X H) = 1676 X 400 X1500 Mm. Main Frame - Ø 114 Mm Od ?B? Class Gi Pipe. Foundation Plate ? M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundations Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Link - Is Ø 60 Mm Od ?B? Class Gi Pipe. Seat Frame - Ø 42 Mm Od ?B? Class Gi Pipe. Leg Press Back Rest Should Be Angled In 120 -130 Degree. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 2 Mm Thick Use To Support It. Seat & Back Rest ? 380 X 275 X 60 Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Link Connected With Frame By 8 Mm Thick Laser Cutting Ms Profile. Top Closing Cap ? Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap?S- Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Pin? Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlip? A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271569/2025-2026 : Back Extension - Supply And Installation Of Back Extension Having The Following Specifications: Dimensions: (L X W X H) 1060 X 730 X 990 Mm. Main Frame - Made From Ø 88 Mm Od ?B? Class G.I. Pipe. Foundation Plate ? M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 42 Mm Od ?B? G.I Pipe. Seat Rest Pipe ? Ø 42 Mm Od ?B? Class G.I Pipe. Handle Pipe ? Ø 33 Mm Od ?B? Class G.I Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 3 Mm Thick Used To Support It. Footrest Pipe ? Ø 42 Mm Od ?B? Class G.I Pipe And 80 X 40 Mm Ms Rectangular Pipe. Closing Cap ? Pp / Nylon / Hdpe Material. Seat ? 360 X 300 X 2 Mm Thick M.S. Seat With Corner Fillet For Safety. Grips - High Quality Rubber Ø 46 Mm Od. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271454/2025-2026 : Chest Press (Double) - Supply And Installation Of Double Chest Press Having The Following Specifications: Dimensions: (L X W X H) 1955 X 710 X 1900 Mm. Main Center Pipe - Ø 114 Mm Od ?B? Class Gi Pipe. Foundation Plate ?M.S. Round Plate Of Ø 250Mm & 8 Mm Thick. Foundations Cover Cap- Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame - Made Up Of Ø 48 Mm Od ?B? Class G.I. Pipe. Handle - Made Up Of Ø48mm Od ?B? Class G.I. Pipe. Link - Made Up Of Ø 48 Mm Od ?B? Class G.I. Pipe. Seat & Back Rest ? 380 X 275 X 60 Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Bearing Bush Closing Cap?S? Pp / Nylon / Hdpe Material. Handle Must Be Connected With Frame By 8 Mm Laser Cutting Ms Profile. Top Closing Cap ? Dome Shape Made By Pp /Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin ? Made Up Of Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Grips - High Quality Rubber Ø 46 Mm Od. Circlips?A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271455/2025-2026 : Surfboard - Dimensions: (L X W X H) 1090 X 890 X 1390 Mm. Main Frame Made From Two Pipes Of Ø 114 Mm Od B Class Gi Pipe. Foundation Plate M.S. Round Plate Of Ø 250 Mm & 8Mm Thick. Connecting Pipe - Ø 88 Mm Od B Class Gi Pipe Is Used To Connect Both Main Frame Pipes At Top End And Ø 42 Mm Pipe Is Used To Connect At Bottom End. Handle - Ø 42 Mm And Ø 33 Mm Od B Class Gi Pipe. Support Pipe Ø 60 Mm Must Be Used To Support Leg Movement Frame. Leg Movement Frame Ø 42Mm Od B Class Gi Pipe. Footrest - Cast Iron 325 X 270 X 8 Mm Thick And M.S. Plate Of 250 X 200 X 2 Mm Thick Use For To Support It. Bracket - 8Mm Thick Laser Profile Is Used To Support Leg Movement Frame. Top Closing Cap Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Grips - High Quality Rubber Ø 46Mm Od. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin Made Of Ø 25Mm M.S. Bright Bar. Circlips A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In - Charge Before Installation.) , Od271467/2025-2026 : Rower - Supply And Installation Of Rower Having The Following Specifications: Dimensions: (L X W X H) = 1472 X 915 X 1040 Mm. Upper And Bottom Pipes Ø88Mm Od ?B? Class Gi Pipe. Foundation Plate ?M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle - Ø 33 Mm Od ?B? Class G.I Pipe. Angle Between Handle And Horizontal Surface Is 75 - 80 Degree. Linkages Ø 48 Mm Od ?B? Class G.I. Pipe. Seat & Back Rest ? 380 X 275 X 60Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Foot Resting Pipe - Ø 60 Mm Od ?B? Class G.I. Pipe. End Closing Cap ? Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps ? Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø250 Mm & 8Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe.Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Pin ? Ø 25 Mm M.S. Bright Bar Pin. Circlips? A 24 Circlips Are Used For Assembly. Bearing Bushes - Ø 60 Mm Od Seamless Pipe / Bar. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Grips ? High Quality Rubber 46 Mm Od. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.) , Od271489/2025-2026 : Triple Twister - Supply And Installation Of Triple Twister (Standing Position - 2 And Seating Position - 1) Having The Following Specifications: Dimensions: (L X W X H) 1500 X 1500 X1420 Mm. Main Frame &Ndash; Ø 114 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Seat Plate Support &Ndash; Ø 60 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Seating Ring- Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe Made By Rolling. Seating Ring Support - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Remaining Frame &Ndash; Is Made By 100 X 50 X 2.5 Mm Rectangular Pipe. Standing Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Seat Position And Other Two Standing Position Plates Are Fixed 120 Degrees Each From Other. Handle &Ndash; Ø 33 Mm &Ldquo;B&Rdquo; Class G.I. Pipe Made By Rolling. Top Closing Cap Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Bearing - Used Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin &Ndash; Madeup Of Ø 25Mm M.S. Bright Bar. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In - Charge Before Installation.) , Od271529/2025-2026 : Sky Walker - Supply And Installation Of Sky Walker Having The Following Specifications: Dimensions: (L X W X H) 1720 X 910 X 1700 Mm. Main Frame - Made Of Ø 88 Mm Od B Class Gi Pipe Dually Bending Design. Foundation Plate M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Vertical Support - Ø 42 Mm Od B Class Gi Pipe. Handle - Ø 33 Mm Od B Class Gi Pipe Dually Bending Design. Leg Movement Frame 50 Mm X 50 Mm X 2 Mm Thick Square Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use For To Support It. Top Closing Cap Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm M.S Pipe. And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In Cement Concrete Stock Below Ground Level. Grips - High Quality Rubber Ø 46 Mm Od. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin Made Of Ø 25Mm M.S. Bright Bar. Circlips A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Welded As Per Is Standards And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Foundation Shall Be M20 Cement Concrete And Design Shall Be Approved By The Engineer-In -Charge Before Installation.)

Contact Information