|
Tender For Miscellaneous Civil Repair Works To The Type Ii Staff Quarters At Bsnl Compound Civil Lines Roorkee.- 1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 3 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 5 Cement mortar 1:6 (1 cement : 6 coarse sand) 6 Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in foundations and plinth in : 7 Cement mortar 1:4 (1 cement : 4 coarse sand) 8 Providing and fixing to existing door frames. 9 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 10 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 11 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 12 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 13 40 mm thick with 20 mm nominal size stone aggregate 14 Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. 15 Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing the joints with white cement mixed with pigment of matching shade complete. 16 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 17 (i)Single socketed pipes. 18 75 mm diameter 19 110 mm diameter 20 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 21 Single tee without door 22 75x75x75 mm 23 Bend 87.5° 24 75 mm bend 25 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 26 75 mm 27 12 mm cement plaster of mix : 28 1:6 (1 cement: 6 coarse sand) 29 15 mm cement plaster on rough side of single or half brick wall of mix : 30 1:6 (1 cement: 6 coarse sand) 31 Finishing walls with Acrylic Smooth exterior paint of required shade : 32 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 33 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. 34 With cement mortar 1:4 (1cement: 4 coarse sand). 35 Renewing glass panes, with wooden fillets wherever necessary: 36 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). 37 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 38 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 39 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. 40 In cement mortar 41 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: 42 Of area 3 sq. metres and below 43 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 44 Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. 45 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 46 Kitchen sink without drain board 47 470x420 mm bowl depth 178 mm. 48 Providing and fixing white vitreous china water closet squatting pan (Indian type) : 49 Orissa pattern W.C. pan of size 580x440 mm 50 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. 51 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 52 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 53 10 litre capacity - White 54 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : 55 White solid plastic seat with lid 56 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 57 Semi rigid pipe 58 32 mm dia 59 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 60 15 mm dia. nominal bore 61 20 mm dia. nominal bore 62 25 mm dia. nominal bore 63 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anticorrosive bitumastic paint, cutting chases and making good the wall: 64 15 mm dia. nominal bore 65 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 66 15 mm nominal bore 67 20 mm nominal bore 68 Providing and fixing uplasticised PVC connection pipe with brass unions : 69 45 cm length 70 15 mm nominal bore 71 Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 72 15 mm diameter pipe. 73 20 mm diameter pipe. 74 25 mm diameter pipe. 75 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 76 Providing and fixing PTMT bib cock of approved quality and colour. 77 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. 78 Providing and fixing PTMT grating of approved quality and colour. 79 Circular type. 80 100 mm nominal dia. 81 Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 82 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. 83 Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.
|
